Search NASA⌕ Search

SEARCH · Search NASA

Results for “Space simulators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Space station Simulation Computer System (SCS) study for NASA/MSFC. Volume 2: Concept document

The Simulation Computer System (SCS) concept document describes and establishes requirements for the functional performance of the SCS system, including interface, logistic, and qualification requirements. The SCS is the computational communications and display segment of the Marshall Space Flight Center (MSFC) Payload Training Complex (PTC). The PTC is the MSFC facility that will train onboard and ground operations personnel to operate the payloads and experiments on board the international Space Station Freedom. The requirements to be satisfied by the system implementation are identified here. The SCS concept document defines the requirements to be satisfied through the implementation of the system capability. The information provides the operational basis for defining the requirements to be allocated to the system components and enables the system organization to assess whether or not the completed system complies with the requirements of the system.

Source record↗

New technique for oil backstreaming contamination measurements

Due to the large size and the number of diffusion pumps, space simulation chambers cannot be easily calibrated by the usual test dome method for measuring backstreaming from oil diffusion pumps. In addition, location dependent contamination may be an important parameter of the test. The backstreaming contamination in the Space Power Facility (SPF) near Sandusky, Ohio, the largest space simulation vacuum test chamber in the U.S.A. was measured. Small size clean silicon wafers as contamination sensors placed at all desired measurement sites were used. The facility used diffusion pumps with DC 705 oil. The thickness of the contamination oil film was measured using ellipsometry. Since the oil did not wet uniformly the silicon substrate, two analysis models were developed to measure the oil film: continuous, homogeneous film and islands of oil with the islands varying in coverage fraction and height. In both cases, the contamination film refractive index was assumed to be that of DC 705. The second model improved the ellipsometric analysis quality parameter by up to two orders of magnitude, especially for the low coverage cases. Comparison of the two models for our case shows that the continuous film model overestimates the oil volume by less than 50 percent. Absolute numbers for backstreaming are in good agreement with published results for diffusion pumps. Good agreement was also found between the ellipsometric results and measurements done by x ray photoelectron spectroscopy (XPS) and by scanning electron microscopy (SEM) on samples exposed to the same vacuum runs.

Alterovitz, S. A.↗

Neutral buoyancy simulation of space telerobotics operations

A number of neutral buoyancy versions of space telerobots have been tested in the Space Research Laboratory to understand the potential roles for telerobotic systems in space operations. Particular attention is given to details of the well-modeled dynamic environment, the existence of sizable data base on EVA operations in neural buoyancy with correlation to flight experience, and routine access to a number of high-fidelity mockups of past and planned operational spacecraft. The compromises necessary for the design and construction of neutral buoyancy telerobotic systems are discussed, and data from a number of past simulations, including correlation of neutral buoyancy structural assembly with EVA flight data, and preliminary tests of telerobotic servicing of Hubble Space Telescope are summarized.

Akin, David L.↗

Simulation of space radiation effects on polyimide film materials for high temperature applications

Space environment effects on candidate materials for the solar sail film are determined. Polymers, including metallized polyimides that might be suitable solar radiation receivers, were exposed to combined proton and solar electromagnetic radiation. Each test sample was weighted, to simulate the tension on the polymer when it is stretched into near-planar shape while receiving solar radiation. Exposure rates up to 16 times that expected in Earth orbit were employed, to simulate near-sun solar sailing conditions. Sample appearance, elongation, and shrinkage were monitored, noted, and documented in situ. Thermosetting polyimides showed less degradation or visual change in appearance than thermoplastics.

