Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transitional Flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Aeroelastic Response of the Adaptive Compliant Trailing Edge Transtition Section

The Adaptive Compliant Trailing Edge demonstrator was a joint task under the Environmentally Responsible Aviation Project in partnership with the Air Force Research Laboratory and FlexSys, Inc. (Ann Arbor, Michigan), chartered by the National Aeronautics and Space Administration to develop advanced technologies that enable environmentally friendly aircraft, such as continuous mold-line technologies. The Adaptive Compliant Trailing Edge demonstrator encompassed replacing the Fowler flaps on the SubsoniC Aircraft Testbed, a Gulfstream III (Gulfstream Aerospace, Savannah, Georgia) aircraft, with control surfaces developed by FlexSys, Inc., a pair of uniquely-designed, unconventional flaps to be used as lifting surfaces during flight-testing to substantiate their structural effectiveness. The unconventional flaps consisted of a main flap section and two transition sections, inboard and outboard, which demonstrated the continuous mold-line technology. Unique characteristics of the transition sections provided a challenge to the airworthiness assessment for this part of the structure. A series of build-up tests and analyses were conducted to ensure the data required to support the airworthiness assessment were acquired and applied accurately. The transition sections were analyzed both as individual components and as part of the flight-test article assembly. Instrumentation was installed in the transition sections based on the analysis to best capture the in-flight aeroelastic response. Flight-testing was conducted and flight data were acquired to validate the analyses. This paper documents the details of the aeroelastic assessment and in-flight response of the transition sections of the unconventional Adaptive Compliant Trailing Edge flaps.

ground vibration test↗
NASA NTRS1998

Ascent, Transition, Entry, and Abort Guidance Algorithm Design for the X-33 Vehicle

One of the primary requirements for X-33 is that it be capable of flying autonomously. That is, onboard computers must be capable of commanding the entire flight from launch to landing, including cases where a single engine failure abort occurs. Guidance algorithms meeting these requirements have been tested in simulation and have been coded into prototype flight software. These algorithms must be sufficiently robust to account for vehicle and environmental dispersions, and must issue commands that result in the vehicle operating, within all constraints. Continual tests of these algorithms (and modifications as necessary) will occur over the next year as the X-33 nears its first flight. This paper describes the algorithms in use for X-33 ascent, transition, and entry flight, as well as for the powered phase of PowerPack-out (PPO) aborts (equivalent in thrust impact to losing an engine). All following discussion refers to these phases of flight when discussing guidance. The paper includes some trajectory results and results of dispersion analysis.

Hanson, John M.↗
NASA NTRS2015

Global Precipitation Measurement Mission Launch and Commissioning

During launch and early operation of the Global Precipitation Measurement (GPM) Mission, the Guidance, Navigation, and Control (GN&C) analysis team encountered four main on-orbit anomalies. These include: (1) unexpected shock from Solar Array deployment, (2) momentum buildup from the Magnetic Torquer Bars (MTBs) phasing errors, (3) transition into Safehold due to albedo induced Course Sun Sensor (CSS) anomaly, and (4) a flight software error that could cause a Safehold transition due to a Star Tracker occultation. This paper will discuss ways GN&C engineers identified the anomalies and tracked down the root causes. Flight data and GN&C on-board models will be shown to illustrate how each of these anomalies were investigated and mitigated before causing any harm to the spacecraft. On May 29, 2014, GPM was handed over to the Mission Flight Operations Team after a successful commissioning period. Currently, GPM is operating nominally on orbit, collecting meaningful scientific data that will significantly improve our understanding of the Earth's climate and water cycle.

Guidance Navigation and Control↗
NASA NTRS1989

Results of correlations for transition location on a clean-up glove installed on an F-14 aircraft and design studies for a laminar glove for the X-29 aircraft accounting for spanwise pressure gradient

Results of correlative and design studies for transition location, laminar and turbulent boundary-layer parameters, and wake drag for forward swept and aft swept wings are presented. These studies were performed with the use of an improved integral-type boundary-layer and transition-prediction methods. Theoretical predictions were compared with flight measurements at subsonic and transonic flow conditions for the variable aft swept wing F-14 aircraft for which experimental pressure distributions, transition locations, and turbulent boundary-layer velocity profiles were measured. Flight data were available at three spanwise stations for several values of sweep, freestream unit Reynolds number, Mach numbers, and lift coefficients. Theory/experiment correlations indicate excellent agreement for both transition location and turbulent boundary-layer parameters. The results of parametric studies performed during the design of a laminar glove for the forward swept wing X-29 aircraft are also presented. These studies include the effects of a spanwise pressure gradient on transition location and wake drag for several values of freestream Reynolds numbers at a freestream Mach number of 0.9.

Goradia, S. H.↗
NASA NTRS2005

Knowledge Capture and Management for Space Flight Systems

The incorporation of knowledge capture and knowledge management strategies early in the development phase of an exploration program is necessary for safe and successful missions of human and robotic exploration vehicles over the life of a program. Following the transition from the development to the flight phase, loss of underlying theory and rationale governing design and requirements occur through a number of mechanisms. This degrades the quality of engineering work resulting in increased life cycle costs and risk to mission success and safety of flight. Due to budget constraints, concerned personnel in legacy programs often have to improvise methods for knowledge capture and management using existing, but often sub-optimal, information technology and archival resources. Application of advanced information technology to perform knowledge capture and management would be most effective if program wide requirements are defined at the beginning of a program.

