Search NASA⌕ Search

SEARCH · Search NASA

Results for “REACTOR OPERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Pile noise experiment in MINERVE reactor to estimate kinetic parameters using various data processing methods

MINERVE is a two-zone pool type zero power reactor operated by CEA (Cadarache, France). Kinetic parameters of the core (prompt neutron decay constant, delayed neutron fraction, generation time) have been recently measured using various pile noise experimental techniques, namely Feynman-α, Rossi-α and Cohn-α. Results are discussed and compared to each other's. The measurement campaign has been conducted in the framework of a tri-partite collaboration between CEA, SCK.CEN and PSI. Results presented in this paper were obtained thanks to a time-stamping acquisition system developed by CEA. PSI performed simultaneous measurements which are presented in a companion paper. Signals come from two high efficiency fission chambers located in the graphite reflector next to the core driver zone. Experiments were conducted at critical state with a reactor power of 0.2 W. The core integral fission rate is obtained from a calibrated miniature fission chamber located at the center of the core. Other results obtained in two sub-critical configurations will be presented elsewhere. Best estimate delayed neutron fraction comes from the Cohn-α method: 747 ± 15 pcm (1σ). In this case, the prompt decay constant is 79 ± 0.5 s{sup -1} and the generation time is 94.5 ± 0.7 μs. Other methods give consistent results within the confidence intervals. Experimental results are compared to calculated values obtained from a full 3D core modeling with the CEA-developed Monte Carlo code TRIPOLI4.9 associated with its continuous energy JEFF3.1.1-based library. A very good agreement is observed for the calculated delayed neutron fraction (748.7 ± 0.4 pcm at 1σ), that is a difference of -0.3% with the experiment. On the contrary, a 10% discrepancy is observed for the calculated generation time (104.4 ± 0.1 μs at 1σ). (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Integrating Immersive Visualization in Molten-Salt Reactor Waste Management for Experimental Design and Planning

Molten-salt reactors (MSRs) represent a promising solution for next-generation nuclear energy, offering advantages in safety, fuel efficiency, and waste minimization. However, their liquid-fueled design presents unique challenges for spent fuel management, making post-shutdown waste characterization essential for developing effective strategies. Despite this need, there is a notable absence of visualization platforms specifically tailored to the unique characteristics and analytical requirements of MSR waste management. Existing tools in the nuclear industry are primarily designed for reactor operations or generic data exploration and lack both integration with MSR-specific multiphysics frameworks and the ability to simultaneously visualize time-dependent thermal fields, chemical composition evolution, and radiation distribution patterns. To address these limitations, this paper presents an immersive virtual reality (VR) visualization platform that processes and displays high-fidelity multiphysics simulation output from the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework in real-time, using Unity. The platform visualizes MSR waste characteristics such as nuclide decay, salt cooling, and corrosion by using Exodus II output data and running on a VR headset. It includes a user-friendly interface with features such as visibility toggling, cross-sectional slicing, and time-series animation for exploring simulation data. These capabilities support experimental design, stakeholder engagement, and public communication by making complex reactor behavior more accessible and understandable. By enhancing spatial reasoning and reducing cognitive load, this immersive environment fosters more effective communication and decision-making in MSR waste management.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Intensified biogas to liquid (IBGTL) Process: Experimental validation and modeling analysis

