Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLIDING CONTACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Regimes of traction in concentrated contact lubrication

Experimental evidence is presented for the existence of three regimes of traction in concentrated contacts. Data are obtained in a rolling contact simulator by varying the lubricant, temperature, rolling speed, load and surface roughness at a fixed slide-to-roll ratio. At lower thicknesses the mixed regime is encountered, and traction is increased due to asperity interaction, while at higher film thicknesses, the lubricant pressure is distributed over a greater area than the Hertzian region, resulting in a lower average pressure and reduced traction.

Bair, S.↗

Belleville Spring/Seal

Metallic seal for cavity openings in liquid-nitrogen environments uses Belleville-spring preloaded washer. Due to preloading, Belleville spring/ seal washers slide and deflect to accept radial and axial movement between two sealing surfaces while remaining in sealing contact.

Bradley, D. P.↗

Oxygen and sulfur interactions with a clean iron surface and the effect of rubbing contact on these interactions

The interaction of sulfur and oxygen with an iron surface was studied with Auger spectroscopy analysis both statically and during sliding-friction experiments in a vacuum environment. Oxygen, hydrogen sulfide, methyl mercaptan, and sulfur dioxide were adsorbed to an iron surface. Results indicate that sulfide films formed on clean iron surfaces are completely displaced by oxygen. Hydrocarbons containing sulfur, such as methyl mercaptan, adsorb dissociatively. Less sulfur is adsorbed during sliding with hydrogen sulfide and methyl mercaptan than in the absence of sliding. With both oxygen and sulfur dioxide, sliding did not affect the amount of material adsorbed to iron.

Buckley, D. H.↗

Friction and fracture of single-crystal silicon carbide in contact with itself and titanium

An investigation was conducted to examine the friction properties and mechanical behavior of single-crystal silicon carbide (0001) surface sliding against itself and against polycrystalline titanium. The results indicate hexagon-shaped pits of silicon carbide and the formation of platelet hexagon-shaped wear debris of silicon carbide due to cleavages of both prismatic and basal planes as a result of silicon carbide sliding against itself. The fracturing of silicon carbide also occurs near the adhesive bond to titanium. The wear debris produced by brittle fracture plows the titanium and transfers to it. Further, the silicon carbide wear debris, which adhered and transferred to titanium, plows the silicon carbide surface and transfers back to it

Miyoshi, K.↗

Characterization of microscale wear in a ploysilicon-based MEMS device using AFM and PEEM-NEXAFS spectromicroscopy.

Mechanisms of microscale wear in silicon-based microelectromechanical systems (MEMS) are elucidated by studying a polysilicon nanotractor, a device specifically designed to conduct friction and wear tests under controlled conditions. Photoelectron emission microscopy (PEEM) was combined with near-edge X-ray absorption fine structure (NEXAFS) spectroscopy and atomic force microscopy (AFM) to quantitatively probe chemical changes and structural modification, respectively, in the wear track of the nanotractor. The ability of PEEM-NEXAFS to spatially map chemical variations in the near-surface region of samples at high lateral spatial resolution is unparalleled and therefore ideally suited for this study. The results show that it is possible to detect microscopic chemical changes using PEEM-NEXAFS, specifically, oxidation at the sliding interface of a MEMS device. We observe that wear induces oxidation of the polysilicon at the immediate contact interface, and the spectra are consistent with those from amorphous SiO{sub 2}. The oxidation is correlated with gouging and debris build-up in the wear track, as measured by AFM and scanning electron microscopy (SEM).

36 MATERIALS SCIENCE↗

Ultrasound Evaluation of the Magnitude of Pneumothorax: A New Concept

Pneumothorax is commonly seen in trauma patients; the diagnosis is usually confirmed by radiography. Use of ultrasound for this purpose, in environments such as space flight and remote terrestrial areas where radiographic capabilities are absent, is being investigated by NASA. In this study, the ability of ultrasound to assess the magnitude of pneumothorax in a porcine model was evaluated. Sonography was performed on anesthetized pigs (avg. wt. 50 kg) in both ground-based laboratory (n = 5) and micro gravity conditions (0 g) aboard the KC-135 aircraft during parabolic flight (n = 4). Aliquots of air (50-1 OOcc) were introduced into the chest through a catheter to simulate pneumothorax. Results were video-recorded and digitized for later interpretation by radiologists. Several distinct sonographic patterns of partial lung sliding were noted, including the combination of a sliding zone with a still zone, and a "segmented" sliding zone. These "partial lung sliding" patterns exclude massive pneumothorax manifested by a complete separation of the lung from the parietal pleura. In 0 g, the sonographic picture was more diverse; 1 g differences between posterior and anterior aspects were diminished. CONCLUSIONS: Modest pneumothorax can be inferred by the ultrasound sign of "partial lung sliding". This finding, which increases the negative predictive value of thoracic ultrasound, may be attributed to intermittent pleural contact, small air spaces, or alterations in pleural lubricant. Further studies of these phenomena are warranted.

