Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Oxidation and Associated Pore Structure Modification During Experimental Alteration of Granite

Weathering plays a crucial role in a number of environmental processes, and the microstructure and evolution of multi-scale pore space is a critically important factor in the weathering of geological formations. In igneous rocks the infiltration of meteoric water into initially relatively dry material can cause the rock to begin to disaggregate, increasing porosity and surface area, and allowing further disaggregation and weathering to occur. These processes, in turn, allow biota to colonize the rock, further enhancing the weathering rate. In some igneous rocks this may be driven by oxidation of primary minerals. One such mineral, biotite, has been repeatedly mentioned as a cause of cracking during oxidation. However, the scale-dependence of the processes by which this occurs are poorly understood. We cannot, therefore, accurately extrapolate laboratory reaction rates to the field in predictive numerical models. In order to better understand the effects of oxidation and test the hypothesis that fracture and disaggregation are initiated by swelling of oxidizing biotites, we reacted granite cores in a selenic acid-rich aqueous solution at 200°C for up to 438 days. Elevated temperatures and selenic acid were used to provide relatively fast reaction rates and highly oxidizing conditions in sealed reaction vessels. These experiments were analyzed using a combination of imaging, X-ray diffraction, Mössbauer spectroscopy, and small- and ultra-small angle neutron scattering to interrogate porosity and microfracture formation. The experimental results show little observable biotite swelling, but significant transport and growth of iron oxides and/or clays along grain boundaries throughout the sample. Significant increases in porosity were also observed at the sample rim, likely associated with feldspar alteration. Fractures and transport were observed throughout the core, suggesting that stresses due to crystallization pressures caused by the growing iron phases may be the initiating factors in granite weathering, possibly followed by biotite swelling after sufficient permeability is achieved.

Anovitz, Lawrence M.↗

Influence of rapid heating and cooling combined with deformation at ultrahigh strain rates on the microstructure evolution of pure titanium shaped charge liner

Highlights: • A slug prepared from pure titanium SCL was recovered after detonation deformation at an ultrahigh strain rate over 10{sup 5} s{sup −1}. • The α → β → α phase transformation occurred in Ti SCL during the ultrahigh-strain -rate deformation. • The microstructures of the recovered slug included lamellar α grains, equiaxed α grains, and jagged α grains. - Abstract: A slug prepared from pure titanium shaped charge liners was recovered after detonation deformation at an ultrahigh strain rate over 10{sup 5} s{sup −1} and high strain over 500%. Optical microscopy, electron backscattered diffraction (EBSD), and transmission electron microscopy (TEM) were employed to investigate the microstructure of the Ti shaped charged liner before and after the detonation deformation. The microstructures of the recovered slug include lamellar α grains, equiaxed α grains within localized shear bands, and jagged α grains. EBSD results indicated that the grain orientation distribution is random and no texture was observed in the slug. TEM observation revealed that the α → β → α phase transformation occurred owing to the rapid heating and cooling combined with deformation at ultrahigh strain rates in the Ti shaped charge liner. No melting phenomenon was observed during the deformation process. The deformation process consisted of the explosive detonation stage combined with rapid heating and the subsequent penetration stage combined with rapid cooling. In the explosive detonation stage, the α → β phase transformation instantaneously occurred via a martensitic mechanism. In the penetration stage, the high-temperature slug in β state was cooled rapidly and showed different deformation behaviors in three different areas.

36 MATERIALS SCIENCE↗

Fracture modes in tubular LSFCO ceramic membranes under graded reducing conditions

