Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Discontinuously reinforced intermetallic matrix composites via XD synthesis

A review is given of recent results obtained for discontinuously reinforced intermetallic matrix composites produced using the XD process. Intermetallic matrices investigated include NiAl, multiphase NiAl + Ni2AlTi, CoAl, near-gamma titanium aluminides, and Ll2 trialuminides containing minor amounts of second phase. Such mechanical properties as low and high temperature strength, compressive and tensile creep, elastic modulus, ambient ductility, and fracture toughness are discussed as functions of reinforcement size, shape, and volume fraction. Microstructures before and after deformation are examined and correlated with measured properties. An observation of interest in many of the systems examined is 'dispersion weakening' at high temperatures and high strain rates. This behavior is not specific to the XD process; rather similar observations have been reported in other discontinuous composites. Proposed mechanisms for this behavior are presented.

Kumar, K. S.↗

Cyclic nanoindentation studies on CrN thin films prepared by RF sputtering on Zr-based metallic glass

Cyclic nanoindentation tests were carried out to study the influence of the chromium nitride thin films on the mechanical properties of Zr-based metallic glass. Chromium nitride thin coatings have been deposited on Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate by RF sputtering. The deposition process was done at room temperature under nitrogen reactive gas using a metallic chromium target. The CrN films have a thickness of 300 nm. Several cyclic nanoindentation measurements were conducted on CrN films and Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate samples at various loading rate values. We have found that the coated metallic glass sample shows high mechanical properties such as hardness and reduced elastic modulus. Cyclic nanoindentation results show a hardening behaviour for these CrN coatings. Moreover, the CrN coated on Zr-based metallic glass was found to have a high value of resistance to crack propagation, as being analysed through the SEM pictures of the residual Vickers indentation impressions.

36 MATERIALS SCIENCE↗

Shear Strength Measurements on Adhesive-Bonded High Explosive Joints (Progress Summary)

The testing of block shear joints to determine ultimate shear strength and modulus is described by the ASTM D905 standard. However, ASTM D905 is not directly applicable for High Explosive (HE) joints, as it requires large masses of HE and the mechanical testing fixture may damage the HE. We have developed capabilities at LLNL to measure the shear strength of adhesive-bonded HE joints.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High pressure synthesis of amorphous TiO{sub 2} nanotubes

Amorphous TiO{sub 2} nanotubes with diameters of 8-10 nm and length of several nanometers were synthesized by high pressure treatment of anatase TiO{sub 2} nanotubes. The structural phase transitions of anatase TiO{sub 2} nanotubes were investigated by using in-situ high-pressure synchrotron X-ray diffraction (XRD) method. The starting anatase structure is stable up to ∼20GPa, and transforms into a high-density amorphous (HDA) form at higher pressure. Pressure-modified high- to low-density transition was observed in the amorphous form upon decompression. The pressure-induced amorphization and polyamorphism are in good agreement with the previous results in ultrafine TiO{sub 2} nanoparticles and nanoribbons. The relationship between the LDA form and α-PbO{sub 2} phase was revealed by high-resolution transmission electron microscopy (HRTEM) study. In addition, the bulk modulus (B{sub 0} = 158 GPa) of the anatase TiO{sub 2} nanotubes is smaller than those of the corresponding bulks and nanoparticles (180-240 GPa). We suggest that the unique open-ended nanotube morphology and nanosize play important roles in the high pressure phase transition of TiO{sub 2} nanotubes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A phononic crystal strip based on silicon for support tether applications in silicon-based MEMS resonators and effects of temperature and dopant on its band gap characteristics