The Intensified Biogas to Liquid (IBGTL) process aims to overcome traditional economy-of-scale barriers in biogas-to-liquid fuel production by integrating bi-reforming and Fischer-Tropsch synthesis (FTS) in a single IBGTL reactor. This reactor operates at uniform pressure with different optimized temperatures across two zones for efficient conversion, utilizing multifunctional bi-reforming catalysts and high-temperature FTS catalysts. Bench scale experiments were carried out using landfill gas (LFG) in a single pass process, and the yield data from these experiments were fed into process scale-up design and techno-economic analysis (TEA) across four scenarios: (1) a single pass process, (2) a process with material recycling, (3) a process with liquefied petroleum gas (LPG) co-product recovery, and (4) a process with electricity generation from the fuel gas produced. TEA identified Scenario 2 as the most cost-effective, achieving a Minimum Fuel Selling Price (MFSP) of $\$4.59$ per gallon, competitive with the current national diesel price of $\$4.7$ per gallon. However, comparison with the conventional two-reactor system highlights the need for catalyst performance improvements. Sensitivity analysis emphasized the importance of manufacturing cost, liquid fuel yield, and biogas flow rate. Further analysis determined that the IBGTL process must achieve a diesel mass yield beyond 11.7% to surpass the economic viability of the conventional TriFTS (Tri-reforming followed by Fischer-Tropsch Synthesis) process. If the IBGTL process attains the TriFTS yield of up to 17%, the resulting MFSP could be approximately 31% lower than the current TriFTS MFSP. Furthermore, renewable energy credits and carbon credits can further enhance the economic viability of BGTL processes.

09 BIOMASS FUELS↗

(Project 14-6770) An Investigation to Establish Multiphysical Property Dataset of Nuclear Materials Based on in-situ Observations and Measurements

In-core nuclear materials including fuel pins and cladding materials fail due to issues including corrosion, mechanical wear, and pellet cladding interaction. In most such scenario microstructure dependent and corrosioninduced chemistry dependent property changes significantly affect performance of cladding, pellet, and housing. Emphasis of this work was on replace conventional pellet-cladding material models with a new straingradient viscoplasticity model that is informed by transmission electron microscopy (TEM) based measurements and by nanomechanical Raman spectroscopy (NMRS) based measurements. The TEM measurements are quantitative in nature and therefore reveal stress-strain relations with simultaneous insights into mechanisms of deformation at nanoscale. The NMRS measurements reveal the similar information at mesoscale along with additional information on relating local microstructural stresses with applied stresses. The resulting information is used to fit constants in the strain gradient viscoplasticity model as well as to validate one. During TEM measurements, a micro-electro-mechanical system based setup was developed with mechanical actuation, sensing, heating, and electrical loading. Contrary to post-mortem analysis or qualitative visualization, this setup combines direct visualization of the mechanisms behind deformation with measurement of stress, strain, thermal and electrical properties. The unique research philosophy of visualizing the microstructure at high resolution while measuring the properties led to fundamental understanding in grain size and temperature effects on measured mechanical properties such as fracture toughness. A key contribution is the role of mechanical loading boundary conditions to deconvolute the insitu TEM based nanoscale and NMRS based mesoscale data to bulk behavior. First the literature based pellet cladding mechanical interaction model based on the work of Retel’s and Williamson’s in literature work to predict tempurature and stress distribution in cladding and pellet at normal operating condition was analyzed. Later the data was fitted to find constants for a viscoplastic strain gradient model. The developed model still needs to be refined and calibrated using various experimental results. That remains the focus of future work. Overall, a major thrust of the work was therefore on active control of the microstructure (grain size, defect density and types) exploiting the multi-physics coupling in materials. In particular, using experiments the synergy of current density, mechanical stress and temperature were studied to annihilate defects and recrystallize grains. The developed model is being examined for implementation in BISON. Multiple invited talks, international journal publications, and conference publications were performed by students supported on this work. Another output is support multiple PhD and masters thesis students who will be an important asset for future basic nuclear research. Future Work Recommendations: A nuclear reactor operates under significant variations of thermal loads due to energy cycling and mechanical loads due to constraint effects. Significant thermal and chemical diffusion takes place at the pallet-cladding level. While the proposed work established new experimental approach and new dataset for Zircaloy-4, the irradiation level was in the range of 1-2 dpa. Samples with higher dpa need to be examined. Therefore, a continual of support of the performed work is essential. Currently, these are the only experiments that can measure the produced data. The work also needs to be extended to different fuel types and cladding types such as SiC and FeCrAl based claddings. A combination of datasets for these materials can then be used to analyze accurately predict behavior of critical pellet cladding systems in accident scenario with high heat flux and high thermal loads. This is a BIG unknown as if now.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multiphysics Coupling Methods for Molten Salt Reactor Modeling and Simulation in VERA

