SEARCH · Search NASA

Results for “Pressure interference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Investigation of the unsteady pressure distribution on the blades of an axial flow fan

The unsteady response of a stator blade caused by the interaction of the stator with the wakes of an upstream rotor was investigated. Unsteady pressure distributions were measured using a blade instrumented with a series miniature pressure transducers. The influence of several geometrical and flow parameters - rotor/stator spacing, stator solidity and stator incidence angle - were studied to determine the unsteady response of the stator to these parameters. A major influence on the stator unsteady response is due to the stator solidity. At high solidities the blade-to-blade interference has a larger contribution. While the range of rotor/stator spacings investigated had a minor influence, the effect of stator incidence angle is significant. The data indicate the existence of an optimum positive incidence which minimizes the unsteady response.

Henderson, R. E.↗

NASA NTRS1988

A panel method procedure for interference assessment in slotted-wall wind tunnels

This paper describes a method for three-dimensional wind tunnel interference assessment developed specifically for slotted-wall tunnels. The method is an adaptation to the assessment problem of a previously published high-order panel method procedure for simulating the flow in slotted-wall tunnel test sections. The method uses a mixed outer boundary condition, primarily a Neumann condition, with measured pressure constraints used to control only those boundary phenomena which can not be specified accurately a priori. Assessment results are illustrated from a calibration test with variations in wall geometry, and from tests of a generic subsonic transport aircraft configuration.

Kemp, William B., Jr.↗

NASA NTRS1992

Some considerations on the integration of engine nacelles into low-boom aircraft concepts

A study of wind-tunnel data has shown why unexpected strong shock waves appeared in wind tunnel pressure signatures of two low-boom models, and has indicated that changes to the current methods for analyzing and designing low-boom aircraft are needed. The discussion provided corrections for the interface lift code, and suggested methods of treatment for the equivalent areas of the aircraft, especially the nacelles and the interference lift, which were to be used in the aircraft design and the sonic boom analysis.

Mack, Robert J.↗

NASA NTRS2010

Recent Stirling Conversion Technology Developments and Operational Measurements at NASA Glenn Research Center

In support of the Advanced Stirling Radioisotope Generator (ASRG) project and other potential applications, NASA Glenn Research Center (GRC) has initiated convertor technology development efforts in the areas of acoustic emission, electromagnetic field mitigation, thermoacoustic Stirling conversion, and multiple-cylinder alpha arrangements of Stirling machines. The acoustic emission measurement effort was developed as a health monitoring metric for several Stirling convertors undergoing life testing. While accelerometers have been used in the past to monitor dynamic signature, the acoustic sensors were chosen to monitor cycle events, such gas bearing operation. Several electromagnetic interference (EMI) experiments were performed on a pair of Advanced Stirling Convertors (ASC). These tests demonstrated that a simple bucking coil was capable of reducing the alternating current (ac) magnetic field below the ASRG system specification. The thermoacoustic Stirling concept eliminates the displacer typically found in Stirling machines by making use of the pressure oscillations of a traveling acoustic wave. A 100 W-class thermoacoustic Stirling prototype manufactured by Northrop Grumman Space and Technology was received and tested. Another thermoacoustic prototype designed and fabricated by Sunpower, Inc., will be tested in the near future. A four cylinder free piston alpha prototype convertor was received from Sunpower, Inc. and has been tested at GRC. This hardware was used as a proof of concept to validate thermodynamic models and demonstrate stable operation of multiple-cylinder free-piston Stirling conversion. This paper will discuss each of these activities and the results they produced.

Oriti, Salvatore M.↗

DOE OSTI2025

Development of a wide bandwidth heterodyne dispersion interferometer for electron density measurement of atmospheric pressure plasmas

One of the challenges of electron density measurements of an atmospheric pressure plasma (APP) with a laser interferometer is the significant and unwanted phase shift caused by changes in the neutral gas density. These unwanted phase shifts can be mitigated and plasma density measured using an interferometer architecture called a dispersion interferometer (DI). A DI is composed of two nonlinear orientation patterned GaAs crystals for frequency doubling and measures the phase shift induced by a plasma in the interference signal between two second-harmonic beams. Measurement of plasma dynamics or a short plasma pulse in less than a millisecond is enabled with heterodyne detection in a DI using an acousto-optic cell with a frequency of 40 MHz. This heterodyne DI (HDI) is targeted to measure APPs in an electron density range of 10 20 –10 24 m −3 . Finally, the HDI achieves a line-integrated density resolution of 2 × 10 15 m −2 (a phase resolution of 0.005°) with a time constant of 1 μs using ensemble averaging techniques.

atmospheric pressure plasma↗

NASA NTRS1985

Numerical study of three-dimensional turbulent flow interactions between blockage models and wind tunnels including longitudinally slotted test sections

A spatial forward-marching approach is applied to compute three-dimensional turbulent flows for several blockage models in free flight, in a solid wall wind tunnel, and in a wind tunnel with longitudinal slots in the test section. The effects of area blockage in the tunnel, model growth and tunnel wall boundary layers, and of the slots are included. The large blockage models are found to have significant wall interference effects which can be reduced by the slots. The effects of the latter are confined to the region near the tunnel wall. Model/wall interference effects are not limited to the effects of area blockage; in particular, boundary layer profile shapes for a wind tunnel model in a tunnel are different from shapes for a model in free flight even when slots are used. This indicates that the flow responds differently in these two cases with the same pressure gradient.

