Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometric”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Stress near geometrically complex strike-slip faults - Application to the San Andreas fault at Cajon Pass, southern California

A model is presented to rationalize the state of stress near a geometrically complex major strike-slip fault. Slip on such a fault creates residual stresses that, with the occurrence of several slip events, can dominate the stress field near the fault. The model is applied to the San Andreas fault near Cajon Pass. The results are consistent with the geological features, seismicity, the existence of left-lateral stress on the Cleghorn fault, and the in situ stress orientation in the scientific well, found to be sinistral when resolved on a plane parallel to the San Andreas fault. It is suggested that the creation of residual stresses caused by slip on a wiggle San Andreas fault is the dominating process there.

Saucier, Francois↗
NASA NTRS1992

Thermally-induced, geometrically nonlinear response of symmetrically laminated composite plates

This paper discusses the thermally-induced geometrically nonlinear response of symmetrically laminated composite plates. The plate response is due to a temperature increase that is uniform in the plane of the plate but has a slight gradient through the thickness. The case of a completely uniform temperature increase but with an initial out-of-plane imperfection in the plate is also considered. Because they are closely allied problems, thermal buckling and postbuckling are discussed. Using variational methods in conjunction with a Rayleigh-Ritz formulation, these responses are investigated for two laminates, a (+/- 45/0/90)s and a (+/- 45/02)s, under two different simple support conditions.

Meyers, C. A.↗
NASA NTRS1992

A curvilinear, anisotropic, p-version, brick finite element based on geometric entities

A 'brick' solid finite element is presently developed on the basis of the p-version analysis, and used to demonstrate the FEM concept of 'geometric entities'. This method eliminates interelement discontinuities between low- and high-order elements, allowing very fine control over the shape-function order in various parts of the model. Attention is given to the illustrative cases of a one-element model of an elliptic pipe, and a square cross-section cantilevered beam.

Hinnant, Howard E.↗
NASA NTRS1992

Geometric-optical bidirectional reflectance modeling of the discrete crown vegetation canopy - Effect of crown shape and mutual shadowing

Many natural vegetation covers can be regarded as assemblages of plant crowns, on a background, which interact with light as discrete objects. On this basis, geometric optics furnish an approach to the modeling of vegetation canopies that captures the most important features of such growths' bidirectional measurements. Attention is presently given to models which approximate these phenomena and relate the size, shape, and count density of plant crowns to viewing and illumination positions and to crown-background reflectance contrasts.

Li, Xiaowen↗
NASA NTRS1992

Geometrically thin, hot accretion disks - Topology of the thermal equilibrium curves

All the possible thermal equilibrium states of geometrically thin alpha-disks around stellar-mass black holes are presented. A (vertically) one-zone disk model is employed and it is assumed that a main energy source is viscous heating of protons and that cooling is due to bremsstrahlung and Compton scattering. There exist various branches of the thermal equilibrium solution, depending on whether disks are effectively optically thick or thin, radiation pressure-dominated or gas pressure-dominated, composed of one-temperature plasmas or of two-temperature plasmas, and with high concentration of e(+)e(-) pairs or without pairs. The thermal equilibrium curves at high temperatures (greater than or approximately equal to 10 exp 8 K) are substantially modified by the presence of e(+)e(-) pairs. The thermal stability of these branches are examined.

Kusunose, Masaaki↗
NASA NTRS1992

Geometric modeling of inflatable structures for lunar base

A modular inflatable structure consisting of thin, composite membranes is presented for use in a lunar base. Results from a linear elastic analysis of the structure indicate that it is feasible in the lunar environment. Further analysis requires solving nonlinear equations and accurately specifying the geometries of the structural members. A computerized geometric modeling technique, using bicubic Bezier surfaces to generate the geometries of the inflatable structure, was conducted. Simulated results are used to create three-dimensional wire frames and solid renderings of the individual components of the inflatable structure. The component geometries are connected into modules, which are then assembled based upon the desired architecture of the structure.

Nowak, Paul S.↗
NASA NTRS1992

Parallel algorithms for geometric connected component labeling on a hypercube multiprocessor

Different algorithms for the geometric connected component labeling (GCCL) problem are defined each of which involves d stages of message passing, for a d-dimensional hypercube. The major idea is that in each stage a hypercube multiprocessor increases its knowledge of domain. The algorithms under consideration include the QUAD algorithm for small number of processors and the Overlap Quad algorithm for large number of processors, subject to the locality of the connected sets. These algorithms differ in their run time, memory requirements, and message complexity. They were implemented on an Intel iPSC2/D4/MX hypercube.

