Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Effect of doping, microstructure, and CO{sub 2} on La{sub 2}NiO{sub 4+{delta}}-based oxygen-transporting materials

Alkaline earth-free La{sub 2}NiO{sub 4+{delta}} based materials were synthesized by a sol-gel method and studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques as well as oxygen permeation experiments. Effects of doping the nickel position with a variety of cations (Al, Co, Cu, Fe, Mg, Ta, and Zr) were investigated with regards to oxygen flux and microstructure. Doping was always found to diminish the oxygen flux as compared to the reference composition. However, larger grains, which were achieved by longer annealing times at 1723 K have a minor negative impact on oxygen permeation flux in case of La{sub 2}NiO{sub 4+{delta}} and La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}} system. Moessbauer spectroscopy shows that the iron-doped system exhibits a secondary phase, which was identified by high-resolution transmission electron microscopy (HRTEM) as a higher Ruddlesden-Popper phase. In-situ XRD in an atmosphere containing 50 vol% CO{sub 2} and long-term oxygen permeation experiments using pure CO{sub 2} as the sweep gas revealed a high tolerance of the materials towards CO{sub 2}. - Graphical Abstract: The vibrational polished La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}} membrane revealed formation of secondary phases, which were confirmed by Moessbauer spectroscopy. Highlights: Black-Right-Pointing-Pointer La{sub 2}NiO{sub 4+{delta}} systematically doped with different valent cations. Black-Right-Pointing-Pointer Large grains have a negative impact on oxygen-permeation performance. Black-Right-Pointing-Pointer CO{sub 2}-stability proved by in-situ XRD in 50 vol% CO{sub 2}. Black-Right-Pointing-Pointer Constant long-term permeation in presence of CO{sub 2}. Black-Right-Pointing-Pointer Moessbauer and TEM reveal multiple phases in La{sub 2}Ni{sub 0.9}Fe{sub 0.1}O{sub 4+{delta}} system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of AlN/Al Polycrystals along with Al Nanoparticles Using Thermal Plasma Route

This paper for the first time reports the (200) oriented growth of hexagonal Aluminum nitride crystals during synthesis of aluminum nanoparticles in dc transferred arc thermal plasma reactor by gas phase condensation in nitrogen plasma. The structural and morphological study of as synthesized AlN crystal and aluminium nanoparticles was done by using the x-ray diffraction method, scanning electron microscopy and transmission electron microscopy.

36 MATERIALS SCIENCE↗

Exotic Long-Range Surface Reconstruction on La 0.7 Sr 0.3 MnO 3 Thin Films

Due to an extremely diverse phase space, La 1–x Sr x MnO 3 , as with other manganites, offers a wide range of tunability and applications including colossal magnetoresistance and use as spin-polarized electrodes. Here, we study an unprecedented, exotic surface reconstruction (6 × 6) in La 1–x Sr x MnO 3 (x = 0.3) observed via low-energy electron diffraction (LEED). Scanning tunneling microscopy (STM) shows the surface is relatively flat, with unit-cell step heights, and X-ray photoelectron spectroscopy (XPS) reveals a strong degree of Sr segregation at the surface. By combining electron diffraction and first-principles computations, we propose that the long-range surface reconstruction consists of a Sr-segregated surface with La (6 × 6) ordering. This study expands our understanding of manganite systems and underscores their ability to form interesting surface reconstructions, driven largely by cation segregation that can potentially be controlled for tuning surface ordering.