Lin, S.-J.↗

NASA NTRS1998

Qualification of the Tropical Rainfall Measuring Mission Solar Array Deployment System

The Tropical Rainfall Measuring Mission (TRMM) solar arrays are placed into orbital configuration by a complex deployment system. Its two wings each comprise twin seven square solar panels located by a twelve foot articulated boom. The four spring-driven hinge lines per wing are rate-limited by viscous dampers. The wings are stowed against the spacecraft kinematically, and released by five pyrotechnically-actuated mechanisms. Since deployment failure would be catastrophic, a total of 17 deployment tests were completed to qualify the system for the worst cast launch environment. This successful testing culminated in the flawless deployment of the solar arrays on orbit, 15 minutes after launch in November 1997. The custom gravity negation system used to perform deployment testing is modular to allow its setup in several locations, including the launch site in Japan. Both platform and height can be varied, to meet the requirements of the test configuration and the test facility. Its air pad floatation system meets tight packaging requirements, allowing installation while stowed against the spacecraft without breaking any flight interfaces, and avoiding interference during motion. This system was designed concurrently with the deployment system, to facilitate its installation, to aid in the integration of the flight system to the spacecraft, while demonstrating deployment capabilities. Critical parameters for successful testing were alignment of deployment axes and tables to gravity, alignment of table seams to minimize discontinuities, and minimizing pressure drops in the air supply system. Orbital performance was similar to that predicted by ground testing.

Lawrence, Jon↗

DOE OSTI2023

Rapid Simulation of Unconventional Reservoirs by Multidomain Multiresolution Modeling Based on the Diffusive Time of Flight

Summary The fast marching method (FMM)-based rapid flow simulation has been shown to accelerate simulation efficiency by orders of magnitude by transforming 3D simulation to equivalent 1D simulation using the concept of the “diffusive time of flight” (DTOF). However, the 1D transformation does not directly apply to multiwell problems. In this paper, we propose a novel DTOF-based multidomain multiresolution discretization scheme to accelerate multiwell simulation of unconventional reservoirs. Our method formulates multiwell simulation problems based on the DTOF which displays the pressure front propagation in unconventional reservoirs. The DTOF contours are used to partition the reservoir into local and shared domains. A local domain is where the flow is dominated by a single well, and the shared domain is where the fluid flow is influenced by multiple wells. The DTOF contours expand independently in local domains and interfere in the shared domain. After the partitioning, each domain is discretized using a multiresolution scheme whereby the original 3D fine mesh is preserved near the wells to account for detailed physics including gravity, and the rest of the domain is discretized into 1D mesh based on the DTOF contours to alleviate the simulation workload. The power and efficacy of our approach are demonstrated using synthetic and field-scale simulation models with different degrees of geologic and well-completion complexity. The simulation results, number of active cells, and computation time for the proposed discretization scheme are compared with the original high-fidelity 3D model for each case. The results show that the proposed method is suitable for multiwell simulation problems in unconventional reservoirs and can accelerate flow simulations by orders of magnitude with minimal loss of accuracy. The novelty of this work is the creation of DTOF-derived multiresolution discretization with local and shared domains to simplify and accelerate the calculation of subsurface flow problems, especially in unconventional reservoirs. Our workflow can be easily interfaced with commercial simulators, making it suitable for large-scale field applications.

Engineering↗

NASA NTRS1973

Prediction of space shuttle fluctuating pressure environments, including rocket plume effects

Preliminary estimates of space shuttle fluctuating pressure environments have been made based on prediction techniques developed by Wyle Laboratories. Particular emphasis has been given to the transonic speed regime during launch of a parallel-burn space shuttle configuration. A baseline configuration consisting of a lightweight orbiter and monolithic SRB, together with a typical flight trajectory, have been used as models for the predictions. Critical fluctuating pressure environments are predicted at transonic Mach numbers. Comparisons between predicted environments and wind tunnel test results, in general, showed good agreement. Predicted one-third octave band spectra for the above environments were generally one of three types: (1) attached turbulent boundary layer spectra (typically high frequencies); (2) homogeneous separated flow and shock-free interference flow spectra (typically intermediate frequencies); and (3) shock-oscillation and shock-induced interference flow spectra (typically low frequencies). Predictions of plume induced separated flow environments were made. Only the SRB plumes are important, with fluctuating levels comparable to compression-corner induced separated flow shock oscillation.

