Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode utilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Solvent-Free and Non-Sintered 500 Wh/kg All Solid-State Battery

Navitas teamed up with UMD and ORNL to establish a reliable scientific research team. The project addressed processing limitations of state-of-the-art solid electrolytes by extending solvent-free electrode fabrication technology to the scalable production of cathode/solid electrolyte laminates. The innovation started with a solid-state sulfide electrolyte (LiPS) with Cl stabilization able to meet the keystone conductivity challenge in a film of practical thickness (μ 50 µm). The electrolyte was based on a composite of PTFE, and stabilized LiPSCl. With optimization, the ionic conductivity reached 3.3 ×10 -3 S/cm. The solid electrolyte with as low as 0.4% binder allowed long term cycling (> 500 cycles) of Li/SSE/Li cell at > 4 mA/cm 2 with the utilization of Li > 80%. The Li and SSE interfaces were successfully protected with LiF-rich SEI layer. NCM811cathode active materials were coated with a thin layer of Al 2 O 3 (5 nm). The free standing cathode film was fabricated through dry-process with Al2O3-coated NCM811, LiPSCl, active carbon, and small amount PTFE. The all-solid-state batteries were laminated with free standing surface coated NCM811 cathode film, free standing LiPSCl SSE film, and surface protected Li anode together in a single lamination step, and demonstrated high specific capacity (> 200 mAh/g) with coulombic efficiency > 99.5%. The all-solid-state batteries through solvent-free and no-sintering process are promising for large format cell with 500 Wh/Kg specific energy density.

25 ENERGY STORAGE↗

The Importance of Nanometric Passivating Films on Cathodes forLi - Air Batteries

Recently, there has been a transition from fully carbonaceous positive electrodes for the aprotic lithium oxygen battery to alternative materials and the use of redox mediator additives, in an attempt to lower the large electrochemical overpotentials associated with the charge reaction. However, the stabilizing or catalytic effect of these materials can become complicated due to the presence of major side-reactions observed during dis(charge). Here, we isolate the charge reaction from the discharge by utilizing electrodes prefilled with commercial lithium peroxide with a crystallite size of about 200-800 nm. Using a combination of S/TEM, online mass spectrometry, XPS, and electrochemical methods to probe the nature of surface films on carbon and conductive Ti-based nanoparticles, we show that oxygen evolution from lithium peroxide is strongly dependent on their surface properties. Insulating TiO2 surface layers on TiC and TiN - even as thin as 3 nm*can completely inhibit the charge reaction under these conditions. On the other hand, TiC, which lacks this oxide film, readily facilitates oxidation of the bulk Li2O2 crystallites, at a much lower overpotential relative to carbon. Since oxidation of lithium oxygen battery cathodes is inevitable in these systems, precise control of the surface chemistry at the nanoscale becomes of upmost importance.

Adams, Brian D.↗

A Nickel-Decorated Carbon Flower/Sulfur Cathode for Lean-Electrolyte Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries involve a reversible conversion reaction between sulfur and lithium sulfide (Li 2 S) via a series of soluble lithium polysulfide intermediates (LiPSs), enabling a high theoretical specific capacity of 1675 mAh g –1 . However, this process exhibits large polarization and low sulfur utilization and suffers critical capacity fade. The primary approach to tackle the problem has so far been to infiltrate sulfur into nanostructured carbon. Furthermore, most studies using porous carbon as host materials have tested with high electrolyte to sulfur ratios (E/S) (generally > 15 µL mg –1 ) that compromise the cell-level energy density. Here, a flower-shaped porous carbon structure with nickel nanoparticles that can address the problems discussed above is designed. First, the 3D flower-shaped carbon structure enables short ionic transport lengths. Second, the small pore diameters <10 nm and high specific surface areas > 3300 m 2 g –1 with sufficient pore volume are ideal for charging performance for low E/S ratios. Finally, Ni nanoparticles are employed onto the flower-shaped network to improve the reaction kinetics. Collectively, it is successfully demonstrated that the batteries with a high mass loading of 5 mg cm –2 and a 5 µL mg –1 E/S ratio can retain cycle retention of 70% after 150 cycles.

