Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Effect of Processing on Precipitation Kinetics in Nano Polycrystalline 7075 Aluminum Alloy

Fairmount Technologies (FT) seeks to optimize the thermomechanical processing of Aluminum Alloy 7075. The target yield strength is 20% higher than commercially available 7075-T6 temper sheet which will enable structural light weighting by a similar magnitude and reduce the carbon footprint of the transportation sector. To reduce processing cost and make this commercially viable, it is important to understand physical mechanisms driving microstructural changes. A mesoscale phase-field model seeded with experimentally measured microstructures and assessed thermodynamic and kinetic properties will be developed and exercised using HPC at PNNL. It will account for the effect of deformation, temperature, and chemistry on precipitation kinetics in nanocrystalline microstructures. Our objective is to understand this “stress-aging” coupling by performing parametric simulations with mesoscale models for a better understanding of GP zone and η' formation in nanocrystalline 7075 Al. This will help FT optimize processing schedules to achieve desired microstructures that increase both strength and ductility.

36 MATERIALS SCIENCE↗

Microstructure-sensitive Crystal Viscoplasticity for Ni-base Superalloys Targeting Long-term Creep-Fatigue Interaction Modeling

This report introduces a new temperature-dependent, microstructure-sensitive crystal viscoplasticity model for single-crystal Ni-base superalloys. The model predicts the material response of the single-crystal components in the hot gas path sections of industrial gas turbines. The influence of changes in the microstructure that occur with aging in service, critical to predicting long-term creep-fatigue interactions, is embedded into the model through the γ' precipitate morphology evolution. The model is calibrated to predict the experimental response of CMSX-8, a lower cost variant of the second generation single-crystal superalloy CMSX-4. In addition, the experimentally-measured creep-fatigue and thermomechanical fatigue behavior of CMSX-8 is reported.

03 NATURAL GAS↗

Part-scale microstructure prediction for laser powder bed fusion Ti-6Al-4V using a hybrid mechanistic and machine learning model

Laser powder bed fusion (LPBF) Ti-6Al-4V is widely studied for use in structural applications in aerospace and medical industries, but mechanical anisotropy and microstructural inhomogeneity prohibits its wider adoption. Although successful microstructure prediction models have been developed, a remaining challenge is their limited integration across length/time scales and validation by experimental studies. Here, this work proposes a physics-augmented machine learning surrogate model to unite predictions of LPBF temperature, β phase morphology and texture, and α/α’ formation into a single framework that is calibrated and validated with experiments. First, a phase field (PF) model of the martensitic β→α’ transformation is developed and calibrated using data from in-situ synchrotron cyclic heating/cooling studies quantifying the variation of α phase fraction with time. In parallel, an established finite difference-Monte Carlo (FDMC) model predicts the part-scale temperature profile and β grain formation during solidification. A dataset is developed using LPBF cyclic temperature descriptors from the FDMC model as inputs and corresponding α/α’ phase fraction and width from the PF model as outputs. Five machine learning (ML) regression models are tested and optimized, having mean absolute error in testing ≤ 4 %, and the k-nearest neighbors (KNN) model is selected as the best performing. The KNN model is called at the nodal level during post-processing of the FDMC model to replace and downscale the response of the PF model. The combined agility and accuracy of the hybrid FDMC-ML model enables part-scale microstructure predictions that can be further used for property predictions to accelerate AM process optimization.

36 MATERIALS SCIENCE↗

Convoluted filtering for process cycle modeling

Principles of materials science and engineering, physics, mathematics, and information science are used to extract knowledge and insights from the process-structure–property-performance relationships hidden in materials data. The process-structure modeling can be accelerated without loss of interpretability, with artificial intelligence tools that mimic the salient features of the process and process-structure relations. In this work, a novel convoluted model-filtering technique was exploited to build and successfully train the Convoluted Filter (CoFi) artifacts for Fe-based alloy heat treatment cycles. The artifacts were pre-trained to filter out deep models that change the surrogate microstructure state after the heat treatment at ambient conditions. Direct representation of the thermal cycle features within knowledge Graph facilitated development of meaningful data models for microstructure evolution, which reduce overfitting to limited datasets.