New multiphysics coupling capabilities for molten salt reactor (MSR) analysis have been developed in the Virtual Environment for Reactor Applications (VERA). This development consisted of two main efforts. First, a generic species transport module was added in the CTF code, which is the thermal-hydraulics (TH) code for VERA. This module uses the velocity fields for which CTF solves during the TH calculation to transport species through the core and around the primary loop. Additionally, a gas sparging model has been added to CTF to model the movement of certain species, namely, fission products such as xenon gas, to transport between the molten salt and gas bubbles present in the salt. The second effort in this development was coupling this capability to VERA’s neutron transport code MPACT. This effort focused on coupling the detailed TH transport models in CTF to MPACT to account for feedback effects in the neutron transport calculations. Finally, the thermochemistry code Thermochimica has also been coupled to VERA. Thermochimica performs pointwise calculations for chemical potential and Gibbs free energy and determines what phases are produced by the temperature, pressure, and elemental concentrations at different locations in the primary loop. These capabilities are demonstrated using a model of the Molten Salt Reactor Experiment (MSRE). Furthermore, this reactor operated at Oak Ridge National Laboratory in the 1960s, providing sources of experimental data that were used to develop the model. Various combinations of species were modeled using VERA’s new multiphysics coupling capabilities. Species distributions and reactivity effects behaved as expected for the MSRE model, demonstrating that the coupling is behaving correctly and causing appropriate feedback. The results of these calculations show the potential for VERA to be used for a wide variety of MSR analyses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Solvent selection for a biomass-to-bioproduct pipeline through integrated reductive catalytic fractionation and microbial funneling

The growing significance of lignin-first biorefineries, which focus on upgrading the aromatics resulting from lignin depolymerization, presents opportunities for bioproduct synthesis using microbial strains capable of funneling a diverse array of phenolics into a single commodity chemical. In this study, we evaluated a biomass-to-bioproduct pipeline involving the reductive catalytic fractionation (RCF) of poplar biomass followed by biological funneling with a Novosphingobium aromaticivorans strain that produces 2-pyrone-4,6-dicarboxylic acid (PDC), a potential bioplastic precursor. Considering the impact of solvent on RCF reactor operating pressure, and the potential inhibitory effects of solvent on downstream microbial funneling, we performed an analysis of six pure solvents, namely methanol, ethanol, isopropanol, isobutanol, 1,4-dioxane and ethylene glycol, and different variations of their aqueous mixtures comprising 5 to 50 vol% water. For each pure solvent and solvent/water system, we measured phenolic monomer yields in the RCF process and PDC yields from the phenolic monomers. We then developed correlation models that relate phenolic monomer yields from RCF-derived samples to Hansen solubility parameters to determine solvent descriptors that contribute to high yields. Furthermore, we developed an integrated biorefinery system to estimate the minimum selling price (MSP) of PDC and the associated carbon footprint to identify solvent systems with better costs and sustainability metrics. These analyses resulted in the 50 vol% methanol/water system being identified as optimal because it reduces RCF reactor pressure and is compatible with microbial funneling with N. aromaticivorans. This solvent system produced 63 g PDC per kg biomass (264 g PDC per kg lignin) from 85 g phenolic monomers per kg biomass at a reduced reactor pressure of 48 bar (reduced by 26% compared to our previous poplar-to-PDC pipeline). The MSP for this system is $\$$13.98 per kg of purified PDC (carbon footprint of 1.47 kg CO 2 e per kg), which is about 24% lower than a previously described poplar-to-PDC pipeline and 46% lower than a lignin-to-PDC pipeline that used pure methanol as the solvent. The results from this study illustrate improvements that can be made in lignocellulosic biorefineries that are compatible with the hybrid chemical and biological processes needed to gain value from lignin.

