Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron backscattered diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Effect of Different Thermomechanical Processes on the Microstructure, Texture, and Mechanical Properties of API 5L X70 Steel

A commercial API 5L X70 steel plate was subjected to different thermomechanical processes to propose a novel thermomechanical rolling path to achieve improved mechanical properties. Scanning electron microscopy, electron backscatter diffraction, and x-ray texture analysis were employed for microstructural characterization. The results showed that strain-free recrystallized {001} ferrite grains that developed at higher rolling temperature could not meet the American Petroleum Institute (API) requirements. Also, refined and work-hardened grains that have formed in the intercritical region with high stored energy do not provide suitable tensile properties. However, fine martensite–austenite constituents dispersed in ferrite matrix with grains having predominantly {111} and {110} orientations parallel to the normal direction that developed under isothermal rolling at 850 °C provided an outstanding combination of tensile strength and ductility.

36 MATERIALS SCIENCE↗

Preferred orientations of laterally grown silicon films over amorphous substrates using the vapor–liquid–solid technique

A novel method has been optimized so that adhesion layers are no longer needed to reliably deposit patterned gold structures on amorphous substrates. Using this technique allows for the fabrication of amorphous oxide templates known as micro-crucibles, which confine a vapor–liquid–solid (VLS) catalyst of nominally pure gold to a specific geometry. Within these confined templates of amorphous materials, faceted silicon crystals have been grown laterally. The novel deposition technique, which enables the nominally pure gold catalyst, involves the undercutting of an initial chromium adhesion layer. Using electron backscatter diffraction it was found that silicon nucleated in these micro-crucibles were 30% single crystals, 45% potentially twinned crystals and 25% polycrystals for the experimental conditions used. Single, potentially twinned, and polycrystals all had an aversion to growth with the (1 0 0) surface parallel to the amorphous substrate. Closer analysis of grain boundaries of potentially twinned and polycrystalline samples revealed that the overwhelming majority of them were of the 60° Σ3 coherent twin boundary type. The large amount of coherent twin boundaries present in the grown, two-dimensional silicon crystals suggest that lateral VLS growth occurs very close to thermodynamic equilibrium. It is suggested that free energy fluctuations during growth or cooling, and impurities were the causes for this twinning.

36 MATERIALS SCIENCE↗

Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone

The microstructure of acicular ferrite and its formation for the grain refinement of coarse-grained region of heat-affected zone of high strength low-alloy bainite steels were studied using three-dimensional reconstruction technique. Crystallographic grain size was analyzed by means of electron backscatter diffraction. It was revealed that the microstructure in the coarse-grained region of the heat-affected zone consisted of predominantly bainite packets and a small proportion of acicular ferrite. Acicular ferrite was of lath or plate-like rather than needle or rod-like morphology. Tempering of the coarse-grained region of heat-affected zone showed that the acicular ferrite was more stable than the bainite, indicating that the acicular ferrite was formed prior to bainite. The acicular ferrite laths or plates divided the prior austenite grains into smaller and separate regions, and confining the bainite transformed at lower temperatures in the smaller regions and hence leading to the grain refinement in the coarse-grained region of the heat-affected zone.

36 MATERIALS SCIENCE↗

Hierarchical Microstructures in CZT

Advanced characterization tools, such as electron backscatter diffraction and transmitted IR microscopy, are being applied to study critical microstructural features and orientation relations in as-grown CZT crystals to aid in understanding the relation between structure and properties in radiation detectors. Even carefully prepared single crystals of CZT contain regions of slight misorientation, Te-particles, and dislocation networks that must be understood for more accurate models of detector response. This paper describes initial research at PNNL into the hierarchy of microstructures observed in CZT grown via the vertical gradient freeze or vertical Bridgman method at PNNL and WSU.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Precipitate Redistribution during Creep of Alloy 617

