Search NASA⌕ Search

SEARCH · Search NASA

Results for “EXPERIMENTAL VERIFICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Evaluation of propellant tank insulation concepts for low-thrust chemical propulsion systems

An analytical evaluation of cryogenic propellant tank insulations for liquid oxygen/liquid hydrogen low-thrust 2224N (500 lbf) propulsion systems (LTPS) was conducted. The insulation studied consisted of combinations of N2-purged foam and multilayer insulation (MLI) as well as He-purged MLI-only. Heat leak and payload performance predictions were made for three Shuttle-launched LTPS designed for Shuttle bay packaged payload densities of 56 kg/cu m, 40 kg/cu m and 24 kg/cu m. Foam/MLI insulations were found to increase LTPS payload delivery capability when compared with He-purged MLI-only. An additional benefit of foam/MLI was reduced operational complexity because Orbiter cargo bay N2 purge gas could be used for MLI purging. Maximum payload mass benefit occurred when an enhanced convection, rather than natural convection, heat transfer was specified for the insulation purge enclosure. The enhanced convection environment allowed minimum insulation thickness to be used for the foam/MLI interface temperature selected to correspond to the moisture dew point in the N2 purge gas. Experimental verification of foam/MLI benefits was recommended. A conservative program cost estimate for testing a MLI-foam insulated tank was 2.1 million dollars. It was noted this cost could be reduced significantly without increasing program risk.

Kramer, T.↗

Evaluation of propellent tank insulation concepts for low-thrust chemical propulsion systems: Executive summary

Cryogenic propellant tank insulations or liquid oxygen/liquid hydrogen low-thrust 2224N (500 lbf) propulsion systems (LTPS) were assessed. The insulation studied consisted of combinations of N2-purged foam and multilayer insulation (MLI) as well as He-purged MLI-only. Heat leak and payload performance predictions were made for three shuttle-launched LTPS designed for shuttle bay packaged payload densities of 56 kg cu/m (3.5 lbm/cu ft), 40 kg/cu m (2.5 lbm/cu ft) and 24 kg/cu m (1.5 lbm/cu ft). Foam/MLI insulations were found to increase LTPS payload delivery capability when compared with He-purged MLI-only. An additional benefit of foam/MLI was reduced operational complexity because orbiter cargo bay N2 purge gas could be used for MLI purging. Maximum payload mass benefit occurred when an enhanced convection, rather than natural convection, heat transfer was specified for the insulation purge enclosure. The enhanced convection environment allowed minimum insulation thickness to be used for the foam/MLI interface temperature selected to correspond to the moisture dew point in the N2 purge gas. Experimental verification of foam/MLI benefits was recommended. A conservative program cost estimate for testing a MLI-foam insulated tank was 2.1 million dollars. This cost could be reduced significantly without increasing program risk.

Kramer, T.↗

A TWT amplifier with a linear power transfer characteristic and improved efficiency

A novel method called "Dynamic Velocity Taper' to linearize the Pout versus Pin transfer characteristic that does not require any extraneous circuitry or tuning, has large bandwidth capabilities ( 10 percent) and offers also an increase in the intrinsic traveling wave tube (TWT) efficiency by 1 to 2 dB is described. In addition, the method permits the TWT to be operated at or near the synchronous voltage (b plus or minus o) which produces a flat small and large signal gain responses and low AM to PM conversion. The physics of the method and experimental verification are given. The implementation should have a significant impact on TWT performance and increase the channel capacity of communication satellites.

Kosmahl, H. G.↗

ECUT: Energy Conversion and Utilization Technologies program. Heterogeneous catalysis modeling program concept

Insufficient theoretical definition of heterogeneous catalysts is the major difficulty confronting industrial suppliers who seek catalyst systems which are more active, selective, and stable than those currently available. In contrast, progress was made in tailoring homogeneous catalysts to specific reactions because more is known about the reaction intermediates promoted and/or stabilized by these catalysts during the course of reaction. However, modeling heterogeneous catalysts on a microscopic scale requires compiling and verifying complex information on reaction intermediates and pathways. This can be achieved by adapting homogeneous catalyzed reaction intermediate species, applying theoretical quantum chemistry and computer technology, and developing a better understanding of heterogeneous catalyst system environments. Research in microscopic reaction modeling is now at a stage where computer modeling, supported by physical experimental verification, could provide information about the dynamics of the reactions that will lead to designing supported catalysts with improved selectivity and stability.