36 MATERIALS SCIENCE↗

NEAMS Software V&V Plan for the MARMOT Software

In order to ensure the accuracy and quality of the microstructure based materials models being developed in conjunction with MARMOT simulations, MARMOT must undergo exhaustive verification and validation. Only after this process can we confidently rely on the MARMOT code to predict the microstructure evolution within the fuel. Therefore, in this report we lay out a V&V plan for the MARMOT code, highlighting where existing data could be used and where new data is required.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quarterly Management Document – FY17, 3rd Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

Progress on modeling the the creep of thick sections welds in Alloy 740H is reported. Climb of dislocations during creep has been added to the model. Creep testing is continuing and stress drop testing has been initiated to determine the threshold stress of this particle-strengthened alloy. Work has also begun on generating synthetic microstructures, representative of experimental microstructures, from data collected with EBSD. This will enable incorporation of experimental microstructures into the modeling and simulation effort.

36 MATERIALS SCIENCE↗

Investigation of radiation damage tolerance in interface-containing metallic nano structures

The proposed work seeks to conduct a basic study by applying experimental and computational methods to obtain quantitative influence of helium sink strength and proximity on He bubble nucleation and growth in He-irradiated nano-scale metallic structures, and the ensuing deformation mechanisms and mechanical properties. We utilized a combination of nano-scale in-situ tension and compression experiments on low-energy He-irradiated samples combined with site-specific microstructural characterization and modeling efforts. We also investigated the mechanical deformation of nano-architected materials, i.e. nanolattices which are comprised of 3-dimensional interwoven networks of hollow tubes, with the wall thickness in the nanometer range. This systematic approach will provide us with critical information for identifying key factors that govern He bubble nucleation and growth upon irradiation as a function of both sink strength and sink proximity through an experimentally-confirmed physical understanding. As an outgrowth of these efforts, we performed irradiations with self-ions (Ni 2+ ) on Ni-Al-Zr metallic glass nanolattices to assess their resilience against radiation damage rather than He-ion implantation. We focused our attention on studying individual bcc/fcc interfaces within a single nano structure (nano-pillar or a hollow tube): a single Fe (bcc)-Cu (fcc) boundary per pillar oriented perpendicular to the pillar axes, as well as pure bcc and fcc nano structures. Additional interfaces of interest include bcc/bcc and metal/metallic glass all within a single nano-structure volume. The model material systems are: (1) pure single crystalline Fe and Cu, (2) a single Fe (bcc)-Cu (fcc) boundary per nano structure (3) a single metal–metallic glass, all oriented non-parallel to the loading direction so that their fracture strength can be tested. A nano-fabrication approach, which involves e-beam lithography and templated electroplating, as well as two-photon lithography, was utilized, which enabled precise control of the initial microstructure control. Experimentally determined stress-strain relationships were enhanced by in-situ SEM observations coupled with TEM microstructural characterization of the same samples before and after deformation (irradiated and as-fabricated) and atomistic (MD) modeling. A comprehensive suite of experiments was conducted to quantitatively assess the key parameters for He bubble nucleation and growth by independently varying the sink strength, sink proximity, and He implantation temperature and dose. The implantations were conducted at Sandia and Los Alamos National Labs (CINT). Nano structuress containing He-enriched interfaces and irradiation-damaged microstructure were tested under uniaxial tension to assess embrittlement, resulting boundary strength, and deformation mechanisms. Results of this work helped identify which types of interfaces are particularly resilient against radiation damage.

36 MATERIALS SCIENCE↗

A crystal plasticity finite element method modeling of Zircaloy with hydride phases based on scanning electron micrographs

This work developed a microstructure-based finite element model to predict the stress state of alloys with second phase inclusions. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. Generation of digital microstructure was achieved through two steps of tessellations using software Neper and Matlab. The process is demonstrated using an example of Zircaloy material with secondary phases of hydrides dispersed within and stress-strain response of Zircaloy containing hydrides was predicted. The constitutive material model for Zircaloy in this study was based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as isotropic elasto-plastic material. A parametric study had been conducted to understand the effect of volume fraction, and lamellae thickness of the hydride phase on the mechanical properties of the overall material. Results can help designers to alter the manufacturing process to obtain the enhanced mechanical properties for components used in nuclear applications made by Zircaloy material.