36 MATERIALS SCIENCE↗

Synthesis of Bi{sub 2}S{sub 3} with different sulfur content by conventional high temperature solid state solvothermal route

Bismuth sulfide (Bi{sub 2}S{sub 3}) is a binary chalcogenide compound material belonging to V-VI group of semiconductors. Because of its direct band gap of 1.3 eV and high figure of merit (ZT) value, it is widely used as a thermo electronic-cooling material based on the Peltier effect. The electrical and optical property of Bi{sub 2}S{sub 3} material is strongly dependent on stoichiometric composition, defect chemistry and structure. In this study, we have synthesized Bi{sub 2}S{sub x} (x = 3.15, 3.30, 3.45) compound material with different sulfur content by conventional high temperature solid state solvothermal reaction of bismuth and sulfur. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDXS) analysis of synthesized compound materials were carried out to observe crystallinity, surface morphology and composition of elements in the compound. The optical analysis revealed that energy band gap decreases with increase of sulfur content.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Antibacterial and Structural Properties and Printability of Starch/Clay/Polyethylene Composite Films

A composite of thermoplastic starch (TPS), low-density polyethylene (LDPE) and citric acid-modified montmorillonite (CMMT) was prepared in a twin screw extruder for packaging film application. Starch was first converted to the thermoplastic state by using sorbitol and water. Composite films were produced on a chill roll system and then were modified for printability by grafting of acrylonitrile onto the starch backbone. Antimicrobial property and printability of the films were studied from which the sample with the highest antimicrobial property and the best printability was selected. This optimal sample was then characterized by Fourier transform infrared, thermal gravimetric analysis, differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy. The composite film showed a matrix/dispersed morphology in which LDPE formed a continuous phase and TPS/CMMT nanocomposite particles appeared as dispersed phase. Biodegradability, water absorption, oxygen permeability, tensile strength and transparency of optimal film were also studied. The results indicated very good properties of the produced composite film for packaging application. Graphical Abstract: .

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Y{sub 2}BaCuO{sub 5} Nanoparticle Doping on Critical Current Density of YBa{sub 2}Cu{sub 3}O{sub 7-δ} Bulk Superconductor

This study presents the effect of Y{sub 2}BaCuO{sub 5} (Y211) nanoparticle doping on critical current density and critical temperature of YBa{sub 2}Cu{sub 3}O{sub 7-δ} (YBCO) superconductor. Y211 nanoparticles with different particle sizes ranging from 34 to 455 nm were synthesized by a sol-gel method, then doped into the YBCO superconductor by 0.5, 1, and 2 wt.%. Samples were characterized using X-ray diffraction and scanning electron microscope measurements. The standard four-probe technique was used to measure the critical current density at 77 K. The results showed that in the all-doped samples, critical current density was higher than that of the pure sample. It was found that in the samples containing 1 and 2 wt.% of Y211 nanoparticles, by increasing the size of nanoparticles, the J{sub c} was increased, but in samples containing 0.5 wt.%, the J{sub c} decreased. The maximum critical current density of 64 A/cm {sup 2} was obtained for the samples doped with 2 wt.% of 455 nm Y211 nanoparticles. Also, it was observed that the critical temperature slightly decreased with nanoparticle doping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sticking-Free Reduction of Titanomagnetite Ironsand in a Fluidized Bed Reactor

Fluidized bed reduction of iron ore fines is typically inhibited by the onset of “sticking” at temperatures above 973 K, which leads to particle agglomeration and defluidization of the bed. Here, we report the sticking-free fluidized bed reduction of titanomagnetite (TTM) ironsand at 1223 K in Ar-H{sub 2} gas mixtures. We show that sticking is prevented by the formation of a protective titanium-rich oxide shell around each particle during the initial reduction stage. This protective shell prevents iron-iron contact between particles throughout the reduction process, enabling metallization degrees of 93 pct to be attained without sticking occurring. Phase evolution during the reaction has also been analyzed using q-X-ray diffraction and scanning electron microscope/energy dispersed spectroscopy. We find that the reduction proceeds through four separate stages. During the initial stage, approximately half of the initial TTM phase is converted to wüstite, forming a network of sub-micron wüstite channels which interlace the TTM matrix. During this stage, Ti and Al are enriched within the TTM matrix, due to the low solubility of both species in wüstite. This enrichment stabilizes the remaining TTM, meaning that wüstite is then preferentially reduced to metallic iron in stage 2 of the reduction. In stage 3, the remaining Ti-enriched TTM is reduced directly to metallic iron and ilmenite. The final stage of reduction involves the conversion of ilmenite into rutile and pseudobrookite. Our findings clarify the important role played by titanium species during the reduction of TTM and suggest that New Zealand ironsand can offer significant advantages over conventional hematite ores when used as a feedstock for fluidized bed direct-reduced iron processes.

