Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transonic wind tunnel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗
NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗
NASA NTRS1977

Self streamlining wind tunnel: Low speed testing and transonic test section design

Comprehensive aerodynamic data on an airfoil section were obtained through a wide range of angles of attack, both stalled and unstalled. Data were gathered using a self streamlining wind tunnel and were compared to results obtained on the same section in a conventional wind tunnel. The reduction of wall interference through streamline was demonstrated.

Wolf, S. W. D.↗
NASA NTRS1979

Development of the cryogenic tunnel concept and application to the US National Transonic Facility

A fan-driven, high Reynolds number, transonic cryogenic wind tunnel is described. The tunnel has a 2.5- by 2.5 m test section and is capable of operating from ambient to cryogenic temperatures at stagnation pressures up to 8.8 atm. An overview of the cryogenic concept and discussions of drive power requirements, support systems, and operating characteristics and performance of the wind tunnel are included.

Kilgore, R. A.↗
NASA NTRS1977

Experiment and analysis on the flow process dynamics of the NASA-Langley eight foot transonic pressure tunnel

A dynamic response test performed in a eight foot transonic pressure tunnel is described. The dynamics of the flow process of the wind tunnel at transonic conditions were obtained. Descriptions of the test conditions, instrumentation, presentation of raw data, analysis of data, and finally, based on experimental evidences, an attempt to construct an input output relationship of the flow process from the viewpoints of control engineering are included.

Tcheng, P.↗
NASA NTRS1985

The adaptive wall test section for the NASA Langley 0.3-m Transonic Cryogenic Tunnel

The effect of wind tunnel wall interference on transonic aerodynamic data obtained in a ventilated test section is difficult to predict. The magnitude of the interference can be reduced and the prediction of the level of interference can be simplified by testing in a test section with solid, adaptive walls. An adaptive wall test section configured for two dimensional testing has been installed in the circuit of the Langley 0.3-m Transonic Cryogenic Tunnel. The unique features of the tunnel and the new test section are described. An overview of computer software to configure the walls along streamsurfaces is presented along with a description of the of the experiments planned to assess the capabilities of the new test section.

Mineck, Raymond E.↗
NASA NTRS1955

Comparison of the Drag of a Fin-Stabilized Body of Revolution and of a Complete Airplane Configuration as Obtained at Transonic Speeds in a Slotted Wind Tunnel and in Free Flight

A comparison of the zero-lift drag coefficients at Mach numbers from 0.81 to 1.41 of a fin-stabilized parabolic body of revolution as measured in the Langley transonic blowdown tunnel has been made with measurements obtained in free-flight on a larger but geometrically similar model. The absolute values of drag coefficient obtained in the slotted wind tunnel were equivalent to the free-flight drag-coefficient values up to a Mach number of 1.4 when adjustments were made for the effect on viscous drag of differences in Reynolds number between the two test conditions. Excellent agreement was obtained between the two tests for the pressure-drag variation with Mach number, regardless of whether the scale effect on skin friction was considered. Favorable agreement was also obtained between the pressure-drag increments due t o the presence of the stabilizing fins as determined in the wine tunnel from fins-on and fins-off tests and as obtained by a different method in free flight. Tests of a specific airplane configuration to obtain an indication of the problems involved in the construction and tests of small-scale (approximately 7-inch span) complete airplane configuration with internal air flow indicated that reliable zero-lift drag-coefficient measurements at Mach numbers up to 1.4 can be attained with such models, provided the model is constructed with a high but not an unreasonable degree of accuracy.

Howell, Robert R.↗
NASA NTRS1991

Recent rotorcraft aeroelastic testing in the Langley Transonic Dynamics Tunnel

Wind-tunnel testing of a properly scaled aeroelastic model helicopter rotor is considered a necessary phase in the design and development of new rotor systems. For this reason, extensive testing of aeroelastically scaled model rotors is done in the Transonic Dynamics Tunnel (TDT) located at the Langley Research Center. A unique capability of this facility, which enables proper dynamic scaling, is the use of diflourodichloromethane, or Refrigerant-12 (R-12) as a test medium. The paper presents a description of the TDT and a discussion of the benefits of using R-12 as a test medium. A description of the system used to conduct model tests is provided and examples of recent rotor tests are cited to illustrate the types of aeroelastic model rotor tests conducted in the TDT.

Yeager, William T., Jr.↗
NASA NTRS2018

Experimental Evaluation of BLI Propulsion: The Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan Solution

NASA has successfully developed a new testbed configuration for experimentally evaluating embedded boundary layer ingesting aircraft propulsors in its 8'x6' Supersonic Wind Tunnel. This testbed meets the challenges of providing the necessary freestream flow Mach conditions and desired range and distribution of boundary layer thickness for embedded aircraft propulsion systems. The testbed consists of a 48ft long raised wind tunnel floor aircraft surface simulator and a boundary layer regulation system to produce propulsion-local aircraft aerodynamic flow fields. This durable special test equipment is designed to be installed in the wind tunnel's transonic test section and is capable of evaluating a wide range of subcritical and supercritical airframe-propulsion integration configurations for subsonic cruise aircraft. The wind tunnel and testbed are well suited for meeting the test requirements of these propulsors in the most cost efficient way and has been aerodynamically calibrated and proven through tests of a first-of-its-kind boundary layer ingesting propulsor.