25 ENERGY STORAGE↗

Revisit Carbon/Sulfur Composite for Li-S Batteries

To correlate the carbon properties e.g. surface area and porous structure, with the electrochemical behaviors of carbon/sulfur (C/S) composite cathodes for lithium-sulfur (Li-S) batteries, four different carbon frameworks including Ketjen Black (KB, high surface area and porous), Graphene (high surface area and nonporous), Acetylene Black (AB, low surface area and nonporous) and Hollow Carbon Nano Sphere (HCNS, low surface area and porous) are employed to immobilize sulfur (80 wt.%). It has been revealed that high surface area of carbon improves the utilization rate of active sulfur and decreases the real current density during the electrochemical reactions. Accordingly, increased reversible capacities and reduced polarization are observed for high surface area carbon hosts such as KB/S and graphene/S composites. The porous structure of KB or HCNS matrix promotes the long-term cycling stability of C/S composites but only at relatively low rate (0.2 C). Once the current density increases, the pore effect completely disappears and all Li-S batteries show similar trend of capacity degradation regardless of the different carbon hosts used in the cathodes. The reason has been assigned to the formation of reduced amount of irreversible Li2S on the cathode as well as shortened time for polysulfides to transport towards lithium anode at elevated current densities. This work provides valuable information for predictive selection on carbon materials to construct C/S composite for practical applications from the electrochemical point of view.

Environmental Molecular Sciences Laboratory↗

Revisiting the Role of Conductivity and Polarity of Host Materials for Long-Life Lithium–Sulfur Battery

Despite their high theoretical energy density and low cost, lithium-sulfur batteries (LSBs) suffer from poor cycle life and low energy efficiency owing to the polysulfides shuttle and the electronic insulating nature of sulfur. Conductivity and polarity are two critical parameters for the search of optimal sulfur host materials. However, their role in immobilizing polysulfides and enhancing redox kinetics for long-life LSBs are not fully understood. In this work we have conducted an evaluation on the role of polarity over conductivity by using a polar but nonconductive platelet ordered mesoporous silica (pOMS) and its replica platelet ordered mesoporous carbon (pOMC), which is conductive but nonpolar. It is found that the polar pOMS/S cathode with a sulfur mass fraction of 80 wt% demonstrates outstanding long-term cycle stability for 2000 cycles even at a high current density of 2C. Furthermore, the pOMS/S cathode with a high sulfur loading of 6.5 mg cm -2 illustrates high areal and volumetric capacities with high capacity retention. Complementary physical and electrochemical probes clearly show that surface polarity and structure are more dominant factors for sulfur utilization efficiency and long-life, while the conductivity can be compensated by the conductive agent involved as a required electrode material during electrode preparation. The present findings shed new light on the design principles of sulfur hosts towards long-life and highly efficient LSBs.

25 ENERGY STORAGE↗

Production of C 2 /C 3 Oxygenates from Planar Copper Nitride-Derived Mesoporous Copper via Electrochemical Reduction of CO 2

Electrochemical reduction of CO 2 provides an opportunity to produce fuels and chemicals in a carbon-neutral manner, assuming that CO 2 can be captured from the atmosphere. To do so requires efficient, selective, and stable catalysts. In this study, we report a highly mesoporous metallic Cu catalyst prepared by electrochemical reduction of thermally nitrided Cu foil. Under aqueous saturated CO 2 reduction conditions, the Cu 3 N-derived Cu electrocatalyst produces virtually no CH 4 , very little CO, and exhibits a faradaic efficiency of 68% in C 2+ products (C 2 H 4 , C 2 H 5 OH, and C 3 H 7 OH) at a current density of ~18.5 mA cm –2 and a cathode potential of -1.0 V versus the reversible hydrogen electrode. Under these conditions, the catalyst produces more oxygenated products than hydrocarbons. We show that surface roughness is a good descriptor of catalytic performance. The roughest surface reached 98% CO utilization efficiency for C 2+ product formation from CO 2 reduction and the ratio of oxygenated to hydrocarbon products correlates with the degree of surface roughness. These effects of surface roughness are attributed to the high population of undercoordinated sites as well as a high pH environment within the mesopores and adjacent to the surface of the catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ catalyst activation and regeneration enable energy-efficient high-current CO 2 reduction to ethanol-rich C 2+ mixtures

