Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design pattern”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Next Generation Hydrogen Storage Vessels Enabled by Carbon Fiber Infusion with a Low Viscosity, High Toughness System

Onboard hydrogen storage for fuel cell vehicles holds considerable commercial promise which could be accelerated by lower cost storage vessels. In past years, the use of lower cost reinforcing fiber had been studied as an intuitive avenue to reduce vessel costs. Although the matrix resin does not play a large role in bearing stress loads in many areas of a filament wound pressure vessel, the matrix is relied upon for stress transfer between fibers and appears to play an important role in certain regions of the vessel construction such as the “tangent region” where the cylinder section transitions to the dome. Also, the matrix resin can play a role in the damage tolerance of vessels after impact events. Furthermore, the effect of dry spots or voids in the laminate can affect stress transfer between fibers in a manner that is challenging to quantify. Therefore, excess fiber must be used to account for this variability in performance. Unfortunately, in the case hydrogen pressure vessels the cost of the vessel is strongly dependent on the amount of carbon-fiber used in the design and manufacturing. An extensive investigation on the use of non-traditional fabrication processes enabled by an ultra-low viscosity thermoset resin (<10 cP) with high fracture toughness was conducted to determine the opportunity to reduce carbon-fiber usage and the associated high cost. The hypothesis was based on enabling a lower variation in vessel performance from a reduction in void defects (often found with traditional wet-winding) and a more defect-tolerant vessel resulting from use of a matrix resin with high fracture toughness. These two features were anticipated to justify a more aggressive design approach to the vessel winding pattern. From the work in this project, the potential use of the vacuum infusion approach to produce high quality vessels was validated. However, the team recognized the need to re-optimize the design, the dry-process, and the vacuum infusion process at each scale-up stage. During the planning phase, the critical need to re-optimize at this frequency was under-estimated. Also, the team identified the lack of industry testing standards on subscale parts for providing predictive value of vessel performance. Therefore, significant effort is needed to produce statistically significant numbers of vessels. To produce such numbers of vessels the project needed in retrospect to partner closely with a series vessel manufactures to develop a proof of concept production line to make the vessels. However, without the appropriate data, a manufacturing partner was challenging to fully engage during this timeline. New technologies relying on changing raw materials and manufacturing processes carry inherent risks. This project did not reach its ultimate objectives of demonstrated a vessel with lower carbon-fiber. But some companies expressed interest in learning from the partial successes of this project for future challenges in pressure vessel applications.

08 HYDROGEN↗

Affinity of small-molecule solutes to hydrophobic, hydrophilic, and chemically patterned interfaces in aqueous solution

Significance Increasing global population, urbanization, and climate change pose tremendous constraints on water availability. While membrane processes offer attractive, energy-efficient options, transformative advances in membrane technology are needed to enable reuse of poor-quality waters from diverse sources. This work brings fundamental understanding of solute–surface interactions to membrane phenomena, including selectivity and fouling. Molecular simulations reveal limitations of traditional predictive measures of solute–surface partitioning, suggesting alternative thermodynamic signatures for solute binding that highlight the contextual nature of hydrophobicity. An inverse design algorithm provides a tool to pattern membrane nanoscale chemistry to optimize solute affinity and selectivity. This work demonstrates how simulations can inform practical materials design for sustainable water treatment and, more broadly, many technologies involving water-mediated solute–surface interactions.

36 MATERIALS SCIENCE↗

Design and Characterization of Thin Stainless Steel Burst Disks for Increasing Two-Stage Light Gas Launcher Efficiency

