SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An improved procedure for making perfluoralkylethestriazine elastomers, and, more specifically, the synthesis of 2.4- perfluoroalkenlether-6-perfluoroalkylether triazine is reported.
Results are presented for measurements of the fluorescence spectra of polystyrene in dilute solution and in pure solid films. It is determined that a major potential source of experimental error is the concurrent photooxidative degradation in air which may obscure fluorescence emission from monomeric sites in solid films at 25 C. The fluorescence spectra of oriented films are evaluated in terms of the monomer to excimer fluorescence intensity ratio and the excimer 'red shift'. The monomer to excimer fluorescence intensity ratio is determined to be significantly higher in fluid solution than in solid film.
Sealed nickel cadmium cells having undergone a large number of cycles were discharged using the Hg/HgO reference electrode. The negative electrode exhibited the second plateau. SEM of negative plates of such cells show clusters of large crystals of cadmium hydroxide. These large crystals on the negative plates disappear after continuous overcharging in flooded cells. Atomic Absorption Spectroscopy and standard wet chemical methods are being used to determine the cell materials viz: nickel, cadmium, cobalt, potassum and carbonate. The anodes and cathodes are analyzed after careful examination and the condition of the separator material is evaluated.
The effects of humidity (water-vapor) in nitrogen on the friction and deformation behavior of magnetic tape in contact with a Ni-Zn ferrite spherical pin were studied. The coefficient of friction is markedly dependent on the ambient relative humidity. In elastic contacts the coefficient of friction increased linearly with increasing humidity; it decreased linearly when humidity was lowered. This effect is the result of changes in the chemistry and interaction of tape materials such as degradation of the lubricant. In plastic contacts there was no effect of humidity on friction below 40 percent relative humidity. There is no effect on friction associated with the breakthrough of the adsorbed water-vapor film at the interface of the tape and Ni-Zn ferrite. The coefficient of friction, however, increased rapidly with increasing relative humidity above 40 percent in plastic contacts.
Nickel-cadmium rechargeable batteries are a vital and reliable energy storage source for aerospace applications. As the demand for longer life and more reliable space batteries increases, the understanding and solving of cell aging factors and mechanisms become essential. Over the years, many cell designs and manufacturing process changes have been developed and implemented. Cells fabricated with various design features were life cycled in a simulated low-Earth orbit regime. Following the test program, a comprehensive electrochemical analysis of cell components was undertaken to study cell degradation mechanisms. Discharge voltage degradation or voltage plateau has been observed during orbit cycling, but, its cause and explanation have been the subject of much discussion. A Hg/HgO reference electrode was used to monitor the reference versus each electrode potential during the discharge of a cycled cell. The results indicate that the negative electrode was responsible for the voltage plateau. Cell analysis revealed large crystals of cadmium hydroxide on the surface of the negative electrode and throughout the separator.
Experimental data concerning emission of light upon dehydration as a function of preheating and pre-gamma-irradiation are correlated with reported studies of electron-spin resonance (ESR) activity after similar pretreatments. The effect of these pretreatments on the kaolin-promoted incorporation of glycine into peptide oligomers in a wet/cold, hot/dry fluctuating environment is compared to their effect on the ESR and luminescent signals. The existence of spectroscopically active centers appears to be loosely anticorrelated with reaction yield; these yields are increased by increasing the overall energy content of the material. It is concluded that some part of the chemical yield is produced by a mechanism involving intrinsic, excited electronic states of the clay crystal lattice. These states may be derived from thermally, interfacially, and/or mechanically induced charge reorganization within interspersed energy levels in the band structure of the material.
The constitutive equation for the relaxation behavior of time-dependent, chemically unstable materials developed by Valanis and Peng (1983), which used the irreversible thermodynamics of internal variables in Eyring's absolute reaction theory and yielded a theoretical expression for the effect of chemical crosslink density on the relaxation rate, is presently applied to the creep behavior of a network polymer which is undergoing a scission process. In particular, two equations are derived which may for the first time show the relations between mechanical models and internal variables in the creep expressions, using a three-element model with a Maxwell element.
