Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Air cargo: An Integrated Systems View. 1978 Summer Faculty Fellowship Program in Engineering Systems Design

The national air cargo system is analyzed and how it should be in 1990 is prescribed in order to operate successfully through 2015; that is through one equipment cycle. Elements of the system which are largely under control of the airlines and the aircraft manufacturers are discussed. The discussion deals with aircraft, networks, facilities, and procedures. The regulations which govern the movement of air freight are considered. The larger public policy interests which must be served by the kind of system proposed, the air cargo integrated system (ACIS), are addressed. The possible social, economical, political, and environment impacts of the system are considered. Recommendations are also given.

Keaton, A.↗
NASA NTRS1984

Engineering and design properties of thallium-doped sodium iodide and selected properties of sodium-doped cesium iodide

Mechanical and thermal properties, not available in the literature but necessary to structural design, using thallium doped sodium iodide and sodium doped cesium iodide were determined to be coefficient of linear thermal expansion, thermal conductivity, thermal shock resistance, heat capacity, elastic constants, ultimate strengths, creep, hardness, susceptibility to subcritical crack growth, and ingot variation of strength. These properties were measured for single and polycrystalline materials at room temperature.

Forrest, K.↗
NASA NTRS1989

Engineering sciences design. Design and implementation of components for a bioregenerative system for growing higher order plants in space

The primary goal was to address specific needs in the design of an integrated system to grow higher plants in space. With the needs defined, the emphasis was placed on the design and fabrication of devices to meet these needs. Specific attention was placed on a hand-held harvester, a nutrient concentration sensor, an air-water separator, and a closed-loop biological system simulation.

Nevill, Gale E., Jr.↗
NASA NTRS1990

Progress in hypersonic combustion technology with computation and experiment

Design of successful airbreathing engines for operation at near-orbital speeds presents significant challenges in all the disciplines involved, including propulsion. This paper presents a discussion of the important physics of hypersonic combustion and an assessment of the state of the art of ground simulations with pulse facilities and with computational techniques. Recent examples of experimental and computational simulations are presented and discussed. The need for continued application of these tools to establish the credibility and fidelity of engineering design methods for practical hypersonic combustors is emphasized along with the critical need for improved diagnostic methods for hypervelocity reacting flows.

Anderson, Griffin Y.↗
NASA NTRS1991

NTR vehicle commonality assessment for piloted lunar and Mars missions

A study is presented that assesses the feasibility of (1) using common nuclear thermal rocket (NTR) vehicle components to perform a wide range of lunar and Mars missions, and (2) potential performance gains achieved via 'dual-mode' NTR operation, where the nuclear reactor is utilized not only for propulsion but also for electrical power generation. Four vehicle configurations are considered, modular designs with multiple single engine modules and single engine designs with multiple propellant tanks. The standard tank sizes arrived at in the Mars mission mass performance calculations are then applied to cargo and piloted lunar craft to evaluate lunar NTR mass performance against that for chemical propulsion.

Collins, John T.↗
NASA NTRS1992

Practical considerations in designing the engine cycle

When it is required to define the cycle parameters and calculate the performance of a real engine, there are numerous practical constraints that need to be taken into account. These fall into two main categories: the limitations of available component technologies, and the operational considerations that are dependent on aircraft application. The lecture discusses the main technology limiters and indicates how they are incorporated into the cycle definition process. Operational factors include the extent of the intended flight envelope and range of critical flight conditions for which performance must be assured, and the balance to be struck between minimising fuel consumption, maximising installed power and constraining costs of ownership. Taking these technology and operational influences into account, the basic cycle characteristics and approach to cycle choice are examined for three main classes of aircraft: subsonic transports, military combat aircraft and helicopters.

M G Philpot↗
NASA NTRS1993

Alternate vehicles for engine/vehicle optimization

The space shuttle main engine, full flow staged combustion, integrated modular engine concept, split expander, and expander bleed rocket engine cycles were studied for use on Single-Stage-to-Orbit fully reusable vehicles. The vehicle uses vertical take-off and horizontal landing and liquid hydrogen rockets for propulsion. The PROPSIZE computer code was modified for use on the available computers. Vehicle sizing was done after trajectory optimization for various engine designs. The various rocket engine cycles were compared and it was found that the full flow staged combustion cycle had the lowest vehicle dry mass. The split expander cycle could have advantages in safety and cooling which could make it the preferred choice in some cases. Comparison to previous work with two-stage heavy-lift vehicles showed that the same ranking of the cycles was found for both vehicle concepts.