Laser etched 300 series Stainless Steel Burst Disks (SSBD) ranging between 0.178 mm (0.007-in.) and 0.508mm (0.020-in.) thick were designed for use in a 17-caliber two-stage light gas launcher. First, a disk manufacturing method was selected using a combination of wire electrical discharge machining (EDM) to form the blank disks and laser etching to define the pedaling fracture pattern. Second, a replaceable insert was designed to go between the SSDB and the barrel. This insert reduced the stress concentration between the SSBD and the barrel, providing a place for the petals of the SSDB to open, and protecting the rifling on the inside of the barrel. Thereafter, a design of experiments was implemented to test and characterize the burst characteristics of SSBDs. Extensive hydrostatic burst testing of the SSBDs was performed to complete the design of experiments study with one-hundred and seven burst tests. The experiment simultaneously tested the effects of the following: two SSBD material states (full hard, annealed); five SSBD thicknesses 0.178, 0.254, 0.305, 0.381 mm (0.007, 0.010, 0.012, 0.015, 0.020-in.); two grain directions relative); number of times the laser etch pattern was repeated (varies between 5-200 times); two heat sink configurations (with and without heat sink); and, two barrel configurations (with and without insert). These tests resulted in the quantification of the relationship between SSBD thickness, laser etch parameters, and desired burst pressure. Of the factors investigated only thickness and number of laser etches were needed to develop a mathematical relationship predicting hydrostatic burst pressure of disks using the same barrel configuration. The fracture surfaces of two representative SSBD bursts were then investigated with a scanning electron microscope, one burst hydrostatically in a fixture and another dynamically in the launcher. The fracture analysis verified that both burst conditions resulted in a ductile overload failure indicated by transgranular microvoid coalescence, non-fragmenting rupture and mixed tensile and shear failure modes, regardless of the material states tested. More testing is underway to determine the relationship between SSBD burst pressure and projectile velocity.

Tylka, Jonathan M.↗

Cellular fluidics

The natural world provides many examples of multiphase transport and reaction processes that have been optimized by evolution. These phenomena take place at multiple length and time scales and typically include gas–liquid–solid interfaces and capillary phenomena in porous media. Many biological and living systems have evolved to optimize fluidic transport. However, living things are exceptionally complex and very difficult to replicate, and human-made microfluidic devices (which are typically planar and enclosed) are highly limited for multiphase process engineering. In this paper, we introduce the concept of cellular fluidics: a platform of unit-cell-based, three-dimensional structures—enabled by emerging 3D printing methods—for the deterministic control of multiphase flow, transport and reaction processes. We show that flow in these structures can be ‘programmed’ through architected design of cell type, size and relative density. We demonstrate gas–liquid transport processes such as transpiration and absorption, using evaporative cooling and CO 2 capture as examples. We design and demonstrate preferential liquid and gas transport pathways in three-dimensional cellular fluidic devices with capillary-driven and actively pumped liquid flow, and present examples of selective metallization of pre-programmed patterns. Our results show that the design and fabrication of architected cellular materials, coupled with analytical and numerical predictions of steady-state and dynamic behaviour of multiphase interfaces, provide deterministic control of fluidic transport in three dimensions. Cellular fluidics may transform the design space for spatial and temporal control of multiphase transport and reaction processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Real-valued composite filters for correlation-based optical pattern recognition

Advances in the technology of optical devices such as spatial light modulators (SLMs) have influenced the research and growth of optical pattern recognition. In the research leading to this report, the design of real-valued composite filters that can be implemented using currently available SLMs for optical pattern recognition and classification was investigated. The design of real-valued minimum average correlation energy (RMACE) filter was investigated. Proper selection of the phase of the output response was shown to reduce the correlation energy. The performance of the filter was evaluated using computer simulations and compared with the complex filters. It was found that the performance degraded only slightly. Continuing the above investigation, the design of a real filter that minimizes the output correlation energy and the output variance due to noise was developed. Simulation studies showed that this filter had better tolerance to distortion and noise compared to that of the RMACE filter. Finally, the space domain design of RMACE filter was developed and implemented on the computer. It was found that the sharpness of the correlation peak was slightly reduced but the filter design was more computationally efficient than the complex filter.

