Results for “FLOW VELOCITY - DISTRIBUTION” — Page 32

NASA NTRSDate not supplied

Advancing xEMU Lunar Dust Mitigation Devices

Fine, electrically charged, glass like dust particles caused significant damage to the Apollo EMU9 during lunar EVAs, identified as one of the greatest challenges to future exploration. Passive Lunar Dust Mitigation Devices (LDMD) were developed, within a SBIR Phase II, to prohibit this dust from interrupting venting space suit component operation. A Computational Fluid-Dynamics and Discrete Element Method (CFD-DEM) Simulation Tool was developed at the University of Colorado, Boulder to predict venting gas flow ability to self-clean adhered dust particles from LDMD surfaces. Lunar dust properties (i.e., adhesion and cohesion strengths) required to complete Simulation Tool analysis are relatively unknown due to considerable differences between the Earth and the Moon (i.e., gravity, humidity) and due to an absence of dust particles in their native state. Analytically determining gas flow velocity, density and direction within the fluid Boundary Layer, microns from LDMD surfaces presented a second challenge. Dusty Plasma Chamber testing is being performed at Auburn University, Auburn to observe electrostatically charged dust behavior as it adheres to LDMD prototypes and specific geometry and is then blown away by metered gas flow. Test articles were developed to offer insight into the impact of different flow geometries, surface roughness and dust removal within the gas Boundary-Layer. Observed dust behavior is currently being developed to support the CFD-DEM analysis. Many Simulation Tool analytical cases have been processed to support the intention of completing sensitivity studies to assess how different dust adherence values and Boundary Layer fluid properties impact LDMD self-cleaning effectivity.

Thomas J Stapleton↗

NASA NTRS1993

On the combustion of a laminar spray

A spray combustor, with flow velocities in the laminar range, exhibits a unique operating mode where large amplitude, self-induced oscillations of the flame shape occur. The phenomenon, not previously encountered, only occurs when fuel is supplied in the form of fine liquid droplets and does not occur when fuel is supplied in gaseous form. Several flow mechanisms are coupled in such a fashion as to trigger and maintain the oscillatory motion of the flame. These mechanisms include heat transfer and evaporation processes, dynamics of two-phase flows, and effects of gravity (buoyancy forces). An interface volume, lying above the fuel nozzle and below the flame was found to be the most susceptible to gravity effects and postulated to be responsible for inducing the oscillatory motion. Heptane fuel was used in the majority of the tests. Tests performed with iso-octane also showed similar results.

Levy, Yeshayahou↗

NASA NTRS1995

On the Oscillation of Combustion of a Laminar Spray

A spray combustor, with flow velocities in the laminar range, exhibits a unique operating mode where large amplitude, self-induced oscillations of the flame shape occur. The phenomenon, not previously encountered, only occurs when fuel is supplied in the form of fine liquid droplets and does not occur when fuel is supplied in gaseous form. Several flow mechanisms are coupled in such a fashion as to trigger and maintain the oscillatory motion of the flame. These mechanisms include heat transfer and evaporation processes, dynamics of two-phase flows, and effects of gravity (buoyancy forces). An interface volume, lying between the fuel nozzle and the flame was found to be the most susceptible to gravity effects, and postulated to be responsible for inducing the oscillatory motion. Heptane fuel was used in the majority of the tests.

Levy, Yeshayahou↗

DOE OSTI2026

A Scalable Reduced‐Order Model for the Steady Navier–Stokes Equations

Scaling up new scientific technologies from laboratory to industry often involves demonstrating performance on a larger scale. Computer simulations can accelerate design and predictions in the deployment process, though traditional numerical methods are computationally intractable even for intermediate pilot plant scales. Recently, the component reduced order modeling method has been developed to tackle this challenge by combining projection reduced order modeling and discontinuous Galerkin domain decomposition. However, while many scientific or engineering applications involve nonlinear physics, this method has only been demonstrated for various linear systems. In this work, the component reduced order modeling method is extended to steady Navier–Stokes flow, with application to general nonlinear physics in view. The large‐scale, global domain is decomposed into a combination of small‐scale unit component. Linear subspaces for flow velocity and pressure are identified via proper orthogonal decomposition over sample snapshots collected from each small‐scale unit component. Velocity bases are augmented with a pressure supremizer to satisfy the inf–sup condition for stable pressure prediction. Two different nonlinear reduced order modeling methods are employed and compared for efficient evaluation of nonlinear advection: A third‐order tensor projection operator and the empirical quadrature procedure. The proposed method is demonstrated on the flow over arrays of five different unit objects, achieving a 23‐fold speedup with less than 4% relative error in domains up to 256 times larger than the unit components. Furthermore, a numerical experiment with the pressure supremizer strongly indicates the need for a supremizer for stable pressure prediction. A comparison between the tensorial approach and the empirical quadrature procedure revealed a slight advantage of the empirical quadrature procedure. The framework is compared with an alternating Schwarz‐based reduced‐order approach, demonstrating improved efficiency and robustness for the DG‐based global solver while retaining flexibility for sub‐scale iterative solvers. The method is further extended to a coupled advection–diffusion and Navier–Stokes system, illustrating its applicability to multi‐physics problems and its potential for more general, inter‐coupled nonlinear systems.