Goodman, John L.↗
NASA NTRS2016

Purpose, Principles, and Challenges of the NASA Engineering and Safety Center

NASA formed the NASA Engineering and Safety Center in 2003 following the Space Shuttle Columbia accident. It is an Agency level, program-independent engineering resource supporting NASA's missions, programs, and projects. It functions to identify, resolve, and communicate engineering issues, risks, and, particularly, alternative technical opinions, to NASA senior management. The goal is to help ensure fully informed, risk-based programmatic and operational decision-making processes. To date, the NASA Engineering and Safety Center (NESC) has conducted or is actively working over 600 technical studies and projects, spread across all NASA Mission Directorates, and for various other U.S. Government and non-governmental agencies and organizations. Since inception, NESC human spaceflight related activities, in particular, have transitioned from Shuttle Return-to-Flight and completion of the International Space Station (ISS) to ISS operations and Orion Multi-purpose Crew Vehicle (MPCV), Space Launch System (SLS), and Commercial Crew Program (CCP) vehicle design, integration, test, and certification. This transition has changed the character of NESC studies. For these development programs, the NESC must operate in a broader, system-level design and certification context as compared to the reactive, time-critical, hardware specific nature of flight operations support.

Gilbert, Michael G.↗
NASA NTRS1973

V/STOL tilt rotor aircraft study: Wind tunnel tests of a full scale hingeless prop/rotor designed for the Boeing Model 222 tilt rotor aircraft

The rotor system designed for the Boeing Model 222 tilt rotor aircraft is a soft-in-plane hingeless rotor design, 26 feet in diameter. This rotor has completed two test programs in the NASA Ames 40' X 80' wind tunnel. The first test was a windmilling rotor test on two dynamic wing test stands. The rotor was tested up to an advance ratio equivalence of 400 knots. The second test used the NASA powered propeller test rig and data were obtained in hover, transition and low speed cruise flight. Test data were obtained in the areas of wing-rotor dynamics, rotor loads, stability and control, feedback controls, and performance to meet the test objectives. These data are presented.

Magee, J. P.↗
NASA NTRS1973

Flight evaluation of two segment approaches for jet transport noise abatement

A 75 flight-hour operational evaluation was conducted with a representative four-engine fan-jet transport in a representative airport environment. The flight instrument systems were modified to automatically provide pilots with smooth and continuous pitch steering command information during two-segment approaches. Considering adverse weather, minimum ceiling and flight crew experience criteria, a transition initiation altitude of approximately 800 feet AFL would have broadest acceptance for initiating two-segment approach procedures in scheduled service. The profile defined by the system gave an upper glidepath of approximately 6 1/2 degrees. This was 1/2 degree greater than inserted into the area navigation system. The glidepath error is apparently due to an erroneous along-track, distance-to-altitude profile.

Rogers, R. A.↗
NASA NTRS1976

RPRV research focus on HiMAT

A review is presented of the F-15 Remotely Piloted Research Vehicle (RPRV) project. The F-15 RPRV is air-launched from a B-52 at 50,000 ft. Following launch a series of research maneuvers are performed during an unpowered descent to a recovery altitude. Another RPRV program considered is the Highly Maneuverable Aircraft Technology (HiMAT) program. This program is designed to use RPRVs to speed the technology transition from wind tunnel to flight and to reduce the cost of aeronautical experiments. It is pointed out that HiMAT will make extensive use of composite materials.

Lockenour, J. L.↗
NASA NTRS1978

VALT parameter identification flight test

The paper describes a method of establishing the accuracy of previously developed analytical models of research vehicles for a program for developing avionics technology for VTOL aircraft. The research vehicle is a Boeing-Vertol CH-47 tandem rotor transport helicopter equipped with a fly-by-wire control system. The specialized flight test was designed to take into account the presence of winds at flight conditions from hover through transition to cruise. The test provided data to obtain estimates of derivatives by parameter identification.

Tomaine, R. L.↗
NASA NTRS1978

Instrumentation for controlling and monitoring environmental control and life support systems

Advanced Instrumentation concepts for improving performance of manned spacecraft Environmental Control and Life Support Systems (EC/LSS) have been developed at Life Systems, Inc. The difference in specific EC/LSS instrumentation requirements and hardware during the transition from exploratory development to flight production stages are discussed. Details of prior control and monitor instrumentation designs are reviewed and an advanced design presented. The latter features a minicomputer-based approach having the flexibility to meet process hardware test programs and the capability to be refined to include the control dynamics and fault diagnostics needed in future flight systems where long duration, reliable operation requires in-flight hardware maintenance. The emphasis is on lower EC/LSS hardware life cycle costs by simplicity in instrumentation and using it to save crew time during flight operation.