Phononic crystals (PnCs) and n-type doped silicon technique have been widely employed in silicon-based MEMS resonators to obtain high quality factor (Q) as well as temperature-induced frequency stability. For the PnCs, their band gaps play an important role in the acoustic wave propagation. Also, the temperature and dopant doped into silicon can cause the change in its material properties such as elastic constants, Young’s modulus. Therefore, in order to design the simultaneous high Q and frequency stability silicon-based MEMS resonators by two these techniques, a careful design should study effects of temperature and dopant on the band gap characteristics to examine the acoustic wave propagation in the PnC. Based on these, this paper presents (1) a proposed silicon-based PnC strip structure for support tether applications in low frequency silicon-based MEMS resonators, (2) influences of temperature and dopant on band gap characteristics of the PnC strips. The simulation results show that the largest band gap can achieve up to 33.56 at 57.59 MHz and increase 1280.13 % (also increase 131.89 % for ratio of the widest gaps) compared with the counterpart without hole. The band gap properties of the PnC strips is insignificantly effected by temperature and electron doping concentration. Also, the quality factor of two designed length extensional mode MEMS resonators with proposed PnC strip based support tethers is up to 1084.59% and 43846.36% over the same resonators with PnC strip without hole and circled corners, respectively. This theoretical study uses the finite element analysis in COMSOL Multiphysics and MATLAB softwares as simulation tools. This findings provides a background in combination of PnC and dopant techniques for high performance silicon-based MEMS resonators as well as PnC-based MEMS devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pultrusion and Vitrimer Composites: Emerging Pathways for Sustainable Structural Materials

Pultrusion is a manufacturing process used to produce fiber-reinforced polymer composites with excellent mechanical, thermal, and chemical properties. The resulting materials are lightweight, durable, and corrosion-resistant, making them valuable in aerospace, automotive, construction, and energy sectors. However, conventional thermoset composites remain difficult to recycle due to their infusible and insoluble cross-linked structure. This review explores integrating vitrimer technology a novel class of recyclable thermosets with dynamic covalent adaptive networks into the pultrusion process. As only limited studies have directly reported vitrimer pultrusion to date, this review provides a forward-looking perspective, highlighting fundamental principles, challenges, and opportunities that can guide future development of recyclable high-performance composites. Vitrimers combine the mechanical strength (tensile strength and modulus) of thermosets with the reprocessability and reshaping of thermoplastics through dynamic bond exchange mechanisms. These polymers offer high-temperature reprocessability, self-healing, and closed-loop recyclability, where recycling efficiency can be evaluated by the recovery yield retention of mechanical properties and reuse cycles meeting the demand for sustainable manufacturing. Key aspects discussed include resin formulation, fiber impregnation, curing cycles, and die design for vitrimer systems. The temperature-dependent bond exchange reactions present challenges in achieving optimal curing and strong fiber–matrix adhesion. Recent studies indicate that vitrimer-based composites can maintain structural integrity while enabling recycling and repair, with mechanical performance such as flexural and tensile strength comparable to conventional composites. Incorporating vitrimer materials into pultrusion could enable high-performance, lightweight products for a circular economy. The remaining challenges include optimizing curing kinetics, improving interfacial adhesion, and scaling production for widespread industrial adoption.

Fiber composites↗

Unveiling Carbon Ring Structure Formation Mechanisms in Polyacrylonitrile-Derived Carbon Fibers

As the demand for electric vehicles (EVs) and autonomous vehicles (AVs) rapidly grows, lower-cost, lighter, and stronger carbon fibers (CFs) are urgently needed to respond to consumers’ call for greater EV traveling range and stronger safety structures for AVs. Converting polymeric precursors to CFs requires a complex set of thermochemical processes; a systematic understanding of each parameter in fiber conversion is still, to a large extent, lacking. Here, we demonstrate the effect of carbonization temperature on carbon ring structure formation by combining atomistic/microscale simulations and experimental validation. Experimental testing, as predicted by simulations, exhibited that the strength and ductility of PAN CFs decreased, whereas the Young’s modulus increased with increasing carbonization temperature. Our simulations unveiled that high carbonization temperature accelerated the kinetics of graphitic phase nucleation and growth, leading to the decrease in strength and ductility but increase in modulus. The methodology presented herein using combined atomistic/microscale simulations and experimental validation lays a firm foundation for further innovation in CF manufacturing and low-cost alternative precursor development.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of bulk highly faulted fcc/hcp nanostructured cobalt microstructures