Sripada, Sarada [Great Lakes Bioenergy Research Ce↗

Extended Burnup Credit for BWR Spent Nuclear Fuel in Storage and Transportation Systems

[Full Text] Oak Ridge National Laboratory and the United States Nuclear Regulatory Commission have initiated a multiyear project to investigate the application of burnup credit (BUC) for boiling-water reactor (BWR) fuel in storage and transportation casks. This project includes two phases. The first phase investigates the applicability of peak reactivity methods currently used for spent fuel pools to spent fuel storage and transportation casks and the validation of reactivity (k eff ) calculations and depleted fuel compositions. The second phase focuses on extending BUC beyond peak reactivity. This paper documents work performed to date, investigating some aspects of extended BUC, and it also describes the plan to complete the evaluations. The technical basis for application of peak reactivity methods to BWR fuel in storage and transportation systems is presented in a companion paper. Two reactor operating parameters are being evaluated to establish an adequate basis for extended BWR BUC, including investigation of the axial void profile effect and the effect of control blade utilization during operation. A detailed analysis of core simulator data for one cycle of an operating BWR plant was performed to determine the range of void profiles and the variability of the profile experienced during irradiation. While a single cycle does not provide complete data, the data obtained are sufficient to use to determine the primary effects and identify conservative modeling approaches. Using data resulting from a single cycle, the axial void profile is studied by first determining the temporal fidelity necessary in depletion modeling, and then using multiple void profiles to examine the effect of the void profile on cask reactivity. The results of these studies are being used to develop recommendations for conservatively modeling the void profile effects for BWR depletion calculations. The second operational parameter studied is control blade exposure. Control blades are inserted in various locations and at varying degrees during BWR operation based on the reload design. The presence of control blades during depletion hardens the neutron spectrum locally due to both moderator displacement and introduction of a thermal neutron absorber. The reactivity impact of control blade presence is investigated herein, as well as the effect of multiple (continuous and intermittent) exposure periods. The coupled effects of control blade presence on power density, void profile, or burnup profile have not been considered to date but will be addressed in future work.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Conceptual Design Report for the Xe-6/7/8 Experiment in the NE Flux Trap

X energy, LLC has initiated conceptual design of a high-temperature, pebble-bed reactor and requested that Idaho National Laboratory evaluate the feasibility of irradiating several fuel pebbles in the Advanced Test Reactor. The proposed fuel for the X energy reactor utilizes the same tristructural-isotropic coated fuel particles as are used in the Department of Energy-sponsored Advanced Gas Reactor (AGR) fuel tests, which have been irradiated in the ATR since 2006. The X energy test has been denoted XE 6/7/8 based on nomenclature from the AGR fuel-test series. Three tests will be combined into one test train: XE 6 constitutes the fuel qualification test, whose aim is to demonstrate fuel performance at the upper end of prototypical reactor conditions; XE 7 is designated a “margin test,” and its purpose is to demonstrate fuel integrity at conditions substantially beyond reactor operating conditions; and XE 8 incorporates designed-to-fail particles in order to release fission products and help validate fission product release codes. The XE series of experiments would consist of multiple separate capsules that would be irradiated simultaneously. Each capsule would have its own inert sweep-gas atmosphere with individual on line temperature monitoring. The sweep-gas effluent from each capsule would also have online fission product monitoring to track performance of the fuel in each individual capsule during irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report on FY 2021 testing in support of integrating Alloy 800H and 2.25Cr-1Mo for EPP analysis

The use of simplified Elastic-Perfectly Plastic (EPP) design methods avoids the complexities and limitations of the elastic analysis approach in evaluating strain limits and creep-fatigue damage for Class A metallic coolant boundary components in ASME Boiler and Pressure Vessel Code, Section III, Division 5, Subsection HB, Subpart B. No stress classification and linearization are required in the EPP methods. Further, the strain limits and creep-fatigue damage evaluation procedures based on elastic analysis results were developed for the reactor operating conditions where uncoupled, rate-independent plasticity and stationary creep can be used to approximate the deformation in the component adequately. But at very high temperatures, the deformation is rate-dependent, and it can only be approximated adequately by unified viscoplastic model. Thus, for example, the elastic analysis approach cannot be used to evaluate strain limits and creep-fatigue damage for Alloy 617 above 650 °C. The EPP methods remove the temperature restriction. They can be used to evaluate strain limits and creep-fatigue damage for the full range of temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Nuclear Enterprise Science & Technology (NEST) [Slides]

