Search NASA⌕ Search

SEARCH · Search NASA

Results for “Turbulence experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Acoustic properties of supersonic helium/air jets at low Reynolds numbers

Experiments have been performed with the objective of developing a greater understanding of the physics of hot supersonic jet noise. Cold helium/air jets are used to easily and inexpensively simulate the low densities of hot air jets. The experiments are conducted at low Reynolds numbers in order to facilitate study of the large-scale turbulent structures (instability waves) that cause most of the radiated noise. Experiments have been performed on Mach 1.5 and 2.1 jets of pure air, pure helium and 10 percent helium by mass. Helium/air jets are shown to radiate more noise than pure air jets due to the increased exit velocity. Microphone spectra are usually dominated by a single spectral component at a predictable frequency. Increasing the jet's helium concentration is shown to increase the dominant frequency. The helium concentration in the test chamber is determined by calculating the speed of sound from the measured phase difference between two microphone signals. Bleeding outside air into the test chamber controls the accumulation of helium so that the hot jet simulation remains valid. The measured variation in the peak radiated noise frequency is in good agreement with the predictions of the hot jet noise theory of Tam et al.

Mclaughlin, Dennis K.↗
NASA NTRS1993

Particle-Gas Dynamics in the Midplane of a Protoplanetary Nebula

In this paper, we study the stage of planetary formation during which the particulate material is still dispersed as centimeter-to-meter sized primordial aggregates. During this stage, particles are able to settle toward the midplane into a layer of mass density comparable to or much greater than that of the gas. Nonlinear, coupled interactions between the particles and the nebula gas become significant and ultimately determine the vertical profiles of the particle density and the mean velocities of the particles and the nearby gas. This is the environment in which the earliest planetesimals probably form. Our numerical models rely on the Reynolds averaged Navier-Stokes equations for the gas and particles and are fully viscous and turbulent (and, for the particles. compressible). Our turbulence modeling uses a Prandtl local shear parametrization, validated by laboratory experiments. We have developed a new model for particle diffusion involving the profile of the nebula gas turbulence and the particle Schmidt number, which is a function of particle size and density. We model a cool, quiescent nebula at 1 AU (280 K) and 10 AU (90 K) and a higher temperature stage (1000 K) at 1 AU. Our main results include: (a) rapid accretion of planetesimals by gravitationally unstable fragmentation on an orbital time scale (the 'Goldreich-Ward instability') is unlikely to occur until objects have already accreted by some other process to the mass of the largest known meteorite samples, if at all; (b) from 'seeds' as small as 10 m, growth of 10- to 100-km planetesimals can proceed rapidly by drift-augmented accretion in the particle-rich midplane with orbital decay of about 1% for the growing planetesimals; (c) outward transport of vapor and small entrained chips can account for significant radial compositional and mineralogical mixing in primitive meteorite parent bodies. Other implications may be drawn concerning particle random collisional velocities and the time scales of midplane turbulence.

Cuzzi, Jeffrey N.↗
NASA NTRS2016

Goals and Status of the NASA Juncture Flow Experiment

The NASA Juncture Flow experiment is a new effort whose focus is attaining validation data in the juncture region of a wing-body configuration. The experiment is designed specifically for the purpose of CFD validation. Current turbulence models routinely employed by Reynolds-averaged Navier-Stokes CFD are inconsistent in their prediction of corner flow separation in aircraft juncture regions, so experimental data in the near-wall region of such a configuration will be useful both for assessment as well as for turbulence model improvement. This paper summarizes the Juncture Flow effort to date, including preliminary risk-reduction experiments already conducted and planned future experiments. The requirements and challenges associated with conducting a quality validation test are discussed.