Kulkarni, Shank S.↗

Relating microstructure, temperature, and chemistry to explosive ignition and shock sensitivity

An analysis is put forth that relates explosive properties including microstructure, temperature, and chemistry to explosive ignition and sensitivity. Unlike approaches that focus only on elucidating mesoscopic mechanisms important to ignition, the present analysis seeks a methodology directly applicable to continuum explosive burn models. Because the Scaled Uniform Reactive Front (SURF) burn model has a microstructural basis, it is chosen as the starting point of the present analysis. To build upon the SURF framework, a literal translation is performed of the high-level conceptual notions for which SURF is based, to concrete ignition–combustion parameters, a statistical description of the microstructure, and other thermo-chemical data acquired by non-shock experiments. The analysis requires a void volume fraction distribution acquired from ultra-small angle neutron scattering (USANS). The shock response of PBX 9502 is used to illustrate the theory. While the analysis requires calibration to a shock experiment (the pop plot, for example), the results are a self-consistent set of realistic physical quantities that contribute to the shock initiation process including, initial temperature, chemical kinetics, a statistical description of the microstructure, and the hot spot size, spacing, and temperature. The utility of having a mesoscale based theory is that once the critical hot spot temperature, as a function of shock pressure, is known for a given explosive and initial porosity distribution, the entire set of meso- and macro-scale results, including the pop plot can be calculated for any other porosity. Thus, one can understand changes in sensitivity at different densities (void size distributions), relying only on the assumption that the hot spot temperature curve would not differ significantly if the morphology of the hots spots were similar. Another important utility of the present analysis is to address the question of the role of initial temperature on the observed shock sensitivity of PBX 9502 and other explosives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis

Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.

36 MATERIALS SCIENCE↗

Report on the Integration of Experimental and Modeling Data for Initial Equivalence Study of Microstructural Evolution in Irradiated LPBF 316SS

Advanced materials and manufacturing technologies are poised to improve the safety and design characteristics of nuclear technologies and meet US energy, environmental, and economic needs. In particular, metal additive manufacturing (AM) provides an opportunity to produce novel materials and component geometries, but their use is not without hurdles arising from the inherent microstructure variability that can result from the layer-by-layer build approach. Given the greater possible microstructure variability in AM materials—and the dearth of materials test reactors—it is impractical to rely solely on neutron irradiation studies to produce data for materials qualification for every possibility. This work within the Advanced Materials and Manufacturing Technologies (AMMT) Environmental Effects technical area contributes to the rapid qualification framework by developing a science-driven framework for the accelerated qualification of materials for nuclear environments. A key product of the Environmental Effects technical area of the AMMT program is the Licensing Approach with Ions and Neutrons (LAIN). This approach recognizes that whether using existing materials in new environments, newly developed materials tailored for these environments, or new manufacturing methods, the traditional decades-long approach for materials qualification does not facilitate rapid deployment. In FY 2023, the AMMT program presented a conceptual framework of specific steps to fulfill several technical challenges associated with qualifying materials for performance in radiation environments on an accelerated time frame informed by the state of the art in materials science and a review of the current regulatory landscape. The objective of this section of the Environmental Effects technical area is to critically evaluate and refine the proposed qualification framework presented under AMMT by integrating the research results of the neutron irradiations, the ion irradiations, and modeling efforts. These ongoing efforts span across Argonne National Laboratory (ANL), Idaho National Laboratory (INL), and Oak Ridge National Laboratory (ORNL) and are closely coordinated.

36 MATERIALS SCIENCE↗

Assessment of Process Modeling Tools for Determining Variability in Additively Manufactured Parts

The Advanced Materials and Manufacturing Technologies (AMMT) program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy However, the unique aspects of additive manufacturing (AM) materials in terms of their processing history, microstructure, and properties, are a major barrier for qualification and certification of nuclear components. Much of this challenge may be attributed to component scale variations in microstructure and properties that are driven by local influences of process conditions and geometry on thermal history, melt pool dynamics, and corresponding microstructure evolution. Computational modeling tools may be helpful in this regard to aid in predicting and controlling this level of variability. The purpose of this report is to review the current state-of-the-art for process modeling with regards to metal AM. For this purpose, we consider specifically the case study of laser powder bed fusion (LPBF) processing of SS316, a family of alloys that are both commonly used in nuclear energy applications and suitable for AM processing. The report first introduces the necessary components of a process modeling workflow, followed by a review of the current status of each. At the end, application of these modeling tools to understanding variability in AM process given their current state are considered, and recommendations for future development are proposed

36 MATERIALS SCIENCE↗

Toward a machine-guided approach to energetic material discovery

In this article, we trained a machine learning (ML) model to connect microstructural details of an energetic material formulation to its performance for the purpose of guiding the discovery of new explosive formulations. Our hypothesis was that the algorithm would robustly learn the training data and produce an accurate surrogate model. Specifically, the algorithm learned the relationship between details of the void size distribution (VSD), initiating shock pressure, and the energetic material performance. We used realistic constraints on the VSD and a range of cases were ingested by a physically informed reactive flow model working within a hydrodynamic solver running on high-performance computing resources. The ML algorithm produced a surrogate model that accurately predicted known test points around the parameter space. In addition to the utility of the model and the process used for its development, we noted interesting comparisons between what we, the authors—subject matter experts, would heuristically conclude from the training data and the surrogate model predictions. We detected nuanced details that were missed by the surrogate model; however, these details are not important to an energetic material formulator. We concluded that the algorithm did indeed robustly learn the training data and produce an accurate surrogate model. We further concluded that the surrogate model is a powerful tool to guide the formulator in the absence of subject matter experts and limited-access computing resources.