The NEST Certificate Program is designed to provide students with the skills and experience to qualify for entry-level positions in nuclear facilities as Fissile Material Handler and/or Glovebox Operator. The program goal is to provide for a technically qualified workforce who can execute a variety of programmatic work in modern nuclear materials handling and processing facilities. The program is designed to be completed in a minimum of 1 year (2 semesters) of university level courses (30 credit hours). A certificate will be offered and awarded through the University of New Mexico – Los Alamos (UNM-LA). NEST is unique in that it is an immersive education program. The NNSA-required training for nuclear material handlers and fissionable material handlers has been cross-walked with the educational Core Curricula. Academic content will be delivered that provides background scientific and engineering understanding of the fundamental concepts behind this training. It will be offered as a Pilot Program to an incumbent cohort to ensure that the Certificate meets programmatic needs. NEST is modelled after a Wharton County Junior College (Texas) program to attract and produce nuclear reactor operators.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

Thermal Transport and Fracture Behavior of Sintered Fuel Pellets: Experimental Validation of NEAMS Tool MARMOT

The project targets at experimental validation of NEAMS tool MARMOT for predicting thermal transport and fuel fracture. The key components of the project include: (1) sintering UO 2 samples with well-controlled microstructures (grain size, pore, fission bubble, porosity and pore distribution either in intra- or inter-granular pores); (2) thermal conductivity measurements of these wellcharacterized polycrystalline samples; (3) indentation testing of sintered UO 2 with various grain size, porosity and stoichiometry to obtain fracture and crack propagation mechanisms (inter or intragranular fracture); and (4) validation and uncertainty quantification of the MARMOT thermal transport and fracture models. The high quality experimental data will be used to validate the predictions of MARMOT for thermal transport and fracture, using average data and local microstructure information. In this work, UO 2 fuels with controlled microstructure (grain size, pore size/structure and fuel chemistry) were successfully prepared by high energy ball milling of the hyper-stoichiometric UO 2+x powders purchased commercially, and consolidated by spark plasma sintering. Dense nano-sized UO 2 fuel pellets with controlled stoichiometry were sintered by SPS. The effects of different SPS sintering parameters on the pore size and distribution were investigated, and the correlation among the SPS parameter – microstructure control – stoichiometry/defect structure was established. To further control the pore structure and fuel chemistry, systematic thermal annealing of the sintered fuels with the controlled pore structure was performed in a reduced. The controlled microstructure and fuel chemistry enable the investigation of the separate effects of pore structure and fuel chemistry on thermal transport behavior. The mechanical properties of the sintered UO 2 fuels were tested by nanoindentation and microindentation testing at different temperatures. The fracture behavior of the sintered fuels as functions of grain structure and temperature was investigated. Nanocrystalline UO 2 display higher hardness than microcrystalline counterpart, consistent with the Hall-Petch strengthening mechanism. Greater Young’s modulus and fracture toughness are also identified for the nanocrystalline UO 2 , and hardness and Young’s modulus decrease with temperature, suggesting better ductility of oxide fuels at greater temperature at small length scale. Hyper-stoichiometric UO 2 specimen displays higher hardness and fracture toughness than stoichiometric UO 2 , due to the impediment of the crack propagation by the oxygen interstitial atoms. These results are useful in understanding the mechanical properties of the high burn-up structure (HBS) formed in nuclear fuels during reactor operation, and also provide critical experimental data as the input for the development and validation of the MARMOT fracture model of nuclear fuels. The thermal properties of the sintered UO 2 fuel pellets with controlled grain structure, fuel chemistry and pore structures are measured by laser flash and the impact of the microstructure characteristics on the thermal transport properties is elucidated. Through a close collaboration with the MARMOT team at Idaho National Laboratory, the thermal properties of the sintered oxide fuel pellets with controlled microstructures are measured experimentally, and modeled using the developed MARMOT thermal transport models for a joint effort of demonstrating high spatial resolution measurements at the microstructural level on as-fabricated nuclear fuels and materials and obtain critical experimental data for model validation and properties predictions. In this work, we also conducted sensitivity analysis and uncertainty quantification (UQ) on a mesoscale simulation that has been applied to understand the effective thermal conductivity of UO 2 reactor fuel using the MARMOT tool. We also conduced UQ on mechanistic macroscale models that have been developed to predict the effective thermal conductivity. The most sensitive parameter is the thermal conductivity of bulk UO 2 for the thermal conductivity models. In the future, the predicted simulation distributions need to be compared to experimental data for validation of the models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Regeneration of spent catalysts in oxy-combustion atmosphere