Nickel-based superalloys are being considered for applications within advanced nuclear power generation systems due to their high temperature strength and corrosion resistance. Alloy 617, a candidate for use in heat exchangers, derives its strength from both solid solution strengthening and the precipitation of carbide particles. However, during creep, carbides that are supposed to retard grain boundary motion are found to dissolve and re-precipitate on boundaries in tension. To quantify the redistribution, we have used electron backscatter diffraction and energy dispersive spectroscopy to analyze the microstructure of 617 after creep testing at 900 and 1000°C. The data were analyzed with respect to location of the carbides (e.g., intergranular vs. intragranular), grain boundary character, and precipitate type (i.e., Cr-rich or Mo-rich). We find that grain boundary character is the most important factor in carbide distribution; some evidence of preferential distribution to boundaries in tension is also observed at higher applied stresses. Finally, the results suggest that the observed redistribution is due to the migration of carbides to the boundaries and not the migration of boundaries to the precipitates.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The effect of microstructure on the relationship between grain boundary sliding and slip transmission in high purity aluminum

The relationship between grain boundary sliding (GBS) and slip transmission is investigated experimentally at grain boundaries in 99.99% aluminum with a through-thickness, coarse grained microstructure deformed in tension at 190 °C. Using scanning electron microscope enabled digital image correlation (SEM-DIC) and electron backscatter diffraction (EBSD), high resolution strain fields and microstructural information were measured to examine the influence of microstructural neighborhoods on interactions between GBS and slip transmission and strain localization. Several distinct cases are presented that highlight important microstructural factors that govern deformation near grain boundaries. The findings include (1) direct transmission and GBS were anti-compatible and facilitated by opposing boundary types (low misorientation and high energy grain boundaries respectively); (2) increased GBS activity was correlated with decreased indirect transmission behavior; (3) GBS accommodation at triple junctions was enabled by intragranular plasticity; and (4) the local intragranular plastic strain discontinuity between grains determined the magnitude of GBS gradients. Finally, this work provides insight into the nature of these mechanisms and can be used to identify strain transfer criteria that can lead to improved GBS-sensitive crystal plasticity models.

36 MATERIALS SCIENCE↗

Experimental tests of stereological estimates of grain boundary populations

We present experimental validation of a method for estimating three-dimensional (3-D) relative numerical populations of grain boundaries from measurements of individual two-dimensional (2-D) cross-sections. Such numerical populations are relevant to network topology and the modeling of intergranular failure modes in grain boundary engineered materials, and are distinct from geometrical population measures such as area per volume. We examine 3-D reconstructions of stainless steel and copper, with varying populations of twin-related boundaries, generated by serial-section electron backscatter diffraction and high-energy X-ray diffraction microscopy. We show that 2-D length fractions, 2-D number fractions and 3-D number fractions are all distinct quantities when grain boundary type is correlated with grain boundary size. We also demonstrate that the last quantity may be reliably inferred from the first two, provided the experimental spatial resolution is much finer than the grain size, eliminating the need to use 3-D experimental methods to access at least some information about 3-D network properties. Many of the {Sigma}3 boundaries are extremely complex, with highly re-entrant shapes that can intersect a sample plane many times, giving a false impression of multiple separate boundaries.

36 MATERIALS SCIENCE↗

Effect of grain orientation on mechanical properties and thermomechanical response of Sn-based solder interconnects

The thermomechanical response of Sn-based solder interconnects with differently oriented grains was investigated by electron backscattered diffraction technique under thermal cycling and thermal shock testing in this study. The results showed that deformation and cracking of solder interconnects have a close relationship with the unique characteristics of grain orientation and boundaries in each solder interconnect, and deformation was frequently confined within the high-angle grain boundaries. The micro Vickers hardness testing results showed that the hardness varied significantly depending on the grain orientation and structure, and deformation twins can be induced around the indents by the indentation testing. - Highlights: • Thermomechanical response shows a close relationship with the grain structure. • Deformation was frequently confined within the high-angle grain boundaries. • Different grain orientations exhibit different hardness. • Deformation twins can be induced around the indents in SAC105 solder interconnects.