Rajan, P. K.↗

Analysis of aircraft wing-mounted antenna patterns

High frequency radiation patterns of aircraft wing mounted antennas are analyzed. Basic antenna types using ray optical techniques are studied. The aircraft is modelled in its most basic form so that this study is applicable to general type aircraft. The fuselage is modelled as a perfectly conducting finite elliptic cylinder. The wings and horizontal and vertical stabilizers are modelled as perfectly conducting "n" sided flat plates that can be arbitrarily attached to the fuselage or to themselves. The antenna locations are assumed to be on the surfaces of the wings at locations removed from engines and stores such that these effects are negligible. Volumetric patterns are calculated for several aircraft. The validity of the solution is shown by comparing the results against scale model measurements. The application of this solution to practical airborne antenna problems has shown its versatility in designing antennas and predicting their radiation patterns in an accurate and efficient manner.

Marhefka, R. J.↗

Continued Water-Based Phase Change Material Heat Exchanger Development

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development two full‐scale, Orion sized water‐based PCM HX's were constructed by Mezzo Technologies. These HX's were designed by applying prior research and experimentation to the full scale design. Design options considered included bladder restraint and clamping mechanisms, bladder manufacturing, tube patterns, fill/drain methods, manifold dimensions, weight optimization, and midplate designs. Design and construction of these HX's led to successful testing of both PCM HX's.

Hansen, Scott↗

Continued Water-Based Phase Change Material Heat Exchanger Development

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to meet the full heat rejection demands. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HX's do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development two full-scale, Orion sized water-based PCM HX's were constructed by Mezzo Technologies. These HX's were designed by applying prior research on freeze front propagation to a full-scale design. Design options considered included bladder restraint and clamping mechanisms, bladder manufacturing, tube patterns, fill/drain methods, manifold dimensions, weight optimization, and midplate designs. Two units, Units A and B, were constructed and differed only in their midplate design. Both units failed multiple times during testing. This report highlights learning outcomes from these tests and are applied to a final sub-scale PCM HX which is slated to be tested on the ISS in early 2017.

Hansen, Scott W.↗

Open Rotor Noise Shielding by Blended-Wing-Body Aircraft

This paper presents an analysis of open rotor noise shielding by Blended Wing Body (BWB) aircraft by using model scale test data acquired in the Boeing Low Speed Aeroacoustic Facility (LSAF) with a legacy F7/A7 rotor model and a simplified BWB platform. The objective of the analysis is the understanding of the shielding features of the BWB and the method of application of the shielding data for noise studies of BWB aircraft with open rotor propulsion. By studying the directivity patterns of individual tones, it is shown that though the tonal energy distribution and the spectral content of the wind tunnel test model, and thus its total noise, may differ from those of more advanced rotor designs, the individual tones follow directivity patterns that characterize far field radiations of modern open rotors, ensuring the validity of the use of this shielding data. Thus, open rotor tonal noise shielding should be categorized into front rotor tones, aft rotor tones and interaction tones, not only because of the different directivities of the three groups of tones, but also due to the differences in their source locations and coherence features, which make the respective shielding characteristics of the three groups of tones distinctly different from each other. To reveal the parametric trends of the BWB shielding effects, results are presented with variations in frequency, far field emission angle, rotor operational condition, engine installation geometry, and local airframe features. These results prepare the way for the development of parametric models for the shielding effects in prediction tools.