Sargsyan, Ashot E.↗

Parabolic Flight Testing of Aeroponic Plant Growth Systems and Super Omniphobic Surface Coatings

The purpose of this project is to gain valuable data from three separate experiments. One being an aeroponics watering system, another being a PONDS passive watering system, and the last a super omniphobic surface coating apparatus.There are two aeroponics watering systems that feed water and nutrients to "plant roots" inside of a contained box. The walls inside of the contained boxes have different surface textures and shapes but each contain the same nozzle and compressor set up as a control.There is one PONDS passive watering system that feeds water from a reservoir to a porous substrate utilizing wicking materials. There is one super omniphobic surface coating apparatus that feeds water into an apparatus allowing the water to make contact with three individual compartments in which glass beads with different coatings are carefully placed between two glass slides. The outcome will contribute to the advancement in self sustainment for space exploration. The status of the project when I started was to get the system built and ready for flight come November. My intended contributions are to assist with the build of the system.

Blockey, Jamie Lynn↗

Approaches for Achieving Superlubricity in Two-Dimensional Materials

Controlling friction and reducing wear of moving mechanical systems is important in many applications, from nanoscale electromechanical systems to large-scale car engines and wind turbines. Accordingly, multiple efforts are dedicated to design materials and surfaces for efficient friction and wear manipulation. Recent advances in two-dimensional (2D) materials, such as graphene, hexagonal boron nitride, molybdenum disulfide, and other 2D materials opened an era for conformal, atomically thin solid lubricants. However, the process of effectively incorporating 2D films requires a fundamental understanding of the atomistic origins of friction. In this review, we outline basic mechanisms for frictional energy dissipation during sliding of two surfaces against each other, and the procedures for manipulating friction and wear by introducing 2D materials at the tribological interface. Lastly, we highlight recent progress in implementing 2D materials for friction reduction to near-zero values-superlubricity-across scales from nano- up to macroscale contacts.

2D materials↗

Time-resolved measurements of liquid–vapor thermal interactions throughout the full life-cycle of sliding bubbles at subcooled flow boiling conditions

The local thermal response of the liquid phase to the presence of sliding bubbles was measured with an infrared camera in subcooled flow-boiling conditions. These measurements were complemented with two high-speed cameras to capture the corresponding bubbles’ dynamics. The liquid–vapor interactions were captured in detail over the full life-cycle of sliding bubbles. Four distinctive phases for the bubble life-cycle were identified: A) Spherical bubble growth with strong attachment, B) Deformed bubble growth with weak attachment, C) Detachment with hot liquid quenching, and D) Cold liquid quenching. Here, to the best of the authors’ knowledge, it is the first time that the “detachment with hot liquid quenching phase has been observed. This phase is characterized by a “hot” thermal footprint during the bubble detachment process. It is believed that this footprint is constituted partially from hot liquid released during the condensation of the recently detached bubble, and from released hot fluid previously collected by the bubble during sliding. In addition, this work reveals that using traditional high-speed visualization techniques (side-view camera only) can lead to an underestimation of approximately 40% of the actual bubble–wall contact diameter (dc) which was inferred from the infrared camera measurements.

42 ENGINEERING↗

Structurally Driven Environmental Degradation of Friction in MoS2 Films

Abstract We report an investigation of the friction mechanisms of MoS 2 thin films under changing environments and contact conditions using a variety of computational and experimental techniques. Molecular dynamics simulations were used to study the effects of water and molecular oxygen on friction and bonding of MoS 2 lamellae during initial sliding. Characterization via photoelectron emission microscopy (PEEM) and Kelvin probe force microscopy (KPFM) were used to determine work function changes in shear modified material within the top few nanometers of MoS 2 wear scars. The work function was shown to change with contact conditions and environment, and shown by density functional theory (DFT) calculations and literature reports to be correlated with lamellae size and thickness of the basally oriented surface layer. Results from nanoscale simulations and macroscale experiments suggest that the evolution of the friction behavior of MoS 2 is linked primarily to the formation or inhibition of a basally oriented, molecularly thin surface film with long-range order.