Voecks, G. E.↗

Holographic aids for internal combustion engine flow studies

Worldwide interest in improving the fuel efficiency of internal combustion (I.C.) engines has sparked research efforts designed to learn more about the flow processes of these engines. The flow fields must be understood prior to fuel injection in order to design efficient valves, piston geometries, and fuel injectors. Knowledge of the flow field is also necessary to determine the heat transfer to combustion chamber surfaces. Computational codes can predict velocity and turbulence patterns, but experimental verification is mandatory to justify their basic assumptions. Due to their nonintrusive nature, optical methods are ideally suited to provide the necessary velocity verification data. Optical sytems such as Schlieren photography, laser velocimetry, and illuminated particle visualization are used in I.C. engines, and now their versatility is improved by employing holography. These holographically enhanced optical techniques are described with emphasis on their applications in I.C. engines.

Regan, C.↗

Analysis and testing of a new method for drop size measurement using laser scatter interferometry

Research was conducted on a laser light scatter detection method for measuring the size and velocity of spherical particles. The method is based upon the measurement of the interference fringe pattern produced by spheres passing through the intersection of two laser beams. A theoretical analysis of the method was carried out using the geometrical optics theory. Experimental verification of the theory was obtained by using monodisperse droplet streams. Several optical configurations were tested to identify all of the parametric effects upon the size measurements. Both off-axis forward and backscatter light detection were utilized. Simulated spray environments and fuel spray nozzles were used in the evaluation of the method. The measurements of the monodisperse drops showed complete agreement with the theoretical predictions. The method was demonstrated to be independent of the beam intensity and extinction resulting from the surrounding drops. Signal processing concepts were considered and a method was selected for development.

Bachalo, W. D.↗

Fracture modes in notched angleplied composite laminates

The Composite Durability Structural Analysis (CODSTRAN) computer code is used to determine composite fracture. Fracture modes in solid and notched, unidirectional and angleplied graphite/epoxy composites were determined by using CODSTRAN. Experimental verification included both nondestructive (ultrasonic C-Scanning) and destructive (scanning electron microscopy) techniques. The fracture modes were found to be a function of ply orientations and whether the composite is notched or unnotched. Delaminations caused by stress concentrations around notch tips were also determined. Results indicate that the composite mechanics, structural analysis, laminate analysis, and fracture criteria modules embedded in CODSTRAN are valid for determining composite fracture modes.

Irvine, T. B.↗

Quantum shot noise in tunnel junctions

The current and voltage fluctuations in a normal tunnel junction are calculated from microscopic theory. The power spectrum can deviate from the familiar Johnson-Nyquist form when the self-capacitance of the junction is small, at low temperatures permitting experimental verification. The deviation reflects the discrete nature of the charge transfer across the junction and should be present in a wide class of similar systems.

Ben-Jacob, E.↗

A numerical procedure for predicting creep and delayed failures in laminated composites

A numerical procedure is described for predicting the viscoelastic response of general laminates. A nonlinear compliance model is used to predict the creep response of the individual laminae. A biaxial delayed failure model predicts ply failure. The numerical procedure, based on lamination theory, increases by increments through time to predict creep compliance and delayed failures in laminates. Numerical stability problems and experimental verification are discussed. Although the program has been quite successful in predicting creep of general laminates, the assumptions associated with lamination theory have resulted in erroneous bounds on the predicted material response. Delayed failure predictions have been conservative. Several improvements are suggested to increase the accuracy of the procedure.

Dillard, D. A.↗

A new multiple beam satellite antenna for 30/20 GHz communications coverage of CONUS-experimental evaluation

Additional frequency bands are needed to satisfy requirements related to the rapid growth of satellite communications, and the utilization of the 30/20 GHz frequencies is being considered. The present investigation is concerned with the experimental verification phase of an antenna technology study sponsored by NASA. The feasibility of narrow (0.3 degree) directive beam scanning over the entire continental U.S. (CONUS) from a single antenna at 30/20 GHz is demonstrated. The POC (Proof-of-Concept) model is based on an employment of an offset shaped dual reflector optics. The main reflector and the subreflector are both fabricated from aluminum. Attention is given to feed array and beam-forming network, multiple beam antenna range tests, an analysis, and test results.

Smoll, A. E.↗

A TWT amplifier with a linear power transfer characteristic and improved efficiency

A novel method called 'Dynamic Velocity Taper' to linearize the Pout versus Pin transfer characteristic that does not require any extraneous circuitry or tuning, has large bandwidth capabilities (10 percent) and offers also an increase in the intrinsic traveling wave tube (TWT) efficiency by 1 to 2 dB is described. In addition, the method permits the TWT to be operated at or near the synchronous voltage (b plus or minus o) which produces a flat small and large signal gain responses and low AM to PM conversion. The physics of the method and experimental verification are given. The implementation should have a significant impact on TWT performance and increase the channel capacity of communication satellites. Previously announced in STAR as N84-21803