Arend, David J.↗
NASA NTRSDate not supplied

Comparisons of Artemis I and Wind Tunnel Buffet Environments and Induced Structural Responses

This paper presents comparisons of buffet forcing functions (BFFs) and associated structural responses for the Space Launch System from two data sources: 1) Artemis I (AR01) Developmental Flight Instrumentation (DFI) and 2) transonic wind-tunnel (WT) tests. Failures of DFI sensors prevented the development of a complete set of flight-based BFFs, where each BFF is based on azimuthal integration over 360-degrees of unsteady pressures acquired by sensor rings placed at many longitudinal stations along the vehicle. Instead, a set of equivalent flight- and WT-based BFFs was developed based on functional DFI and WT sensors that share the same locations. Root-mean-square (rms) levels of equivalent BFFs from flight and WT data are in-family for most of the cardinal Mach numbers. However, at stations downstream of the booster forward attachment (FA) protuberance, the rms of flight-based BFFs exceed their WT counterparts. Strikingly, vortex-shedding off the FA protuberance occurs at lower frequencies during flight than in WT experiments. This frequency shift propagates onto the spectrum of flight-measured vs. WT-based structural responses. Aside from vortex-shedding frequency mismatch, a generally good agreement between AR01 and WT-based responses is an indirect indication that WT buffet environments are fairly well representative of their AR01 counterpart.

transonic buffet↗
NASA NTRSDate not supplied

Comparisons of Artemis I and Wind Tunnel Buffet Environments and Induced Structural Responses

This paper presents comparisons of buffet forcing functions (BFFs) and associated structural responses for the Space Launch System from two data sources: 1) Artemis I (AR01) Developmental Flight Instrumentation (DFI) and 2) transonic wind-tunnel (WT) tests. Failures of DFI sensors prevented the development of a complete set of flight-based BFFs, where each BFF is based on azimuthal integration over 360-degrees of unsteady pressures acquired by sensor rings placed at many longitudinal stations along the vehicle. Instead, a set of equivalent flight- and WT-based BFFs was developed based on functional DFI and WT sensors that share the same locations. Root-mean-square (rms) levels of equivalent BFFs from flight and WT data are in-family for most of the cardinal Mach numbers. However, at stations downstream of the booster forward attachment (FA) protuberance, the rms of flight-based BFFs exceed their WT counterparts. Strikingly, vortex-shedding off the FA protuberance occurs at lower frequencies during flight than in WT experiments. This frequency shift propagates onto the spectrum of flight-measured vs. WT-based structural responses. Aside from vortex-shedding frequency mismatch, a generally good agreement between AR01 and WT-based responses is an indirect indication that WT buffet environments are fairly well representative of their AR01 counterpart.

transonic buffet↗
NASA NTRS2015

Application of FLEET Velocimetry in the NASA Langley 0.3-meter Transonic Cryogenic Tunnel

Femtosecond laser electronic excitation and tagging (FLEET) velocimetry is demonstrated in a large-scale transonic cryogenic wind tunnel. Test conditions include total pressures, total temperatures, and Mach numbers ranging from 15 to 58 psia, 200 to 295 K, and 0.2 to 0.75, respectively. Freestream velocity measurements exhibit accuracies within 1 percent and precisions better than 1 m/s. The measured velocities adhere closely to isentropic flow theory over the domain of temperatures and pressures that were tested. Additional velocity measurements are made within the tunnel boundary layer; virtual trajectories traced out by the FLEET signal are indicative of the characteristic turbulent behavior in this region of the flow, where the unsteadiness increases demonstrably as the wall is approached. Mean velocities taken within the boundary layer are in agreement with theoretical velocity profiles, though the fluctuating velocities exhibit a greater deviation from theoretical predictions.

Burns, Ross A.↗
NASA NTRS2017

Computational Design and Analysis of a Transonic Natural Laminar Flow Wing for a Wind Tunnel Model

A natural laminar flow (NLF) wind tunnel model has been designed and analyzed for a wind tunnel test in the National Transonic Facility (NTF) at the NASA Langley Research Center. The NLF design method is built into the CDISC design module and uses a Navier-Stokes flow solver, a boundary layer profile solver, and stability analysis and transition prediction software. The NLF design method alters the pressure distribution to support laminar flow on the upper surface of wings with high sweep and flight Reynolds numbers. The method addresses transition due to attachment line contamination/transition, Gortler vortices, and crossflow and Tollmien-Schlichting modal instabilities. The design method is applied to the wing of the Common Research Model (CRM) at transonic flight conditions. Computational analysis predicts significant extents of laminar flow on the wing upper surface, which results in drag savings. A 5.2 percent scale semispan model of the CRM NLF wing will be built and tested in the NTF. This test will aim to validate the NLF design method, as well as characterize the laminar flow testing capabilities in the wind tunnel facility.