Curry, John F.↗

EFFECTS OF GEOMETRICAL AND MECHANICAL PROPERTIES OF VARIOUS COMPONENTS ON STRESSES OF THE SEALS IN SOFCS

In this paper, numerical modeling was used to understand of the effect of the geometry and mechanical properties of various components in SOFCs on the level and distribution of stresses in the stack during operating and cooling. The results of these modeling analyses will help stack designers reduce high stresses in the seals of the stack so that structural failures are prevented and high stack mechanical reliability is achieved to meet technical targets. In general, it was found that the load carrying capacity of the cathode contact layer was advantageous for reducing the transmitted loads on the cell perimeter seal under operating environments of SOFCs, but the amount of reduction depends upon the relative stiffness values of the cell, interconnect, porous media, and support structures. Comparison of a fully bonded interface to a frictionless sliding interface resulted in 30-50% less transmitted load through the perimeter seal, with the greater reductions due to stiffer contact/media/interconnect structures. These results demonstrate that the mechanical contribution of the contact layer can be substantial and warrant design consideration

30 DIRECT ENERGY CONVERSION↗

Coupled strain-induced alpha to omega phase transformation and plastic flow in zirconium under high pressure torsion in a rotational diamond anvil cell

Strain-induced α → ω phase transformation (PT) in the zirconium (Zr) sample under compression and plastic shear in a rotational diamond anvil cell (RDAC) is investigated using the finite element method (FEM). The fields of the volume fraction of the ω phase, all components of the stress tensor, and plastic strain are presented. Before torsion, PT barely occurs. During torsion under a fixed applied force, PT initiates at the center of the sample, where the pressure first reaches the minimum pressure for strain-induced α → ω PT, p d ε , and propagates from the center to the periphery and from the symmetry plane to the contact surface. Salient increase of the shear friction stress and pressure at the center of a sample, so-called pressure self-multiplication effect observed experimentally for some other materials, is predicted here for Zr. It is caused by much higher yield strength of the phase in comparison with the phase. Except at the very center of a sample, the total contact friction stress is equal to the yield strength in shear of the mixture of phases and the plastic sliding occurs there. Due to the reduction in sample thickness and radial material flow during torsion, the ω phase can be observed in the region where pressure is lower than p d ε , which may lead to misinterpretation of the experimental data for p d ε . For the same applied force, torsion drastically promotes PT in comparison with the compression without torsion. However, the PT process in RDAC is far from optimal: (a) due to the pressure self-multiplication effect, the pressure in the transformed region is much higher than that required for PT; (b) the region in which PT occurs is limited by the pressure p d ε and cannot be expanded by increasing a shear under a fixed force; and (c) the significant reduction in thickness during torsion reduces the total mass of the high-pressure phase. These drawbacks can be overcome by placing a sample within a strong gasket with an optimized geometry. It is shown that, due to strong pressure heterogeneity, characterization of α → ω and α → β PTs based on the averaged pressure contains large errors. Furthermore, the obtained results, in addition to providing an improved understanding of the strain-induced PTs, may be beneficial for the optimum design of experiments and the extraction of material parameters, as well as optimization and control of PTs by varying the geometry and loading conditions.

36 MATERIALS SCIENCE↗

Laser Ablation Sampling of Materials Directly into the Formed Liquid Microjunction of a Continuous Flow Surface Sampling Probe/Electrospray Ionization Emitter for Mass Spectral Analysis and Imaging

Transmission geometry laser ablation directly into a formed liquid microjunction of a continuous flow liquid microjunction surface sampling probe/electrospray ionization emitter was utilized for molecular and elemental detection and mass spectrometry imaging. The ability to efficiently capture and ionize ablated material was demonstrated by the detection of various small soluble n-mers of polyaniline and silver ion solvent clusters formed from laser ablation of electropolymerized polyaniline and silver thin films, respectively. In addition, analysis of surfaces that contain soluble components was accomplished by coating or laminating the sample with an insoluble film to enable liquid junction formation without directly extracting material from the surface. The ability to perform mass spectrometry imaging at a spatial resolution of about 50 m was illustrated by using laminated inked patterns on a microscope slide. In general, these data demonstrate at least an order of magnitude signal enhancement compared to the non-contact, laser ablation droplet capture-based surface sampling/ionization approaches that have been previously presented.

