Search NASA⌕ Search

SEARCH · Search NASA

Results for “curing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Effect of thermal spike on composite moisture capacity

As part of a continuing study of the effects of thermal spike on composite physical properties, severals sets of 16-ply TGDDM-DDS epoxy/graphite fiber composites were first saturated with moisture, and then individual specimens were subjected to thermal spikes of up to 240 C for periods of up to 25 minutes. At the cure temperature, 177 C, all sets show a change in rate of mass lost during spike. Post-spike moisture reabsorption capacity data provides evidence of temperature dependent molecular structural dilation and consolidation of the epoxide matrix. This evidence suggests that either a thermoreversible phenomenon such as physical aging or a nonreversible additional cure becomes active near the upper limit of the aircraft supersonic flight profile. These and other important observations suggest that one or more of several mechanisms may be active during thermal spike.

Adamson, M. J.↗
NASA NTRS1989

Process modeling for carbon-phenolic nozzle materials

A thermochemical model based on the SINDA heat transfer program is developed for carbon-phenolic nozzle material processes. The model can be used to optimize cure cycles and to predict material properties based on the types of materials and the process by which these materials are used to make nozzle components. Chemical kinetic constants for Fiberite MX4926 were determined so that optimization of cure cycles for the current Space Shuttle Solid Rocket Motor nozzle rings can be determined.

Letson, Mischell A.↗
NASA NTRS1986

Laminar flow control perforated wing panel development

Many structural concepts for a wing leading edge laminar flow control hybrid panel were analytically investigated. After many small, medium, and large tests, the selected design was verified. New analytic methods were developed to combine porous titanium sheet bonded to a substructure of fiberglass and carbon/epoxy cloth. At -65 and +160 F test conditions, the critical bond of the porous titanium to the composite failed at lower than anticipated test loads. New cure cycles, design improvements, and test improvements significantly improved the strength and reduced the deflections from thermal and lateral loadings. The wave tolerance limits for turbulence were not exceeded. Consideration of the beam column midbay deflections from the combinations of the axial and lateral loadings and thermal bowing at -65 F, room temperature, and +160 F were included. Many lap shear tests were performed at several cure cycles. Results indicate that sufficient verification was obtained to fabricate a demonstration vehicle.

Fischler, J. E.↗
NASA NTRS1987

Low cost tooling material and process for graphite and Kevlar composites

An Extruded Sheet Tooling Compound (ESTC) was developed for use in quickly building low cost molds for fabricating composites. The ESTC is a very highly mineral-filled resin system formed into a 6 mm thick sheet. The sheet is laid on the pattern, vacuum (bag) is applied to remove air from the pattern surface, and the assembly is heat cured. The formed ESTC is then backed and/or framed and ready for use. The cured ESTC exhibits low coefficient of thermal expansion and maintains strength at temperatures of 180 to 200 C. Tools were made and used successfully for: Compression molding of high strength epoxy sheet molding compound, stamping of aluminum, resin transfer molding of polyester, and liquid resin molding of polyester. Several variations of ESTC can be made for specific requirements. Higher thermal conductivity can be achieved by using an aluminum particle filler. Room temperature gel is possible to allow use of foam patterns.

Childs, William I.↗
NASA NTRS1990

Autoclavable addition polyimides for 371 C composite applications

Studies were conducted to improve the thermo-oxidative stability (TOS) of PMR type polyimides by the substitution of para-aminostyrene (PAS) for the nadic ester endcap in second generation PMR polyimides (PMR-2). The nadic endcap which provides the PMR polyimides with their relative ease of fabrication, both by limiting the molecular weight of the prepolymer and by undergoing the final addition cure without volatiles, is also the weak link with regard to TOS. A polyimide formulated with PAS endcaps, called V-CAP, utilizes a two step reaction sequence similar to that of the PMR polyimides and can be easily autoclave molded into low void composite materials. Resin studies included two formulations of both PMR-2 and V-CAP, corresponding to n=9 and n=14 prepolymer stoichiometry. Unidirectional reinforced T40R graphite fiber laminates were fabricated from each of the resins was post-cured in either air at 385 C or nitrogen at 400 C. Composite specimens were aged in air at 371 C and mechanical properties were measured at 371 C before and after exposure.