Fogdall, L. B.↗

A new technique for oil backstreaming contamination measurements

Due to the large size and the number of diffusion pumps, space simulation chambers cannot be easily calibrated by the usual test dome method for measuring backstreaming from oil diffusion pumps. In addition, location dependent contamination may be an important parameter of the test. The backstreaming contamination was measured in the Space Power Facility (SPF) near Sandusky, OH, the largest space simulation vacuum test chamber in the U.S.. Small clean silicon wafers placed at all desired measurement sites were used as contamination sensors. The facility used diffusion pumps with DC 705 oil. The thickness of the contamination oil film was measured using ellipsometry. Since the oil did not wet the silicon substrate uniformly, two analysis models were developed to measure the oil film: (1) continuous, homogeneous film; and (2) islands of oil with the islands varying in coverage fraction and height. In both cases, the contamination film refractive index was assumed to be that of DC 705. The second model improved the ellipsometric analysis quality parameter by up to two orders of magnitude, especially for the low coverage cases. Comparison of the two models shows that the continuous film model overestimates the oil volume by less than 50 percent. Absolute numbers for backstreaming are in good agreement with published results for diffusion pumps. Good agreement was also found between the ellipsometric results and measurements done by x-ray photoelectron spectroscopy (XPS) and by scanning electron microscopy (SEM) on examples exposed to the same vacuum runs.

Alterovitz, S. A.↗

OVERFLOW Simulations of Space Shuttle Orbiter Reentry Based on As-Built Geometry

The Space Shuttle Orbiters Discovery and Endeavor have been digitally scanned to obtain outer mold line surfaces. Using these scans, the existing overset computational fluid dynamics (CFD) grid system will be modified by projecting the grid points to the scanned geometry. Simulations will be performed using the OVERFLOW solver and the results compared to previous OVERFLOW results on the theoretical geometry and the aerodynamic databook. The "bent airframe" term will be compared between the aerodynamic databook and the computations over a range of reentry conditions.

Ma, Edward C.↗

Ground Testing of an Oxygen Concentrator in a Simulated International Space Station (ISS) Cabin Environment

The method for supplying medical oxygen to respiratorily-compromised astronauts on the International Space Station (ISS) and in future Orion missions consists of drawing oxygen from high pressure oxygen tanks. An Oxygen Concentrator Module (OCM) is a device that pulls in ambient air and separates out the nitrogen, resulting in a high concentration oxygen source. This technology has the potential to eliminate resupply and oxygen-enrichment issues associated with using high pressure oxygen tanks and become an alternative technology to support medical oxygen operations for future exploration missions. In this study, we test the long-term performance of a Commercial Off-the-Shelf (COTS) OCM in a simulated ISS cabin environment. Humidified air, carbon dioxide, and fifteen representative trace contaminants are continuously injected through an enclosed test chamber where the OCM is challenged. This study included the first successful demonstration of the Trace Gas Injection System (TGIS), which reliably and continuously produced ISS levels of trace contaminants, carbon dioxide, and humidity in an enclosed environment. The TGIS is a new and unique ground capability with significant implications for Test Readiness Level (TRL) advancement of COTS items and Government Furnished Equipment (GFE). This study demonstrated that the tested OCM reliably delivers enriched oxygen mostly at desired performance specifications. This study also demonstrated that the OCM does not inadvertently concentrate trace gases in its oxygen product stream, as detectable concentrations of trace contaminants in the oxygen product stream were at all times below the simulated ISS levels.

medical oxygen↗

Credibility Assessment of Deterministic Computational Models and Simulations for Space Biomedical Research and Operations

Human missions beyond low earth orbit to destinations, such as to Mars and asteroids will expose astronauts to novel operational conditions that may pose health risks that are currently not well understood and perhaps unanticipated. In addition, there are limited clinical and research data to inform development and implementation of health risk countermeasures for these missions. Consequently, NASA's Digital Astronaut Project (DAP) is working to develop and implement computational models and simulations (M&S) to help predict and assess spaceflight health and performance risks, and enhance countermeasure development. In order to effectively accomplish these goals, the DAP evaluates its models and simulations via a rigorous verification, validation and credibility assessment process to ensure that the computational tools are sufficiently reliable to both inform research intended to mitigate potential risk as well as guide countermeasure development. In doing so, DAP works closely with end-users, such as space life science researchers, to establish appropriate M&S credibility thresholds. We will present and demonstrate the process the DAP uses to vet computational M&S for space biomedical analysis using real M&S examples. We will also provide recommendations on how the larger space biomedical community can employ these concepts to enhance the credibility of their M&S codes.

