Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Oxidation of Carbon Fibers in a Cracked Ceramic Matrix Composite Modeled as a Function of Temperature

The oxidation model simulates the oxidation of the reinforcing carbon fibers within a ceramic matrix composite material containing as-fabricated microcracks. The physics-based oxidation model uses theoretically and experimentally determined variables as input for the model. The model simulates the ingress of oxygen through microcracks into a two-dimensional plane within the composite material. Model input includes temperature, oxygen concentration, the reaction rate constant, the diffusion coefficient, and the crack opening width as a function of the mechanical and thermal loads. The model is run in an iterative process for a two-dimensional grid system in which oxygen diffuses through the porous and cracked regions of the material and reacts with carbon in short time steps. The model allows the local oxygen concentrations and carbon volumes from the edge to the interior of the composite to be determined over time. Oxidation damage predicted by the model was compared with that observed from microstructural analysis of experimentally tested composite material to validate the model for two temperatures of interest. When the model is run for low-temperature conditions, the kinetics are reaction controlled. Carbon and oxygen reactions occur relatively slowly. Therefore, oxygen can bypass the carbon near the outer edge and diffuse into the interior so that it saturates the entire composite at relatively high concentrations. The kinetics are limited by the reaction rate between carbon and oxygen. This results in an interior that has high local concentrations of oxygen and a similar amount of consumed carbon throughout the cross section. When the model is run for high-temperature conditions, the kinetics are diffusion controlled. Carbon and oxygen reactions occur very quickly. The carbon consumes oxygen as soon as it is supplied. The kinetics are limited by the relatively slow rate at which oxygen is supplied in comparison to the relatively fast rate at which carbon and oxygen reactions occur. This results in a sharp gradient in oxygen concentration from the edge where it is supplied to the nearest source of carbon, which is where the oxygen is quickly consumed. A moving reaction front is seen in which the outlaying carbon is consumed before the next inner layer of carbon begins to react.

Halbig, Michael C.↗
DOE OSTI2025

Irradiation-induced gas production in REBCO-based magnet materials used for future compact fusion reactors

Nuclear fusion is an enticing alternative to current sources of energy, with multilayered Rare-Earth Barium Copper Oxide (REBCO) coated conductors deemed pivotal in the race toward fully realized, commercially viable, and magnetic confinement fusion reactors. In this study, we simulated the ion spectrum expected to evolve from REBCO's nickel-based Hastelloy C-276 substrate and copper stabilizer in an affordable robust compact-like reactor. We then emulated this gas production through helium implantation to investigate changes in materials and superconducting properties. Our results revealed that the substrate and stabilizer are capable of producing protons energetic enough to recoil throughout the tape thickness in appreciable doses, and alphas energetic enough to deposit 7.54 × 1014 ions/cm2 or 50.1 helium appm in the superconducting layer over a 30-year reactor lifetime. The superconducting layer of SuperPower® tapes exhibited at least double the swelling rate of the other major layers, and both SuperPower and Fujikura Ltd. tapes displayed microstructural changes in the REBCO layer not observed in isotropic metals. For the estimated lifetime fluence, the Fujikura tapes showed a ∼1 K reduction in critical temperature and a 32% degradation in critical current for compact reactor-relevant conditions (16 T, 20 K). Nuclear transmutation, low-temperature solder implantations, gas-ion evolution, the influence of gas production on vortex dynamics, and other related considerations are also discussed.