Vannucci, R. D.↗
NASA NTRS1989

Smart structures research program at Virginia Tech

A review of the smart structures and avionics research and teaching program that started in 1979 at Virginia Tech is described. Current smart structures research include major efforts in the development of embedded and attached optical fiber and acoustic fiber sensors for cure monitoring, in-service lifetime structural testing, nondestructive evaluation, and impact and damage detection and analysis; of gradual material degradation; sensor signal multiplexing, processing and data handling to achieve near real-time distributed structural analysis; and the integration of embedded sensors, actuators and control electronics to achieve controlled structural response. Special campus facilities used for this work include an optical fiber fabrication facility, an autoclave for composite structure fabrication and curing, and laboratories for optical fiber sensor development, materials response and nondestructive evaluation, structural control testing and computer engineering.

Claus, R. O.↗
NASA NTRS1990

Fiber optic smart structures and skins II; Proceedings of the Meeting, Boston, MA, Sept. 5-8, 1989

The present conference on embedded fiber-optics incorporating 'smart' structural systems and structural surfaces discusses topics in the nature and current status of university- and government-sponsored smart-structure development programs, manufacturing and cure-monitoring for composite smart structures, smart-structure damage assessment, smart-structure actuators, and smart-structure sensors and components. Attention is given to fiber-optic sensor selection, the optical properties of curing epoxies, the automated production of smart structures, damage-detection in composites with embedded fiber-optic interferometers, fiber-optic strain and impact sensors, dynamically-tunable smart composites, smart structures incorporating artificial neural networks, active structural acoustic control with smart structures, and fiber-optic shape sensing for flexible structures.

Udd, Eric↗
NASA NTRS1991

Relationship between voids and interlaminar shear strength of polymer matrix composites

The effect of voids on the interlaminar shear strength of a polyimide matrix composite system is described. The AS4 graphite/PMR-15 composite was chosen for study because this system can be readily processed by using the standard specified cure cycle to produce void-free composites and because preliminary work in this study had shown that the processing parameters of this resin matrix system can be altered to produce cured composites of varying void contents. Thirty-eight 12-ply unidirectional composite panels were fabricated for this study. A significant range of void contents (0 to 10 percent) was produced. The panels were mapped, ultrasonically inspected, and sectioned into interlaminar shear, flexure, and fiber content specimens. The density of each specimen was measured and interlaminar shear and flexure strength measurements were then made. The fiber content was measured last. The results of these tests were evaluated by using ultrasonic results, photomicrographs, statistical methods, theoretical relationships derived by other investigators, and comparison of the test data with the Integrated Composite Analyzer (ICAN) computer program developed at the Lewis Research Center for predicting composite ply properties. The testing is described in as much detail as possible in order to help others make realistic comparisons.

Bowles, Kenneth J.↗
NASA NTRS1989

The University of Arizona program in solid propellants

The University of Arizona program is aimed at introducing scientific rigor to the predictability and quality assurance of composite solid propellants. Two separate approaches are followed: to use the modern analytical techniques to experimentally study carefully controlled propellant batches to discern trends in mixing, casting, and cure; and to examine a vast bank of data, that has fairly detailed information on the ingredients, processing, and rocket firing results. The experimental and analytical work is described briefly. The principle findings were that: (1) pre- (dry) blending of the coarse and fine ammonium perchlorate can significantly improve the uniformity of mixing; (2) the Fourier transformed IR spectra of the uncured and cured polymer have valuable data on the state of the fuel; (3) there are considerable non-uniformities in the propellant slurry composition near the solid surfaces (blades, walls) compared to the bulk slurry; and (4) in situ measurements of slurry viscosity continuously during mixing can give a good indication of the state of the slurry. Several important observations in the study of the data bank are discussed.