Electrochemical conversion of dissolved CO 2 in bicarbonate electrolytes, i.e., bicarbonate electrolysis, offers distinct advantages over gas diffusion electrode systems by enabling direct utilization of the CO 2 capture electrolyte while bypassing the energy-intensive CO 2 release step. However, bicarbonate electrolysis faces challenges such as CO 2 mass-transfer limitation, local pH-driven CO 2 depletion, and high cathodic potentials. The higher potential often causes catalyst surface reorganization, leading to a gradual loss of active sites and variations in selectivity during CO 2 reduction. Here, we report a directed, in situ activation and regeneration method that allows precatalysts to equilibrate under dynamic (pulsed) electrolysis conditions. We demonstrate in situ activation of a scalable Cu 2 O/Cu mesh that, under short-width (t = 4 s) pulsed electrolysis, provides stable mixed oxidation states of Cu, favoring the formation of an ethanol-rich crude mixture. The pulsed electrolysis waveform, consisting of six distinct segments, is tuned to form Cu + oxides, which are then reduced to generate local alkaline conditions favoring C–C coupling. This synergistic effect results in FEs of 73% for C2+ products and 39% for ethanol at an applied current density of −150 mA cm −2 and a cathodic potential of −1.45 V (vs. RHE). The overall half-cell energy efficiency is ∼30% for C 2+ products. The in situ Raman experiments confirm the role of pCO 2 R in dynamically regenerating Cu+-containing surface species during pulsed operation, thereby steering selectivity towards C 2+ products. A comprehensive multiscale, multiphysics model is developed to investigate the dynamic behavior of copper surface species (Cu, Cu + , and Cu 2+ ) and local microenvironmental conditions during the pCO 2 R. The results reveal that the coexistence of different copper oxidation states, especially the Cu+ intermediate, is critical in steering selectivity towards multicarbon (C 2+ ) products. The dynamic modulation of surface redox states via tailored pulsing strategies favors C–C coupling pathways by inducing localized alkaline conditions and stabilizing reactive intermediates. This work establishes a predictive modeling platform that links pulse waveform design with mechanistic insights into catalyst state evolution and product selectivity. Overall, this study provides valuable insights into the synergistic effect of in situ activation of pre-catalysts and pulsed electrolysis for higher selectivity towards C 2+ products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemical process for the preparation of nitrogen fertilizers

The present invention provides methods and apparatus for the preparation of nitrogen fertilizers including ammonium nitrate, urea, urea-ammonium nitrate, and/or ammonia, at low temperature and pressure, preferably at ambient temperature and pressure, utilizing a source of carbon, a source of nitrogen, and/or a source of hydrogen or hydrogen equivalent. Implementing an electrolyte serving as ionic charge carrier, (1) ammonium nitrate is produced via the reduction of a nitrogen source at the cathode and the oxidation of a nitrogen source at the anode; (2) urea or its isomers are produced via the simultaneous cathodic reduction of a carbon source and a nitrogen source; (3) ammonia is produced via the reduction of nitrogen source at the cathode and the oxidation of a hydrogen source or a hydrogen equivalent such as carbon monoxide or a mixture of carbon monoxide and hydrogen at the anode; and (4) urea-ammonium nitrate is produced via the simultaneous cathodic reduction of a carbon source and a nitrogen source, and anodic oxidation of a nitrogen source. The electrolyte can be aqueous, non-aqueous, or solid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Voltage Charging-Induced Strain, Heterogeneity, and Micro-Cracks in Secondary Particles of a Nickel-Rich Layered Cathode Material

Nickel-rich layered materials LiNi 1-x-y Mn x Co y O 2 are promising candidates for high-energy-density lithium-ion battery cathodes. Unfortunately, they suffer from capacity fading upon cycling, especially with high-voltage charging. It is critical to have a mechanistic understanding of such fade. Synchrotron-based techniques (including scattering, spectroscopy, and microcopy) and finite element analysis are utilized to understand the LiNi 0.6 Mn 0.2 Co 0.2 O 2 material from structural, chemical, morphological, and mechanical points of view. The lattice structural changes are shown to be relatively reversible during cycling, even when 4.9 V charging is applied. However, local disorder and strain are induced by high-voltage charging. Nano-resolution 3D transmission X-ray microscopy data analyzed by machine learning methodology reveal that high-voltage charging induced significant oxidation state inhomogeneities in the cycled particles. Regions at the surface have a rock salt–type structure with lower oxidation state and build up the impedance, while regions with higher oxidization state are scattered in the bulk and are likely deactivated during cycling. In addition, the development of micro-cracks is highly dependent on the pristine state morphology and cycling conditions. Hollow particles seem to be more robust against stress-induced cracks than the solid ones, suggesting that morphology engineering can be effective in mitigating the crack problem in these materials.