Mulugeta, Lealem↗

Overview of the MISSE-16 Mission and Preliminary Characterization of Novel Space Weathered Materials

The Materials International Space Station Experiment (MISSE) project is a series of experiments that began in 2001, involving the deployment of external experiment platforms on the International Space Station (ISS). Since then, more than 4,000 materials were tested yielding valuable data and insights into the performance of materials and coatings in the harsh space environment, as well as providing a platform for testing and validating new materials and technologies. The results of the MISSE experiments have contributed to the development of more durable and reliable spacecraft and equipment, as well as improving our understanding of the space environment and its effects on human space exploration. To gain deeper insights into the changes in material properties of both novel and heritage spacecraft materials over the course of a mission, we proposed to enhance the MISSE hardware. This was achieved by integrating a high-resolution camera that can capture both RGB and IR color data, along with an updated illumination scheme. The identical sets of selected materials were mounted on the Zenith, Ram, and Wake faces of the ISS to expose them to predominant vacuum ultraviolet (VUV), atomic oxygen, and high-energy electron conditions. In addition, we exposed flight duplicates of these materials to a simulated space environment, which included sequential exposure to the same irradiation species on the ground. This allowed us to study the effects of space exposure on the materials in a controlled manner and to compare their behavior in both real and simulated space environments. The MISSE-FF flight sample collection comprised different classes of polymers, including polyimides from the Kapton family, manufactured by E.I du Pont de Nemours and Co., Polyethylene terephthalate (PET) materials, liquid crystal polymers, PI/Polyhedral Oligomeric Silsesquioxanes (POSS), and carbon and glass fiber reinforced polymers. The experimental cadence during the MISSE-16 mission (~6 months) included daily images of each sample for the first week, weekly for the next 2 months, and monthly the remaining duration of the mission. This paper will focus on the flight duplicate as well as the postflight optical characterization of novel and heritage materials currently under observation on the MISSE-FF.

Jainisha R Shah↗

Command and Control of Space Assets Through Internet-Based Technologies Demonstrated

The NASA Glenn Research Center successfully demonstrated a transmission-control-protocol/ Internet-protocol- (TCP/IP) based approach to the command and control of onorbit assets over a secure network. This is a significant accomplishment because future NASA missions will benefit by using Internet-standards-based protocols. Benefits of this Internet-based space command and control system architecture include reduced mission costs and increased mission efficiency. The demonstration proved that this communications architecture is viable for future NASA missions. This demonstration was a significant feat involving multiple NASA organizations and industry. Phillip Paulsen, from Glenn's Project Development and Integration Office, served as the overall project lead, and David Foltz, from Glenn's Satellite Networks and Architectures Branch, provided the hybrid networking support for the required Internet connections. The goal was to build a network that would emulate a connection between a space experiment on the International Space Station and a researcher accessing the experiment from anywhere on the Internet, as shown. The experiment was interfaced to a wireless 802.11 network inside the demonstration area. The wireless link provided connectivity to the Tracking and Data Relay Satellite System (TDRSS) Internet Link Terminal (TILT) satellite uplink terminal located 300 ft away in a parking lot on top of a panel van. TILT provided a crucial link in this demonstration. Leslie Ambrose, NASA Goddard Space Flight Center, provided the TILT/TDRSS support. The TILT unit transmitted the signal to TDRS 6 and was received at the White Sands Second TDRSS Ground Station. This station provided the gateway to the Internet. Coordination also took place at the White Sands station to install a Veridian Firewall and automated security incident measurement (ASIM) system to the Second TDRSS Ground Station Internet gateway. The firewall provides a trusted network for the simulated space experiment. A second Internet connection at the demonstration area was implemented to provide Internet connectivity to a group of workstations to serve as platforms for controlling the simulated space experiment. Installation of this Internet connection was coordinated with an Internet service provider (ISP) and local NASA Johnson Space Center personnel. Not only did this TCP/IP-based architecture prove that a principal investigator on the Internet can securely command and control on-orbit assets, it also demonstrated that valuable virtual testing of planned on-orbit activities can be conducted over the Internet prior to actual deployment in space.