42 ENGINEERING↗

NASA NTRS1990

Experimental measurements of the laminar separation bubble on an Eppler 387 airfoil at low Reynolds numbers

An experimental investigation was conducted to measure the flow velocity in the boundary layer of an Eppler 387 airfoil. In particular, the laminar separation bubble that this airfoil exhibits at low Reynolds numbers was the focus. Single component laser Doppler velocimetry data were obtained at a Reynolds number of 100,000 at an angle of attack of 2.0 degree. Static Pressure and flow visualization data for the Eppler 387 airfoil were also obtained. The difficulty in obtaining accurate experimental measurements at low Reynolds numbers is addressed. Laser Doppler velocimetry boundary layer data for the NACA 663-018 airfoil at a Reynolds number of 160,000 and angle of attack of 12 degree is also presented.

Cole, Gregory M.↗

NASA NTRS1993

Opposed-Flow Flame Spreading in Reduced Gravity

Experimental results obtained in drop towers and in Space Shuttle based experiments coupled with modelling efforts are beginning to provide information that is allowing an understanding to be developed of the physics of opposed-flow flame spread at reduced gravity where the spread rate and flow velocity are comparable and of the role played by radiative and diffusive processes in flame spreading in microgravity. Here we describe one Space Shuttle based experiment on flame spreading in a quiescent environment, the Solid Surface Combustion Experiment, SSCE, one planned microgravity experiment on flame spreading in a radiatively-controlled, forced opposing flow environment, the Diffusive and Radiative Transport in Fires Experiment, DARTFire, modelling efforts to support these experiments, and some results obtained to date.

Altenkirch, Robert A.↗

DOE OSTI2021

Probing early-time longitudinal dynamics with the Λ hyperon's spin polarization in relativistic heavy-ion collisions

Here, we systematically study the hyperon global polarization's sensitivity to the collision systems' initial longitudinal flow velocity in hydrodynamic simulations. By explicitly imposing local energy-momentum conservation when mapping the initial collision geometry to macroscopic hydrodynamic fields, we study the evolution of systems' orbital angular momentum (OAM) and fluid vorticity. We find that a simultaneous description of the $\Lambda$ hyperons' global polarization and the slope of pion's directed flow can strongly constrain the size of longitudinal flow at the beginning of hydrodynamic evolution. We extract the size of the initial longitudinal flow and the fraction of orbital angular momentum in the produced QGP fluid as a function of collision energy with the STAR measurements in the RHIC Beam Energy Scan program. We find that there is about 100-200 $\hbar$ OAM that remains in the mid-rapidity fluid at the beginning of hydrodynamic evolution. We further exam the effects of different hydrodynamic gradients on the spin polarization of $\Lambda$ and $\bar{\Lambda}$. The gradients of $\mu_B/T$ can change the ordering between $\Lambda$'s and $\bar{\Lambda}$'s polarization.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS1980

Light ion concentrations and fluxes in the polar regions during magnetically quiet times

Ion concentrations, flow velocities, and fluxes, measured by the ion mass spectrometer on the Isis 2 satellite for periods around the solstices and equinoxes of 1971 and 1972, have been used in a study of the polar wind morphology during magnetically quiet times. The results confirm the major tenets of polar wind theories; namely, that an upward flow of both H(+) and He(+) ions exists at all times over the entire polar region; H(+) fluxes are of the order of 10 to the 8th ions/sq cm s in both summer and winter polar regions. O(+) is the dominant ion specie at 1400-km altitude in regions of strong H(+) flows, and H(+) is depleted over the entire region where the polar wind flows. H(+) fluxes tend to be lower in winter than in summer, whereas He(+) fluxes are a factor of 10 higher in winter and tend to follow the neutral helium concentration near the F2 maximum. The latter agree well with model calculations of flux in the winter but lie above the model values by a factor of 2 in the summer. H(+) fluxes also agree well with ion flow models.