The feasibility of adopting an oxy-combustion stage to regenerate a spent catalyst proposed for methane thermo-catalytic decomposition has been investigated in a laboratory scale bubbling fluidized bed reactor operated at 800 C and different inlet oxygen concentrations. The efficiency of carbon oxy-combustion regeneration strategy has been evaluated on the basis of the efficiency of carbon removed from the catalyst and the performance of regenerated catalyst. The effect of multiple cycles of decomposition and regeneration steps has been also quantified. Experimental activity confirmed the possibility of producing a CO{sub 2} stream that can be finalized to a sequestration unit but also indicated the requirement of a good temperature control of catalytic particles. (author)

08 HYDROGEN↗

Sensitivity analysis for best-estimate thermal models of vertical dry cask storage systems

Loading requirements for dry cask storage of spent nuclear fuel are driven primarily by decay heat capacity limitations, which themselves are determined through recommended limits on peak cladding temperature within the cask. This study examines the relative sensitivity of peak material temperatures within the cask to parameters that influence both the stored fuel residual decay heat as well as heat removal mechanisms. Here, these parameters include the detailed reactor operating history parameters (e.g., soluble boron concentrations and the presence of burnable poisons) as well as factors that influence heat removal, including non-dominant processes (such as conduction from the fuel basket to the canister and radiation within the canister) and ambient environmental conditions. By examining the factors that drive heat removal from the cask alongside well-understood factors that drive decay heat, it is therefore possible to make a contextual analysis of the most important parameters to evaluation of peak material temperatures within the cask.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pilot microbial electrolysis cell closes the hydrogen loop for hydrothermal wet waste conversion to jet fuel

The global shift toward net-zero emissions necessitates resource recovery from wet waste. In this study, we demonstrate the first feasibility of combining pilot-scale microbial electrolytic cells (MECs) with hydrothermal liquefaction (HTL) for simultaneous post-hydrothermal liquefaction wastewater (PHW) treatment and efficient hydrogen (H₂) production to meet biocrude upgrading requirements. Long-term single reactor operation revealed that fixed anode potential enabled rapid startup, and low catholyte pH and high salinity were effective in suppression of cathodic methanogenesis and acetogenesis – resulting in high current density of 16.6 A m –2 and 9.3 A m –2 when feeding synthetic wastewater and PHW respectively. Additionally, the anode biofilm exhibited spatial variations in response to local environmental conditions. In conclusion, onsite parallel or serial operations of multiple MECs showed good performance using actual PHW with a record-high H 2 production rate of 0.5 L L R day –1 for MEC over 10 liters scale, and the optimal chemical oxygen demand (COD)-to-H 2 yield reached 0.127 kg-H 2 per kg-COD, supporting a self-sufficient, closed-loop upgrade to jet fuel.

08 HYDROGEN↗

Effect of Light Water Reactor Water Environments on the Fatigue Life of Reactor Materials