25 ENERGY STORAGE↗

An Aqueous Ca‐Ion Battery

Abstract Multivalent‐ion batteries are emerging as low‐cost, high energy density, and safe alternatives to Li‐ion batteries but are challenged by slow cation diffusion in electrode materials due to the high polarization strength of Mg‐ and Al‐ions. In contrast, Ca‐ion has a low polarization strength similar to that of Li‐ion, therefore a Ca‐ion battery will share the advantages while avoiding the kinetics issues related to multivalent batteries. However, there is no battery known that utilizes the Ca‐ion chemistry due to the limited success in Ca‐ion storage materials. Here, a safe and low‐cost aqueous Ca‐ion battery based on a highly reversible polyimide anode and a high‐potential open framework copper hexacyanoferrate cathode is demonstrated. The prototype cell shows a stable capacity and high efficiency at both high and low current rates, with an 88% capacity retention and an average 99% coloumbic efficiency after cycling at 10C for 1000 cycles. The Ca‐ion storage mechanism for both electrodes as well as the origin of the fast kinetics have been investigated. Additional comparison with a Mg‐ion cell with identical electrodes reveals clear kinetics advantages for the Ca‐ion system, which is explained by the smaller ionic radii and more facile desolvation of hydrated Ca‐ions.

25 ENERGY STORAGE↗

Two Artificial Leaf Architectures for Solar Formate Production From CO 2 and H 2 O

Sunlight-powered artificial leaves for the production of formate from CO 2 are an attractive route to solar fuels, yet existing solar formate devices remain low in performance, and their architecture and material choices are underexplored. Herein, we report the fabrication of two distinct fully integrated, self-standing solar formate device architectures and elucidate the underlying design principles and material selection strategies. The first architecture integrates a Si photocathode with a BiVO 4 photoanode and utilizes a highly active Pd catalyst for CO 2 reduction. It represents the first artificial leaf device comprising two photoelectrodes (excluding photovoltaic [PV]-biased electrodes) for effective formate production under single-beam illumination. The second architecture employs a dark cathode and a dark anode driven by a 4-junction perovskite solar cell and uses a highly stable Bi catalyst for CO 2 reduction. This device delivers a record-high formate production rate of 174 µmol h −1 with a remarkable solar-to-formate energy efficiency of 2% among all artificial leaf devices reported to date. Finally, these results demonstrate the feasibility and outline the design principles of both PV-free and PV-assisted device architectures in solar fuel production.

electrocatalysis↗

Li/Ag 2 VO 2 PO 4 batteries: the roles of composite electrode constituents on electrochemistry

In this study, we utilize silver vanadium phosphorous oxide, Ag 2 VO 2 PO 4 , as a model system to systematically study the impact of the constituents of a composite electrode, including polymeric and conductive additives, on electrochemistry. Notably, although highly resistive, this bimetallic cathode can be discharged as a pure electroactive material in the absence of a conductive additive as it generates an in situ conductive matrix via a reduction displacement reaction resulting in the formation of silver metal nanoparticles. Also, three different electrode compositions were investigated: Ag 2 VO 2 PO 4 only, Ag 2 VO 2 PO 4 4 with binder, and Ag 2 VO 2 PO 4 with binder and carbon. Constant current discharge, pulse testing and impedance spectroscopy measurements were used to characterize the electrochemical properties of the electrodes as a function of depth of discharge. In situ EDXRD was used to spatially resolve the discharge progression within the cathode by following the formation of Ag 0 . Ex situ XRD and EXAFS modeling were used to quantify the amount of Ag 0 formed. Results indicate that the metal center reduced (V 5+ or Ag + ) was highly dependent on composite composition (presence of PTFE, carbon), depth of discharge (Ag 0 nanoparticle formation), and spatial location within the cathode. The addition of a binder was found to increase cell polarization, and the percolation network provided by the carbon in the presence of PTFE was further increased with reduction and formation of Ag 0 . Lastly, this study provides insight into the factors controlling the electrochemistry of resistive active materials in composite electrodes.