electrospray ionization (ESI)↗

Diffusion and Deformation Mechanism Maps in Li Metal from Atomistic Simulations

The rate of Li transport in the Li metal anode is important for the operation of Li metal-solid state batteries. Here, transport rates due to diffusion and creep are predicted in Li using atomistic simulations. First, molecular dynamics is used to estimate the rate of Li diffusion along dislocations and in grain boundary triple junctions. By combining this data with that from a prior study of grain boundary diffusion the dominant mechanisms and rates of self-diffusion in Li polycrystals are predicted as a function of grain size, grain shape, dislocation density, and temperature. Second, the dominant creep mechanisms are predicted and used to estimate critical current densities and void annihilation times. Grain boundary sliding and coble creep are the dominant mechanisms for micron-sized grains. Lastly, a continuum model for interfacial contact loss reveals that high dislocation densities of ∼10 12 /cm 2 enable achieving battery performance targets for Li grain sizes of ∼10 μm.

Batteries↗

Relation between interfacial shear and friction force in 2D materials

Understanding the interfacial properties between an atomic layer and its substrate is of key interest at both the fundamental and technological levels. From Fermi level pinning to strain engineering and superlubricity, the interaction between a single atomic layer and its substrate governs electronic, mechanical and chemical properties. Here, we measure the hardly accessible interfacial transverse shear modulus of an atomic layer on a substrate. By performing measurements on bulk graphite, and on epitaxial graphene films on SiC with different stacking orders and twisting, as well as in the presence of intercalated hydrogen, we find that the interfacial transverse shear modulus is critically controlled by the stacking order and the atomic layer–substrate interaction. Importantly, we demonstrate that this modulus is a pivotal measurable property to control and predict sliding friction in supported two-dimensional materials. The experiments demonstrate a reciprocal relationship between friction force per unit contact area and interfacial shear modulus. As a result, the same relationship emerges from simulations with simple friction models, where the atomic layer– substrate interaction controls the shear stiffness and therefore the resulting friction dissipation.

36 MATERIALS SCIENCE↗

Friction and hardness of gold films deposited by ion plating and evaporation

Sliding friction experiments were conducted with ion-plated and vapor-deposited gold films on various substrates in contact with a 0.025-mm-radius spherical silicon carbide rider in mineral oil. Hardness measurements were also made to examine the hardness depth profile of the coated gold on the substrate. The results indicate that the hardness is influenced by the depth of the gold coating from the surface. The hardness increases with an increase in the depth. The hardness is also related to the composition gradient in the graded interface between the gold coating and the substrate. The graded interface exhibited the highest hardness resulting from an alloy hardening effect. The coefficient of friction is inversely related to the hardness, namely, the load carrying capacity of the surface. The greater the hardness that the metal surface possesses, the lower is the coefficient of friction. The graded interface exhibited the lowest coefficient of friction.

Miyoshi, K.↗

Effects of wear on structure-sensitive magnetic properties of ceramic ferrite in contact with magnetic tape

Wear experiments and electron microscopy and diffraction studies were conducted to examine the wear and deformed layers in single-crystal Mn-Zn (ceramic) ferrite magnetic head material in contact with magnetic tape and the effects of that contact on magnetic properties. The crystalline state of the single-crystal magnetic head was changed drastically during the sliding process. A nearly amorphous structure was produced on its wear surface. Deformation in the surficial layer of the magnetic head was a critical factor in readback signal loss above 2.5 dB. The signal output level was reduced as applied normal load was increased. Considerable plastic flow occurred on the magnetic tape surface with sliding, and the signal loss due to the tape wear was approximately 1 dB.

Miyoshi, K.↗

Wear reduction in ceramic bearings by surface generated pyrolytic carbon continuously replenished by ethylene gas

Sliding tests with a pin-on-disc tribometer and both sliding and rolling tests with a modified four-ball tester at bulk temperatures of about 500 C and contact pressures of about 2.2 GPa have demonstrated up to 80% reductions of friction and wear with silicon nitride surfaces when a stream of ethylene is directed into the conjunction region. The effects are even more pronounced when the ethylene is prenucleated by a flow over a coil of nichrome wire electrically heated to about 800 C and located about 30 cm upstream of the exit nozzle. Steel and Ni-plated steel are lubricated by this method even more efficiently at lower temperatures.

Lauer, J. L.↗