Search NASA⌕ Search

SEARCH · Search NASA

Results for “material development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Emulation of neutron-irradiated microstructure of austenitic 21Cr32Ni model alloy using dual-ion irradiation

Here, in this study, the capability of heavy-ion irradiation to emulate neutron irradiation was demonstrated on an austenitic 21Cr32Ni type ternary model alloy. The model alloy used in this study is chemically analogous but compositionally simpler than of alloy 800H, which is a candidate austenitic Ni alloy which has been proposed for use in Generation IV reactors. The microstructure of the 21Cr32Ni model alloy irradiated in the BOR-60 fast reactor to 17.1 dpa and 35 dpa at ~380°C was characterized using transmission electron microscopy (TEM). The 17.1 dpa BOR-60 irradiated microstructure was then compared with the microstructure of the same material developed under dual-ion (DI) irradiation using various He/dpa ratios between 0.1 and 16.6 appm He/dpa in the temperature range of 430°C-500°C. The results showed that both neutron and DI irradiation of 21Cr32Ni model alloy produced dislocations in the form of a dislocation network as well as {111}-type faulted dislocation loops, cavities, and radiation-induced Ni enrichment at radiation-induced sinks. When the dose and the He/dpa ratio were kept similar to those in neutron irradiation, DI irradiation of the 21Cr32Ni model alloy at 460°C resulted in over-nucleation of small cavities and in a high density of faulted dislocation loops compared to those observed in the fast-neutron irradiated alloy of the same heat irradiated at ~380°C. The optimal condition for reproducing the neutron-irradiated microstructure was DI irradiation at 460°C and 0.1 appm He/dpa. In that case, the faulted loop and cavity size distributions in the BOR-60 irradiated 21Cr32Ni model alloy samples closely matched with those measured in the DI irradiated 21Cr32Ni model alloy sample. The fact that the He/dpa is an order of magnitude smaller than the helium generation rate for fast neutron irradiation, stops over nucleation and allows for the development of a similar microstructure as for neutron irradiation.

21Cr32Ni model alloy↗
DOE OSTI2025

An improved method for quantitatively measuring antifouling coating performance using a mussel single thread tensile adhesion test

Surface biofouling reduces the efficiency and lifespan of equipment across many industries. The development of high-performance antifouling surfaces, such as foul release coatings, benefits from test methods that can quickly identify superior antifouling surfaces in the laboratory during material development. Existing test methods poorly discriminate between different foul release coatings. Here is presented a method to assess the ability of surfaces to resist mussel adhesion using a quantitative, controlled single thread adhesion test (STAT) method, allowing for meaningful comparisons between low adhesion foul release surfaces. This method provides greater accuracy and finer resolution than push-based mussel shear adhesion methods without the difficulties associated with mussel size, thread attachment angle, or harming the mussels. The single thread tensile method is demonstrated on a variety of standard and high-performance coatings, and it is shown that the method detects differentiation between commercial foul release coatings that could not be resolved using other methods.

42 ENGINEERING↗
NASA NTRS2006

Experimental Results for Titan Aerobot Thermo-Mechanical Subsystem Development

This paper describes experimental results from a development program focused in maturing Titan aerobot technology in the areas of mechanical and thermal subsystems. Results from four key activities are described: first, a cryogenic balloon materials development program involving coupon and cylinder tests and culminating in the fabrication and testing of an inflated 4.6 m long prototype blimp at 93 K; second, a combined lab experiment and numerical simulation effort to assess potential problems resulting from radioisotope thermal generator waste heat generation near an inflated blimp; third, an aerial deployment and inflation development program consisting of laboratory and helicopter drop tests on a near full scale (11 m long) prototype blimp; and fourth, a proof of concept experiment demonstrating the viability of using a mechanically steerable high gain antenna on a floating blimp to perform direct to Earth telecommunications from Titan. The paper provides details on all of these successful activities and discusses their impact on the overall effort to produce mature systems technology for future Titan aerobot missions.

balloon↗
DOE OSTI2021

Effects of Hydrogen Redistribution at High Temperatures in Yttrium Hydride Moderator Material