Highlights: ► Microstructural evolution in LSFCO membranes under graded environment is reported. ► The role of chemically induced stresses and oxygen deficiency is evaluated. ► The stress distribution is modeled by a point defect model. - Abstract: Chromium (III) oxide (Cr{sub 2}O{sub 3})-doped LaSrFeO{sub 3} perovskite, La{sub 0.2}Sr{sub 0.8}Fe{sub 0.8}Cr{sub 0.2}O{sub 3−δ} (LSFCO), is being considered as a potential material for applications in solid oxide fuel cells, gas separation membranes, and electrochemical reactors because of its high electro-catalytic activity. Similar to other perovskites, the performance and mechanical strength of LSFCO materials are significantly affected by environment and temperature. Here, we report a fracture gradient phenomenon in tubular C-ring-shaped LSFCO ceramic membranes under graded reducing conditions. The graded reducing condition was produced by flushing N{sub 2} on the outer side of the C-ring membranes at 1000 °C while keeping the inner side untreated. The rings were then diametrically compressed to fracture, and the resultant fracture morphology was analyzed with a scanning electron microscope (SEM). A fracture gradient with three distinct regions across the thickness of the membranes was identified on the split surfaces. In the outer region of the C-ring specimen exposed to N{sub 2}, a mixed inter/transgranular fracture with a predominant intergranular pattern was observed. In the middle section of the fracture surface, a characteristic transgranular fracture of the perovskite grains was found. At the inner region of the ring, a mixed inter/transgranular fracture with a predominant transgranular pattern occurred. The mechanism of gradient fractures was attributed both to chemically induced stresses caused by oxygen diffusion and to the formation of a separate phase of oxygen-deficient perovskite in the parent perovskite. The stresses generated were modeled by a point defect model. This work provides significant information on microstructure evolutions of tubular LSFCO membranes under graded reducing atmospheres.

36 MATERIALS SCIENCE↗

Twinning behaviors of a rolled AZ31 magnesium alloy under multidirectional loading

The microstructure and texture evolution of an AZ31 magnesium rolled sheet during quasi-static compression at strain rates of 10{sup −3} s{sup −1} has been investigated by in situ electron backscattered diffraction. The influence of the initial and pre-deformed texture on the predominant deformation mechanisms during compression has been examined. It has been found that extensive grain reorientation due to (10 − 12) tensile twinning appeared when compressed along transverse direction. Tensile twin variants were observed under this loading condition, and different variants will cause an effect to the following deformation. Several twinning modes occurred with continuative loading along rolling direction. - Highlights: •Twinning behaviors were investigated through in situ multidirectional compressive tests. •Deformation behavior was affected by the twin variants. •Four types of twinning behaviors were observed during deformation process.

36 MATERIALS SCIENCE↗

Microstructure Validation of Graph Theory Model-Derived Cooling Rates in the Wire Arc Additive Manufacturing of ER70S-6 Steel

Wire arc additive manufacturing (WAAM) enables high-rate fabrication of large metallic components, but spatial variations in thermal history can lead to microstructural heterogeneity that requires efficient process models to evaluate. This study evaluates whether cooling rates extracted from a graph theory model (GTM)-based thermal simulation are consistent with the microstructural evolution observed in an ER70S-6 WAAM wall. Thermal histories from the model were analyzed at selected build heights, and cooling rates were extracted from the final thermal excursion through the austenite phase field. Microstructures at corresponding locations were characterized using electron backscatter diffraction (EBSD) to quantify grain size distributions, and pearlite interlamellar spacing was used as an additional indicator of cooling behavior. The modeled cooling rates were highest near the substrate and generally decreased with build height, consistent with the observed reduction in the fine grain fraction and the progressive shift in the grain size distribution as build height increased. Pearlite spacing trends also supported the modeled cooling rate variation. These results indicate that GTM-derived thermal histories can be post-processed into metallurgically meaningful cooling rate estimates for WAAM steel builds and linked to dataset specific empirical grain size distribution relationships for process–thermal history–microstructure assessment.

36 MATERIALS SCIENCE↗

Sensitivity of UO 2 fuel performance to microstructural evolutions driven by dilute additives

Use of dilute additives to nuclear fuel is being considered to increase the security of commercial fuel management through traceability of fabricated fuel elements. Taggants, as additives are denoted when included for traceability purposes, may also improve fuel performance, as demonstrated in Cr-containing uranium dioxide as described in the literature, and they may also improve fuel safety. In fact, studies have shown that some additives affect fuel material properties such as grain size and density after sintering. Given the possible range of elements that could be used as additives, the impact of such fuel property variations on the fuel’s thermomechanical behavior becomes relevant. These effects can be evaluated through a sensitivity study of standard fuel models to analyze changes in these properties using a fuel performance code. In this work, the BISON code is being used to investigate these effects through a 2D axisymmetric model of smeared UO 2 fuel pellets and ZIRLO® cladding under realistic pressurized water reactor core irradiation conditions. Here, randomly sampled densities and grain sizes within specified ranges are used as input parameters in the simulations, and several fuel model-related outputs are evaluated. The thermomechanical response of the cladding is also addressed in this study. The simultaneous variation of both input parameters offers a more comprehensive path to identify key sensitivities. Outputs explored include temperature, fission gas release, creep, and radial stress. Results show that although most of these outputs are sensitive to grain size to a certain extent, density mainly affects fuel temperature and elastic strain. Furthermore, sensitivities can vary depending on the radial position within the fuel pellet.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Using machine-learning to understand complex microstructural effects on the mechanical behavior of Ti-6Al-4V alloys