Rumsey, Christopher L.↗
NASA NTRS2011

Assessment of CFD Hypersonic Turbulent Heating Rates for Space Shuttle Orbiter

Turbulent CFD codes are assessed for the prediction of convective heat transfer rates at turbulent, hypersonic conditions. Algebraic turbulence models are used within the DPLR and LAURA CFD codes. The benchmark heat transfer rates are derived from thermocouple measurements of the Space Shuttle orbiter Discovery windward tiles during the STS-119 and STS-128 entries. The thermocouples were located underneath the reaction-cured glass coating on the thermal protection tiles. Boundary layer transition flight experiments conducted during both of those entries promoted turbulent flow at unusually high Mach numbers, with the present analysis considering Mach 10{15. Similar prior comparisons of CFD predictions directly to the flight temperature measurements were unsatisfactory, showing diverging trends between prediction and measurement for Mach numbers greater than 11. In the prior work, surface temperatures and convective heat transfer rates had been assumed to be in radiative equilibrium. The present work employs a one-dimensional time-accurate conduction analysis to relate measured temperatures to surface heat transfer rates, removing heat soak lag from the flight data, in order to better assess the predictive accuracy of the numerical models. The turbulent CFD shows good agreement for turbulent fuselage flow up to Mach 13. But on the wing in the wake of the boundary layer trip, the inclusion of tile conduction effects does not explain the prior observed discrepancy in trends between simulation and experiment; the flight heat transfer measurements are roughly constant over Mach 11-15, versus an increasing trend with Mach number from the CFD.

Wood, William A.↗
NASA NTRS1977

An experimental and computational investigation of the steady and unsteady transonic flow fields about an airfoil in a solid-wall test channel

An experimental and computational investigation of the steady and unsteady transonic flow field about a thick airfoil is described. An operational computer code for solving the two-dimensional, compressible Navier-Stokes equations for flow over airfoils was modified to include solid-wall, slipflow boundary conditions to properly assess the code and help guide the development of improved turbulence models. Steady and unsteady flow fields about an 18% thick circular arc airfoil at Mach numbers of 0.720, 0.754, and 0.783 and a chord Reynolds number of 11 x 10 to the 6th are predicted and compared with experiment. For the first time, computed results for unsteady turbulent flows with separation caused by a shock wave were obtained which qualitatively reproduce the time-dependent aspects of experiments. Features such as the intensity and reduced frequency of airfoil surface-pressure fluctuations, oscillatory regions of trailing-edge and shock-induced separation, and the Mach number range for unsteady flows were all qualitatively reproduced.

Levy, L. L., Jr.↗
NASA NTRS1998

Experimental Study of Boundary Layer Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. Freestream turbulence levels ranging from 0.8% to 3% was used in this experiment. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. Hot-wires (single and x-wire) and surface mounted hot-film gases and static pressure taps were used to map the flowfield. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Shyne, Rickey J.↗
NASA NTRS1990

Turbulent statistics in the vicinity of an SST front: A north wind case, FASINEX February 16, 1986

The technique of boxcar variances and covariances is used to examine NCAR Electra data from FASINEX (Frontal Air-Sea Interaction EXperiment). This technique was developed to examine changes in turbulent fluxes near a sea surface temperature (SST) front. The results demonstrate the influence of the SST front on the MABL (Marine Atmospheric Boundary Layer). Data shown are for February 16, 1986, when the winds blew from over cold water to warm. The front directly produced horizontal variability in the turbulence. The front also induced a secondary circulation which further modified the turbulence.

Stage, Steven A.↗
NASA NTRS2001

Evaluation of Turbulence-Model Performance in Jet Flows

The importance of reducing jet noise in both commercial and military aircraft applications has made jet acoustics a significant area of research. A technique for jet noise prediction commonly employed in practice is the MGB approach, based on the Lighthill acoustic analogy. This technique requires as aerodynamic input mean flow quantities and turbulence quantities like the kinetic energy and the dissipation. The purpose of the present paper is to assess existing capabilities for predicting these aerodynamic inputs. Two modern Navier-Stokes flow solvers, coupled with several modern turbulence models, are evaluated by comparison with experiment for their ability to predict mean flow properties in a supersonic jet plume. Potential weaknesses are identified for further investigation. Another comparison with similar intent is discussed by Barber et al. The ultimate goal of this research is to develop a reliable flow solver applicable to the low-noise, propulsion-efficient, nozzle exhaust systems being developed in NASA focused programs. These programs address a broad range of complex nozzle geometries operating in high temperature, compressible, flows. Seiner et al. previously discussed the jet configuration examined here. This convergent-divergent nozzle with an exit diameter of 3.6 inches was designed for an exhaust Mach number of 2.0 and a total temperature of 1680 F. The acoustic and aerodynamic data reported by Seiner et al. covered a range of jet total temperatures from 104 F to 2200 F at the fully-expanded nozzle pressure ratio. The aerodynamic data included centerline mean velocity and total temperature profiles. Computations were performed independently with two computational fluid dynamics (CFD) codes, ISAAC and PAB3D. Turbulence models employed include the k-epsilon model, the Gatski-Speziale algebraic-stress model and the Girimaji model, with and without the Sarkar compressibility correction. Centerline values of mean velocity and mean temperature are compared with experimental data.