The development of crystal handling techniques for reflection infrared spectroscopy and methods for the fabrication and testing of tensile specimens are discussed. Data from mechanical, ac and dc electrical, and electron paramagnetic resonance studies conducted to determine the effects of 0.1-MeV and 1.0-MeV electron radiation on Mylar, Kapton, Ultem, and metal-doped Ultem are presented. Total doses ranging from 1 X 10 to the 8 rads to 1 X 10 to the 10 rads and dose rates from 5 X 10 to the 7 rads/hr to 1 X 10 to the 9 rads/hr were employed. The results of a study on the effects of aircraft service-environment fluids on Ultem are also reported. The weights and mechanical properties of Ultem were evaluated before and after exposure to water, JP4, Skydrol, an antifreeze, and a paint stripper.
Dynamic dielectric analysis has been used to study curing polymer systems and thermoplastics. Measurements have been made over a frequency range of six decades. This wide range of frequencies increases the amount of information which can be obtained. The data are analyzed in terms of the frequency dependence of the specific conductivity sigma and the relaxation time tau, parameters which are characteristic of the cure state of the material and independent of size of the sample. Dynamic dielectric measurements have been correlated with viscosity for the polysulfone thermoplastic UDEL-P1700 and with viscosity and ultrasonic measurements on the DGEBA-type epoxy Epon 828 cured with Agent U. The experimental results suggest that when ionic processes dominate the dielectric response, the intensive property sigma is a good monitor of the resin's viscosity. The results show that the dielectric relaxation time tau can be used to monitor the state of the system and the extent and rate of the reaction.
A number of ethynylated aromatic monomers recently have been synthesized which thermally homopolymerize and copolymerize to produce rigid, highly cross-linked polymers with high thermal stability (Tg of about 450 C). On pyrolysis, these polymers lose few volatiles (more than 85 percent char yield) to yield carbon bodies of relatively low porosity. These properties render the ethynylated aromatics of significant interest as matrices for high temperature composites. Incorporation of a SiC particle filler in the matrix improves the rheology of the system and minimizes shrinkage during pyrolysis. Several unidirectional composites have been fabricated combining a graphite or boria-alumina-silica continuous reinforcement with an ethynylated aromatic polymer matrix and SiC filler. Thermogravimetric analysis of composite pyrolysis behavior was used to determine reaction kinetics and to establish a composite fabrication cycle. Composites retained 95 percent of their green weight on pyrolysis. Microstructure of the green and pyrolyzed composites is characterized for materials pyrolyzed at 600 C in vacuum and argon as well as for laminates heated at 1200 C in argon following pyrolysis.
Silicon carbide made by pyrolizing polymers. Method conceived for preparation of poly(decamethylcyclohexasilanes) as precursors for preparation of silicon carbide at high yield. Technical potential of polysilanes as precursors of SiC ceramics being explored. Potential limited by intractability of some polysilanes; formation of small, cyclic polycarbosilane fragments during pyrolysis; and overall low char yield and large shrinkage in conversion to ceramics.
A study is presented of the effect of radiation on polymers. It helps to estimate the impact of the space environment on composite structures. Two commercially available polymer films were used; a polyetherimide, and a polysulfone. Both films were irradiated in vacuum with 85 KeV electron. Properties of the films before and after irradiation were monitored by tensile elongation measurements, ultraviolet/visible spectroscopy, glass transition temperature measurements, gel permeation chromatography, and infrared spectroscopy. The results of these characterizations are presented and briefly discussed.
Intensity and lifetime quenching of the polystyrene monomer and excimer fluorescence emission by a pendant quencher have been studied in the solid state and in solution for a series of copolymers of styrene and 2-(2-prime-hydroxy-5-prime-vinylphenyl)-2H-benzotriazole. Two mechanisms of quenching have been identified. One involves interception of the migrating monomer excitation by the quencher, and the other involves a single-step Foerster energy-transfer process from the excimer traps to a quencher. The relative efficiencies of these two quenching mechanisms in the solid state and in solution have been compared and related to the efficiency of electronic energy migration. An estimate of the excimer trap concentration in solid polystyrene is also reported.