Nanostructured cobalt powders with an average particle size of 50 nm were synthesized using a polyol method and subsequently consolidated by spark plasma sintering (SPS). SPS experiments performed at 650 °C with sintering times ranging from 5 to 45 min under a pressure of 100 MPa, yielded to dense bulk nanostructured cobalt (relative density greater than 97%). X-ray diffraction patterns of the as-prepared powders showed only a face centered cubic (fcc) crystalline phase, whereas the consolidated samples exhibited a mixture of both fcc and hexagonal close packed (hcp) phases. Transmission electron microscopy observations revealed a lamellar substructure with a high density of nanotwins and stacking faults in every grain of the sintered samples. Room temperature compression tests, carried out at a strain rate of 10{sup −3} s{sup −1}, yielded to highest strain to fracture values of up to 5% for sample of holding time of 15 min, which exhibited a yield strength of 1440 MPa, an ultimate strength as high as 1740 MPa and a Young's modulus of 205 GPa. The modulus of elasticity obtained from the nanoindentation tests, ranges from 181 to 218 GPa. The lowest modulus value of 181 GPa was obtained for the sample with the highest sintering time (45 min), which could be related to mass density loss as a consequence of trapped gases releasing. - Highlights: • Co nanopowder (50 nm) was prepared by reduction in polyol medium. • SPS was used to process bulk nanostructured Co specimens. • Microstructures were made of intricate fcc/hcp, along with nanotwins and SFs. • High strengths and moderate compressive ductility were obtained. • Deformation mechanisms related to complex interplay of different length scales.

36 MATERIALS SCIENCE↗

Thermal, Rheological, Mechanical and Morphological Behavior of High Density Polyethylene and Carboxymethyl Cellulose Blend

In this study water soluble sodium carboxymethyl cellulose (CMC) was blended with high density polyethylene (HDPE) by peroxide-initiated melt compounding technique. The compatibility of the blended polymers were carried out by silane crosslinking agent. A series of blends were prepared by varying the CMC contents up to a maximum of 50 phr. The physical properties of non-crosslinked and crosslinked blends were investigated in detail. FTIR analysis of crosslinked blend confirmed the presence of Si–O–Si and Si–O–C absorption peaks at 1050 and 1159 cm{sup −1}. Thermal stability of crosslinked blends improved as compared to its non-crosslinked congener. Rheological study of crosslinked blends illustrated high complex viscosity and dynamic shear storage modulus. The tensile strength of virgin polyethylene was 8.1 MPa whereas the maximum tensile strength of 19.6 MPa was observed in crosslinked blend. Similarly lower deformation was observed in crosslinked blends under static load. Scanning electron microscopy of crosslinked formulations also showed strong adhesion between the polymers interface. The compatibility of HDPE and CMC is attributed to both free radical and condensation reactions.

36 MATERIALS SCIENCE↗

Thermal, Mechanical Properties and Rheological Behavior of Poly(Propylene Carbonate)/Poly(Ethylene Glycol)/Graphene Oxide Nanocomposites

Graphene oxide (GO) is an efficient nanofiller for polymers and a good dispersion of GO in polymer matrix is most important to enhance properties. Poly(propylene carbonate) (PPC)/GO nanocomposite was prepared by a method with solution blending and melt mixing for improvement of GO dispersion. First, GO was prepared using an improved Hummers method. In the solution blending, GO was well dispersed in water and another low molecular weight polymer, poly(ethylene glycol) (PEG), was also dispersed in water, as a dispersion medium for next melt mixing of PPC and GO. Then PPC and PEG/GO was melt-mixed in a HAAKE mixer. The dispersion of GO in PPC matrix and effect of GO content on properties of PPC/PEG/GO nanocomposites was investigated. Results show that tensile strength of nanocomposites with the content of 0.5 wt% GO increased from 17.51 MPa (pure PPC) to 21.61 MPa and elongation at break can be kept high. The complex viscosity, storage and loss modulus is the highest for nanocomposites with the content of 0.5 wt% GO. This illustrated that a lower content of GO can improve the properties of PPC, owing to the good dispersion of GO in PPC matrix. Based on dispersion of GO and chemical structure of PPC, PEG, and GO, the reinforcement mechanism of GO in PPC was analyzed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Graphene nanoplatelets reinforced cement as a solution to leaky wellbores reinforcing weak points in hydrated Portland cement with graphene nanoparticles improves mechanical and chemical durability of wellbore cements

In this work, to improve the performance of wellbore cement under subsurface environments, graphene nanoplatelets (GNPs) were added in various percentages to Class-H cement slurry. Microstructural characterization of cement slurries cured at 90 °C and 95% RH indicates that GNP modifies the microstructure of hydrated cement by reinforcing pore spaces. As a result, the mechanical properties, such as Young's modulus and axial peak stress, obtained from high temperature triaxial compression tests are significantly improved based on different percentages of added GNPs. Furthermore, the hydrated 1 × 2 inch GNP- Portland cement cores tested under simulated deep wellbore conditions of high-temperature and high pressure (HTHP), appear to have a ductile-like behavior, when compared to a typical brittle nature of Portland cement pastes. From our observations and published data on graphene resistance to fracture, GNP addition to cement is evidently enhancing the flexibility of cement. These improvements would reduce the risks associated with wellbore cement deterioration and a consequent leakage in fossil fuel production, geothermal energy production, CO 2 storage as well as long-term sealing materials in plugging and abandonment of all wellbores at the end of their service life.

