Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process heat”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Relative susceptibility of titanium alloys to hot-salt stress-corrosion

Susceptibility of titanium alloys to hot-salt stress-corrosion cracking increased as follows: Ti-2Al-11Sn-5Zr-0.2Si(679), Ti-6Al-2Sn-4Zr-2Mo(6242), Ti-6Al-4V(64), Ti-6Al-4V-3Co(643), Ti-8Al-1Mo-1V(811), and Ti-13V-11Cr-3A1(13-11-3). The Ti-5Al-6Sn-2Zr-1Mo-0.25Si(5621S) alloy was both the least and most susceptible depending on heat treatment. Such rankings can be drastically altered by heat-to-heat and processing variations. Residual compressive stresses and cyclic exposures also reduce susceptibility to stress-corrosion. Simulated turbine-engine compressor environmental variables such as air velocity, pressure, dewpoint, salt concentration, and salt deposition temperature have only minor effects. Detection of substantial concentrations of hydrogen in all corroded alloys confirmed the existence of a hydrogen embrittlement mechanism.

Gray, H. R.↗
NASA NTRS1971

Thermally restorable optical degradation effects in heat-treated Cu2S-CdS crystal heterojunctions.

We have shown that heat treatment alone does not produce appreciable degradation of the short-circuit current in Cu2S-CdS single-crystal photovoltaic heterojunctions. The degradation, which has been commonly observed, is the result of optically induced effects in the heat-treated cell, subsequent to the heat treatment. These optically induced effects can be correlated with photochemical changes induced in single crystals of CdS:Cd:Cu in which the density of Cu acceptors exceeds the density of excess-Cd donors. Major conclusions about the mechanism of the photovoltaic effect and heat-treatment processes can be drawn.

Kanev, S. K.↗
NASA NTRS1972

Solution of the Boltzmann kinetic equation for the relaxation of a gas mixture

The temporal behavior is considered of a quiescent mixture of gases of different temperatures with spatially uniform distribution. The process of heating a cold gas by a hot gas is treated on the basis of the Boltzmann kinetic equation. The mixture is assumed to be composed of absolutely hard smooth spheres, and the initial distribution functions for each gas is taken to the Maxwellian. With such a choice of initial distribution functions, it is shown that the solution of the Boltzmann kinetic equation depends only on the velocity modulus and the time.

Rykov, V. A.↗
NASA NTRS1974

Method of calculating gas dynamics and heat transfer in single stage refrigeration units

A generalized mathematical model of gas-dynamic and heat transfer processes in single-stage regenerative installations operating in Stirling, MacMahon, Gifford-MacMahon, and pulsating tube cycles is proposed. A numerical method os solving initial equations on a digital computer is given. This makes it possible to calculate the change in the thermodynamic parameters in the working cycle in different machine components, as well as the dependence of cold productivity on the temperature level in the steady regime.

Zhitomirskiy, I. S.↗
NASA NTRS1975

Low cost AMOS solar cell development

Recent developments at JPL have demonstrated that high conversion efficiencies are found with GaAs metal semiconductor solar cells when a particular heat treatment processing step is used to introduce an interfacial layer between the metal and the semiconductor. The new cell, called AMOS (Antireflection-Coated Metal-Oxide-Semiconductor), has open circuit voltages of 0.68-0.72 volts and efficiencies of 15% under terrestrial sunlight, as compared to values of 0.45-0.48 volts and 10%, respectively, for similar cells without an interfacial layer. Potentially higher efficiencies are feasible as further improvements are made in optimizing the interfacial layer effect and in increasing the blue response of the cells. A thin film AMOS cell is proposed that uses a thin recrystallized germanium (Ge) layer between a low cost metal substrate and the vapor phase epitaxially (VPE)-grown GaAs.

Stirn, R. J.↗
NASA NTRS1975

Application of thermal scanning to the study of transverse mixing in rivers

Remote sensing has shown itself to be a valuable research tool in the study of transverse mixing in rivers. It is desirable, for a number of reasons, to study and predict the two-dimensional movement of pollutants in the region just downstream of a pollutant discharge point. While many of the more common pollutants do not exhibit a spectral signature, it was shown that the temperature difference between the pollutant and the receiving water could be successfully exploited by applying a mathematical model of mass transport processes to heat transport, and testing and calibrating it with thermal scanning data.

Eheart, J. W.↗
NASA NTRS1977

The jet engine design that can drastically reduce oxides of nitrogen

The NOx pollution problem of hydrogen fueled turbojets and supersonic combustion ramjets (scramjets) was investigated to determine means of substantially alleviating the problem. Since the NOx reaction rates are much slower than the energy producing reactions, the NOx production depends mainly on the maximum local temperatures in the combustor and the NOx concentration is far from equilibrium at the end of a typical combustor (L approximately 1 ft). In diffusion flames, as used in present turbojets and scramjets combustor designs, the maximum local temperature occurs at the flame and is equal to the stoichiometric value. Whereas, in the heat conduction flames, wherein the flame propagates due to a heat conduction process away from the flame to the cooler oncoming premixed unburnt gases, the maximum temperature is lower than in the diffusion flame. Hence the corresponding pollution index is also lower.

Ferri, A.↗
NASA NTRS1977

Mechanical properties of ion-beam-textured surgical implant alloys

An electron-bombardment Hg ion thruster was used as an ion source to texture surfaces of materials used to make orthopedic and/or dental prostheses or implants. The materials textured include 316 stainless steel, titanium-6% aluminum, 4% vanadium, and cobalt-20% chromium, 15% tungsten. To determine the effect of ion texturing on the ultimate strength and yield strength, stainless steel and Co-Cr-W alloy samples were tensile tested to failure. Three types of samples of both materials were tested. One type was ion-textured (the process also heats each sample to 300 C), another type was simply heated to 300 C in an oven, and the third type was untreated. Stress-strain diagrams, 0.2% offset yield strength data, total elongation data, and area reduction data are presented. Fatigue specimens of ion textured and untextured 316 stainless steel and Ti-6% Al-4% V were tested. Included as an ion textured sample is a Ti-6% Al-4% V sample which was ion machined by means of Ni screen mask so as to produce an array of 140 mu m x 140 mu m x 60 mu m deep pits. Scanning electron microscopy was used to characterize the ion textured surfaces.

Weigand, A. J.↗
NASA NTRS1978

Storage systems for solar thermal power

The development status is reviewed of some thermal energy storage technologies specifically oriented towards providing diurnal heat storage for solar central power systems and solar total energy systems. These technologies include sensible heat storage in caverns and latent heat storage using both active and passive heat exchange processes. In addition, selected thermal storage concepts which appear promising to a variety of advanced solar thermal system applications are discussed.

Calogeras, J. E.↗
NASA NTRS1977

Progress in advanced high temperature turbine materials, coatings, and technology

Several NASA-sponsored benefit-cost studies have shown that very substantial benefits can be obtained by increasing material capability for aircraft gas turbines. Prealloyed powder processing holds promise for providing superalloys with increased strength for turbine disk applications. The developement of advanced powder metallurgy disk alloys must be based on a design of optimum processing and heat treating procedures. Materials considered for high temperature application include oxide dispersion strengthened (ODS) alloys, directionally solidified superalloys, ceramics, directionally solidified eutectics, materials combining the high strength of a gamma prime strengthened alloy with the elevated temperature strength of an ODS, and composites. Attention is also given to the use of high pressure turbine seals, approaches for promoting environmental protection, and turbine cooling technology.

Freche, J. C.↗