Woodruff, S. L.↗
DOE OSTI2020

Study of turbulence-induced refraction of lower hybrid waves using synthetic scrape-off layer filaments

Here, turbulence-induced refraction effects to lower hybrid (LH) wave propagation and current drive are studied using synthetic scrape-off layer (SOL) blob/filament fields. A synthetic 3D, field-following, blob turbulence model is implemented in the ray-tracing/Fokker-Planck (RTFP) codes GENRAY/CQL3D. In Alcator C-Mod, the blob field is shown to significantly affect LH ray-trajectories, leading to increased on-axis damping and smoother current profiles. This effect depends on the average blob size and amplitude. In addition, the diffusion of ray-trajectories in phase-space caused by turbulence increases the robustness of the RTFP model. A modified $N_{||}$ launch spectrum, acting as a proxy for parametric decay instability (PDI) effects, is included in simulations with the blob model. A synergy between the modified launch spectrum and turbulence-induced refraction results in synthetic hard x-ray profiles that agree with experiment. Lastly, the blob model is used to predict the effect of SOL turbulence on DIII-D high-field side (HFS) LH launch. Assuming low turbulence amplitude in the HFS SOL (~5%), turbulence-induced refraction is predicted to have little effect on current drive efficiency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1981

A laboratory experiment on EM backscatter from Farley-Buneman and gradient drift waves

Results of laboratory experiment on Bragg backscatter of 3-cm microwaves by turbulent waves driven by the Farley-Buneman and gradient drift instabilities are reported. It is noted that the study is the third in a series of laboratory experiments performed to test, under controlled conditions, prevalent ideas on EM scattering by equatorial and high-latitude ionospheric waves and irregularities. It is shown through separate backscattering from fast and slow ion beam modes that a beam of EM radiation actually provides, in backscatter, information on the spectral content of the scattering medium.

Alport, M. J.↗
NASA NTRS2001

An Investigation of Fully Modulated, Turbulent Diffusion Flames in Reduced Gravity

Pulsed combustion appears to have the potential to provide for rapid fuel/air mixing, compact and economical combustors, and reduced exhaust emissions. The objective of this Flight-Definition experiment (PuFF, for Pulsed-Fully Flames) is to increase the fundamental understanding of the fuel/air mixing and combustion behavior of pulsed, turbulent diffusion flames by conducting experiments in microgravity. In this research the fuel jet is fully modulated (i.e., completely shut off between pulses) by an externally controlled valve system. This gives rise to drastic modification of the combustion and flow characteristics of flames, leading to enhanced fuel/air mixing mechanisms not operative for the case of acoustically excited or partially-modulated jets. The fully-modulated injection approach also simplifies the combustion process by avoiding the acoustic forcing generally present in pulsed combustors. Relatively little is known about the behavior of turbulent flames in reduced-gravity conditions, even in the absence of pulsing. Fundamental issues addressed in this experiment include the impact of buoyancy on the fuel/air mixing and combustion characteristics of fully-modulated flames. It is also important for the planned space experiments to establish the effects of confinement and oxidizer co-flow on these flames.

Hermanson, J. C.↗
NASA NTRS1989

Turbulent small-scale neutral and ion density fluctuations as measured during MAC/Epsilon

During the MAC/Epsilon campaign (Fall 1987, from Andoya, Northern Norway, 69 N, 16 E) a total of four altitude profiles of neutral gas number densities and six profiles of ion number densities were measured with high spatial resolution in the height range from 60 to 120 km. First results of these rocket-borne experiments are presented with emphasis on small scale turbulent density variations and related turbulent parameter as structure function constants and energy dissipation rates.