36 MATERIALS SCIENCE↗

Polyester-based epoxy vitrimer integrating spent coffee ground as a natural filler

Coffee is a widely consumed beverage, but approximately 80% mass of coffee cherry is discarded as waste. Here, in this study, spent coffee grounds (SCG) were recycled and used as a natural filler in a polyester-based epoxy matrix made from reactions of diglycidyl ethers of Bisphenol A and polyethylene glycol with methyl nadic anhydride. The properties of SCG/epoxy composites with various SCG contents up to 40% w/w were evaluated using various techniques such as FT-IR spectroscopy, tensile testing, optical microscopy, differential scanning calorimetry, and rheology. The SCG filled polyester-based epoxy matrix demonstrated excellent dimensional stability and retained a permanently crosslinked network, but re-shaping was possible at ~150 °C through transesterification, which occurred due to a dynamic chain exchange reaction between the ester group of the epoxy matrix and the hydroxyl group of the SCG fillers. The transesterification also improved the interfacial adhesion between the matrix and SCG fillers, resulting in tensile strength of over 20 MPa and a modulus of around 2.5 GPa, even with high SCG contents up to 40% w/w. While neat, cured epoxy shows thermoset behavior, filling the matrix with SCG enables reforming and origami-inspired spontaneous change in shape.

42 ENGINEERING↗

Effects of Sn addition on the microstructure, mechanical properties and corrosion behavior of Ti–Nb–Sn alloys

Ti and Ti alloys are widely used in restorative surgery because of their good biocompatibility, enhanced mechanical behavior and high corrosion resistance in physiological media. The corrosion resistance of Ti-based materials is due to the spontaneous formation of the TiO{sub 2} oxide film on their surface, which exhibits elevated stability in biological fluids. Ti–Nb alloys, depending on the composition and the processing routes to which the alloys are subjected, have high mechanical strength combined with low elastic modulus. The addition of Sn to Ti–Nb alloys allows the phase transformations to be controlled, particularly the precipitation of ω phase. The aim of this study is to discuss the microstructure, mechanical properties and corrosion behavior of cast Ti–Nb alloys to which Sn has been added. Samples were centrifugally cast in a copper mold, and the microstructure was characterized using optical microscopy, scanning electron microscopy and X-ray diffractometry. Mechanical behavior evaluation was performed using Berkovich nanoindentation, Vickers hardness and compression tests. The corrosion behavior was evaluated in Ringer's solution at room temperature using electrochemical techniques. The results obtained suggested that the physical, mechanical and chemical behaviors of the Ti–Nb–Sn alloys are directly dependent on the Sn content. - Graphical abstract: Effects of Sn addition to the Ti–30Nb alloy on the elastic modulus. - Highlights: • Sn addition causes reduction of the ω phase precipitation. • Minimum Vickers hardness and elastic modulus occurred for 6 wt.% Sn content. • Addition of 6 wt.% Sn resulted in maximum ductility and minimum compression strength. • All Ti–30Nb–XSn (X = 0, 2, 4, 6, 8 and 10%) alloys are passive in Ringer's solution. • Highest corrosion resistance was observed for 6 wt.% Sn content.

36 MATERIALS SCIENCE↗

Investigating dry room compatibility of sulfide solid-state electrolytes for scalable manufacturing