36 MATERIALS SCIENCE↗

Effect of aging on failure mechanism of Alloy 709 at various temperatures

Alloy 709 is a novel austenitic stainless steel with high temperature creep strength, weldability, and corrosion resistance. These properties make the material suitable for applications in the structure of next-generation nuclear power plants. Enduring high temperatures for an extended period of time in the harsh environments of a nuclear power plant results in thermal aging of the material. Therefore, it is imperative to study the effect of thermal aging on the microstructure and mechanical properties of Alloy 709 before its application in the next generation power plants. In this study, hot-processed (forged + rolled), annealed and quenched ingots of Alloy 709 are aged at 650 °C for 2000 h in air and then tested at various temperatures up to 850 °C in an in-situ heating-loading Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectroscopy (EDS) and Electron Backscatter Diffraction (EBSD). The effect of testing temperature and aging on microstructural evolutions during tensile testing of as-received and aged samples are studied. Furthermore, both as-received and aged samples displayed serrations and drop in ductility at elevated temperatures, due to the effect of dynamic strain aging (DSA). The occurrence of DSA activity was found within temperatures range of 500 °C–750 °C in as-received and 550 °C - 650 °C in aged samples. The aged samples showed less elongation accompanied by shallower dimples on the fractured surface, indicating less ductile failure mechanism compared to as-received samples. Failure mechanism observations on the fracture surface using SEM fractography are correlated to the observations made on the sample surface using in-situ SEM to achieve a complementary set of information to better understand the failure mechanism of this novel alloy.

36 MATERIALS SCIENCE↗

Ultrafine gradient microstructure induced by severe plastic deformation under sliding contact conditions in copper

Highlights: • Sliding contact produces a gradient microstructure by severe plastic deformation. • Nanohardness is increased strongly by grain size and dislocation hardening. • The texture components in the deformed layer correspond to pure shear. • Grain size distribution, boundary misorientation and KAM were analysed. • Strain induced effects compete with crystallisation to determine the microstructure. - Abstract: Sliding contact induces severe plastic deformation (SPD) at the surface of ductile materials and induces a microstructural gradient associated to a significant increase of hardness toward the surface. This gradient allows observing all stages of grain refinement in SPD, as illustrated here by the analysis of polycrystalline electrolytic copper tested in a coaxial tribometer. Materials tested in the cold-rolled state and after annealing were characterised by high-resolution electron backscattering diffraction and nano-indentation. The incremental plastic strain produces an ultrafine microstructure in the top layers, which gradually changes to the original size in unaffected material. In cold-rolled material, an intermediate recrystallised layer is observed. The separation of the Misorientation Angle Distribution (MAD) in a low-angle portion and a high angle portion allows characterising the accumulation of strain induced misorientation, while the Kernel Average Misorientation (KAM) provides information on the evolution of substructure at the finest levels. The results point toward a process where strain-induced effects compete continuously with recrystallisation, except for the surface layer in the cold-rolled material, where dynamic recrystallisation is dominant. Combining the information from KAM and subgrain size distribution, the measured hardness can be explained as a combination of grain size and dislocation hardening.

36 MATERIALS SCIENCE↗

Nano-Deformation Behavior of a Thermally Aged Duplex Stainless Steel Investigated by Nanoindentation, FIB and TEM

Nanoindentation and electron backscattering diffraction were conducted on a thermally aged duplex stainless steel to investigate the effect of crystal orientation on the plastic deformation behavior during indentation testing. Both nanohardness H and indentation modulus E are correlated with the orientation factor averaged over three normal directions of the contact surface. After thermal aging, the orientation dependence of the hardness and indentation modulus in ferrite significantly changed. For both the ferrite and austenite phases, the maximum and minimum values of the hardness and indentation modulus are given by the near-〈111〉 and near-〈001〉-oriented grains, respectively. The TEM analysis results indicate that the area of plastic deformation in the ferrite grain decreases after thermal aging. The interactions between precipitates and dislocations are considered to be responsible for the degradation of plastic deformation ability in ferrite. The anisotropy of hardness is related to the crystallographic nature and shearing mechanisms.

36 MATERIALS SCIENCE↗

Microstructural Development and Mechanical Properties of Friction Stir Welded Ferritic Stainless Steel AISI 409

This work investigates the effect of friction stir welding process parameters (rotation rate and traverse speed) on the microstructural evolution of friction stir welded (FSWed) ferritic stainless steel (FSS) AISI 409. Optical microscope, scanning electron microscope and electron backscattering diffraction are used to quantitatively assess the development in grain structure and texture. The microstructural development suggested that thermo-mechanical deformation occurs in the stir zone within the austenite/ferrite phase region, ultimately transforming upon cooling into bainitic/ferritic microstructure. The fraction and size of the bainitic/ferritic grains are found to vary through the thickness of the joints. High fractions of coarse ferritic grains are found near the top of the stir zone, and low fraction of fine ferritic grains is found near the bottom of the stir zone. This bainitic/ferritic grain structure resulted in an increase in the hardness of the stir zone by about 74% relative to the base material. The tensile strength of the FSWed FSS joints is almost at the same level of the base material with reduction in the ductility as a result of the increased hardness of the weld zone.

