Search NASA⌕ Search

SEARCH · Search NASA

Results for “Disassembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Staked Bearing Removal Tool

Tool with assembled components expedites bearing replacement in aircraft, ground vehicles, and other applications. New tool cuts lip on one side to facilitate bearing replacement. After bearing retaining lip is cut away, bearing pressed out. Tool makes it possible to replace bearings without disassembling structure.

Berson, L. A.↗

Testing Bearings in Tight Spaces

Portable tool checks bushings and bearings in hard-to-reach places to ensure they are properly staked. Actuator plate with surfaces at 45 degrees to hydraulic cylinder shaft turns push or pull perpendicular to original direction. Tool makes unnecessary to disassemble equipment to gain access to parts.

Bird, R. G.↗

Ice as an Abrading Agent

Grit-blasting method makes unnecessary to disassemble equipment for cleaning. Stream of small, frozen pellets directed at assembly to be cleaned. Pellets consist of deionized-water ice, carbon dioxide ice, or another substance that does not react chemically with parts to be cleaned and leaves no residue. Method suited to cleaning titanium and parts that touch liquid oxygen.

Blow, R. K.↗

Bellows With Longitudinal Beams

Bellows assembled using two longitudinal side seams allow seam joints to be placed in axial directions of bellows. Design of particular importance in difficult situations where frequent assembly or repair required or in limited-access areas not desirable to disassemble total unit to replace one-piece bellows.

Garvin, W.↗

Design of a safe cylindrical lithium/thionyl chloride cell

Cell design criteria were established which can result in a safe lithium/thionyl chloride cell. A cell vent, a low area internal anode cell, cell balance and composition of the cathode-electrolyte solution were found to be important factors in the design of a safe cell. In addition to routine testing, both undischarged and discharged cells were subjected to electrical abuse, environmental abuse and mechanical abuse without disassembly.

Johnson, D. H.↗

Fabricating Underwater Electroacoustic Transducers

Use of retainer ring instead of adhesives simplifies assembly and disassembly. Underwater electroacoustical transducer assembly uses precast silicone rubber compressed between ceramic crystal and metal container. Removable retainer ring holds assembly in place. Method provides proper stress loading, speed and ease of assembly, and way of removing transducer without damaging crystal.

Ferguson, R. L.↗

Electromagnetic levitation coil fabrication technique for MSFC containerless processing facilities

A technique is described for more reproducible fabrication of electromagnetic levitation coils. A split mandrel was developed upon which the coil is wound. After fabrication the mandrel can be disassembled to remove it from the coil. Previously, a full day was required to fabricate a levitation coil and the success rate for a functional coil was only 50 percent. About eight coils may be completed in one day using the technique developed and 95 percent of them are good levitation coils.

Ethridge, E. C.↗

Intelligent editor/printer enhancements

Microprocessor support hardware, software, and cross assemblers relating to the Motorola 6800 and 6809 process systems were developed. Pinter controller and intelligent CRT development are discussed. The user's manual, design specifications for the MC6809 version of the intelligent printer controller card, and a 132-character by 64-line intelligent CRT display system using a Motorola 6809 MPU, and a one-line assembler and disassembler are provided.

Woodfill, M. C.↗

Failure Analysis of Nickel-hydrogen Cell Subjected to Simulated Low Earth Orbit Cycling

A nickel-hydrogen cell completed 10,080 simulated low earth orbit charge/discharge cycles at depths-of-discharge ranging from 50 to 80 percent prior to failure. The cell is of the Air Force design, rated at 50 ampere-hours, 8.9 cm (3.5 inches) in diameter. Upon disassembly, the end of the polysulfone core supporting the electrode stack was found to have fractured. This allowed the electrode stack to expand. A massive short was found at the inner diameter of the electrodes centered roughly at plate set 34 to 37 from the positive end of the electrode stack. The damaged area extended through approximately one third of the electrode stack, with the effect becoming progressively less with distance from plate set 34 to 37. Measured thicknesses of the positive plates were significantly greater than the initial specification values. The postulated cause of failure is that positive plate growth caused fracture of the shoulder from the end of the polysulfone core on which the electrodes are mounted. The electrode stack relieved and pressure points were created at the area near the inner diameter of the plates at the tab attachment. A short occurred at a pressure point between opposing plates and propagated to other electrode sets due to thermal and mechanical stresses caused by the short.

Mueller, V. C.↗

Noninvasive Fluid Level Sensor for Organometallic Sources

Two ultrasonic methods available for measuring level of organometallic liquid in stainless-steel (or other homogeneous solid) container. Methods require no disassembly or weighing of container. Commercially available ultrasonic flaw detectors, some of which have digital readouts and computer interfaces, used in techniques. Both methods used in crystal growth to determine level of liquids contained in sealed, opaque containers.