Lynde, Michelle N.↗
NASA NTRS2002

Flow Visualization of Density in a Cryogenic Wind Tunnel Using Planar Rayleigh and Raman Scattering

Using a pulsed Nd:YAG laser (532 nm) and a gated, intensified charge-coupled device, planar Rayleigh and Raman scattering techniques have been used to visualize the unseeded Mach 0.2 flow density in a 0.3-meter transonic cryogenic wind tunnel. Detection limits are determined for density measurements by using both unseeded Rayleigh and Raman (N2 vibrational) methods. Seeding with CO2 improved the Rayleigh flow visualization at temperatures below 150 K. The seeded Rayleigh version was used to demonstrate the observation of transient flow features in a separated boundary layer region, which was excited with an oscillatory jet. Finally, a significant degradation of the laser light sheet, in this cryogenic facility, is discussed.

Herring, Gregory C.↗
NASA NTRS1982

Aerodynamic characteristics of airfoils with ice accretions

Results of a wind tunnel test to evaluate the performance of an airfoil with simulated rime ice are presented with theoretical comparisons. A NACA 65A413 airfoil was tested in the OSU 6 x 22 inch Transonic Airfoil Wind Tunnel at a Reynolds number near three million and Mach numbers from 0.20 to 0.80. The model was tested in four configurations to determine the aero-dynamic effects of the roughness and shape of a rime ice accretion. The simulated rime ice shape was obtained analytically using a time-stepping dry ice accretion computer code. Lift, drag, moment coefficients, and pressure distributions for the clean and simulated rime ice cases are reported. The measured degradation in airfoil performance is compared to an analytical method which uses existing airfoil analysis computer codes with empirical corrections for the surface roughness. A discussion of the empirical surface roughness correction and uses of other airfoil computer methods is included.

Bragg, M. B.↗
NASA NTRS1991

Wall-interference assessment and corrections for transonic NACA 0012 airfoil data from various wind tunnels

A nonlinear, four wall, post-test wall interference assessment/correction (WIAC) code was developed for transonic airfoil data from solid wall wind tunnels with flexibly adaptable top and bottom walls. The WIAC code was applied over a broad range of test conditions to four sets of NACA 0012 airfoil data, from two different adaptive wall wind tunnels. The data include many test points for fully adapted walls, as well as numerous partially adapted and unadapted test points, which together represent many different model/tunnel configurations and possible wall interference effects. Small corrections to the measured Mach numbers and angles of attack were obtained from the WIAC code even for fully adapted data; these corrections generally improve the correlation among the various sets of airfoil data and simultaneously improve the correlation of the data with calculations for a 2-D, free air, Navier-Stokes code. The WIAC corrections for airfoil data taken in fully adapted wall test sections are shown to be significantly smaller than those for comparable airfoil data from straight, slotted wall test sections. This indicates, as expected, a lesser degree of wall interference in the adapted wall tunnels relative to the slotted wall tunnels. Application of the WIAC code to this data was, however, somewhat more difficult and time consuming than initially expected from similar previous experience with WIAC applications to slotted wall data.

Green, Lawrence L.↗
NASA NTRS2003

Introduction to the Abrupt Wing Stall (AWS) Program

The Abrupt Wing Stall (AWS) Program has addressed the problem of uncommanded, transonic lateral motions, such as wing drop, with experimental, computational, and simulation tools. Background to the establishment of the AWS program is given as well as program objectives. In order to understand the fundamental flow mechanisms that caused the undesirable motions for a pre-production version of the F/A-18E, steady and unsteady flow field details were gathered from dedicated transonic wind-tunnel testing and computational studies. The AWS program has also adapted a free-to-roll (FTR) wind-tunnel testing technique traditionally used for low-speed studies of lateral dynamic stability to the transonic flow regime. This FTR capability was demonstrated first in a proof-of -concept study and then applied to an assessment of four different aircraft configurations. Figures of merit for static testing and for FTR testing have been evaluated for two configurations that demonstrated wing drop susceptibility during full-scale flight conditions (the pre-production F/A-18E and the AV-8B at the extremes of its flight envelope) and two configurations that do not exhibit wing drop (the F/A-18C and the F-16C). Design insights have been obtained from aerodynamic computational studies of the four aircraft configurations and from computations quantifying the impact of the various geometric wing differences between the F/A-18C and the F/A-18E wings. Finally, the AWS program provides guidance for assessing, in the simulator, the impact of experimentally determined lateral activity on flight characteristics before going to flight.

Hall, Robert M.↗