Luebken, F.-J.↗
DOE OSTI2020

Rayleigh-Taylor Instability: A Status Review of Experimental Designs and Measurement Diagnostics

The focus of experiments and the sophistication of diagnostics employed in Rayleigh-Taylor instability (RTI) induced mixing studies have evolved considerably over the past seven decades. The first theoretical analysis by Taylor and the two-dimensional experimental results by Lewis on RTI in 1950 examined single-mode RTI using conventional imaging techniques. Over the next 70 years, several experimental designs have been used to creating an RTI unstable interface between two materials of different densities. These early experiments though innovative, were arduous to diagnose and provided little information on the internal, turbulent structure and initial conditions of the RT mixing layer. Coupled with the availability of high-fidelity diagnostics, the experiments designed and developed in the last three decades allow detailed measurements of various turbulence statistics that have allowed broadly to validate and verify late-time nonlinear models and mix-models for buoyancy-driven flows. Besides, they have provided valuable insights to solve several long-standing disagreements in the field. Herein, this review serves as an opportunity to discuss the understanding of the RTI problem and highlight valuable insights gained into the RTI driven mixing process with a focus on low to high Atwood number (> 0.1) experiments.

42 ENGINEERING↗
NASA NTRS2003

Characterizing the Severe Turbulence Environments Associated with Commercial Aviation Accidents: Hydrostatic Mesobeta Scale Numerical Simulations of Supergradient Wind Flow and Streamwise Ageostrophic Frontogenesis - Part 2

Simulation experiments reveal key processes that organize a hydrostatic environment conducive to severe turbulence. The paradigm requires juxtaposition of the entrance region of a curved jet stream, which is highly subgeostrophic, with the entrance region of a straight jet stream, which is highly supergeostrophic. The wind and mass fields become misphased as the entrance regions converge resulting in the significant spatial variation of inertial forcing, centripetal forcing, and along- and cross-stream pressure gradient forcing over a mesobeta scale region. This results in frontogenesis and the along-stream divergence of cyclonic and convergence of cyclonic ageostrophic vertical vorticity. The centripetally forced mesoscale front becomes the locus of large gradients of ageostrophic vertical vorticity along an overturning isentrope. This region becomes favorable for streamwise vorticity gradient formation enhancing the environment for organization of horizontal vortex tubes in the presence of buoyant forcing.

Kaplan, Michael L.↗
NASA NTRS2008

A New Technique using Electron Velocity Data from the Four Cluster Spacecraft to Explore Magnetofluid Turbulence in the Solar Wind

It is now possible in certain circumstances to use velocity moments computed from the Plasma Electron and Current Experiment (PEACE) on the four Cluster spacecraft to determine a number of turbulence properties of the solar wind, including direct measurements of the vorticity and compressibility. Assuming that the four spacecraft are not co-planar and that there is only a linear variation of the plasma variables across the volume defined by the four satellites, one can estimate the curl of the fluid velocity, i.e., the vorticity. From the vorticity it is possible to explore directly intermittent regions in the solar wind where dissipation is likely to be enhanced. In addition, one can estimate directly the Taylor microscale.

Goldstein, Melvyn L.↗
NASA NTRS2016

Direct Numerical Simulation of an Airfoil with Sand Grain Roughness on the Leading Edge

As part of a computational study of acoustic radiation due to the passage of turbulent boundary layer eddies over the trailing edge of an airfoil, the Lattice-Boltzmann method is used to perform direct numerical simulations of compressible, low Mach number flow past an NACA 0012 airfoil at zero degrees angle of attack. The chord Reynolds number of approximately 0.657 million models one of the test conditions from a previous experiment by Brooks, Pope, and Marcolini at NASA Langley Research Center. A unique feature of these simulations involves direct modeling of the sand grain roughness on the leading edge, which was used in the abovementioned experiment to trip the boundary layer to fully turbulent flow. This report documents the findings of preliminary, proof-of-concept simulations based on a narrow spanwise domain and a limited time interval. The inclusion of fully-resolved leading edge roughness in this simulation leads to significantly earlier transition than that in the absence of any roughness. The simulation data is used in conjunction with both the Ffowcs Williams-Hawkings acoustic analogy and a semi-analytical model by Roger and Moreau to predict the farfield noise. The encouraging agreement between the computed noise spectrum and that measured in the experiment indicates the potential payoff from a full-fledged numerical investigation based on the current approach. Analysis of the computed data is used to identify the required improvements to the preliminary simulations described herein.

Ribeiro, Andre F. P.↗