The early Shuttle flights and the attendant opportunity to deploy material samples to the near-Earth space environment, along well-defined trajectories and accompanied by detailed characterization of these samples prior to and following the flight exposure, have brought to light several novel phenomena associated with interaction of these materials with the space environment. JPL, in coordination with other NASA Centers, has carried out a research program to study the degradation and oxidation processes caused by interaction of these materials with atomic oxygen at an energy of 5 eV. In addition, energetic atomic oxygen is believed to be responsible for the shuttle glow first observed during the flight of STS-3. The shuttle glow phenomenon has been extensively studied and modeled because of its long-range potential impact on optical communication schemes and its more immediate impact on the Space Telescope. This report summarizes the results of certian material degradation and erosion experiments carried out aboard STS-8 between August 30, 1983 and September 5, 1983. Based on these data, a generic degradation model has been developed for common structural polymers.
A wick for use in a capillary loop pump heat pipe is described. The wick material is an essentially uniformly porous, permeable, open-cell, polyethylene thermoplastic foam having an ultrahigh average molecular weight of from approximately 1 to 5 million, and an average pore size of about 10 to 12 microns. A representative material having these characteristics is POREX UF, which has an average molecular weight of about 3 million. This material is fully compatible with the FREONs and anhydrous ammonia and allows for the use of these very efficient working fluids in capillary loops.
At the altitudes of low-earth orbit (LEO), atomic oxygen (AO) is the most abundant chemical species. This strong oxidizing agent reacts with virtually any organic material that is not already fully oxidized. Erosion by AO can be extensive and jeopardizes any protective coatings, thermal blankets, adhesives, and structural composites exposed on the exterior of satellites in LEO. Researchers prepared and tested organic materials for their susceptibility to AO using a commercial plasma asher which approximately simulates the oxygen effects in LEO. Experiments were performed on a polyimide, a polysulfone, and two epoxy adhesives into which low molecular-weight additives have been dissolved. Incorporated in the molecular structure of these additives are elements such as silicon whose nonvolatile oxides, which are formed on exposure to AO, remain as a coating on the surface to create a barrier between the remainder of the organic material and the AO. We find that the additives protect the materials, but the low solubility of some limit their utility. Concurrent studies are underway to measure the effect of the additives on the thermal expansion coefficients of the materials. Tows of aramid fibers, which are important components in the proposed tether satellite systems, have been eroded in the asher. The results which show that the square root of the mass remaining decreases linearly with the time of exposure (see the figure) are consistent with a constant rate of surface erosion. The tensile strength of these eroded tows decreases with time of exposure also; additional measurements are in progress.
The combined effects of thermal cycling and high-dose electron irradiation on the mechanical properties of laminated graphite/polymeric CFRPs are investigated experimentally. The test apparatus and procedures are briefly described, and the results are presented in extensive tables and graphs. It is found that electron radiation produces similar significant reductions in the glass transition temperatures of the neat resins and CFRPs. The radiation-induced degradation products tend to plasticize the matrix at high temperature but embrittle it at low temperature.
The concept of uniformly and continuously depositing and sinter-fusing nominal 0.1 to 40 microns dimensioned electrostatically charged polymer powder particles onto essentially uniformly spread 5 to 20 micron grounded continuous fiber tow to produce a respoolable thermoplastic composite two-preg was formulated at NASA Langley. The process was reduced to practice under a NASA grant at the University of Akron this spring. The production of tow-preg is called phase 1. The production of ultrafine polymer powders from 5 to 10 percent (wt) polymer solids in solvent is considered. This is phase 0 and is discussed. The production of unitape from multi tow-pregs was also considered. This is phase 2 and is also discussed. And another approach to phase 1, also proposed last summer, was scoped. This is phase 1A and is also discussed.