Foltz, David A.↗

Operational implications of a cloud model simulation of space shuttle exhaust clouds in different atmospheric conditions

A three-dimensional cloud model was used to characterize the dominant influence of the environment on the Space Shuttle exhaust cloud. The model was modified to accept the actual heat and moisture from rocket exhausts and deluge water as initial conditions. An upper-air sounding determined the ambient atmosphere in which the cloud would grow. The model was validated by comparing simulated clouds with observed clouds from four actual Shuttle launches. Results are discussed with operational weather forecasters in mind. The model successfully produced clouds with dimensions, rise, decay, liquid water contents, and vertical motion fields very similar to observed clouds whose dimensions were calculated from 16 mm film frames. Once validated, the model was used in a number of different atmospheric conditions ranging from very unstable to very stable. Wind shear strongly affected the appearance of both the ground cloud and vertical column cloud. The ambient low-level atmospheric moisture governed the amount of cloud water in model clouds. Some dry atmospheres produced little or no cloud water. An empirical forecast technique for Shuttle cloud rise is presented and differences between natural atmospheric convection and exhaust clouds are discussed.

Zak, J. A.↗

A cloud model simulation of space shuttle exhaust clouds in different atmospheric conditions

A three-dimensional cloud model was used to characterize the dominant influence of the environment on the Space Shuttle exhaust cloud. The model was modified to accept the actual heat and moisture from rocket exhausts and deluge water as initial conditions. An upper-air sounding determined the ambient atmosphere in which the cloud could grow. The model was validated by comparing simulated clouds with observed clouds from four actual Shuttle launches. The model successfully produced clouds with dimensions, rise, decay, liquid water contents and vertical motion fields very similar to observed clouds whose dimensions were calculated from 16 mm film frames. Once validated, the model was used in a number of different atmospheric conditions ranging from very unstable to very stable. In moist, unstable atmospheres simulated clouds rose to about 3.5 km in the first 4 to 8 minutes then decayed. Liquid water contents ranged from 0.3 to 1.0 g kg-1 mixing ratios and vertical motions were from 2 to 10 ms-1. An inversion served both to reduce entrainment (and erosion) at the top and to prevent continued cloud rise. Even in the most unstable atmospheres, the ground cloud did not rise beyond 4 km and in stable atmospheres with strong low level inversions the cloud could be trapped below 500 m. Wind shear strongly affected the appearance of both the ground cloud and vertical column cloud. The ambient low-level atmospheric moisture governed the amount of cloud water in model clouds. Some dry atmospheres produced little or no cloud water. One case of a simulated TITAN rocket explosion is also discussed.

Chen, C.↗

Ground Testing of an Oxygen Concentrator in a Simulated International Space Station (ISS) Cabin Environment

The method for supplying medical oxygen to respiratorily-compromised astronauts on the International Space Station (ISS) and in future Orion missions consists of drawing oxygen from high pressure oxygen tanks. An Oxygen Concentrator Module (OCM) is a device that pulls in ambient air and separates out the nitrogen, resulting in a high concentration oxygen source. This technology has the potential to eliminate resupply and oxygen-enrichment issues associated with using high pressure oxygen tanks and become an alternative technology to support medical oxygen operations for future exploration missions. In this study, we test the long-term performance of a Commercial Off-the-Shelf (COTS) OCM in a simulated ISS cabin environment. Humidified air, carbon dioxide, and fifteen representative trace contaminants are continuously injected through a enclosed test chamber where the OCM is challenged. This study included the first successful demonstration of the Trace Gas Injection System (TGIS), which reliably and continuously produced ISS levels of trace contaminants, carbon dioxide, and humidity in an enclosed environment. The TGIS is a new and unique ground capability with significant implications for Test Readiness Level (TRL) advancement of COTS items and Government Furnished Equipment (GFE). This study demonstrated that the tested OCM reliably delivers enriched oxygen mostly at desired performance specifications. This study also demonstrated that the OCM does not inadvertently concentrate trace gases in its oxygen product stream, as detectable concentrations of trace contaminants in the oxygen product stream were at all times below the simulated ISS levels.

medical oxygen↗

The Need for Earth-Based Experiments to Inform Microbial Evolution on Planetary Surfaces