Yang, P. Y.↗
NASA NTRS1980

Wind-tunnel tests of the XV-15 tilt rotor aircraft

The XV-15 aircraft was tested in the Ames 40 by 80 Foot Wind Tunnel for preliminary evaluation of aerodynamic and aeroelastic characteristics prior to flight. The tests were undertaken to investigate the aircraft performance, stability, control and structural loads for flight modes from helicopter through transition and airplane mode up to the tunnel capability of 170 knots. Results from these tests are presented.

Weiberg, J. A.↗
NASA NTRS1982

Jet V/STOL wind-tunnel simulation and groundplane effects

The pretest preparation necessary to define the objectives of an appropriate investigation into the jet V/STOL wind tunnel simulation and ground plane effects were examined. Low speed wind tunnel testing of V/STOL aircraft concepts to determine the aerodynamic propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. Powered models are normally used to determine the aerodynamic performance characteristics. Several factors which influence the selection of the model concept and the engine simulator are discussed. Some of the test techniques important for this class of aircraft model are examined. Wind tunnel wall effects important to this aircraft testing with special emphasis on groundplane effects are reviewed.

Margason, R. J.↗
NASA NTRS1981

Jet V/STOL wind-tunnel simulation and groundplane effects

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. Powered models are normally used to determine the aerodynamic performance characteristics. This paper examines some of the pretest preparation necessary to define the objectives of an appropriate investigation. Several factors which influence the selection of the model concept and the engine simulator are discussed. In addition, some of the test techniques important for this class of aircraft model are examined. Finally, the paper reviews some of the wind-tunnel wall effects important to this type of aircraft testing with special emphasis on groundplane effects.

Margason, R. J.↗
NASA NTRS1983

Space flight experience with the Shuttle Orbiter control system

Experience gained through the Shuttle Orbital Flight Test program has matured the engineering understanding of the Shuttle on-orbit control system. The geneology of the control systems (called digital autopilots, or DAPs, and used by the Shuttle for on-orbit operations) is reviewed, the flight experience gained during the flight test program is examined within the context of preflight analysis and test results, and issues for the operational phase of the Shuttle, including constraints upon both operations and analysis still required to increase confidence in the Shuttle's ability to handle capabilities not experienced during the flight test program are addressed. Two orbital autopilots have resulted from computer memory and time constraints on a flight control system, with many different, flight phase unique requirements. The transition DAP, used for insertion and deorbit, has more active sensors and redundancy but a less complex data processing scheme excluding state estimation with fewer choices of operational mode.

Cox, K. J.↗
NASA NTRS1984

The application of a low-order panel method - program VSAERO to powerplant and airframe flow studies

Results from the application of VSAERO, a low-order panel method, to three practical aircraft configurations are presented. The Grumman 698-411 tilt-nacelle V/STOL model is analyzed with particular emphasis on the inlet pressures and the nacelle/fuselage interference effects. Excellent correlation with experiment is reported for the inlet pressure ratio and the inlet operational boundaries. Analysis of an inlet designed for a tilt-rotor/nacelle aircraft is presented. The code was used in a design environment for this configuration to determine an inlet geometry that maintained attached flow for three design flight conditions: hover, hover-transition and cruise. VSAERO is also used to examine the prop-slipstream induced loading for the Langley prop-fan configuration. The versatility and economy of the aerodynamic modeling program, VSAERO, is demonstrated.

Strash, D. J.↗
NASA NTRS1985

A review of some approximate methods used in aerodynamic heating analyses

It is pointed out that preliminary design and optimization studies for new aerospace vehicles require techniques which can calculate aerodynamic heating rates accurately and efficiently. The method employed to calculate the flow field depends to a large extent on the shape of the vehicle, Mach number, Reynolds number, and Knudsen number. In the case of the aero-assisted orbital transfer vehicle (AOTV), a substantial portion of the flight will be in the transitional regime between continuum and free molecule flow. The present paper discusses some approximate methods which have been used to calculate heating rates on high-speed vehicles. Attention is given to the stagnation point and leading edges, the downstream region, the axisymmetric analog, laminar and turbulent heating rates, transition heating rates, gas models, and three-dimensional applications.

Dejarnette, F. R.↗
NASA NTRS1985

Effects of non-uniform velocity profiles on dual jets in a crossflow

The interaction between engine exhaust jets and the freestream affects the aerodynamic and stability characteristics of VTOL aircraft during the transition from hover to forward flight. This interaction is often modeled as a simple uniform jet issuing from a flat plate into a subsonic crossflow. The distribution of pressures induced by the jet on the surface of the plate can be used to predict the lift loss and pitching moment for a full-scale aircraft. The uniform jet model has limitations because an actual turbofan engine generates a rather nonuniform exit velocity profile. The purpose of this work is to study the effect of a nonuniform velocity profile on the surface pressure distribution. The mutual interaction of dual jets also is investigated in side-by-side and tandem configurations. Detailed pressure distributions are presented for two jet-to-freestream velocity ratios of 2.2 and 4.0. One important finding is that a nonuniform jet with a high velocity periphery and a low velocity core has a higher effective velocity ratio than a uniform jet with the same mass flow.

Moore, C. L.↗