Guo, Yueping↗

Moiré engineering in van der Waals heterostructures

Isolated atomic planes can be assembled into a multilayer van der Waals (vdW) heterostructure in a precisely chosen sequence. These heterostructures feature moiré patterns if the constituent 2D material layers are stacked in an incommensurable way, due to a lattice mismatch or twist. This design-by-stacking has opened up the promising area of moiré engineering, a term that can be understood in two different perspectives, namely, (i) structural—engineering a moiré pattern by introducing twist, relative strain, or defects that affect the commensurability of the layers and (ii) functional—exploiting a moiré pattern to find and tune resulting physical properties of a vdW heterostructure. The latter meaning, referring to the application of a moiré pattern, is seen in the literature in the specific context of the observation of correlated electronic states and unconventional superconductivity in twisted bilayer graphene. The former meaning, referring to the design of the moiré pattern itself, is present in the literature but less commonly discussed or less understood. The underlying link between these two perspectives lies in the deformation field of the moiré superlattice. In this Perspective, we describe a path from designing a moiré pattern to employing the moiré pattern to tune physical properties of a vdW heterostructure. We also discuss the concept of moiré engineering in the context of twistronics, strain engineering, and defect engineering in vdW heterostructures. Although twistronics is always associated with moiré superlattices, strain and defect engineering are often not. Here, in this work, we demonstrate how strain and defect engineering can be understood within the context of moiré engineering. Adopting this perspective, we note that moiré engineering creates a compelling opportunity to design and develop multiscale electronic devices.

2D materials↗

Preliminary Design of a Deployable Optical Space Array Based on a Thickened Origami Flasher Pattern

Performance of space-based optics could be greatly enhanced by using deployable origami-based arrays, which can offer a large aperture size relative to their stowed volume when compared to traditional technology, thus improving imaging quality. In this work, we select, develop, and adapt the origami flasher pattern to serve as the foundation for a deployable array that shows promise for meeting stringent optical requirements. We apply a novel thickness accommodation technique, outline an approach for implementing the technique, improve stability by adjusting geometric characteristics of the pattern, and create an array of frames for housing optical elements in a co-planar configuration. Problems of non-rigid foldability in the flasher pattern are addressed. A prototype is created and tested. We find that the deployable flasher shows promise as an optical array. By following the guidelines in this work, more efficient and powerful optical arrays can be developed.

Jared Hunter↗

Design of semiconductor surface pits for fabrication of regular arrays of quantum dots and nanorings

We report a systematic computational study on the formation of complex nanostructures consisting of quantum dots and nanorings on surfaces of coherently strained thin films grown epitaxially on pit-patterned substrates. The analysis is based on self-consistent dynamical simulations according to a film surface evolution model that has been validated experimentally by comparison of its predictions with experimental observations on Ge films grown on Si pit-patterned substrates and is supported by linear stability theory that explains the film surface nanopattern formation as the outcome of a Stranski-Krastanow instability. Emphasis is placed on the design of conical pit patterns and the effects on the resulting film surface nanopattern of varying geometrical design parameters including film thickness, pit-pattern period, pit depth, pit opening diameter, and pit wall inclination. We demonstrate that varying the pit opening diameter and the pit wall slope leads to formation of complex nanostructures inside the pits of a regular pit pattern on the film surface, which include quantum dots, as well as single nanorings and multiple concentric nanorings that may or may not surround a central quantum dot inside each pit. Our simulation predictions demonstrate that the ordered nanostructure patterns forming on the film surface can be controlled precisely by tuning the geometrical parameters of the pits on the pit-patterned substrate. Our findings have important implications for designing optimal semiconductor surface patterns toward enabling future nanofabrication technologies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Space systems design at Utah State University - A total approach

An account is given of an Advanced Design Program, developed under the auspices of NASA/USRA, which uses a six quarter-hour multidisciplinary systems-design course to teach spacecraft design. The course integrates engineering skills with system-design principles, while emphasizing written and oral communications. The setting for such student efforts is patterned after existing high-tech spacecraft-design organizations. The classes address design tradeoff decisions, parametric studies, and design reviews, as well as project-continuations.