25 ENERGY STORAGE↗

Application of electrostatic Langmuir probe to atmospheric arc plasmas producing nanostructures

The temporal evolution of a high pressure He arc producing nanotubes was considered and the Langmuir probe technique was applied for plasma parameter measurements. Two modes of arc were observed: cathodic arc where discharge is supported by erosion of cathode material and anodic arc which is supported by ablation of the anode packed with carbon and metallic catalysts in which carbon nanotubes are synthesized. Voltage-current (V-I) characteristics of single probes were measured and unusually low ratio of saturation current on positively biased probe to that on negatively biased of about 1-4 was observed. This effect was explained by increase of measured current at the negatively biased probe above the level of ion saturation current due to secondary electron emission from the probe surface. Since utilization of standard collisionless approach to determine plasma parameters from the measured V-I characteristic is not correct, the electron saturation current was used to estimate the plasma density.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Description of the novel perchlorate-reducing bacteria Dechlorobacter hydrogenophilus gen. nov., sp. nov. and Propionivibrio militaris , sp. nov.

Novel dissimilatory perchlorate-reducing bacteria (DPRB) were isolated from enrichments conducted under conditions different from those of all previously described DPRB. Strain LT-1 T was enriched using medium buffered at pH 6.6 with 2-(N-morpholino)ethanesulfonic acid (MES) and had only 95% 16S rRNA gene identity with its closest relative, Azonexus caeni. Strain MP T was enriched in the cathodic chamber of a perchlorate-reducing bioelectrical reactor (BER) and together with an additional strain, CR (99% 16S rRNA gene identity), had 97% 16S rRNA gene identity with Propionivibrio limicola. The use of perchlorate and other electron acceptors distinguished strains MP T and CR from P. limicola physiologically. Strain LT-1 T had differences in electron donor utilization and optimum growth temperatures from A. caeni. Strains LT-1 T and MP(T) are the first DPRB to be described in the Betaproteobacteria outside of the Dechloromonas and Azospira genera. On the basis of phylogenetic and physiological features, strain LT-1 T represents a novel genus in the Rhodocyclaceae; strain MP T represents a novel species within the genus Propionivibrio. The names Dechlorobacter hydrogenophilus gen. nov., sp. nov and Propionivibrio militaris sp. nov. are proposed.

59 BASIC BIOLOGICAL SCIENCES↗

Layered Transition Metal Oxides as Ca Intercalation Cathodes: A Systematic First-Principles Evaluation

Finding high-voltage Ca cathode materials is a critical step to unleashing the full potential of high-energy-density Ca-ion batteries. Therefore, first-principles calculations are used to demonstrate that P-type layered calcium transition metal (TM) oxide materials (CaTM 2 O 4 ) with a range of TM substitutions (TM = Ti, V, Cr, Mn, Fe, Co, and Ni) have excellent battery-related properties including thermodynamic stability, average voltage, energy density, synthesizability, ionic mobility, and electronic structure. However, the thermodynamic stability of the charged phase and TM redox activity are shown to be sensitive to TM selection, with CaCo 2 O 4 having the best balance of all considered properties. The utility of combining multiple TMs to expand the chemical search space for TM substitutions is demonstrated by mixing Co and Ni in layered CaTM 2 O 4 .