Ramohalli, Kumar↗
NASA NTRS1990

Filament winding cylinders. III - Selection of the process variables

By using the Lee-Springer filament winding model temperatures, degrees of cure, viscosities, stresses, strains, fiber tensions, fiber motions, and void diameters were calculated in graphite-epoxy composite cylinders during the winding and subsequent curing. The results demonstrate the type of information which can be generated by the model. It is shown, in reference to these results, how the model, and the corresponding WINDTHICK code, can be used to select the appropriate process variables.

Lee, Soo-Yong↗
NASA NTRS1990

Acetylene-chromene terminated resins as high temperature thermosets

A novel phase transfer catalyzed process for the preparation of propargyl ethers has been developed. The propargyl ethers serve as precursors to a new class of thermosetting resins called acetylene-chromene terminated (ACT) resins. Heat treatment of a solution of propargyl ethers with various catalysts, followed by removal of solvent leads to the ACT resins via partial conversion of the propargyl ether groups to chromenes. This process reduces the energy content of the resin systems and reduces the amount of shrinkage found during cure. Due to the presence of the solvent the process is safe and gives rise to low viscosity products suitable for resin transfer molding and filament winding type applications. Due to the high glass transition temperature, high modulus, and low moisture uptake the cured resins display better than 232 C/wet performance. The thermal stability of the ACT resins in air at 204 C is superior to that of conventional bismaleimide resins. The resins also display excellent electrical properties.

Godschalx, J. P.↗
NASA NTRS1990

Autoclavable addition polyimides for 371 C composite applications

Studies were conducted to improve the thermo-oxidative stability (TOS) of PMR type polyimides by the substitution of para-aminostyrene (PAS) for the nadic ester endcap in second generation PMR polyimides (PMR-2). The nadic endcap which provides the PMR polyimides with their relative ease of fabrication, both by limiting the molecular weight of the prepolymer and by undergoing the final addition cure without volatiles, is also the weak link with regard to TOS. A polyimide formulated with PAS endcaps, called V-CAP, utilizes a two step reaction sequence similar to that of the PMR polyimides and can be easily autoclave molded into low void composite materials. Resin studies included two formulations of both PMR-2 and V-CAP, corresponding to n = 9 and n = 14 prepolymer stoichiometry. Unidirectional reinforced T40R graphite fiber laminates were fabricated from each of the resins was post-cured in either air at 385 C or nitrogen at 400 C. Composite specimens were aged in air at 371 C and mechanical properties were measured at 371 C before and after exposure.

Vannucci, R. D.↗
NASA NTRS1991

Spectroscopy and multivariate analyses applications related to solid rocket nozzle bondline

Chemical composition and molecular orientation define the properties of materials. Information related to chemical composition and molecular configuration is obtained by various forms of spectroscopy. Software algorithms developed for multivariate analyses, expert systems, and Artificial Intelligence (AI) are used to conduct repetitive operations. The techniques are believed to be of particular significance toward achieving TQM objectives. The objective was to obtain information related to the quality of the bondline in the solid rocket motor, SRM, nozzle. Hysol 934 NA, a room temperature curing epoxide resin, is used as the bonding agent. A good bond requires that the adhesive be placed on a properly prepared metal surface, the adhesives Part A and B be mixed in appropriate ratio from material within shelf life specifications. Spectroscopic data was obtained for surfaces prepared according to specifications, contaminated metal surfaces, samples of the epoxide adhesive at times that represent shelf aging from 3 months to 2 years, several mix ratio of A to B, and curing material. Temperature was found to be a significant factor. The study concentrated on pot life and mix ratio.

Arendale, W. F.↗
NASA NTRS1989

The Father Christmas worm

Given here is an overview analysis of the Father Christmas Worm, a computer worm that was released onto the DECnet Internet three days before Christmas 1988. The purpose behind the worm was to send an electronic mail message to all users on the computer system running the worm. The message was a Christmas greeting and was signed 'Father Christmas'. From the investigation, it was determined that the worm was released from a computer (node number 20597::) at a university in Switzerland. The worm was designed to travel quickly. Estimates are that it was copied to over 6,000 computer nodes. However, it was believed to have executed on only a fraction of those computers. Within ten minutes after it was released, the worm was detected at the Space Physics Analysis Network (SPAN), NASA's largest space and Earth science network. Once the source program was captured, a procedural cure, using the existing functionality of the computer operating systems, was quickly devised and distributed. A combination of existing computer security measures, the quick and accurate procedures devised to stop copies of the worm from executing, and the network itself, were used to rapidly provide the cure. These were the main reasons why the worm executed on such a small percentage of nodes. This overview of the analysis of the events concerning the worm is based on an investigation made by the SPAN Security Team and provides some insight into future security measures that will be taken to handle computer worms and viruses that may hit similar networks.