We report advanced materials development, manufacturing, and modeling capabilities for innovative reactor designs support nuclear security and mission-focused science through enhanced technology for safer and more efficient and secure production of nuclear energy. The high temperature moderator material yttrium hydride poses a significant enhancement in small reactor design by thermalizing (slowing down) neutrons and decreasing the required fuel mass for a system. The research presented here supports understanding hydrogen distribution in yttrium hydride through: (1) the development of neutron-based hydrogen imaging and crystallographic characterization that allows us to understand fundamental diffraction behaviors and to observe changes in hydrogen distribution as a function of temperature and (2) subsequent neutron multiplication (reactivity) effects of changes in hydrogen distribution using measurement-based cross sections in a sample microreactor design. The main conclusions from the work are that: (1) hydrogen does not redistribute significantly below temperatures of 800°C in yttrium hydride and (2) hydrogen redistribution affects the reactivity slightly but not significantly.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Demonstration of Advanced Experimental and Theoretical Characterization of Hydrogen Dynamics and Associated Behavior in Advanced Reactors

Advanced materials development, manufacturing, and modeling capabilities for innovative reactor designs support nuclear security and mission-focused science through enhanced technology for safer and more efficient and secure production of nuclear energy. The research in this project has established: 1) a state-of-the-art neutron-based hydrogen mapping and cross-section measurement capability as well as detailed crystallographic characterization of hydrogen atoms at LANSCE, and 2) a multi-physics framework for simulating behavior of moderator materials and other material performance in advanced nuclear reactors. Through the course of this project, we successfully developed and demonstrated measurement techniques for hydrogen distribution and atomistic-scale behavior of hydrogen atoms using pulsed neutron techniques. In parallel, advanced multi-physics simulation tools to predict the behavior of hydrogen atoms, e.g. in a moderator for a nuclear reactor, through materials performance, neutron transport, and thermal mechanical behavior were enhanced. Multi-discipline areas across the laboratory were involved in the project as the integration of improved experimental capabilities with enhanced modeling and simulation through MST, NEN, SIGMA, and XCP division subject matter experts.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2018

Repairing large cracks and reversing fatigue damage in structural metals

Self-healing materials represent a paradigm shift from traditional materials development, enabling intrinsic repair of functionality (such as strength) after a catastrophic failure as opposed to part replacement. Several healing mechanisms have been demonstrated in polymeric and ceramic materials, but few in metallic systems. This study demonstrates a novel liquid-assisted self-healing metal-matrix composite (MMC) designed to be capable of over 90% strength recovery after a healing cycle. The aluminum (Al)-based matrix is reinforced with continuous nickel-titanium (NiTi) shape-memory alloy (SMA) reinforcements. Using a tailored heat treatment for healing, a paired effect of crack closure from the SMA reinforcement and partial liquefaction of the matrix occurs. These effects result in a compressive force across the crack surface, and, coupled with increased diffusion rates from the liquefied matrix, produces consolidation and healing in the composite structure. This work provides experimental and computational evidence for the healing mechanism under both tensile and fatigue conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

FIERRO V.X

FIERRO is a modern C++ code intended to simulate quasi-static solid mechanics problems and transient, compressible material dynamic problems with Lagrangian methods, which have meshes with constant mass elements that move with the material. FIERRO is designed to aid a) material model research that has historically been done using commercial implicit and explicit finite element codes, b) numerical methods research, and c) computer science research. FIERRO supports user developed material models that adhere to several industry standard formats by using a C++ to Fortran interface to couple the model to the numerical solvers. FIERRO is built on the ELEMENTS library that supports a diverse suite of element types, including high-order elements, and quadrature rules. The mesh class within the ELEMENTS library is designed for efficient calculations on unstructured meshes and to minimize memory usage. FIERRO is designed to readily accommodate a range of numerical methods including continuous finite element, finite volume, and discontinuous Galerkin methods. FIERRO is designed to support explicit and implicit time integration methods. FIERRO only supports a single material in an element. No physical data exists within the code.

Morgan, Nathaniel↗
NASA NTRS1978

Screening materials for smoke evolution

The density of smoke produced by burning or smoldering materials is a factor that affects the ability of occupants to escape from a burning structure and the effectiveness of firefighters. Accordingly, considerable effort is being spent on developing materials that minimize the amount of smoke without impairing their performance characteristics. In the present paper, laboratory tests on such materials are described and evaluated. It is seen that the National Bureau of Standards smoke test and the Ohio State University release-rate test are the most promising for screening materials for smoke evolution. It is shown that, for plastics, smoke obscuration is a more realistic concern than smoke toxicity.

Hilado, C. J.↗
DOE OSTI2019

Hybrid Generative Gear Manufacturing (CRADA NFE-17-06744)

Oak Ridge National Laboratory (ORNL) and Indiana Tool & Manufacturing Company, Inc. (ITAMCO) partnered to fabricate hybrid generative gears that are supposed to be 20% lighter than conventional gears without compromising strength and wear resistance. A two-pronged approach was taken to fabricate hybrid gears, the first one leveraged a design modification to deploy a mesh structure to reduce weight whereas the second approach involved fabricating the gears with a Ti64- B 4 C composites for increased wear resistance. In the first approach, the gear material was a proprietary steel alloy, Ferrium C64 ® , and the focus was to demonstrate weight reducing by leveraging additive manufacturing to deposit fine mesh structure. In the second case, the focus was on material development for gears fabricated via directed energy deposition (DED).