Reis, Chris↗
DOE OSTI2025

Microstructurally informed synchrotron x-ray analysis revealing helium defect transitions in ultrafine grained tungsten

The formation of insoluble gaseous defects in materials due to nuclear transmutation or ion implantation involves the diffusion of impurity atoms to form atomic defect clusters that coalesce into bubbles or cavities and ultimately degrade the material properties. Transmission electron microscopy (TEM) is limited in its ability to resolve sub-nanometer gas clusters whereas X-ray diffraction (XRD) provides information pertaining to local atomic changes. Here, in this study, helium (He) implanted ultrafine grained tungsten is explored through a multimodal defect characterization campaign combining TEM-informed Small Angle X-ray Scattering (SAXS) analysis, XRD lattice parameter measurements, and nanoscale He cluster quantification from a region of reciprocal space accessible via Wide Angle X-ray Scattering (WAXS). Moderate elevated temperature implantations are shown to produce high concentrations of sub-nanoscale He clusters and small, homogeneously distributed cavities, which collectively are linked to lattice expansion and further substantiated through complementary atomistic simulations. Increased implantation temperatures encourage the diffusion of these defects to the grain boundaries (GBs), leading to lattice relaxation and the growth of large GB cavities manifesting as bimodal size distributions in the SAXS analysis. Overall, our results demonstrate the utility of multimodal synchrotron X-ray analysis in bridging the gap between microscale He cavity quantification and atomic-scale defect analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Documentation, assessment, and improvements of fission gas modeling capabilities in BISON

Fission gas behavior critically affects nuclear fuel performance, influencing thermal conductivity, microstructure, swelling, and fuel-cladding interactions. The Simple Integrated Fission Gas Release and Swelling (Sifgrs) model, implemented within the BISON fuel performance code, provides advanced capabilities for modeling these phenomena. This manuscript reviews and assesses Sifgrs’ modular structure and submodels describing intragranular, intergranular, and release mechanisms. The modular implementation enables rapid improvements as our understanding advances and new fuel forms emerge. After an overview of capabilities, we present a comprehensive validation suite, comparing predictions to experimental data from tests under normal and transient conditions, including reproduction of the Vitanza curve. Results demonstrate Sifgrs’ accuracy, robustness, and applicability. Current limitations and ongoing efforts are discussed, including mechanistic, multiscale modeling, uncertainty quantification, and validation within the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, supporting the safe and efficient use of nuclear fuels.

BISON↗
NASA NTRS1999

Ultrasonic Nondestructive Characterization of Adhesive Bonds

Adhesives and adhesive joints are widely used in various industrial applications to reduce weight and costs, and to increase reliability. For example, advances in aerospace technology have been made possible, in part, through the use of lightweight materials and weight-saving structural designs. Joints, in particular, have been and continue to be areas in which weight can be trimmed from an airframe through the use of novel attachment techniques. In order to save weight over traditional riveted designs, to avoid the introduction of stress concentrations associated with rivet holes, and to take full advantage of advanced composite materials, engineers and designers have been specifying an ever-increasing number of adhesively bonded joints for use on airframes. Nondestructive characterization for quality control and remaining life prediction has been a key enabling technology for the effective use of adhesive joints. Conventional linear ultrasonic techniques generally can only detect flaws (delamination, cracks, voids, etc) in the joint assembly. However, more important to structural reliability is the bond strength. Although strength, in principle, cannot be measured nondestructively, a slight change in material nonlinearity may indicate the onset of failure. Furthermore, microstructural variations due to aging or under-curing may also cause changes in the third order elastic constants, which are related to the ultrasonic nonlinear parameter of the polymer adhesive. It is therefore reasonable to anticipate a correlation between changes in the ultrasonic nonlinear acoustic parameter and the remaining bond strength. It has been observed that higher harmonics of the fundamental frequency are generated when an ultrasonic wave passes through a nonlinear material. It seems that such nonlinearity can be effectively used to characterize bond strength. Several theories have been developed to model this nonlinear effect. Based on a microscopic description of the nonlinear interface binding force, a quantitative method was presented. Recently, a comparison between the experimental and simulated results based on a similar theoretical model was presented. A through-transmission setup for water immersion mode-converted shear waves was used to analyze the ultrasonic nonlinear parameter of an adhesive bond. In addition, ultrasonic guided waves have been used to analyze adhesive or diffusion bonded joints. In this paper, the ultrasonic nonlinear parameter is used to characterize the curing state of a polymer/aluminum adhesive joint. Ultrasonic through-transmission tests were conducted on samples cured under various conditions. The magnitude of the second order harmonic was measured and the corresponding ultrasonic nonlinear parameter was evaluated. A fairly good correlation between the curing condition and the nonlinear parameter is observed. The results show that the nonlinear parameter might be used as a good indicator of the cure state for adhesive joints.