Hoffman, J. H.↗

NASA NTRS1985

Use of two-phase flow heat transfer method in spacecraft thermal system

In space applications, weight, volume and power are critical parameters. Presently liquid freon is used in the radiator planels of the Space Shuttle to dissipate heat. This requires a large amount of freon, large power for pumps, large volume and weight. Use of two-phase flow method to transfer heat can reduce them significantly. A modified commercial vapor compression refrigerator/freezer was sucessfully flown in STS-4 to study the effect of zero-gravity on the system. The duty cycle was about 5 percent higher in flight as compared to that on earth due to low flow velocity in condenser. The vapor Reynolds number at exit was about 4000 as compared to about 12,000. Efforts are underway to design a refrigerator/freezer using an oil-free compressor for Spacelab Mission 4 scheduled to fly in January 1986. A thermal system can be designed for spacecraft using the two-phase flow to transfer heat economically.

Hye, A.↗

NASA NTRS2001

Low Stretch PMMA Burning in Microgravity: Status of the Ground-Based Program and New ISS Glovebox Experiment SALSA

The objective of this ground-based program is to study low stretch diffusion flames burning PMMA as the solid fuel to determine the relationship between buoyant low stretch burning in normal gravity and forced flow low stretch burning in microgravity. The low stretch is generated in normal gravity by using the buoyant convection induced by burning the bottom of a large radius of curvature sample. Low stretch is also generated using the Combustion Tunnel drop tower rig (2.2 and 5.2 second facilities), which provides a forced convective low velocity flow past smaller radius of curvature samples. Lastly, an ISS glovebox investigation is being developed to study low stretch burning of PMMA spheres to obtain long duration testing needed to accurately assess the flammability and burning characteristics of the material in microgravity. A comparison of microgravity experiment results with normal gravity test results allows us to establish a direct link between a material's burning characteristics in normal gravity (easily measured) with its burning characteristics in extraterrestrial environments, including microgravity forced convective environments. Theoretical predictions and recent experimental results indicate that it should be possible to understand a material's burning characteristics in the low stretch environment of spacecraft (non-buoyant air movement induced by fans and crew disturbances) by understanding its burning characteristics in an equivalent Earth-based low stretch environment (induced by normal gravity buoyancy). Similarly, Earth-based stretch environments can be made equivalent to those in Lunar- and Martian-surface stretch environments (which would induce partial-gravity buoyancy).

Olson, S. L.↗

NASA NTRS2004

Magnetic and Langmuir Probe Measurements on the Plasmoid Thruster Experiment (PTX)

The Plasmoid Thruster Experiment (PTX) operates by inductively producing plasmoids in a conical theta-pinch coil and subsequently ejecting them at high velocity. An overview of PTX is described in a companion paper. The shape and magnetic field structure of the translating plasmoids will be measured with of an array of inductive magnetic field probes. Six sets of two B-dot probes (for a total of twelve probes) have been constructed for measuring B(sub z) and B(sub theta), the axial and azimuthal components of the magnetic field. The probes were calibrated with a Helmholtz coil, driven alternately by a high-voltage pulser or a signal generator. The probes are wound on a G-10 form, and have an average (calibrated) NA of 9.37 x 10(exp -5) square meters, where N is the number of turns and A is cross-sectional area. The frequency response of the probes was measured over the range from 1 kHz to 10 MHZ. The electron number density n(sub e), electron temperature T(sub e) and velocity v will be determined from measurements taken with a quadruple Langmuir probe, situated in the exhaust chamber. Three of the four probes on the quadruple probe sample the current-voltage characteristic, and from this yield measurements of T(sub e) and n(sub e). The fourth probe provides a measurement of plasma flow velocity. A 6-inch long alumina rod, hollowed with four holes to house the probe wires, is being used to construct the quadruple probe. A variety of propellants will be used, including hydrogen, nitrogen and argon. From the measurements of the plasmoid mass, density, temperature, and velocity, the basic propulsion characteristics of PTX will be evaluated.