36 MATERIALS SCIENCE↗
NASA NTRS1985

Box truss development and its application

Since 1977, Martin Marietta Denver Aerospace has aggressively pursued development of deployable structural systems applicable to a wide variety of Shuttle-transportable large space system requirements. This effort has focused on the deployable box truss, mechanisms and materials development, mesh reflector design and fabrication, gate frame truss design and fabrication, and offset-fed antenna design and analysis. The activities discussed are: box truss design; metal matrix composites; precision joints; enhanced passive damping design; mesh reflector development; gate frame truss for solar arrays; 15-meter spinning radio meter; and 60 x 120 meter push broom antenna.

Coyner, J. V.↗
NASA NTRS2003

2002 NASA Seal/Secondary Air System Workshop

The 2002 NASA Seal/Secondary Air System Workshop covered the following topics: (i) Overview of NASA s perspective of aeronautics and space technology for the 21st century; (ii) Overview of the NASA-sponsored Ultra-Efficient Engine Technology (UEET), Turbine-Based Combined-Cycle (TBCC), and Revolutionary Turbine Accelator (RTA) programs; (iii) Overview of NASA Glenn's seal program aimed at developing advanced seals for NASA's turbomachinery, space propulsion, and reentry vehicle needs; (iv) Reviews of sealing concepts, test results, experimental facilities, and numerical predictions; and (v) Reviews of material development programs relevant to advanced seals development. The NASA UEET and TBCC/RTA program overviews illustrated for the reader the importance of advanced technologies, including seals, in meeting future turbine engine system efficiency and emission goals. For example, the NASA UEET program goals include an 8- to 15-percent reduction in fuel burn, a 15-percent reduction in CO2, a 70-percent reduction in NOx, CO, and unburned hydrocarbons, and a 30-dB noise reduction relative to program baselines. The workshop also covered several programs NASA is funding to investigate advanced reusable space vehicle technologies (X-38) and advanced space ram/scramjet propulsion systems. Seal challenges posed by these advanced systems include high-temperature operation, resiliency at the operating temperature to accommodate sidewall flexing, and durability to last many missions.

Steinetz, Bruce M.↗
NASA NTRS1992

Advanced materials for high-temperature thermoelectric energy conversion

A number of refractory semiconductors are under study at the Jet Propulsion Laboratory for application in thermal to electric energy conversion for space power. The main thrust of the program is to improve or develop materials of high figure of merit and, therefore, high conversion efficiencies over a broad temperature range. Materials currently under investigation are represented by silicon-germanium alloys, lanthanum telluride, and boron carbide. The thermoelectric properties of each of these materials, and prospects for their further improvements, are discussed. Continued progress in thermoelectric materials technology can be expected to yield reliable space power systems with double to triple the efficiency of current state of the art systems.

Vining, Cronin B.↗
DOE OSTI2019

Microstructure optimization with constrained design objectives using machine learning-based feedback-aware data-generation

Microstructure sensitive design has a critical impact on the performance of engineering materials. The safety and performance requirements of critical components, as well as the cost of material and machining of Titanium components, make dovetailing of the microstructure imperative. This paper addresses the optimization of several microstructure design problems for Titanium components under specific design constraints using a feedback-aware data-driven solution methodology. In this study, the microstructure is modeled with an orientation distribution function (ODF) that measures the volumes of different crystallographic orientations. Two algorithms are used to sample the entire microstructure space followed by machine learning-aided identification of a minimal subset of ODF dimensions which is subsequently explored by targeted sampling. Conventional optimization methods lead to a unique microstructure rather than yielding a comprehensive space of optimal or near-optimal microstructures. Multiple solutions are crucial for the deployment of materials design for manufacturing as traditional manufacturing processes can only generate a limited set of microstructures. Our data sampling-based methodology not only outperforms or is on par with other optimization techniques in terms of the optimal property value, but also provides numerous near-optimal solutions, 3–4 orders of magnitude more than previous methods. Consequently, the proposed framework delivers a spectrum of optimal solutions in the microstructure space which can accelerate materials development and reduce manufacturing costs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Material and component developments for the DEMO divertor using fibre reinforcement and additive manufacturing