36 MATERIALS SCIENCE↗

In-Plane Liftout and Push-to-Pull for In Situ Mechanical Testing of Irradiated Inconel X-750

A streamlined sample preparation method for nanomechanical testing is needed to improve the quality of specimens, reduce the cost, and increase the versatility of specimen fabrication. This work outlines an in-plane liftout focused ion beam (FIB) fabrication procedure to prepare electron-transparent specimens for in situ transmission electron microscopy (TEM) nanomechanical testing. Ion etching and electron backscatter diffraction (EBSD) techniques were used to lift out a [110] oriented grain from a neutron-irradiated bulk X-750 alloy. Careful control of voltages and currents ensured precision. Top surface thinning sweeps prevented resurfacing and redeposition while dog-bone geometries were shaped with a 1:4 gauge width-to-milling pattern diameter ratio. Nanotensile testing in the TEM with a picoindenter allowed for the estimation of an ultimate tensile strength of 2.41 GPa, and inspection revealed a high density of bubbles in the X-750 matrix. The proposed fabrication procedure is significant for preparing samples from radioactive materials, studying complex structures that are orientation-dependent, and analyzing desired planar areas.

36 MATERIALS SCIENCE↗

Microstructure and Properties of Inconel 718 Fabricated by Directed Energy Deposition with In-Situ Ultrasonic Impact Peening

Many inherent issues, such as the detrimental residual stress, columnar grains with anisotropy, and weak mechanical properties, have severely impeded the adoption of metal additive manufacturing (AM) techniques including powder bed fusion and directed energy deposition (DED) processes. In this study, a hybrid AM process that consists of layer-wise laser metal deposition (i.e., a DED process) and in-situ ultrasonic impact peening (UIP) was applied to obtain Inconel 718 superalloy workpieces. Also, for further property enhancement, a post-heat treatment was applied to the deposited material obtained by the hybrid AM process. Scanning electron microscopy and transmission electron microscope were used to investigate the microstructure morphology and reveal the underlying strengthening mechanism. Electron backscatter diffraction was employed to quantitatively study the microstructure resulted from the hybrid AM process and the post-heat treatment. The profile of residual stress along the depth direction was obtained through X-ray diffraction. The results demonstrate that this hybrid AM process is capable of producing high-quality metal parts with significantly refined microstructure, and beneficial compressive residual stress along the depth into surface. Severe plastic strains are introduced by UIP, and the resulted mechanical twinning and dynamic recrystallization play an important role in refining microstructure. The material microstructure is further refined down to 100 µm, and the texture anisotropy is significantly diminished after solution treatment at 980 °C for 1 hour. Under the as-built condition, in-situ ultrasonic peening alters the residual stress component from a tensile state to an overall compressive state with a maximum value of − 190 MPa within the range of measurement depth.

36 MATERIALS SCIENCE↗

The formation mechanisms of interlocked microstructures in low-carbon high-strength steel weld metals

Microstructural features and the formation mechanisms of interlocked microstructures of acicular ferrite in a low-carbon high-strength steel weld metal were investigated by means of computer-aided three-dimensional reconstruction technique and electron backscattered diffraction analysis. Multiple nucleation on inclusions, sympathetic nucleation or repeated nucleation, hard impingement, mutual intersection, and fixed orientation relationships of acicular ferrite grains were observed. They were all responsible for the formation of interlocked microstructures in the weld metal. During the process of isothermal transformation, the pre-formed acicular ferrite laths or plates partitioned austenite grains into many small and separate regions, and the growth of later formed acicular ferrite grains was confined in these small regions. Thus, the crystallographic grain size became smaller with the increasing holding time. Highlights: Black-Right-Pointing-Pointer Acicular ferrite is formed by multiple nucleation and sympathetic nucleation. Black-Right-Pointing-Pointer Hard impingement and intersection of ferrite grains occur at later stages. Black-Right-Pointing-Pointer The pre-formed ferrite laths partition austenite grains into smaller regions. Black-Right-Pointing-Pointer The growth of later formed ferrite grains is confined in the smaller regions.