Redd, Frank J.↗

Computational Fluid Dynamics (CFD) Analysis for the Reduction of Impeller Discharge Flow Distortion

The use of Computational Fluid Dynamics (CFD) in the design and analysis of high performance rocket engine pumps has increased in recent years. This increase has been aided by the activities of the Marshall Space Flight Center (MSFC) Pump Stage Technology Team (PSTT). The team's goals include assessing the accuracy and efficiency of several methodologies and then applying the appropriate methodology(s) to understand and improve the flow inside a pump. The PSTT's objectives, team membership, and past activities are discussed in Garcia1 and Garcia2. The PSTT is one of three teams that form the NASA/MSFC CFD Consortium for Applications in Propulsion Technology (McConnaughey3). The PSTT first applied CFD in the design of the baseline consortium impeller. This impeller was designed for the Space Transportation Main Engine's (STME) fuel turbopump. The STME fuel pump was designed with three impeller stages because a two-stage design was deemed to pose a high developmental risk. The PSTT used CFD to design an impeller whose performance allowed for a two-stage STME fuel pump design. The availability of this design would have lead to a reduction in parts, weight, and cost had the STME reached production. One sample of the baseline consortium impeller was manufactured and tested in a water rig. The test data showed that the impeller performance was as predicted and that a two-stage design for the STME fuel pump was possible with minimal risk. The test data also verified another CFD predicted characteristic of the design that was not desirable. The classical 'jet-wake' pattern at the impeller discharge was strengthened by two aspects of the design: by the high head coefficient necessary for the required pressure rise and by the relatively few impeller exit blades, 12, necessary to reduce manufacturing cost. This 'jet-wake pattern produces an unsteady loading on the diffuser vanes and has, in past rocket engine programs, lead to diffuser structural failure. In industrial applications, this problem is typically avoided by increasing the space between the impeller and the diffuser to allow the dissipation of this pattern and, hence, the reduction of diffuser vane unsteady loading. This approach leads to small performance losses and, more importantly in rocket engine applications, to significant increases in the pump's size and weight. This latter consideration typically makes this approach unacceptable in high performance rocket engines.

Garcia, R.↗

Channel capacity enhancement by adjustable graphene-based MIMO antenna in THz band

This paper offers the design of a graphene-based MIMO antenna with an adjustable radiation pattern for THz communications. To make the radiation pattern adjustable a superstrate layer of graphene based patch, is added to the designed MIMO antenna which increases Channel Capacity. In addition to adjustable radiation pattern, the gain of antenna in the main lobe is also increased. The losses of THz channel is investigated and the angle of the main lobe of the designed antenna is set to the angle with the lowest loss. The channel capacity is evaluated and compared with the antenna without the superstrate layer. It is shown that channel capacity is significantly enhanced.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Controls-structures integrated design optimization with shape variations

The shape design variables have been introduced into the set of design variables of the Controls-Structure Integrated (CSI) Design of space-structures. The importance of the shape variations in improving the design (obtained with only control and sizing variables) has been aptly illustrated. Two different types of design variables that describe the shape variations of the structure have been introduced. In the first case, the nodal coordinates have been considered as design variables. This has the inherent difficulty of having too many design variables. This not only is time consuming but also memory intensive and may not yield a manufacturable shape to the structure. The second approach has been introduced to overcome this difficulty. The structure is allowed to vary in a particular pre defined pattern. The coefficients of these patterns are considered as the shape design variables. The eigenvalue and eigenvector sensitivity equations with respect to these coefficient design variables have been developed and are used to approximate the eigenvalues and eigenvectors in a perturbed design.

Koganti, Gopichand↗

Frequency-Selective Near-Field Radiative Heat Transfer between Photonic Crystal Slabs: A Computational Approach for Arbitrary Geometries and Materials

Here, we demonstrate the possibility of achieving enhanced frequency-selective near-field radiative heat transfer between patterned (photonic-crystal) slabs at designable frequencies and separations, exploiting a general numerical approach for computing heat transfer in arbitrary geometries and materials based on the finite-difference time-domain method. Our simulations reveal a tradeoff between selectivity and near-field enhancement as the slab-slab separation decreases, with the patterned heat transfer eventually reducing to the unpatterned result multiplied by a fill factor (described by a standard proximity approximation). We also find that heat transfer can be further enhanced at selective frequencies when the slabs are brought into a glide-symmetric configuration, a consequence of the degeneracies associated with the nonsymmorphic symmetry group.

36 MATERIALS SCIENCE↗