Within the research along the European Fusion Roadmap, water-cooled divertor PFCs are foreseen in the design of a first fusion demonstration power plant (DEMO) in order to provide reliable heat removal capability. In the frame of this concerted attempt, the Max Planck Institute for Plasma Physics is concentrating on the development and testing of composite materials based on tungsten (W, preferred armour material) and copper (Cu, preferred heat sink material). W fibres (W f ) as monofilaments and yarns as reinforcement play a central role in these investigations due to their extraordinary properties concerning ductility already at room temperature and high tensile strength. Recent investigations on the impact of radiation damage suggest that the fibres retain their ductility upon irradiation. W reinforced with W fibres (W f /W) allows to overcome the intrinsic brittleness of W. Quantitative mechanical fracture tests of W f /W confirm the basic mechanisms of fibre reinforcement and the increased resistance to mechanical fatigue. The good wettability of W with liquid Cu and the absence of any metallurgical solubility make up an ideal material pairing for composite production. W fibre-reinforced Cu (W f /Cu) cooling tubes provide a rather high thermal conductivity (> 250 W mK -1 ) and at least twice the strength of CuCrZr in hoop direction in the temperature range up to at least 500 °C. Very recent neutron irradiation experiments confirm the sustainment of ductility of the W f /Cu composite. Numerical simulations suggest that thermal stresses in W-Cu PFCs could be strongly reduced by tailoring the local W and Cu volume fraction. This 'freely' distributed material composition can be achieved by means of additively manufactured W skeletons consecutively infiltrated by Cu. Investigations with W preforms produced by Laser Beam Powder Bed Fusion and infiltrated by Cu demonstrate the feasibility of this approach while testing of specifically prepared specimen is ongoing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

Report on FY18 results on effects of sodium exposure on tensile properties and microstructure of Grade 91 steel

This report provides an update on the understanding of the effect of sodium exposures on microstructure and tensile properties of Grade 91 (G91) steel in support of the design and operation of G91 components in sodium-cooled fast reactors (SFRs). The report is a Level 3 deliverable in FY18 (M3NT- 18AN050503022), under the Work Package NT-18AN05050302, “G91 Sodium Compatibility” performed by the Argonne National Laboratory (ANL), as part of the Advanced Materials Development Program for Fast Reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1976

Matrix of educational and training materials in remote sensing

Remote sensing educational and training materials developed by LARS have been organized in a matrix format. Each row in the matrix represents a subject area in remote sensing and the columns represent different types of instructional materials. This format has proved to be useful for displaying in a concise manner the subject matter content, prerequisite requirements and technical depth of each instructional module in the matrix. A general description of the matrix is followed by three examples designed to illustrate how the matrix can be used to synthesize training programs tailored to meet the needs of individual students. A detailed description of each of the modules in the matrix is contained in a catalog section.

Lindenlaub, J. C.↗
NASA NTRS1986

Development in tunable solid state lasers with high spectral purity, high efficiency and long lifetime for differential absorption lidar

The paper presents a review of tunable vibronic solid state lasers for DIAL measurements and provides new experimental results for tunable Ti:sapphire lasers, materials development, and spectral bandwidth narrowing through injection control. Pulsed injection control of a Ti:sapphire laser with a 2.5-pm narrow band pulsed dye laser and with another Ti:sapphire laser is demonstrated with nearly complete energy extraction, indicating homogeneous line broadening. The status of tunable solid state lasers in the 1.6-2.3 micron range for DIAL measurements of trace gases, and development trends for lasers with reduced cryogenic cooling needs, are included. The effects of laser gain on optical damage, energy extraction, and amplified spontaneous emission are indicated for several tunable lasers.

Hess, R. V.↗
NASA NTRS2005

Glenn Refractory Adhesive for Bonding and Exterior Repair (GRABER) Developed for Repairing Shuttle Damage

Advanced in-space repair technologies for reinforced carbon/carbon composite (RCC) thermal protection system (TPS) structures are critically needed for the space shuttle Return To Flight (RTF) efforts. These technologies are also critical for the repair and refurbishment of thermal protection system structures of future Crew Exploration Vehicles of space exploration programs. The Glenn Refractory Adhesive for Bonding and Exterior Repair (GRABER) material developed at the NASA Glenn Research Center has demonstrated capabilities for repair of small cracks and damage in RCC leading-edge material. The concept consists of preparing an adhesive paste of desired ceramic in a polymer/phenolic resin matrix with appropriate additives, such as surfactants, and then applying the paste into the damaged or cracked area of the RCC composite components with caulking guns. The adhesive paste cures at 100 to 120 C and transforms into a high-temperature ceramic during simulated vehicle reentry testing conditions.

Singh, Mrityunjay↗