Koelfgen, Syri J.↗

DOE OSTI2020

Geometric Scale-up Experiments on Fluidization of Geldart B Glass Beads

The objective of this work is to provide a valuable database from controlled experiments for validating computational models. Recently, coarse-grained techniques such as particle-in-cell (PIC) or coarse-grained discrete element modeling (DEM) have gained popularity due to their computational efficiency while modeling large-scale systems; however, the influence of model parameters and their sensitivities at different geometric scales and flow conditions remain to be analyzed. These datasets are critical for the multiphase flow research community to assess predictive capability of modeling techniques as well as elucidate the hydrodynamic behavior in these systems. This study performed fluidization experiments using three different test sections with internal diameters of 2.5, 4, and 6 in. The operating conditions, bed material, and range of flow velocities at the inlet were constant in all the units, which were not hydrodynamically scaled. Glass beads having a Sauter Mean Diameter of 332 μm were used. Superficial velocity was varied from 2.97 to 5.35 times the minimum fluidization velocity and the initial static bed height was 0.1524 m. The order in which the experiments were performed was randomized and replicates were included to provide uncertainty in measurements. Statistics of differential pressure and bed height from these tests were reported. Future plans include validating PIC methodology in the open-source software, MFiX (Multiphase Flow with Interphase Exchanges) using results from this study. This could further be extended to determine optimal model parameters using inverse techniques such as deterministic calibration or Bayesian inference.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2020

Geometric Scale-up Experiments on Fluidization of Geldart B Glass Beads

The objective of this work is to provide a valuable database from controlled experiments for validating computational models. Recently, coarse-grained techniques such as particle-in-cell (PIC) or coarse-grained discrete element modeling (DEM) have gained popularity due to their computational efficiency while modeling large-scale systems; however, the influence of model parameters and their sensitivities at different geometric scales and flow conditions remain to be analyzed. These datasets are critical for the multiphase flow research community to assess predictive capability of modeling techniques as well as elucidate the hydrodynamic behavior in these systems. This study performed fluidization experiments using three different test sections with internal diameters of 2.5, 4, and 6 in. The operating conditions, bed material, and range of flow velocities at the inlet were constant in all the units, which were not hydrodynamically scaled. Glass beads having a Sauter Mean Diameter of 332 μm were used. Superficial velocity was varied from 2.97 to 5.35 times the minimum fluidization velocity and the initial static bed height was 0.1524 m. The order in which the experiments were performed was randomized and replicates were included to provide uncertainty in measurements. Statistics of differential pressure and bed height from these tests were reported. Future plans include validating PIC methodology in the open-source software, MFiX (Multiphase Flow with Interphase Exchanges) using results from this study. This could further be extended to determine optimal model parameters using inverse techniques such as deterministic calibration or Bayesian inference.

42 ENGINEERING↗

NASA NTRS1985

A stagnation pressure probe for droplet-laden air flow

It is often of interest in a droplet-laden gas flow to obtain the stagnation pressure of both the gas phase and the mixture. A flow-decelerating probe (TPF), with separate, purged ports for the gas phase and the mixture and with a bleed for accumulating liquid at the closed end, has been developed. Measurements obtained utilizing the TPF in a nearly isothermal air-water droplet mixture flow in a smooth circular pipe under various conditions of flow velocity, pressure, liquid concentration and droplet size are presented and compared with data obtained under identical conditions with a conventional, gas phase stagnation pressure probe (CSP). The data obtained with the CSP and TPF probes are analyzed to determine the applicability of the two probes in relation to the multi-phase characteristics of the flow and the geometry of the probe.

Murthy, S. N. B.↗

NASA NTRSDate not supplied

Particle Seeding Method for Small-Scale, High-Pressure Nozzles

NASA tests new launch and reentry vehicle configurations in wind tunnels, where flow visualizations and quantitative flowfield measurements are often desired. Some of these vehicles have rocket motors for propulsion, retro-propulsion, or reaction control. High-pressure air is used to supply these rocket motor plumes. However, it is difficult to make off-body measurements in these regions, for several reasons. First, the plumes themselves lack seeding particles for flow diagnostics, and at the low pressures after expansion, Rayleigh scattering or other molecular techniques yield insufficient signal for flow velocity measurements. Second, the plumes displace particle-seeded tunnel air, preventing measurements in the vicinity of the plume. Third, the plumes force shock waves ahead of the vehicle, which melts the ice crystal fog commonly used for visualization and measurement techniques in certain facilities. In the current work, a novel method for seeding the flow in these small-scale, high-pressure nozzles has been devised and initially demonstrated, potentially enabling quantitative and qualitative measurements with particle-based instruments such as Doppler global velocimetry or particle image velocimetry. The method involves a Venturi contraction to draw the seed liquid out of a reservoir and into the nozzle channel, wherein shearing forces atomize the seed into particles. The concept was tested with a laser sheet visualization, which demonstrated that the flow rate of liquid spray was controllable; a valve could be adjusted to drop the flow rate by up to 65%. This relatively inexpensive and simple technique may prove useful in wind tunnel experiments involving particle-based laser diagnostics and small, high-pressure nozzles.