Plotkin, K. J.↗

NASA NTRS1974

Analysis of high-velocity and real-gas effects on the shock-interference pattern for delta-wing orbiters

Numerical solutions have been generated to study the two-dimensional flow field which results when supersonic flow encounters double-wedge configurations whose angles are such that a Type VI pattern occurs. Two numerical codes were developed: one which used the perfect-gas relations (including the ability to vary gamma to 'simulate' real-gas effects) and a second which incorporated a Mollier table to define equilibrium air properties. Theoretical surface-pressure and heat-transfer distributions in the interaction perturbed region along the simulated 'wing-leading edge' were obtained for velocities from 1167 m/sec to 7610 m/sec.

Bertin, J. J.↗

NASA NTRS1984

Effects of tail span and empennage arrangement on drag of a typical single-engine fighter aft end

An investigation was conducted in the Langley 16 foot Transonic Tunnel to determine the effects of tail span and empennage arrangement on drag of a single engine nozzle/afterbody model. Tests were conducted at Mach numbers from 0.50 to 1.20, nozzle pressures frm 1.0 (jet off) to 8.0, and angles of attack from -3 to 9 deg, depending upon Mach numbers. Three empennage arrangements (aft, staggered, and forward) were investigated with several different tail spans. The results of the investigation indicate that tail span and position have a significant effect on the drag at transonic speeds. Unfavorable tail interference was largely due to the outer portion of the tail surfaces. The inner portion near the nozzle and afterbody did little to increase drag other than surface skin friction. Tail positions forward of the nozzle generally had lower tail interference.

Burley, J. R., II↗

NASA NTRS1994

Interfacial force field characterization of a constrained vapor bubble thermosyphon using IAI

The isothermal profiles of the extended meniscus in a quartz cuvette were measured in a gravitational field using IAI (image analyzing interferometer) which is based on computer enhanced video microscopy of the naturally occurring interference fringes. The experimental results for heptane and pentane menisci were analyzed using the extended Young-Laplace Equation. These isothermal results characterized the interfacial force field in-situ at the start of the heat transfer experiments by quantifying the dispersion constant for the specific liquid-solid system. The experimentally obtained values of the disjoining pressures and the dispersion constants are compared to the subsequent non-isothermal experiments because one of the major variables in the heat sink capability of the CVBT is the dispersion constant. In all previous studies of micro heat pipes the value of the dispersion constant has been 'guesstimated'. The major advantages of the current glass cell is the ability to view the extended meniscus at all times. Experimentally, we find that the extended Young-Laplace Equation is an excellent model for for the force field at the solid-liquid vapor interfaces.

Dasgupta, Sunando↗

NASA NTRS1999

Aftbody Closure Effects on the Reference H Configuration at Subsonic and Transonic Speeds

Experience with afterbody closure effects and accompanying test techniques issues on a High Speed Civil Transport (HSCT)-class configuration is described. An experimental data base has been developed which includes force, moment, and surface pressure data for the High Speed Research (HSR) Reference H configuration with a closed afterbody at subsonic and transonic speeds, and with a cylindrical afterbody at transonic and supersonic speeds. A supporting computational study has been performed using the USM3D unstructured Euler solver for the purposes of computational fluid dynamics (CFD) method assessment and model support system interference assessment with a focus on lower blade mount effects on longitudinal data at transonic speeds. Test technique issues related to a lower blade sting mount strategy are described based on experience in the National Transonic Facility (NTF). The assessment and application of the USM3D code to the afterbody/sting interference problem is discussed. Finally, status and plans to address critical test technique issues and for continuation of the computational study are presented.

Wahls, Richard A.↗

NASA NTRS2002

The Influence of Tropospheric Processes in Modeling the Middle Atmosphere with Gravity Waves

Our Numerical Spectral Model (NSM) extends from the ground up into the thermosphere and has a vertical grid point resolution of about 0.5 km to resolve the interactions of gravity waves (GWs) described with Hines' Doppler Spread Parameterization (DSP). This model produces in the stratosphere and mesosphere the major features of QBO, SAO, tides, and planetary waves. The purpose of this paper is to discuss results from an initial study with our 3D model that shows how certain tropospheric processes can affect the dynamics of the middle atmosphere. Under the influence of tropospheric heating, and augmented by GW interactions, two distinct but related processes can be identified. (1) A meridional circulation develops in the stratosphere, with rising motions at low latitudes that are in magnitude comparable to the downward propagation of the QBO. As Dunkerton pointed out, a larger GW source is then required to reproduce the observed QBO, which tends to move us closer to the values recommended for the DSP. This has significant consequences for our model results that describe the upper mesosphere, considering the general importance of GWs for this region and in influencing planetary waves (e.g., 2-day wave) and tides in particular. (2) Tropospheric heating produces zonal jets near the tropopause that are related to latitudinal variations in pressure and reversing temperature variations (resembling the dynamical conditions near the mesopause), which in turn is conducive to generate baroclinic instability. Modeling results show that our ability to generate the QBO critically depends on the magnitude of the temperature reversal that is a measure of this instability. Planetary waves are generated in this process, which can apparently interfere with or augment the GW interactions. As originally demonstrated by Lindzen and Holton, the eastward propagating Kelvin waves and westward propagating Rossby gravity waves (generated by tropospheric convection) can in principle provide the acceleration to influence the QBO, and we were able to confirm this with our 3D model.