Qu, Jianmin↗
DOE OSTI2026

Reduced‐Order Modeling of Energetic Materials Using Physics‐Aware Recurrent Convolutional Neural Networks in a Latent Space (LatentPARC)

Physics-aware deep learning (PADL) has gained popularity for use in spatiotemporal dynamics simulations, such as those in computational modeling of energetic materials (EM). We show that the challenge PADL methods face while learning complex field evolution problems can be simplified and accelerated by decoupling it into two tasks: learning complex geometric features in evolving fields and modeling dynamics over these features in a lower-dimensional feature space. We build upon our previous work on physics-aware recurrent convolutional neural networks (PARC). PARC embeds knowledge of underlying physics into its neural network architecture for more robust and accurate prediction of evolving physical fields. PARC was shown to effectively learn complex nonlinear features such as the formation of hotspots and coupled shock fronts in various initiation scenarios of EMs, as a function of microstructures, serving effectively as a microstructure-aware burn model. Here, we further accelerate PARC and reduce its computational cost by projecting the original dynamics onto a lower-dimensional invariant manifold, or “latent space.” The projected latent representation encodes the complex geometry of evolving fields (e.g., temperature and pressure) in a set of data-driven features. The reduced dimension of this latent space allows us to learn the dynamics during the initiation of EM with a lighter and more efficient model. We observe a significant decrease in training and inference time while maintaining results comparable to PARC at inference. This work takes steps towards enabling rapid prediction of EM thermomechanics at larger scales and characterization of EM structure–property–performance linkages at a full application scale.

Mathematics and Computing↗
DOE OSTI2024

Demonstration of neutron time-of-flight diffraction with an event-mode imaging detector

Neutron diffraction beamlines have traditionally relied on deploying large detector arrays of 3 He tubes or neutron-sensitive scintillators coupled with photomultipliers to efficiently probe crystallographic and microstructure information of a given material. Given the large upfront cost of custom-made data acquisition systems and the recent scarcity of 3 He, new diffraction beamlines or upgrades to existing ones demand innovative approaches. This paper introduces a novel Timepix3-based event-mode imaging neutron diffraction detector system as well as first results of a silicon powder diffraction measurement made at the HIPPO neutron powder diffractometer at the Los Alamos Neutron Science Center. Notably, these initial measurements were conducted simultaneously with the 3 He array on HIPPO, enabling direct comparison. Data reduction for this type of data was implemented in the MAUD code, enabling Rietveld analysis. Results from the Timepix3-based setup and HIPPO were benchmarked against McStas simulations, showing good agreement for peak resolution. With further development, systems such as the one presented here may substantially reduce the cost of detector systems for new neutron instrumentation as well as for upgrades of existing beamlines.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1978

Shear rupture of a directionally solidified eutectic gamma/gamma prime - alpha (Mo) alloy

Directionally solidified Mo alloys are evaluated to determine the shear rupture strength and to possibly improve it by microstructural and heat treatment variations. Bars of the alloy containing nominally 5.7% Al and 33.5% Mo by weight with balance Ni were directionally solidified at rates between 10 and 100 mm per hour in furnaces with thermal gradients at the liquid-solid interface of 250 or 100 C per cm. A limited number of longitudinal shear rupture tests were conducted at 760 C and 207 MPa in the as - solidified and in several heat treated conditions. It is shown that shear rupture failures are partly transgranular and that resistance to failure is prompted by good fiber alignment and a matrix structure consisting mainly of gamma prime. Well aligned as - solidified specimens sustained the shear stress for an average of 81 hours. A simulated coating heat treatment appeared to increase the transformation of gamma to gamma prime and raised the average shear life of aligned specimens to 111 hours. However, heat treatments at 1245 C and especially at 1190 C appeared to be detrimental by causing partial solutioning of the gamma prime, and reducing lives to 47 and 10 hours, respectively.