Venkatasubramanyam, G.↗
NASA NTRS1995

Perspective on thermal barrier coatings for industrial gas turbine applications

Thermal barrier coatings (TBC's) have been used in high thrust aircraft engines for many years, and have proved to be very effective in providing thermal protection and increasing engine efficiencies. TBC life requirements for aircraft engines are typically less than those required for industrial gas turbines. This paper describes current and future applications of TBC's in industrial gas turbine engines. Early testing and applications of TBC's is reviewed. Areas of concern from the engine designer's and materials engineer's perspective are identified and evaluated. This paper focuses on the key factors that are expected to influence utilization of TBC's in advanced industrial gas turbine engines. It is anticipated that reliable, durable and highly effective coating systems will be produced that will ultimately improve engine efficiency and performance.

Mutasim, Zaher↗
NASA NTRS2003

Solar Thermal Propulsion

This paper presents viewgraphs on Solar Thermal Propulsion (STP). Some of the topics include: 1) Ways to use Solar Energy for Propulsion; 2) Solar (fusion) Energy; 3) Operation in Orbit; 4) Propulsion Concepts; 5) Critical Equations; 6) Power Efficiency; 7) Major STP Projects; 8) Types of STP Engines; 9) Solar Thermal Propulsion Direct Gain Assembly; 10) Specific Impulse; 11) Thrust; 12) Temperature Distribution; 13) Pressure Loss; 14) Transient Startup; 15) Axial Heat Input; 16) Direct Gain Engine Design; 17) Direct Gain Engine Fabrication; 18) Solar Thermal Propulsion Direct Gain Components; 19) Solar Thermal Test Facility; and 20) Checkout Results.

Gerrish, Harold P., Jr.↗
NASA NTRS2005

Multi-Agent Software Design and Engineering for Human Centered Collaborative Autonomous Space Systems: NASA Intelligent Systems

Detailed results of this three-year project are available in 37 publications, including 7 book chapters, 3 journal articles, and 27 refereed conference proceedings. In addition, various aspects of the project were the subject of 31 invited presentations and 6 tutorials at international conferences and workshops. Good descriptions of prior and ongoing work on foundational technologies in Brahms, KAoS, NOMADS, and the PSA project can be found in numerous publications not listed here.

Bradshaw, Jeffrey M.↗
NASA NTRS2010

NASA's Evolutionary Xenon Thruster (NEXT) Prototype Model 1R (PM1R) Ion Thruster and Propellant Management System Wear Test Results

The results of the NEXT wear test are presented. This test was conducted with a 36-cm ion engine (designated PM1R) and an engineering model propellant management system. The thruster operated with beam extraction for a total of 1680 hr and processed 30.5 kg of xenon during the wear test, which included performance testing and some operation with an engineering model power processing unit. A total of 1312 hr was accumulated at full power, 277 hr at low power, and the remainder was at intermediate throttle levels. Overall ion engine performance, which includes thrust, thruster input power, specific impulse, and thrust efficiency, was steady with no indications of performance degradation. The propellant management system performed without incident during the wear test. The ion engine and propellant management system were also inspected following the test with no indication of anomalous hardware degradation from operation.

VanNoord, Jonathan L.↗
NASA NTRS2015

Radiation Engineering for Designers

This tutorial provides an overview of the natural space radiation environment, an introduction to radiation effect types, an overview of EEE parts selection, scrubbing, and radiation mitigation, and an introduction to radiation testing.

radiation effects↗
NASA NTRS2015

Radiation Engineering for Designers

This tutorial provides an overview of the natural space radiation environment, an introduction to radiation effect types, an overview of EEE parts selection, scrubbing, and radiation mitigation, and an introduction to radiation testing.

radiation effects↗
NASA NTRSDate not supplied

Tail-mounted engine Architecture and Design for the Subsonic Single Aft Engine Electrofan Aircraft

This paper describes the turbofan engine architecture for SUbsonic Single Aft eNgine (SUSAN) Electrofan is, a transformative concept hybrid electric aircraft. SUSAN has a single tail-mounted turbofan engine that produces a portion of the requires thrust and drives a 20MW electric generator which in turn provides the power to the 16 electric propulsors located on the wing responsible for producing the remainder of the required thrust. The atypical operation of the turbofan due to the large levels of power extraction from the low pressure turbine (LPT) is described here. This paper investigates the most efficient engine architecture to enable this unique operation, as well as exploring natural gas as an alternative fuel for SUSAN.

EAP↗