Structural materials properties are highly dependent on their microstructure. Their microstructure is in turn affected by multiple fabrication and thermo-mechanical treatment parameters, all of which conform a highly-dimensional parametric space with often hidden correlations that are difficult to extract by experimentation alone. This is particularly true for alloys of the dual-phase Ti-6Al-4V family, with their greatly complex and rich microstructures, which combine several intrinsic length scales associated with multiple grain and subgrain structures, grains with different crystal lattices (α and β phases), and complex chemistry. In this paper we use a comprehensive set of machine learning techniques to develop predictive tools relating the yield strength and hardening rate of these alloys to a set of input parameters covering extensive ranges. The data generator is a finite-element crystal plasticity model for polycrystal deformation that takes into account slip anisotropy and employs standard dislocation evolution models for the α and β phases of Ti-based alloys. Our dataset includes over two thousand independent simulations and is used to train the machine learning models, which are then used to establish correlations between microstructural parameters and the alloys’ mechanical response. Our results point to the most influential parameters affecting yield strength and hardening rate, information that can then be used to guide experimental synthesis and characterization efforts to save time and resources.

36 MATERIALS SCIENCE↗

Development of microstructure and texture during single and multiple pass friction stir processing of a strain hardenable aluminium alloy

Highlights: • Development of microstructure and texture during single and multiple pass FSP of a strain hardenable aluminium alloy • Strain induced boundary migration (SIBM) is the dominant nucleation mechanism for recrystallization • Weak crystallographic texture development influenced by SIBM with the relative dominance of shear texture components • Stable microstructure and texture development after multiple pass FSP • FSP is a promising method for the secondary processing of strain hardenable aluminium alloys - Abstract: In the present study, microstructure and texture development during single and multiple pass friction stir processing (FSP) of a strain hardenable wrought AlMg alloy (AA5086) was investigated. Subtle differences were observed while comparing with heat treatable alloys in the nucleation mechanism of the recrystallized microstructure observed in the nugget zone. Strain induced boundary migration was the dominant mechanism of microstructure evolution in the alloy, which influenced the crystallographic texture development by weakening it. Micro-texture measurements reveal variations in the crystallographic texture along the thickness of the sample. Recrystallization texture components were observed in the nugget zone indicative of a pronounced static recrystallization in the alloy as compared to the heat treatable alloys. Bulk texture measurements within the nugget zone of the optimally processed sample reveal a relatively dominant C component of shear texture. Average grain size in the nugget zone remained the same and the bulk crystallographic texture components were retained during multiple-pass FSP. The lower strain energies involved and the enhanced recovery processes due to the high temperature materials processing of the alloy during FSP resulted in a stable microstructure and texture. In summary, FSP could be promoted as a competent and suitable secondary processing technique for the bulk production of ultra-fine-grained materials in strain hardenable aluminium alloys.

36 MATERIALS SCIENCE↗

Influence of scan pattern and geometry on the microstructure and soft-magnetic performance of additively manufactured Fe-Si

The influence of geometry and scan pattern on the microstructure evolution and magnetic performance of additively manufactured Fe-3Si components was investigated. To reduce eddy current losses, novel geometries were designed and built and the microstructure and properties of these samples were characterized. The laser scan pattern was shown to strongly influence both the as-built grain structure and strength of the crystallographic texture, resulting in measurable changes in the as-built magnetic performance. In thin wall samples, heat treatment resulted in an increase in the maximum relative magnetic permeability and decrease in power losses in most samples, consistent with grain growth. However, decreases in the spacing between thin walls to increase the stacking factor of the cross-section was shown to result in unwanted electrical shorting between walls and an increase in eddy current losses. Compared to simple parallel plate construction and a mesh structure, a novel cross-section design based on the Hilbert space filling curve was found to produce the lowest power losses. The mechanisms behind these results were explored using a combination of heat conduction and electromagnetic simulations, providing a route for future component and process optimization.