Harf, F. H.↗
NASA NTRSDate not supplied

Multiscale Modeling of Woven Ablative Thermal Protection System Materials

The NASA Entry Systems Modeling project maintains a portfolio of computational model and tool development activities focused on reducing performance uncertainties in ablative Thermal Protection System (TPS) materials for NASA missions. The development activities span material scale and strive to allow microstructural characterization of material structure and properties, mesoscale analyses of damage, and macroscale evaluation of heatshield performance and recession in a given aerothermodynamic environment. This talk will detail the application of developed capabilities at all three scales to the woven TPS material that the Agency has selected as the heatshield for the Mars Sample Return Earth Entry System (MSR-EES) mission – 3D Mid-Density Carbon Phenolic (3MDCP). Each of the applications focuses on driving down uncertainties in material performance and thus risk for MSR-EES and other future missions that may leverage woven TPS. At the microscale, machine learning techniques are used to characterize images from destructive microscopy and inform structural variability. At the mesoscale, Lagrangian techniques are used to simulate ballistic impact and interpret damage modes noted in experiments. At the macroscale, coupled flow-material response techniques are validated by Arc Jet testing to enable heatshield design for missions with massive ablation.

Justin B Haskins↗
DOE OSTI2025

Topological Defect Mediated Helical Phase Reorientation by Uniaxial Stress

Strain engineering enables precise, energy-efficient control of nanoscale magnetism. However, unlike well-studied strain-dislocation interactions in mechanical deformation, the spatial evolution of strain-induced spin rearrangement remains poorly understood. Using Lorentz transmission electron microscopy, we manipulate and observe helical domain reorientation under quantitatively applied uniaxial tensile stress. Our findings reveal striking similarity to plastic deformation in metals, where the critical stress for propagation vector ( Q ) reorientation depends on its angle with the stress direction. Magnetic defects mediate reorientation via “break-and-reconnect” or “dislocation gliding–annihilation” processes. Simulations confirm that strain-induced anisotropic Dzyaloshinskii-Moriya interaction may play a key role. These insights advance strain-driven magnetism and offer a promising route for energy-efficient magnetic nanophase control in next-generation information technology. Published by the American Physical Society 2025

36 MATERIALS SCIENCE↗
DOE OSTI2026

State of the art, gaps, and prospects in fusion materials theory and modelling

Advancing the theory and simulation of materials for fusion applications remains a key component of global roadmaps aimed at delivering much-needed fusion power. Especially as the drive for commercial application increases, prototypes must be designed against radiation damage before the relevant experimental data can be collected and cost reductions that are possible by testing materials in silico become even more important. Here, we summarise the state of the art as it emerged during the 7 th Fusion Materials Theory & Modelling Workshop that took place in 2024, with the aim to highlight present gaps and future directions for the fusion materials modelling community. Of particular interest were the effects of transmutations, chemical complexity with the development of novel alloys and interatomic potentials, advancements in modelling high-dose microstructures, comparison with experimental data and multiscale models for structural assessment relying on high-performance computing and virtual reality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Structural uniformity and compositional homogeneity of solid-phase alloyed rod