Mayr, H. G.↗

DOE OSTI2020

Glass 3D Printing of Microfluidic Pressure Sensor Interrogated by Fiber-Optic Refractometry

This letter reports a novel fused silica microfluidic device with pressure sensing capability that is fabricated by integrated additive and subtractive manufacturing (IASM) method. The sensor consists of a capillary and a 3D printed glass reservoir, where the reservoir volume change under pressure manifests liquid level deviation inside the capillary, thus realizing the conversion between small pressure change into large liquid level variation. Thanks to the design flexibility of this unique IASM method, the proposed microfluidic device is fabricated with liquid-in-glass thermometer configuration, where the reservoir is sealed following a novel 3D printing assisted glass bonding process. And liquid level is interrogated by a fiber-optic sensor based on multimode interference (MMI) effect. This proposed microfluidic device is attractive for chemical and biomedical sensing because it is flexible in design, and maintains good chemical and mechanical stability, and adjustable sensitivity and range.

42 ENGINEERING↗

NASA NTRS1974

Theoretical prediction of thick wing and pylon-fuselage-fanpod-nacelle aerodynamic characteristics at subcritical speeds. Part 1: Theory and results

The theoretical development and the comparison of results with data of a thick wing and pylon-fuselage-fanpod-nacelle analysis are presented. The analysis utilizes potential flow theory to compute the surface velocities and pressures, section lift and center of pressure, and the total configuration lift, moment, and vortex drag. The skin friction drag is also estimated in the analysis. The perturbation velocities induced by the wing and pylon, fuselage and fanpod, and nacelle are represented by source and vortex lattices, quadrilateral vortices, and source frustums, respectively. The strengths of these singularities are solved for simultaneously including all interference effects. The wing and pylon planforms, twists, cambers, and thickness distributions, and the fuselage and fanpod geometries can be arbitrary in shape, provided the surface gradients are smooth. The flow through nacelle is assumed to be axisymmetric. An axisymmetric center engine hub can also be included. The pylon and nacelle can be attached to the wing, fuselage, or fanpod.

Tulinius, J. R.↗

NASA NTRS1986

Operating envelope charts for the Langley 0.3-meter transonic cryogenic wind tunnel

To take full advantage of the unique Reynolds number capabilities of the 0.3-meter Transonic Cryogenic Tunnel (0.3-m TCT) at the NASA Langley Research Center, it was designed to accommodate test sections other than the original, octagonal, three-dimensional test section. A 20- by 60-cm two-dimensional test section was installed in 1976 and was extensively used, primarily for airfoil testing, through the fall of 1984. The tunnel was inactive during 1985 so that a new test section and improved high speed diffuser could be installed in the tunnel circuit. The new test section has solid adaptive top and bottom walls to reduce or eliminate wall interference for two-dimensional testing. The test section is 33- by 33-cm in cross section at the entrance and is 142 cm long. In the planning and running of past airfoil tests in the 0.3-m TCT, the use of operating envelope charts have proven very useful. These charts give the variation of total temperature and pressure with Mach number and Reynolds number. The operating total temperature range of the 0.3-m TCT is from about 78 K to 327 K with total pressures ranging from about 17.5 psia to 88 psia. This report presents the operating envelope charts for the 0.3-m TCT with the adaptive wall tes t section installed. They were all generated based on a 1-foot chord model. The Mach numbers vary from 0.1 to 0.95.

Rallo, R. A.↗

NASA NTRS1956

The proper combination of lift loadings for least drag on a supersonic wing

Lagrange's method of undetermined multipliers is applied to the problem of properly combining lift loadings for the least drag at a given lift on supersonic wings. The method shows the interference drag between the optimum loading and any loading at the same lift coefficient to be constant. This is an integral form of the criterion established by Robert T. Jones for optimum loadings. The best combination of four loadings on a delta wing with subsonic leading edges is calculated as a numerical example. The loadings considered have finite pressures everywhere on the plan form. Through the sweepback range the optimum combination of the four nonsingular loadings has about the same drag coefficient as a flat plate with leading-edge thrust.

Grant, Frederick C↗