36 MATERIALS SCIENCE↗

Structural characterization of “carbide-free” bainite in a Fe–0.2C–1.5Si–2.5Mn steel

Low-alloyed, low C containing carbide-free bainitic steels are attractive candidates for applications in the automotive industry due to their well-balanced combination of high strength and ductility achieved in an economic way. In this work, their complex microstructure consisting of a mixture of bainitic ferrite, austenite with different morphologies and stabilities, martensite, M/A constituent and a few carbides has been investigated with metallographic and high-resolution techniques. After specific isothermal heat treatments in a dilatometer, a combination of LePera and Nital etching was applied to distinguish between bainite and martensite. Site-specific atom probe tips were prepared by means of scanning electron microscopy, electron backscatter diffraction and focused ion beam, revealing that “carbide-free” bainite consists of C depleted bainitic ferrite, C enriched retained austenite and occasional ε-carbides. Furthermore, it was found that the M/A constituent is highly dislocated and mainly martensitic. Its C content is increased compared to the nominal composition, but below the values obtained for retained austenite, explaining the lower transformation resistance. - Highlights: • Detailed top-down characterization of low C “carbide-free” bainitic steel • APT of all constituents in “carbide-free” bainite • Identification of ε-carbide based on its C content determined by APT • M/A constituent is mainly martensitic with austenitic areas at the boundaries • Lower C content of M/A constituent explains its lower stability.

36 MATERIALS SCIENCE↗

Effect of Microstructure Refinement on Hardness Homogeneity of Aluminum Alloy 1100 Processed by Accumulative Roll Bonding

This work examines the effect of grain refinement via accumulative roll bonding (ARB) on the homogeneity of microstructure and hardness through the thickness of commercially pure aluminum AA1100 sheets. The use of 7 cycles of ARB was shown to produce homogeneous ultrafine-grained microstructure, reducing the grain size to 0.46 and 1.03 µm in normal direction and rolling direction, respectively. Examination by electron backscattered diffraction indicates that continuous dynamic recrystallization was the main mechanism for the formation of submicron equiaxed grains bounded with high-angle grain boundaries (HAGBs). The fraction of HAGBs increased gradually reaching a maximum of 71.6% after 7 cycles. Through-thickness hardness measurements using Vickers and nanoindentation tests show an increase from 43.5 Hv (0.85 GPa) for as-received sample to 63 Hv (1.1 GPa) after 7 cycles. The heterogeneity in hardness through the thickness of the as-received material was shown to restrain the evolution of uniform hardness across the sheet thickness with increasing ARB cycles. Tensile tests showed that the tensile strength is increased to 250 MPa, which is about 2 times its initial value. Owing to the high stacking fault energy of AA1100, strong dynamic recovery occurred with increasing ARB strain which was balanced with the strain hardening property of the material. This resulted in plastic instability at small strains and thus early necking during the tensile test.

36 MATERIALS SCIENCE↗

Microstructural and textural evolution of AZ61 magnesium alloy sheet during bidirectional cyclic bending

In this work, the microstructural and textural evolution in the sheets of AZ61 magnesium alloy was studied by means of bidirectional cyclic bending for 8 passes at 623 K. The bended samples were examined by optical microscopy and electron backscatter diffraction analysis. The results showed that a gradient structure with fine grains about 3 μm in the regions near two surfaces and, in contrast, coarse grains in the middle of the sheet were formed. The evident grain refinement was attributed to twin-assisted dynamic recrystallization and continuous dynamic recrystallization induced by kink bands. The texture intensity was clearly reduced, resulting in a negative gradient distribution, with the texture intensity decreases from the center of the sheet to two surfaces. The weakened texture greatly facilitated the reduction of the yield strength. A higher fracture elongation and a slightly improved ultimate tensile strength were achieved concurrently. - Highlights: • The AZ61 Mg alloy is deformed at 623 K by bidirectional cyclic bending. • A symmetric gradient distribution of fine grains along the thickness is formed. • The basal texture in the regions near two surfaces is weakened significantly.

36 MATERIALS SCIENCE↗