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (Code) provides rules for the design of Class 1 components of nuclear power plants. Figures I-9.1 through I-9.6 of Appendix I to Section III of the Code specify fatigue design curves for applicable structural materials. However, the Code design curves do not explicitly address the effects of light water reactor (LWR) water environments. Existing fatigue strain-vs.-life (ε-N) laboratory data illustrate potentially significant effects of LWR water environments on the fatigue resistance of pressure vessel and piping steels. Extensive studies have been conducted at Argonne National Laboratory and elsewhere since 1990 to investigate the effects of LWR environments on the fatigue life of piping and pressure vessel steels. This article summarizes the results of these studies. Existing fatigue ε-N data were evaluated to identify the various material, environmental, and loading conditions that influence fatigue crack initiation; a methodology for estimating fatigue lives as a function of these parameters was developed. The effects were incorporated into the ASME Code Section III fatigue evaluations in terms of an environmental correction factor, F en , which is defined as the ratio of fatigue life in air at room temperature to the fatigue life in the LWR water environment at reactor operating temperatures. Available fatigue data were used to develop fatigue design curves for carbon and low-alloy steels, austenitic stainless steels, and nickel-chromium-iron (NiCr-Fe) alloys and their weld metals in air at room temperature. A review of the Code Section III fatigue adjustment factors of 2 on strain and 20 on life is also presented and the possible conservatism inherent in the choice of these adjustment factors is evaluated. A brief description of potential effects of neutron irradiation on fatigue crack initiation for these structural materials is also presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Subchannel analysis on CGNPC SCWR

SCWR, as one of the candidates of six generation 4 reactors, is the water cooled reactor operating above the critical point. The investigation on SCWR was popular worldwide and amount of concepts were proposed by different country. Chinese Guangdong Nuclear Power Company (CGNPC) also designed a SCWR based on the Double-row Assembly. Based on the power distribution in different stage of the fuel cycle obtained by neutronics physics, the first pass and the second pass were calculated using ATHAS code, respectively, and the maximum cladding temperatures were obtained, which was satisfied the design limitation. The sensitivity of the geometry parameters was analyzed, and the optimum on the assembly design was carried. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Preliminary studies on diversion and misuse for TRISO-fueled heat-pipe-cooled microreactors

Microreactors are being developed by multiple reactor designers to mass-produce nuclear facilities for worldwide deployment. Including microreactors in a country’s energy portfolio introduces new concerns for international safeguards regarding the number of reactor locations. Microreactors have smaller quantities of nuclear material compared to current light-water reactors, which makes diverting enough material for clandestine purposes difficult for a single reactor. Diversion or misuse of multiple microreactors to obtain a significant quantity introduces a new acquisition pathway. This work examines diversion and misuse scenarios for a realistic heat-pipe-cooled microreactor to understand how these scenarios would effect reactor operations to determine if monitoring key parameters could reduce the burden of inspection on monitoring agencies. Here, we determined misuse caused too drastic of an effect on core operations to be a valid acquisition pathway for the realistic heat-pipe-cooled microreactor. Diversion was explored across varying levels of severity, where potential diversion scenarios could yield one significant quantity of material from between six and eleven microreactors. Through examining the critical control drum angle, excess reactivity, control drum worth, and power distribution changes from nominal were detected over the operational lifetime, which could indicate a divergence from normal operations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Physics-Based Multi-State Models of Passive Component Degradation for the R7 Reactor Simulation Environment

Abstract: The Next Generation Systems Analysis Code - referred to as R7 - is reactor systems simulation software being developed to support the Risk-Informed Safety Margin Characterization Pathway of the U.S. Department of Energy's Light Water Reactor Sustainability Program. It will provide an integrated multi-physics environment, implemented in an uncertainty quantification (UQ) framework that can produce risk and other performance insights on long-term reactor operations. An element of this simulation environment will be the performance of passive components and materials. Conventional models of component reliability are largely parametric, relying on plant service data to estimate component lifetimes and failure rates. This type of model has limited usefulness in the R7 environment where the intent is to explicitly determine the influence of physical stressors on component degradation. In this paper, we describe a new class of multi-state physics-based component models designed to be R7-compatible. These models capture the physics of materials degradation while also incorporating the effects of interventions and component rejuvenation. The models are implemented in a cumulative damage framework that allows the impact of an evolving physical environment to be addressed without recourse to resampling within the Monte Carlo-based UQ framework. The paper describes an application to stress corrosion cracking in dissimilar metal welds - a principal contributor to potential loss of coolant accidents. So while R7 will have the more conventional capability of reactor simulation codes to model the impact of degraded components and systems on plant performance, the methodology described here allows R7 to model the inverse effect; the impact of the physical environment on component degradation and performance.

PRA, passive components, stress corrosion cracking↗