Green, James L.↗
NASA NTRS1990

Residual strength of repaired graphite/epoxy laminates after 5 years of outdoor exposure

The NASA Langley Research Center has sponsored research to develop generic repair techniques and processes for advanced graphite/epoxy (Gr/Ep) composites applicable to secondary structures for commercial transport aircraft. The long-term durability of such repairs is being addressed in a 10-year outdoor exposure program at the Langley Research Center. Details of the program and results of residual strength tests after 5 years of outdoor exposure are presented. Four repair methods are being evaluated. These include: (1) externally bolted aluminum-plus adhesive; (2) precured, bonded external Gr/Ep; (3) cure-in-place external Gr/Ep; and (4) cure-in-place flush Gr/Ep. Repaired specimens as well as undamaged and damaged unrepaired controls are being exposed outdoors for 1, 3, 5, 7, and 10 years. The residual tensile strength of stressed, unstressed, and fatigue specimens from each group is reported and compared with the tensile strength of baseline specimens which received no outdoor exposure. Identification of the commercial products and companies is used to describe adequately the test materials. The identification of these commercial products does not constitute endorsement, expressed or implied, of such products by the National Aeronautics and Space Administration.

Deaton, Jerry W.↗
NASA NTRS1992

Flush mounting of thin film sensors

Flush mounting of a sensor on a surface is provided by first forming a recessed area on the surface. Next, an adhesive bonding mixture is introduced into the recessed area. The adhesive bonding mixture is chosen to provide thermal expansion matching with the surface surrounding the recessed area. A strip of high performance polymeric tape is provided, with the sensor attached to the underside thereof, and the tape is positioned over the recessed area so that it acts as a carrier of the sensor. A shim having flexibility so that it will conform to the surface surrounding the recessed area is placed over the tape, and a vacuum pad is placed over the shim. The area above the surface is then evacuated while holding the sensor flush with the surface during curing of the adhesive bonding mixture. After such curing, the pad, shim, and tape are removed from the sensor, electrical connections for the sensor are provided, after which the remaining space in the recessed area is filled with a polymeric foam.

Moore, Thomas C., Sr.↗
NASA NTRS1991

Chemistry and properties of blends of acetylene terminated materials

As part of a NASA program to develop new high temperature/high performance structural materials, the chemistry and properties of acetylene-containing materials and their cured resins are under investigation. The objective of this work is to develop materials that are readily processable (i.e., 200-300 C and about 1.4 MPa or less) and possess usable mechanical properties at temperatures as high as 177 C. An acetylene-terminated aspartimide (ATA) was blended with an equal weight of an acetylene-terminated arylene ether (ATAE) oligomer. The blend was subsequently thermally cured to yield a resin which was evaluated in the form of neat resin moldings, adhesive specimens, and laminates. Adhesive specimens and laminates gave good mechanical properties to temperatures as high as 177 C. In addition, preliminary laminate work is presented on the resin from a blend of a new N-methyl substituted ATA and an ATAE.

Connell, John W.↗
NASA NTRS1991

Sensor-model in-situ control of the RTM composite process

The paper reports on the use of in situ frequency dependent electromagnetic sensors (FDEMS) and the Loos resin transfer model to select and control the processing properties of an epoxy resin during RTM impregnation and cure. Once correlated with viscosity and degree of cure, FDEMS monitors the advancement of the resin, viscosity, and the impregnation of the fabric, allowing a direct means of monitoring in situ in the mold throughout the fabrication process the effects of time, temperature, vacuum, and pressure.

Kranbuehl, D. E.↗