Introduction: Historically, the focus of planetary protection at NASA has been on unmanned, robotic missions. Such missions have paved the way for understanding how to implement planetary protection in a feasible and cost-sensitive way. However, with the introduction of crewed missions to Mars in the not-sodistant future, there is a need to better define and understand how to implement planetary protection under new circumstances, as well as understand the risk of contaminating Mars. One unavoidable fact is that microbes will go where humans go. Therefore, it is critical to understand how these microbes may (and will) impact our ability to conduct meaningful, reliable astrobiological science. Microorganisms have spent millions of years evolving to survive in extreme environments here on Earth. Already there are indications that microbes aboard the International Space Station evolve and adapt to life in low earth orbit. The microbes that are eventually taken to Mars with humans will also adapt, potentially causing harmful effects to crew and/or the planetary or astrobiological science conducted. Therefore, it is of critical interest that we evaluate and characterize the potential risks of microbial evolution on Mars. It is expected that microbes carried by humans will begin to evolve to new environments even before landing on Mars, during the several month cruise phase. Once landed, microbes will encounter different stressors within the crew habitats on Mars. During extravehicular activities, venting, or other release events, microbes will find their way out onto the Martian surface. The induced environments around crewed systems will create potentially-favorable conditions for microbes to continue evolving on Mars. Eventually, microbes may find their way beyond the close confines of the crewed area and continue evolving so as to fill new or distant niches on the Martian surface. It is challenging to replicate Martian environments here on Earth, making it nearly impossible to predict the evolutionary changes that microbes would undergo on Mars. But this work is critical. Serial passaging experiments performed by Richard Lenski on E. coli show the dramatic changes microbes can undergo even within a laboratory setting. Furthermore, experiments performed by Michael Baym also demonstrate the power of single mutations in microbial development of antibiotic resistance [3]. Long duration experiments should be performed on a suite of microbes exposed to environments likely to be experienced on the Martian surface. While simulating space environments can be challenging, facilities exist that can achieve individual and combinatorial environmental conditions to simulate space and planetary conditions. Such chambers should be employed for microbial studies. Currently, at the Marshall Space Flight Center, we have used various stressors like drying, vacuum, proton radiation, and ultraviolet light both separately and in combination, to evaluate the survival of cleanroom microbes. Shockingly, several non-spore forming isolates have demonstrated the ability to survive many extreme conditions (manuscript in preparation). These short duration exposures must be augmented with larger and more gradual studies to replicate what microbes might experience in the transition from cruise, to surface habitats, to induced surface environments, and finally true Martian environments. While no Earth-based experiment can perfectly replicate the Martian environment, nor could we test every possible microbe in simulation experimental regimes, efforts should be made to examine the evolutionary potential of the “usual suspects” seen on the ISS or in other crewed environments to begin to fill this important knowledge gap.

Chelsi D. Cassilly↗

Simulation of Space Station loads with active control systems

A methodology for calculating dynamic loads for the Space Station Freedom is presented. The methodology minimizes the repeated calculation of duplicate structural elements, while analyzing a large number of different Space Station configurations with different alpha and beta joint angles. Particular attention is paid to the issue of model reduction using a combination of component mode synthesis (superelements) and component mode selection to generate accurate system level models with a minimum of modal degrees of freedom. The modeling of the control systems during simulation of the structural response is discussed.

Blelloch, P. A.↗

Genomic and Phenotypic Predictors of Human Ex Vivo Sensitivity to Simulated Deep Space Radiation