36 MATERIALS SCIENCE↗

Investigation of the Use of Laser Shock Peening for Enhancing Fatigue and Stress Corrosion Cracking Resistance of Nuclear Energy Materials

The objective of this project, which includes close collaboration with scientists from INL and ANL, is to investigate and demonstrate the use of advanced mechanical surface treatments like laser shock peening (LSP) and ultrasonic nanocrystal surface modification (UNSM) and establish baseline parameters for enhancing the fatigue properties and SCC resistance of nuclear materials like nickel-based alloy 600 and 304 stainless steel. The research program includes the following key elements/tasks: 1) Procurement of Alloy 600 and 304 SS, heat treatment studies; 2) LSP and UNSM processing of base metal and welds/HAZ of alloys 600 and 304; (3) measurement and mapping of surface and sub-surface residual strains/stresses and microstructural changes as a function of process parameters using novel methods; (4) determination of thermal relaxation of residual stresses (macro and micro) and microstructure evolution with time at high temperatures typical of service conditions and modeling of the kinetics of relaxation; (5) evaluation of the effects of residual stress, near surface microstructure and temperature on SCC and fatigue resistance and associated microstructural mechanisms; and (6) studies of the effects of bulk and surface grain boundary engineering on improvements in the SCC resistance and associated microstructural and cracking mechanisms

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Type IV failure in weldment of creep resistant ferritic alloys: I. Micromechanical origin of creep strain localization in the heat affected zone

Creep strength enhanced ferritic (CSEF) steels containing 9-12wt% chromium have been extensively used in fossil-fuel-fired power plants. Despite their excellent creep resistance at high temperatures, premature failures (especially Type IV cracking) are often found in the fine-grained heat affected zone (HAZ) or intercritical HAZ of the welded components. This failure mode is preceded by the strain localization in the HAZ, as measured by the Digital Image Correlation (DIC) technique. The present work aims to develop a finite-element based computational method to determine the micromechanical and microstructural origin of the strain localization phenomenon. We construct a two-dimensional digital microstructure based on the actual microstructure of ferritic steel weldments by using the Voronoi-tessellation method, to account for the effects of its large grain-size gradients. A mechanism-based finite element method is developed for modeling the high temperature deformation resulting from a synergy of thermally activated dislocation movements, diffusional flow and grain boundary sliding. The numerical results agree well with the strain measurements by our DIC technique, particularly revealing the effect of pre-welding tempering on the evolution of strain localization in HAZ of creep resistant steel weldments. It is found that the diffusional creep with dependence on grain sizes, dislocation creep with dependence on material strength, and more importantly, grain boundary sliding, contribute synergistically to the creep strain accumulation in the HAZ, and their relative degree of significance is quantified. The creep rupture life will be investigated in the companion paper.

36 MATERIALS SCIENCE↗

Microstructural Evolution and the Precipitation Behavior in X90 Linepipe Steel During Isothermal Processing

Thermomechanical controlled processing of 560-MPa (X90) linepipe steel was simulated in the laboratory using a thermomechanical simulator to study the microstructural evolution and precipitation behavior during isothermal holding. The results indicated that martensite was obtained when the steels were isothermally held for 5 s at 700 °C. Subsequently, granular bainite and acicular ferrite transformation occurred with increased holding time. Different amount of polygonal ferrite formed after isothermally holding for 600-3600 s. Pearlite nucleated after isothermally holding for 3600 s. Precipitation occurred after isothermal holding for 5 s and continuous precipitation occurred at grain boundaries after isothermally holding for 600 s. After isothermally holding for 3600 s, large Nb/Ti carbide precipitated. The presence of MX-type precipitates was confirmed by diffraction pattern. The interphase precipitation (IP) occurred between 5 and 30 s. Maximum hardness was obtained after isothermally holding for 600 s when IP occurred and rapidly decreased to a low value, mainly because polygonal ferrite dominated the microstructure after isothermally holding for 3600 s.

36 MATERIALS SCIENCE↗

Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.