Belkhale, K. P.↗
NASA NTRS1992

Extracting dimensional geometric parameters from B-spline surface models of aircraft

Research that creates techniques to automatically obtain dimensional geometric parameters from the nonuniform B-spline surface description of an object is presented. These techniques have been implemented successfully in the aircraft design software, ACSYNT, a computer-aided design system for conceptual aircraft design created at Virginia Tech and NASA Ames. The techniques created and implemented in this research are also of significance to general-purpose design.

Jayaram, U.↗
NASA NTRS1991

A geometrically nonlinear analysis of interlaminar stresses in unsymmetrically laminated plates subjected to uniform thermal loading

An analytical study of interlaminar stresses in unsymmetrically laminated plates is presented. The study examines the linear elastic, large deflection response of square laminated composite plates subjected to uniform thermal loading. Both cross-ply and angle-ply, symmetric and unsymmetric, laminates are examined to evaluate the effects of mismatch between adjacent layers in elastic constants and coefficients of thermal expansion. A geometrically nonlinear kinematic description is used to predict the large out-of-plane (transverse) deflections. The nonlinear, three-dimensional boundary value problems are formulated from elasticity theory and approximate solutions are determined using the finite element method. A global/local analysis procedure is used to obtain improved free edge stress predictions. For the laminates and loading conditions considered, the results indicate that the out-of-plane deflections of the unsymmetric laminates reduce interlaminar shear stresses. These deflections also reduce interlaminar normal stresses in some laminates and increase these stresses for others. The results indicate that as the out-of-plane deflections become large, the differences in interlaminar stress predictions between linear and nonlinear theory can become quite large.

Norwood, D. S.↗
NASA NTRS1993

Geometrically nonlinear analysis of stiffened composite panels with various end-support conditions

Recent enhancements to the NLPAN computer code are presented. NLPAN is a finite strip method for the geometrically nonlinear static analysis of prismatic composite structures subjected to in-plane and pressure loading. Refinements to the original approach of NLPAN are noted, and the modifications necessary to model clamped ends, eccentrically loaded ends, and ends with rotationally elastic support are discussed. Analytical predictions for axially loaded stiffened panels with various types of end support are compared with experimental measurements. Overall there is good agreement between analytical results and test results. The method is successful in modelling key mechanisms which can cause elastic collapse.

Stoll, Frederick↗
NASA NTRS1993

An initial comparison of CFD with experiment for a geometrically simplified STOVL model

The transition flight performance of a representative Short Take-Off or Vertical Landing (STOVL) model is investigated using side-by-side experimental and numerical simulations. The model consists of a 60 deg cropped delta wing planform; a simple fuselage shape blended to the wing; and tandem, circular, high-pressure-air lift jets that exit perpendicular to the flat lower surface. The configuration was chosen to minimize the geometric modeling complexity while retaining the important flow physics of the lift-jet/aerodynamic surface interaction. Three-dimensional, turbulent Navier-Stokes computations are made using a multiple, overset grid scheme. Results are presented and compared with the measured forces and pressures for the model at a freestream Mach number of 0.14 and a 10 deg angle-of-attack without lift jets operating. Computed surface flow patterns and particle traces show that the simulation predicts primary and secondary wing leading edge vortices for these conditions.

Roth, Karlin R.↗
NASA NTRS1957

Nonlifting wing-body combinations with certain geometric restraints having minimum wave drag at low supersonic speeds

Several variational problems involving optimum wing and body combinations having minimum wave drag for different kinds of geometrical restraints are analyzed. Particular attention is paid to the effect on the wave drag of shortening the fuselage and, for slender axially symmetric bodies, the effect of fixing the fuselage diameter at several points or even of fixing whole portions of its shape.

Lomax, Harvard↗
NASA NTRS1941

Heat transfer in geometrically similar cylinders

The power and heat-stress conditions of geometrically similar engines are discussed. The advantages accruing from smaller cylinder dimensions are higher specific horsepower, lower weight per horsepower, lower piston temperature, and less frontal area, with reduced detonation tendency.