Solid-phase processes have emerged as an alternative to fusion-based alloying to avoid coarse microstructures, undesirable phase formation, and high energy consumption. However, achieving uniform distribution of alloying elements during friction-based processing remains challenging due to highly heterogeneous thermomechanical conditions. This work evaluates the structural uniformity and compositional homogeneity of Al–Cu–Zn alloyed rods produced by friction extrusion (FE) and establishes the role of the rotational speed to feed rate ratio (N/V) on alloying effectiveness. A systematic matrix of FE experiments was conducted at constant extrusion ratio with N/V values ranging from 3.7 to 300. Compositional uniformity was assessed along the rod length (ICP-OES), in three dimensions (X-ray computed tomography), and at the microscale (SEM–EDS), supported by a gray-level co-occurrence matrix (GLCM)–based homogeneity metric. Smoothed particle hydrodynamics (SPH) simulations were used to reveal material flow and thermomechanical fields. Results show that N/V = 100 produces a high-shear mixing zone that eliminates the unmixed core and enables near-full dissolution and dispersion of Cu and Zn. At lower N/V, a laminar flow region persists at the rod center, causing segregation and large composition gradients. The combined experimental–computational analysis provides mechanistic insight into the transition from fragmented particle dispersion to thermomechanically assisted metallurgical mixing. This study establishes processing–structure relationships for solid-phase alloying and provides guidance for achieving homogenized compositions comparable to wrought alloys via rapid, scalable FE processing.

Aluminum↗
DOE OSTI2025

Stochastic 3D reconstruction of cracked polycrystalline NMC particles using 2D SEM data

Li-ion battery performance is strongly influenced by the 3D microstructure of its cathode particles. Cracks within these particles develop during calendaring and cycling, reducing connectivity but increasing reactive surface, making their impact on battery performance complex. Understanding these contradictory effects requires a quantitative link between particle morphology and battery performance. However, informative 3D imaging techniques are time-consuming, costly and rarely available, such that analyses often have to rely on 2D image data. This paper presents a novel stereological approach for generating virtual 3D cathode particles exhibiting crack networks that are statistically equivalent to those observed in 2D sections of experimentally measured particles. Consequently, 2D image data suffices for deriving a full 3D characterization of cracked cathodes particles. Such virtually generated 3D particles could serve as geometry input for spatially resolved electro-chemo-mechanical simulations to enhance our understanding of structure-property relationships of cathodes in Li-ion batteries.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

A Combined Computational, Experimental, and Technology Development Approach to In-Space Laser Manufacturing Maturation at NASA Marshall Space Flight Center

In-space manufacturing (ISM) is emerging as a field vital to continued access and capabilities in the space environment. NASA Marshall Space Flight Center (MSFC) is advancing the frontier of in-space laser manufacturing (ISLM) techniques through work initially focused on maturing laser beam welding (LBW) and laser forming (LF) for use in space. Such techniques proffer the ability to assemble and join structures in space from sheet metal or other stock – extant satellites, in situ resource utilization of Lunar regolith, etc. – by forming to desired shapes and then joining via in-space welding (ISW). ISLM processes are useful for assembly, joining, modification, and repair of structures in free space and on the Lunar surface such as large observatories, antennas, trusses, blast/thermal/radiation shields, pressure vessels, and more. However, these techniques are not yet qualified & certified (Q&C) for regular application in space. It would be prohibitively expensive, laborious, and time-consuming to perform Q&C via traditional experimental approaches as data collection & experimentation in space is resource-intensive. As such, benchmark experiments and focused, properly instrumented technology demonstration efforts in space can collect sufficient data that – when combined with verified computational models in an integrated computational materials engineering (ICME) approach – can validate ICME tools capable of translating more readily obtained ground data to in-space, in situ, computationally informed Q&C of ISLM techniques. Several ISLM projects at MSFC are obtaining the data required to validate ICME tools through both ground and flight experiments. A parabolic flight experiment of LBW under vacuum is manifested for August 2024, including both microgravity and Lunar gravity profiles. This collaboration with the Ohio State University is investigating common aerospace alloys such as 316L stainless steel, 2219 aluminum alloy, and Ti64 titanium alloy. In situ data collection includes videography, thermography, and reference thermocouples to build a thermal model of the welds. This will elucidate the relevant physics when combined with post-flight microstructural examination and mechanical testing. MSFC is also progressing towards a suborbital flight experiment of LBW under vacuum, which could provide reams of data on ISW during sustained, high-quality reduced gravity. The effect of combined thermal (cryogenic and high-temperature) and vacuum exposure on both LBW (NASA-funded) and LF (DARPA-funded) is being investigated through ground experiments. In addition to the copious data collected during these ground experiments, ruggedization of LBW hardware will also be pursued. The datasets from these experiments will be used to validate computational models which will inform future ISLM efforts in an ICME framework. A variety of techniques across lengths scales, from CALPHAD-driven thermodynamics & kinetics to phase field modeling of solidification to kinetic Monte Carlo simulations of grain evolution at the mesoscale, will be employed to accelerate the infusion and eventual Q&C of LBW and LF for use in space. The development of data-driven surrogate models to bridge ground to flight experiments and thereby reduce the need for resource-intensive experiments in space will also be investigated. These ICME techniques, surrogate models, and datasets from ground testing can also be employed to advance manufacturing in terrestrial environments.