Gerdes, W.↗

Computing Relative Joint Positions of Robot Arms

Vector-algebra method developed for extracting Denavit-Hartenberg parameters for any assembled robot arm. Method for extracting relative joint geometry of robot arms useful to researchers who need data for existing robot arms for either validation of mathematical models or for studies involving actual control of these devices. Method, does not require robot arm to be disassembled, also useful in recalibration of misalined or bent robot arm and becomes useful industrial procedure. Merit of method is errors not propagated.

Barker, L. K.↗

Initial Sailplane Project: The RP-1

The annual static loading tests were made on the assembled wing/fuselage structure of the RP-1 sailplane. Simple wing bending and wing bending/torsion tests up to about four G's were made, using sand bag loading on the inverted aircraft. Bending a torsion deflections were measured and compared to those obtained in previous years' tests. It appears that the structure is retaining its original strength and stiffness very well. This aircraft has been disassembled and stored on the Jonsson Engineering Center under ambient, indoor conditions of temperature and humidity.

Source record↗

Second Sailplane Project: The RP-2

Progress has been made on the design fabrication and installation of a tension carry-through linkage between the aft parts of the port and starboard wings to resist forward bending deflection on the RP-2 sailplane. In addition, towhook/release mechanisms, landing gear and wheel brake assembly, compound curved sandwich composite fuselage shells and an enclosed trailer to house and transport the complete disassembled aircraft, have all undergone various stages of design, fabrication, installation and testing.

Source record↗

The Design and Use of Subtasks in Part Training and Their Relationship to the Whole Task

The part versus whole training is discussed. Common sense dictates that a massive body of knowledge should not be taught as a whole. For the same reason, if a part of the task is very difficult, one should not go over the task in its entirety. Repetitive training on the difficult part should lead to better results. Several part training methods were developed, including: pure part, progressive part, repetitive part, retrogressive and isolated parts. The question was posited whether training on parts of a task is a beneficial enterprise. The way the task will be disassembled for the part training needs to be determined. It is argued that the effectiveness of part training depends on the degree to which a task is decomposable.

Mane, A. M.↗

Solid rocket booster retrieval operations

Solid Rocket Booster Retrieval operations are discussed in detail. The recovery of expended boosters and associated hardware without damage attributable to retrieval procedures is the main goal. The retrieval force consists tof ship's personnel and retrieval team members, each of whom has been trained and is highly skilled in multi-faceted operations. The retrieval force is equipped with two specially-built, highly maneuverable ships outfitted with parachute reels, retrieval cranes, towing winches, large volume-low pressure air compressors, SCUBA diving gear, inflatable boats with outboard motors and diver-operated SRB dewatering devices. The two ships are deployed in sufficient time to conduct an electronic and visual search of the impact area prior to launch. Upon search completeion, each ship takes station a safe distance from the predetermined impact point initiating both visual and electronic search in the direction of flight path, ensuring SRB acquisition at splashdown. When safe, the ships enter the impact area and commence recovery of all floating flight hardware which is subsequently returned to the Disassembly Facility for refurbishment and reuse. Retrieval techniques have evolved in parallel with equipment and flight hardware configuration changes. Additional changes have been initiated to improve personnel safety.

Rasmussen, A. M.↗

Reusable rocket engine turbopump condition monitoring

Significant improvements in engine readiness with attendant reductions in maintenance costs and turnaround times can be achieved with an engine condition monitoring system (CMS). The CMS provides real time health status of critical engine components, without disassembly, through component monitoring with advanced sensor technologies. Three technologies were selected to monitor the rotor bearings and turbine blades: the isotope wear detector and fiber optic deflectometer (bearings), and the fiber optic pyrometer (blades). Signal processing algorithms were evaluated and ranked for their utility in providing useful component health data to unskilled maintenance personnel. Design modifications to current configuration Space Shuttle Main Engine (SSME) high pressure turbopumps and the MK48-F turbopump were developed to incorporate the sensors.

Hampson, M. E.↗

Nickel-hydrogen Cell Test Program Summary

Three prototype 50 ampere-hour (Ah) nickel-hydrogen cells of the Air Force Wright Aeronautical Laboratories (AWFAL) design were cycled to failure. A summary of the life cycling tests and failure analyses of the cells are presented. The cells were cycled in a simulated low earth orbit regime at depths of discharge ranging from 25 to 80 percent. Trend data, such as end of discharge voltage and cell capacity, was recorded during test. Cells 1, 2, and 3 completed 17167, 2473, and 10080 charge/discharge cycles, respectively, prior to failure. All failed due to internal shorts, and were disassembled to determine cause of failure.

Mueller, V. C.↗

Voyager 0.2-lbf thruster valve assembly short pulse test report

The short pulse width testing completed on the Voyager 0.2-lbf thruster value assemblies (T/VA's) and the disassembly and inspection of T/VA S/N 020 is reported. The purpose for performing the short pulse width testing on Voyager 0.2-lbf thruster valve assemblies (T/VA's) was to determine: (1) impulse bit versus electrical pulse width; (2) impulse bit variations versus electrical pulse width; and (3) whether the short pulses decrease thruster life.

Johnson, D. R.↗