Riekert, P↗
NASA NTRS1993

Geometric stiffening in multibody dynamics formulations

In this paper we discuss the issue of geometric stiffening as it arises in the context of multibody dynamics. This topic has been treated in a number of previous publications in this journal and appears to be a debated subject. The controversy revolves primarily around the 'correct' methodology for incorporating the stiffening effect into dynamics formulations. The main goal of this work is to present the different approaches that have been developed for this problem through an in-depth review of several publications dealing with this subject. This is done with the goal of contributing to a precise understanding of the existing methodologies for modelling the stiffening effects in multibody systems. Thus, in presenting the material we attempt to illuminate the key characteristics of the various methods as well as show how they relate to each other. In addition, we offer a number of novel insights and clarifying interpretations of these schemes. The paper is completed with a general classification and comparison of the different approaches.

Sharf, Inna↗
NASA NTRS1993

Improvements to a method for the geometrically nonlinear analysis of compressively loaded stiffened composite panels

The NLPAN computer code uses a finite-strip approach to the analysis of thin-walled prismatic composite structures such as stiffened panels. The code can model in-plane axial loading, transverse pressure loading, and constant through-the-thickness thermal loading, and can account for shape imperfections. The NLPAN code represents an attempt to extend the buckling analysis of the VIPASA computer code into the geometrically nonlinear regime. Buckling mode shapes generated using VIPASA are used in NLPAN as global functions for representing displacements in the nonlinear regime. While the NLPAN analysis is approximate in nature, it is computationally economical in comparison with finite-element analysis, and is thus suitable for use in preliminary design and design optimization. A comprehensive description of the theoretical approach of NLPAN is provided. A discussion of some operational considerations for the NLPAN code is included. NLPAN is applied to several test problems in order to demonstrate new program capabilities, and to assess the accuracy of the code in modeling various types of loading and response. User instructions for the NLPAN computer program are provided, including a detailed description of the input requirements and example input files for two stiffened-panel configurations.

Stoll, Frederick↗
NASA NTRS1993

Transitional flight characteristics of a geometrically simplified STOVL model

The transitional flight characteristics of a geometrically simplified Short Take-Off Vertical Landing (STOVL) aircraft configuration were measured in the NASA Ames 7- by 10-Foot Wind Tunnel. The experiment was designed to provide detailed data for evaluating the capability of computational fluid dynamics methods to predict the important powered lift flow parameters. The model consists of a 60 deg cropped delta wing planform; a blended fuselage; and tandem, circular, high pressure air jets that exit perpendicular to the flat lower surface. Freestream Mach number is limited to a maximum 0.2. Model angle of attack ranges from -10 deg to +20 deg. The nozzle pressure ratios of both jets are varied between 1 and 3, and the jet exit temperatures are maintained at near ambient conditions. Detailed surface pressure measurements show that suction pressure peaks located on the upper surface of the wing during conventional wingborne flight for angles of attack greater than 5 deg move to the wing lower surface at angles of attack less than 0 deg. A reduction in these suction pressure peaks is observed when the lift jets are operating. With sonic jet exit conditions, a freestream Mach number of 0.14, and 0 deg angle of attack, the jet-induced suckdown is equivalent to a 3.7 deg reduction in angle of attack. Schlieren, laser light sheet flow visualization and total pressure measurements in the jet plumes provide a description of the three-dimensional jet efflux flowfield.

Roth, Karlin R.↗
NASA NTRS1994

A geometric model of a V-slit Sun sensor correcting for spacecraft wobble

A V-Slit sun sensor is body-mounted on a spin-stabilized spacecraft. During injection from a parking or transfer orbit to some final orbit, the spacecraft may not be dynamically balanced. This may result in wobble about the spacecraft spin axis as the spin axis may not be aligned with the spacecraft's axis of symmetry. While the widely used models in Spacecraft Attitude Determination and Control, edited by Wertz, correct for separation, elevation, and azimuthal mounting biases, spacecraft wobble is not taken into consideration. A geometric approach is used to develop a method for measurement of the sun angle which corrects for the magnitude and phase of spacecraft wobble. The algorithm was implemented using a set of standard mathematical routines for spherical geometry on a unit sphere.

Mcmartin, W. P.↗
NASA NTRS1993

Geometric moire methods with enhanced sensitivity by optical/digital fringe multiplication

A robust fringe-shifting and image processing scheme is applied to geometric moire experiments. High quality contour maps of U, V and W displacement fields are obtained with sensitivity enhanced by a factor of ten. The method is compatible with complicated intensity distributions, variable bar-to-space ratios of gratings, and optical noise. It is applicable to large fields for both in-plane moire and shadow moire measurements.

Han, B.↗