25 ENERGY STORAGE↗

Multisource inverse-geometry CT. Part II. X-ray source design and prototype

Purpose: This paper summarizes the development of a high-power distributed x-ray source, or “multisource,” designed for inverse-geometry computed tomography (CT) applications [see B. De Man et al., “Multisource inverse-geometry CT. Part I. System concept and development,” Med. Phys. 43, 4607–4616 (2016)]. The paper presents the evolution of the source architecture, component design (anode, emitter, beam optics, control electronics, high voltage insulator), and experimental validation. Methods: Dispenser cathode emitters were chosen as electron sources. A modular design was adopted, with eight electron emitters (two rows of four emitters) per module, wherein tungsten targets were brazed onto copper anode blocks—one anode block per module. A specialized ceramic connector provided high voltage standoff capability and cooling oil flow to the anode. A matrix topology and low-noise electronic controls provided switching of the emitters. Results: Four modules (32 x-ray sources in two rows of 16) have been successfully integrated into a single vacuum vessel and operated on an inverse-geometry computed tomography system. Dispenser cathodes provided high beam current (>1000 mA) in pulse mode, and the electrostatic lenses focused the current beam to a small optical focal spot size (0.5 × 1.4 mm). Controlled emitter grid voltage allowed the beam current to be varied for each source, providing the ability to modulate beam current across the fan of the x-ray beam, denoted as a virtual bowtie filter. The custom designed controls achieved x-ray source switching in <1 μs. The cathode-grounded source was operated successfully up to 120 kV. Conclusions: A high-power, distributed x-ray source for inverse-geometry CT applications was successfully designed, fabricated, and operated. Future embodiments may increase the number of spots and utilize fast read out detectors to increase the x-ray flux magnitude further, while still staying within the stationary target inherent thermal limitations.

60 APPLIED LIFE SCIENCES↗

Effect of Concentration, Temperature, and Interelectrode Gap on the Voltage Drop in an Electrochemical System of GdCl{sub 3}-LiCl-KCl

One of the most common conversations for those in the nuclear field and the public when discussing nuclear power is the issue of nuclear waste. When used nuclear fuel (UNF) is removed from a reactor, it contains fission products, some of which are long lived isotopes that will continue to irradiate for hundreds of years. One of several solutions to this issue is reprocessing, a process where minor actinides and other fission products are separated from still fissile and fertile materials. In the United States, there is no reprocessing of UNF at an industrial scale; however, one of the methods that universities and national labs are currently researching is known as pyro-processing. Pyro-processing utilizes electrochemistry in a molten salt environment to treat UNF and remove uranium and plutonium. The heart of the pyro-processing system is an electrorefining process, where most of the U in the UNF is selectively collected on a solid cathode in molten lithium-potassium chloride (LiCl-KCl) at high temperatures (723 K - 773 K). To model the behavior of materials in the electro-refiner, small bench-scale electrochemical experiments are being performed at many research universities and national labs to better understand material behavior. Within the electrochemical cell, there is a small resistance to current between the cathode and anode. This results in a voltage drop, which can affect the results of the experiments. This voltage drop varies based upon concentration of the salt, the temperature, the distance between the anode and cathode, and the scan rate. For this study, cyclic voltammetry will be performed on GdCl{sub 3}-LiCl-KCl at various temperatures (723 K - 798 K), various sample concentrations (1, 5, and 10 wt%), various scan rates (50, 100, 200, and 300 mV/s), and two different electrode spacing configurations. The resulting cyclic voltammograms will be compared for both electrode configurations to see the impact of interelectrode gap on the voltage drop.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Continuous production of pure liquid fuel solutions via electrocatalytic CO 2 reduction using solid-electrolyte devices

Electrocatalytic CO 2 reduction is often carried out in a solution electrolyte such as KHCO 3 (aq), which allows for ion conduction between electrodes. Thus, liquid products that form are in a mixture with the dissolved salts, requiring energy-intensive downstream separation. In this work, we report continuous electrocatalytic conversion of CO 2 to pure liquid fuel solutions in cells that utilize solid electrolytes, where electrochemically generated cations (such as H+) and anions (such as HCOO–) are combined to form pure product solutions without mixing with other ions. Using a HCOOH-selective (Faradaic efficiencies>90%) and easily scaled Bi catalyst at the cathode, we demonstrate production of pure HCOOH solutions with concentrations up to 12M. We also show 100h continuous and stable generation of 0.1 M HCOOH with negligible degradation in selectivity and activity. Production of other electrolyte-free C 2+ liquid oxygenate solutions, including acetic acid, ethanol and n-propanol, are also demonstrated using a Cu catalyst. Lastly, we show that our CO 2 reduction cell with solid electrolytes can be modified to suit other, more complex practical applications.

36 MATERIALS SCIENCE↗