Aditya S. Acharya↗

NASA NTRSDate not supplied

Particle Seeding Method for Small-Scale, High-Pressure Nozzles

NASA tests new launch and reentry vehicle configurations in wind tunnels, where flow visualizations and quantitative flowfield measurements are often desired. Some of these vehicles have rocket motors for propulsion, retro-propulsion, or reaction control. High-pressure air is used to supply these rocket motor plumes. However, it is difficult to make off-body measurements in these regions, for several reasons. First, the plumes themselves lack seeding particles for flow diagnostics, and at the low pressures after expansion, Rayleigh scattering or other molecular techniques yield insufficient signal for flow velocity measurements. Second, the plumes displace particle-seeded tunnel air, preventing measurements in the vicinity of the plume. Third, the plumes force shock waves ahead of the vehicle, which melts the ice crystal fog commonly used for visualization and measurement techniques in certain facilities. In the current work, a novel method for seeding the flow in these small-scale, high-pressure nozzles has been devised and initially demonstrated, potentially enabling quantitative and qualitative measurements with particle-based instruments such as Doppler global velocimetry or particle image velocimetry. The method involves a Venturi contraction to draw the seed liquid out of a reservoir and into the nozzle channel, wherein shearing forces atomize the seed into particles. The concept was tested with a laser sheet visualization, which demonstrated that the flow rate of liquid spray was controllable; a valve could be adjusted to drop the flow rate by up to 65%. This relatively inexpensive and simple technique may prove useful in wind tunnel experiments involving particle-based laser diagnostics and small, high-pressure nozzles.

lasers↗

DOE OSTI2024

Relative permeabilities for two-phase flow through wellbore cement fractures

Multiple fluids are likely to exist in fractures and flow paths associated with leaky wellbores, including liquids (e.g., crude oil) and gases (e.g., gas exsolved from liquid). These fluids occupy and move through different portions of the pore spaces within the fractures depending on many factors, including fluid properties, fracture size, and the amount of the different fluids. Upward leakage of any phase, through the fracture, can contaminate water-bearing formations, create hazardous surface conditions, and compromise the functionality of the wellbore. Early signs of wellbore leaks may be expressed by anomalous pressure behavior at surface monitoring points on cavern storage wells. These pressure anomalies are difficult to interpret, necessitating knowledge of the factors that affect the multiphase flow in fractures and porous media. These parameters are critical to modeling multiphase flow in fractures. This insight can guide further diagnosis and maximize leak remediation. Here, our study focuses on the relationship of the liquid–gas relative permeabilities for representative variable-aperture wellbore cement fracture. To obtain the relative permeability of each phase, two-phase flow tests were conducted where both fluids were flowing simultaneously through a fractured wellbore cement specimen under a range of factors, namely (1) aperture size, (2) capillary numbers, and (3) viscosity ratio. The flow experiments were conducted under a range of confining stresses and flow velocities, using nitrogen gas and silicone oils (of different viscosities) in a specially designed pressure vessel. The sum of gas and oil relative permeabilities were found to be less than one under all conditions, which indicates that the presence of one phase affects the permeability of the other phase, and vice versa. Since the gas phase flow conditions include a significant inertial flow component in addition to viscous flow, the inertial flow coefficients at different saturation states are presented. The factors affecting the relationship between the relative permeabilities are discussed in detail. A new mathematical model for estimating the relative permeability of wellbore cement fracture is presented and experimentally validated.

58 GEOSCIENCES↗

DOE OSTI2022

A time‐varying formulation of the curled wake model within the FAST.Farm framework

Abstract In this article, we present a time‐varying formulation of the curled wake model that we implemented in FAST.Farm. The curled wake model, originally developed for steady‐state conditions, is used to produce realistic wake profiles behind a wind turbine in yawed (or skewed) conditions. We begin by introducing the key elements of the FAST.Farm framework. Then, after briefly summarizing the original wake dynamics formulation of FAST.Farm based on a polar wake profile, we present the new time‐varying formulation of the curled wake model, compare the two, and highlight the differences with the original curled wake model. After discussing some implementation details, we present different applications with increasing levels of complexity: single turbine with uniform and turbulent inflow, fixed and transient yaw, and multiple turbines. We verify our results using the original FAST.Farm implementation and large‐eddy simulations. The results with the new curled wake model are improved compared to the original implementation, as they include cross‐flow velocities and wake asymmetry. Yet, large‐eddy simulation results show a more pronounced lateral convection of the wake and a stronger concentration of vorticity at the top vortex. The new curled wake implementation in FAST.Farm should enable the calculation of not only generator power but also wind turbine structural loads for applications involving intentional or unintentional skewed flow and wind‐farm control involving wake steering.

17 WIND ENERGY↗