Kosmahl, H. G.↗

Effects of CW interference on the carrier tracking loop of the deep space network

A radio-frequency interference (RFI) environment can cause serious problems for communications systems, such as the Deep Space Network (DSN). For this reason, it is necessary to determine first the RFI susceptibility characteristics for DSN receiving systgms. The present investigation is concerned with CW RFI's which are close in frequency to the carrier frequency. The carrier tracking loop is highly sensitive, and this type of RFI will degrade the carrier loop performance before saturation effects become noticeable. The investigation has the objective to develop an analytical model which will make it possible to predict the tracking performance of the Block IV receiver when operated in the presence of a CW RFI in the receiver passband. The Block IV receiver represents one of the DSN receivers. Attention is given to the effects of a CW RFI on a phase-locked loop, the effects of a bandpass limiter, numerical results, experimental verification, and aspects of computer simulation.

Sue, M. K.↗

Stability of multifrequency negative-resistance oscillators

A general criterion is derived for the stability of a negative-resistance oscillator with respect to small perturbations in the operating point. The derivation applies when the oscillator output consists of an arbitrary number of related frequency components, including possible nonharmonic components. Examples are given of the application of the stability criterion to coaxial IMPATT oscillator circuits, with experimental verification of the frequency and output power at theoretically determined stable operating points.

Bates, B. D.↗

Overview of Aerothermodynamic Loads Definition Study

The Aerothermodynamic Loads Definition were studied to develop methods to more accurately predict the operating environment in the space shuttle main engine (SSME) components. Development of steady and time-dependent, three-dimensional viscous computer codes and experimental verification and engine diagnostic testing are considered. The steady, nonsteady, and transient operating loads are defined to accurately predict powerhead life. Improvements in the structural durability of the SSME turbine drive systems depends on the knowledge of the aerothermodynamic behavior of the flow through the preburner, turbine, turnaround duct, gas manifold, and injector post regions.

Povinelli, L. A.↗

Phase/doppler spray analyzer for simultaneous measurements of drop size and velocity distributions

Research was conducted on a laser light scatter detection method for measuring the size and velocity of spherical particles. The method is based upon the measurement of the interference fringe pattern produced by spheres passing through the intersection of two laser beams. A theoretical analysis of the method was carried out using the geometrical optics theory. The instrument response function was determined to be linear with drop size. Experimental verification of the theory was obtained by using monodisperse droplet streams. Several optical configurations were tested to identify all of the parametric effects upon the size measurements. Both off-axis forward-scatter and back-scatter light detection were utilized. Simulated spray environments and fuel spray nozzles were used in the evaluation of the method. The measurements of the monodisperse drops showed complete agreement with the theoretical predictions. The method was demonstrated to be independent of the beam intensity and extinction resulting from the surrounding drops. An instrument based on the concept has been developed.

Bachalo, W. D.↗

New innovations in composites

Procedures for manufacturing metal clad graphite resin structural elements applicable to optical systems requiring precisely controlled thermal and mechanical properties are described. Analytical estimates were made of the material properties that can be obtained for various ratios of graphite epoxy and aluminum cladding. Three graphite fiber systems were evaluated. Two manufacturing processes are described. One method is a procedure for manufacturing long tubes by wrapping aluminum foil over dry graphite fiber. Resin was applied by spreading before applying the aluminum wrap. A second approach, offering the opportunity for precise tuning of the coefficient of expansion, is by die flattening metal tubing through which a measured amount of fiber has been drawn. Prior to flattening, resin is injected, and after flattening or shaping the part is cured. This latter procedure offers the opportunity to fine tune the structure to achieve a CTE with a precision equal to that of the measuring systems-by modifying the number of fiber tows prior to manufacturing or by etching the metal after manufacturing. Experimental verification and demonstration data are presented for Gr/E bars with aluminum and steel skins.

Bluck, R. M.↗

The absolute amplitude calibration of the SEASAT synthetic aperture radar - An intercomparison with other L-band radar systems

The absolute amplitude calibration of the spaceborne Seasat SAR data set is presented based on previous relative calibration studies. A scale factor making it possible to express the perceived radar brightness of a scene in units of sigma-zero is established. The system components are analyzed for error contribution, and the calibration techniques are introduced for each stage. These include: A/D converter saturation tests; prevention of clipping in the processing step; and converting the digital image into the units of received power. Experimental verification was performed by screening and processing the data of the lava flow surrounding the Pisgah Crater in Southern California, for which previous C-130 airborne scatterometer data were available. The average backscatter difference between the two data sets is estimated to be 2 dB in the brighter, and 4 dB in the dimmer regions. For the SAR a calculated uncertainty of 3 dB is expected.

Held, D.↗