in-space welding↗
NASA NTRS2023

Microstructural Changes and Pb Mobility During the Zircon to Reidite Transformation: Implications for Planetary Impact Chronology

Impact events modify and leave behind a complex history of rock metamorphism on terrestrial planets. Evidence for an impact event may be recorded in physical changes to minerals, such as mineral deformation and formation of high P-T polymorphs, but also in the form of chemical fingerprints, such as enhanced elemental diffusion and isotopic mixing. Here we explore laboratory shock-induced physical and chemical changes to zircon and feldspar, the former of which is of interest because its trace elements abundances and isotope ratios are used extensively in geochemistry and geochronology. To this end, a granular mixture of Bishop Tuff sanidine and Kuehl Lake zircon, both with well characterized Pb isotope compositions, was prepared and then shocked via a flat plate accelerator. The peak pressure of the experiment, as calculated by the impedance matching method, was ~24 GPa although a broader range of P-T conditions is anticipated due to starting sample porosity. Unshocked and shocked materials were characterized via scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and Raman spectroscopy. These methods show that the starting zircon material had abundant metamict regions, and the conversion of the feldspar to glass in the post-shock material. Analyses of the shocked product also yielded multiple occurrences of the high-pressure ZrSiO 4 polymorph reidite, with some domains up to 300 μm across. The possibility of U-Pb system disturbance was evaluated via laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) and secondary ion mass spectrometry (SIMS). The isotopic data reveal that disturbance of the U-Pb geochronometer in the reidite was minimal (<2% for the main U-Pb geochronometers). To better constrain the P-T conditions during the shock experiment, we complement impedance matching pressure calculations with iSALE2D impact simulations. The simulated results yield a range of P-T conditions experienced during the experiment and show that much of the sample may have reached >30 GPa, which is consistent with formation of reidite. In the recovered shocked material, we identified lamellae of reidite, some of which interlock with zircon lamellae. Reidite {112} twins were identified, which we interpret to have formed to reduce stress between the crystal structure of the host zircon and reidite. These two findings support the interpretation that shear transformation enabled the transition of zircon to reidite. The size and presence of reidite found here indicate that this phase is probably common in impact-shocked crustal rocks that experienced ~25 to ~35 GPa, especially when the target material has porosity. Additionally, shock loading of the zircon and transformation to reidite at these pressures in porous materials is unlikely to significantly disturb the U-Pb system in zircon and that the reidite inherits the primary U and Pb elemental and isotopic ratios from the zircon.

Bishop Tuff↗
DOE OSTI2025

Probing Surface Plasmon Dynamics in Periodic Nanostructures through Ultrafast Electron Microscopy