High-linear energy transfer (LET) ionizing radiation is a major health hazard for astronauts who will be exposed to galactic cosmic rays during upcoming lunar and Mars missions. Predicting and mitigating this risk requires understanding the factors underlying individual radiation sensitivity. We started to address this challenge by identifying the genomic and phenotypic associations with sensitivity to low and high-LET ionizing radiation ex vivo in over 750 healthy human donors. We exposed primary human blood mononuclear cells to simulated galactic cosmic ray components: 350 MeV/n 28Si, 350 MeV/n 40Ar and 600 MeV/n 56Fe particles, at 1.1 and 3 particles/100 sq.m fluences, as well as 0.1 Gy and 1 Gy doses of gamma rays, and analyzed the outcomes at 4 and 24 hours post-irradiation. We quantified DNA damage and repair responses based on 53BP1+ radiation-induced foci formation, together with oxidative stress and changes in secreted factors including immune cytokines and exosomes. We also analyzed phenotypic associations with spontaneous DNA repair foci at baseline prior to irradiation. We identified an increase in spontaneous DNA repair associated with age and latent viral infection, and observed that human spontaneous DNA repair foci at baseline can serve as a negative predictor of DNA repair and immunoregulatory cytokine production after irradiation. Furthermore, we observed a wide variability of subject- and LET-dependent radiation responses, with radiation-induced DNA repair foci increasing by dose and LET, and high-LET particle radiation resulting in more residual DNA damage compared to low-LET particles and gamma rays. We have developed multiple metrics to quantify human radiosensitivity across the spectrum of conditions. Here we present their dependence on radiation quality and phenotypic variables, including an age-dependent decrease in DNA repair after irradiation, and genomic associations with radiosensitivity based on low-coverage whole genome sequencing. We anticipate that our work will pave the way for understanding the spectrum of human radiosensitivity and identifying targets for countermeasure development to reduce DNA and cellular damage and radiation carcinogenesis during deep space exploration.

GWAS↗

Genomic and phenotypic predictors of human ex vivo sensitivity to simulated deep space radiation

High-linear energy transfer (LET) ionizing radiation is a major health hazard for astronauts who will be exposed to galactic cosmic rays during upcoming lunar and Mars missions. Predicting and mitigating this risk requires understanding the factors underlying individual radiation sensitivity. We started to address this challenge by identifying the genomic and phenotypic associations with sensitivity to low and high-LET ionizing radiation ex vivo in over 750 healthy human donors. We exposed primary human blood mononuclear cells to simulated galactic cosmic ray components: 350MeV/n (28)Si, 350MeV/n (40)Ar and 600MeV/n (56)Fe particles, at 1.1 and 3 particles/100µm^(2) fluences, as well as 0.1 Gy and 1 Gy doses of gamma rays, and analyzed the outcomes at 4 and 24 hours post-irradiation. We quantified DNA damage and repair responses based on 53BP1^(+) radiation-induced foci formation, together with oxidative stress and changes in secreted factors including immune cytokines and exosomes. We also analyzed phenotypic associations with spontaneous DNA repair foci at baseline prior to irradiation. We identified an increase in spontaneous DNA repair associated with age and latent viral infection, and observed that human spontaneous DNA repair foci at baseline can serve as a negative predictor of DNA repair and immunoregulatory cytokine production after irradiation. Furthermore, we observed a wide variability of subject- and LET-dependent radiation responses, with radiation-induced DNA repair foci increasing by dose and LET, and high-LET particle radiation resulting in more residual DNA damage compared to low-LET particles and gamma rays. We have developed multiple metrics to quantify human radiosensitivity across the spectrum of conditions. Here we present their dependence on radiation quality and phenotypic variables, including an age-dependent decrease in DNA repair after irradiation, and genomic associations with radiosensitivity based on low-coverage whole genome sequencing. We anticipate that our work will pave the way for understanding the spectrum of human radiosensitivity and identifying targets for countermeasure development to reduce DNA and cellular damage and radiation carcinogenesis during deep space exploration.

GWAS↗

Investigation of critical surface degradation effects on coatings and solar cells developed in Germany (S1002)

Various coatings developed in the FRG (i.e., second-surface mirrors with interference filters with and without conductive layers, conductive layers on solar-cell covers, and selective absorber coatings) have been qualified by accelerated tests under simulated space environment conditions. Experiments with coatings and solar cells have shown, however, that the thermo-optical behavior can differ considerably when performed on the ground and in space because of the great difficulty in simulating the space environment realistically. The objective of this experiment is to qualify these coatings under realistic space environment conditions. In addition, the experiment will provide design criteria, techniques, and test methods to insure control of the combined space and spacecraft environment effects, such as contamination, electrical conductance, and optical degradation, on the coatings. Data to be measured include the temperature of the samples, the electrical resistance of the conductive layers of the samples, the short circuit current of the solar-cell modules, and the deposition of contaminants on the samples (using quartz crystal microbalances (QCM's)).

Preuss, L.↗