All-solid-state batteries (ASSBs) are viewed as promising next-generation energy storage devices, due to their enhanced safety by replacing organic liquid electrolytes with non-flammable solid-state electrolytes (SSEs). The high ionic conductivity and low Young's modulus of sulfide SSEs make them suitable candidates for commercial ASSBs. Nevertheless, sulfide SSEs are generally reported to be unstable in ambient air. Moreover, instead of gloveboxes used for laboratory scale studies, large scale production of batteries is usually conducted in dry rooms. Thus, this study aims to elucidate the chemical evolution of a sulfide electrolyte, Li 6 PS 5 Cl (LPSCl), during air exposure and to evaluate its dry room compatibility. When LPSCl is exposed to ambient air, hydrolysis, hydration, and carbonate formation can occur. Moreover, hydrolysis can lead to irreversible sulfur loss and therefore LPSCl cannot be fully recovered in the subsequent heat treatment. During heat treatment, exposed LPSCl undergoes dehydration, decomposition of carbonate species, and reformation of the LPSCl phase. Lastly, LPSCl was found to exhibit good stability in a dry room environment and was subject to only minor conductivity loss due to carbonate formation. The dry room exposed LPSCl sample was tested in a LiNi 0.8 Co 0.1 Mn 0.1 O 2 |LiIn half-cell, exhibiting no significant loss of electrochemical performance compared with the pristine LPSCl, proving it to be compatible with dry room manufacturing processes.

36 MATERIALS SCIENCE↗

An Investigation of Nanoindentation as Quality Control [Slides]

Nanoindentation Continuous Stiffness Measurement (CSM) mapping, and Strain Rate Jump Testing (SRJT) proved effective to highlight and visualize the extent of property differences between the samples. From the analysis, Lot A has a significant dead zone at its center, especially when compared with the cross section of Lot B. Quick identification of property issues from one of the two feed stocks, both of which fit the specification. Mechanical performance was connected to the microstructure. Thus, using the structure-property results, it is noted that the processing of Lot A may have been insufficient. Nanoindentation allows for the sampling of quality control variables such as hardness and modulus in a short time span at high resolution, which is cheaper and faster than traditional strength experiments (tension and compression tests).

36 MATERIALS SCIENCE↗

HTV Post Irradiation Examination (PIE) Results and Analysis

This report is responsive to 2017 Idaho National Laboratory (INL) Memorandum Purchase Order No. 00181805, statement of work 13687 “HTR Graphite R&D – FY ORNL 2017 MPO”, Deliverable 12A “issue final report on the HTV PIE to INL”, due June 15 th 2017.The HTV (High Temperature Vessel) was a HFIR (High Flux Isotope Reactor) high temperature target rod capsule in support of the DOE’s (Department of Energy) High Temperature Reactor (HTR) program. The HTV capsule contained eight sub-capsules, each with nine graphite specimens. The sub-capsules were designed to operate at ~900°C, ~1200°C or ~1600°C. The actual irradiation temperature was established by interrogating SiC and graphite TMs during PIE (post-irradiation examination. The capsule dose ranged from 1.49 dpa to 3.34 dpa, and varied with specimen position within the capsule the maximum dose occurring at the reactor mid-plane and the minimum dose occurring at the core periphery. The irradiated graphite specimens were examined during PIE to establish their high temperature dimensional and elastic (Young’s) modulus changes. The PIE results are reported and analyzed here. The dimensional and modulus changes were shown to have a strong thermal dependence. The dimensional changes were small, being of the order of a few percent or less, ranging from a maximum shrinkage of -3.1% (PCEA WG, T irr =1500°C at 3.3 dpa) to +0.131% (2114 AG, T irr = 869 at 3.2 dpa). The specimen volume shrinkages varied from –0.81 (2114, T irr = 840 at 3.1 dpa) to -9.15% (PCEA, T irr =1500°C at 3.3 dpa). The volume changes were larger at higher Irradiation temperatures. Of the six grades examined, only 2114 moved into the net positive dimensional swelling situation. Significantly, the volume change for 2114 remained negative at the doses and temperature tested here. Dimensional and volume changes were explained in terms of the temperature dependence of the crystal growth rate, the anisotropy of the crystal growth (crystallographic c-axis growth and crystallographic a-direction shrinkage) and the thermal closure of aligned micro-porosity. The modulus changes were much larger, being of the order of a few tens of percent. A trend of lesser fractional increases of Young’s Modulus with an increasing T irr was noted. The minimum increase in Young’s Modulus was 20% (H-451 WG, T irr =1500°C at 3.3 dpa) and the maximum 71% (IG-110, T irr = 840(actual) at 3.3 dpa). The rise in Young’s modulus is attributed to dislocation pinning by lattice defects produced by neutron irradiation and the temperature dependency is related to the irradiation temperature influence on the number of defect available to pin dislocations.

36 MATERIALS SCIENCE↗