Surface plasmon polaritons (SPPs) can be manipulated to localize and guide light in subwavelength distances, enabling them to find applications in a wide range of areas, from sensing to quantum computing. Among several methods of SPP excitation, periodic arrays of nano- and microstructures are of particular interest, as they enable engineering SPP properties through structural parameters. Here, in this study, using the photon-induced near-field electron microscopy (PINEM) technique, we investigated the mode formation, coupling, interference, and decay of SPPs in square and hexagonal arrays of circular nanoholes under both visible and near-infrared excitation. Polarization-resolved analysis revealed the key factors governing SPP localization and interference patterns, showing that the periodicity and symmetry of the array primarily determine the SPP interference patterns and their orientation, while pump polarization mainly modulates their intensity. Time-resolved PINEM measurements demonstrated the spatial dependence of the SPP temporal characteristics. In addition, cathodoluminescence (CL) spectroscopy was employed to examine the intrinsic plasmonic characteristics of the structure. Finite difference time domain (FDTD) simulations showed strong agreement with both PINEM and CL measurements on the spatial and spectral behavior of SPPs. Understanding the spatiotemporal dynamics of SPPs on nanostructures beyond the diffraction limit is crucial for optimizing plasmonic structures for advanced photonic and quantum technologies.

Plasmonics↗
NASA NTRS1995

Effects of low earth orbit on the optical performance of multi-layer enhanced high reflectance mirrors

Two mirror designs developed for space applications were flown along with a standard mid-infrared design on the leading and trailing edges of the Long Duration Exposure Facility (LDEF). Preliminary observations of induced changes in optical performance of ZnS-coated mirrors and impact-related microstructural and microchemical effects are described in the proceedings of the First LDEF Post-Retrieval Symposium. In this paper, effects of the induced environment and meteoroid/debris impacts on mirror performance are described in more detail. Also, an analysis of reflectance spectra using the results of Auger and secondary ion mass spectroscopy (SIMS) profiling measurements are used to identify an optical-degradation mechanism for the ZnS-coated mirrors. Structural damage associated with a high-velocity impact on a (Si/Al2O3)-coated mirror was imaged optically and with scanning electron and atomic force microscopy (SEM and AFM). Scanning Auger and SIMS analysis provided chemical mapping of selected impact sites. The impact data suggest design and fabrication modifications for obtaining improved mechanical performance using a design variation identified in preflight laboratory simulations. Auger surface profile and SIMS imaging data verified the conclusion that secondary impacts are the source of contamination associated with the dendrites grown on the leading-edge ZnS-coated test samples. It was also found that dendrites can be grown in the laboratory by irradiating contaminated sites on a trailing-edge ZnS-coated sample with a rastered electron beam. These results suggest a mechanism for dendrite growth.

Donovan, Terence↗
NASA NTRS2019

Myco-Architecture off Planet: Growing Surface Structures at Destination

Our work focused on filling major select key technical knowledge gaps, and technical aspects to be addressed in a Phase II proposal were identified such as the secretion of glues or plastics by the fungi or bacteria to form biocomposites. Specifically, we raised the technical TRL by assessing the growth of in-house mycelial-producing strains on potential food substrates and analyzed the advantages and disadvantages to their use off planet. Growth of the mycelia on sawdust and powdered nutrients including dried, powdered algae, was used as a baseline. We measured growth as a function of temperature, tested the relevant material properties of the mycelia products produced, and measured the mass of input and output volume for production per volume of material. Mycotecture was produced in a bag simulating the proposed mission implementation. Post-production such as heat treatment (as is done with terrestrial mycotecture)was assessed.The material properties of the dried, frozen and baked mycelial outputs included density, strength,thermal insulation and flame retardation. Tensile/compression testing on biocomposite material specimens was performed to obtain three-dimensional elastic constants, as well as to examine deformation and fracture behavior. These mechanical tests were performed on both dormant and activated samples to understand the evolution of the structural material. In addition, experimental data obtained from the mechanical testing was used to build a failure prediction model that accounts for material anisotropy. This aided in future structural design through a quantitative understanding of the mechanical limits of the material. To examine the texture, defects, fracture surfaces of the material, high-resolution microstructural imaging was utilized before and after the mechanical tests. This microstructural analysis informed us about the macro-structural behavior and influenced structural design. Thermal decomposition analysis was also performed tounderstand the thermal limits.

Biocomposites↗