Ajjarapu, Pavan [Oak Ridge National Laboratory (OR↗

The significant impact of cold deformation on structure-property relationship in phase reversion-induced stainless steels

Highlights: • Parts of metastable austenite transformed into strain-induced martensite in 18Cr-8Ni stainless steel during cold-rolled process. • The kinetics of reversion transformation from martensite to austenite was fastest in 90% cold-rolled sample during annealing treatment. • The austenite grain size for the 90% cold-rolled sample after annealing was smallest and most uniform, which induced highest yield strength and elongation combination. - Abstract: The present study aims to investigate the impact of cold deformation on structure-property relationship in phase reversion-induced stainless steels. The commercial 18Cr-8Ni stainless steel was cold rolled at room temperature to 30%, 60% and 90% thickness reduction, respectively and subsequently annealed at 900 °C for 1–100 min. Evolution of phases in selected samples was identified and quantified by X-ray diffraction together with the corresponding microstructural characterization through optical, scanning and transmission electron microscopy, and electron backscatter diffraction. Mechanical properties of selected samples were determined by the tensile test. The results indicated that parts of metastable austenite transformed into strain-induced martensite during cold rolling process, and the volume fraction of martensite increased with increase in cold rolling reduction. The kinetics of reversion transformation from martensite to austenite was fastest in 90% cold-rolled sample during annealing treatment. The austenite grain size for the 90% cold-rolled sample after annealing was smallest and most uniform, which induced highest yield strength and elongation combination.

36 MATERIALS SCIENCE↗

Effect of Aluminum Addition on the Evolution of Microstructure, Crystallographic Texture and Mechanical Properties of Single Phase Hexagonal Close Packed Mg-Li Alloys

In the present investigation, an effort has been made to understand the effect of aluminum addition to α Mg-Li alloys. The corresponding composition Mg-4Li-xAl (x = 0, 2, 4 and 6 wt.%) alloys have been prepared by stir casting route under an argon environment. Extrusion was carried out at 300 °C with the extrusion ratio of 15:1. Significant grain refinement was observed after extrusion. X-ray diffraction-based investigation of the cast and extruded alloys showed the presence of intermetallic compounds such as Mg{sub 17}Al{sub 12} and AlLi in the Al-rich alloys namely, Mg-4Li-xAl (x = 4 and 6 wt.%). These precipitates were also present in the extruded plus annealed samples, indicating the stability of the precipitates at high temperature. The bulk x-ray texture measurement revealed a crystallographic texture where the c-axis of the h.c.p crystals was perpendicular to the extrusion direction (ED) for extruded sample. A texture transition was observed on annealing. The c-axis was oriented parallel to the ED. Mechanical properties of the cast, extruded and extruded plus annealed material illustrate that the addition of Al led to enhancement in hardness, yield strength and ultimate tensile strength.

36 MATERIALS SCIENCE↗

Direct handling of sharp interfacial energy for microstructural evolution

In this study, we introduce a simplification to the previously demonstrated hybrid Potts–phase field (hPPF), which relates interfacial energies to microstructural sharp interfaces. The model defines interfacial energy by a Potts-like discrete interface approach of counting unlike neighbors, which we use to compute local curvature. The model is compared to the hPPF by studying interfacial characteristics and grain growth behavior. The models give virtually identical results, while the new model allows the simulator more direct control of interfacial energy.

36 MATERIALS SCIENCE↗

Effects of high energy Au-ion irradiation on the microstructure of diamond films

The effects of 2.245 GeV Au-ion irradiation and subsequent annealing processes on the evolution of microstructure of diamond films with microcrystalline (MCD) or ultra-nanocrystalline (UNCD) granular structure were investigated, using near edge x-ray absorption fine structure and electron energy loss spectroscopy in transmission electron microscopy. For MCD films, the Au-ion irradiation disintegrated some of the diamond grains, resulting in the formation of nano-sized carbon clusters embedded in a matrix of amorphous carbon (a-C). The annealing process recrystallized the diamond grains and converted the a-C into nano-sized graphite particulates and, at the same time, induced the formation of nano-sized i-carbon clusters, the bcc structured carbon with a{sub 0} = 0.432 nm. In contrast, for UNCD films, the Au-ion irradiation transformed the grain boundary phase into nano-sized graphite, but insignificantly altered the crystallinity of the grains of the UNCD films. The annealing process recrystallized the materials. In some of the regions, the residual a-C phases were transformed into nano-sized graphites, whereas in other regions i-carbon nanoclusters were formed. The difference in irradiation-induced microstructural transformation behavior between the MCD and the UNCD films is ascribed to the different granular structures of the two types of films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