42 ENGINEERING↗

A microstructure sensitive grain boundary sliding and slip based constitutive model for machining of $\mathrm{Ti}$-$\mathrm{6Al}$-$\mathrm{4V}$

We report a composite dual phase internal state variable constitutive model was developed for Ti-6Al-4V. The proposed model includes diffusion assisted grain boundary sliding based physics in addition to a traditional slip-based plasticity. Influence of microstructure on the flow stress is introduced via dislocation density and mean grain size internal state variables. The dislocation density evolves according to a physics based law that considers dislocation nucleation and annihilation processes. Grain refinement is driven by dynamic recrystallization, which is modeled phenomenologically. The model is calibrated with uniaxial stress–strain data that ranges between quasi-static and dynamic rates across a wide range of temperatures. Validation against machining data shows that the model predicts chip segmentation frequency, machining forces, and tool temperatures reasonably well. The newly introduced grain boundary sliding physics was found to dominate deformation following sufficient grain refinement. This deformation mode provides softening at the constitutive level without the need for invoking damage based softening mechanisms. This physical interpretation is something that has not previously been explored in the machining literature.

36 MATERIALS SCIENCE↗

Developing the Oxidation Kinetic Model for Magnetite Pellet

Oxidation is a vital phenomenon for magnetite pellets in their excursion through the furnace during induration. One of the pre-requisites for magnetite pellets to achieve homogeneously structured good quality pellets is to have complete oxidation before sintering begins. Partially oxidized magnetite pellets, upon sintering, might result in inhomogeneous structured pellets which could be detrimental to pellet quality. It is necessary to understand the mechanisms responsible for magnetite oxidation, and hence, it is intended in this study to investigate experimentally as well as develop a mathematical model based on oxidation kinetics. Oxidation of pellets is largely influenced by the oxidation kinetics of particles and hence should be studied at particle as well as at pellet scale. The principles of the Grain Model have been adopted to develop the Oxidation Model at pellet scale, whereas the particles’ oxidation follows the Avrami Kinetic Model. Isothermal oxidation experiments performed Thermogravimetric Analyzer showed that oxidation rate of magnetite at pellet scale contained two peaks. They were complemented well by oxidation rates predicted from the model. Further, the pellet was investigated microstructurally at pellet and particle scale to substantiate the findings from the experiments and the model. The oxidation model developed is used to predict the progression of oxidation in the magnetite pellet with respect to the reaction time at three different temperatures (873 K, 973 K, and 1073 K (600 °C, 700 °C, and 800 °C)) and at four levels of oxygen (0.21, 0.30, 0.60, and 1.00 atm) in the oxidizing gas.

36 MATERIALS SCIENCE↗

Thermal Microstructural Stability of AZ31 Magnesium after Severe Plastic Deformation

Both equal channel angular pressing and friction stir processing have the ability to refine the grain size of twin roll cast AZ31 magnesium and potentially improve its superplastic properties. This work used isochronal and isothermal heat treatments to investigate the microstructural stability of twin roll cast, equal channel angular pressed and friction stir processed AZ31 magnesium. For both heat treatment conditions, it was found that the twin roll casted and equal channel angular pressed materials were more stable than the friction stir processed material. Calculations of the grain growth kinetics showed that severe plastic deformation processing decreased the activation energy for grain boundary motion with the equal channel angular pressed material having the greatest Q value of the severely plastically deformed materials and that increasing the tool travel speed of the friction stir processed material improved microstructural stability. The Hollomon-Jaffe parameter was found to be an accurate means of identifying the annealing conditions that will result in substantial grain growth and loss of potential superplastic properties in the severely plastically deformed materials. In addition, Humphreys’s model of cellular microstructural stability accurately predicted the relative microstructural stability of the severely plastically deformed materials and with some modification, closely predicted the maximum grain size ratio achieved by the severely plastically deformed materials.

FSW↗