36 MATERIALS SCIENCE↗

Effect of Ca and Sm Combined Addition on the Microstructure and Elevated-Temperature Mechanical Properties of Mg-6Al Alloys

In the present study, the microstructure and elevated-temperature mechanical properties of Mg-6Al, Mg-6Al-4Ca, Mg-6Al-4Sm and Mg-6Al-2Ca-2Sm alloys were investigated. The experimental results showed that the microstructure and elevated-temperature mechanical property of Mg-6Al alloy changed obviously with the different elements addition. By analyzing the results of optical microscope, x-ray diffraction analysis, scanning electron microscope, and transmission electron microscope, it could be determined that there was only Mg{sub 17}Al{sub 12} phase in Mg-6Al alloy, there were Al{sub 2}Ca and (Mg, Al){sub 2}Ca phases in Mg-6Al-4Ca alloy, there were Al{sub 2}Sm and Mg{sub 17}Al{sub 12} phases in Mg-6Al-4Sm alloy, and there were (Mg, Al){sub 2}Ca, Al{sub 2}Ca and Al{sub 2}Sm phases in Mg-6Al-2Ca-2Sm alloy. In addition, the addition of alloying elements including Ca and Sm, especially the composite addition, could significantly improve the tensile properties of Mg-6Al alloy. Compared to Mg-6Al alloy, the tensile strengths of Mg-6Al-2Ca-2Sm alloy at 448, 473 and 498 K were enhanced by 50.32, 87.92, and 94.99%, respectively. Furthermore, when the stretching temperatures were 448 and 473 K, the fracture pattern of Mg-6Al-2Ca-2Sm alloy was the mixture of intergranular fracture and trans-crystalline fracture. However, when the stretching temperature was 498 K, the fracture pattern of Mg-6Al-2Ca-2Sm alloy was the intergranular fracture.

36 MATERIALS SCIENCE↗

Pure and cerium-doped zinc orthosilicate as a pigment for thermoregulating coatings

Microwave-assisted hydrothermal synthesis followed by high-temperature (1050 °C) calcination was used to prepare pure and cerium-doped zinc orthosilicate (Zn 2 SiO 4 ) pigments. Nanoscale Zn 2 SiO 4 and Ce–Zn 2 SiO 4 powders were blended with potassium silicate (K 2 SiO 3 ) and then applied to the aluminum substrate to obtain thermoregulating coatings. Electron beams with different energies were used to irradiate nanoscale pigment powders and coatings. X-ray diffraction (XRD), scanning electron microscopy (SEM), and transition electron microscopy (TEM) were used to characterize the phase composition, morphology, and atomic-level structure of materials. Here, the diffuse reflectance and absorption measurements of materials before and after irradiation indicated that Ce–Zn 2 SiO 4 -based coatings exhibit better radiation resistance compared to pure Zn 2 SiO 4 . Simple and straightforward preparation, as well as high radiation resistance, make Ce–Zn 2 SiO 4 -based thermoregulating coatings excellent candidates for space vehicles.

36 MATERIALS SCIENCE↗

Low Temperature Milling of the LiNH2 + LiH Hydrogen Storage System

Ball milling of the LiNH2 + LiH storage system was performed at 20°C, -40°C, and -196°C, and the resulting powders were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), nuclear magnetic resonance (NMR), specific surface area (SSA) analysis, and kinetics cycling measurements. Ball milling at -40°C showed no appreciable deviations from the 20°C sample, but the -196°C powder exhibited a significant increase in the hydrogen desorption kinetics. NMR analysis indicates that a possible explanation for the kinetics increase is the retention of internal defects generated during the milling process that are annealed at the collision site at higher milling temperatures.

08 HYDROGEN↗

Effect of Ca Doping on the Electrical Conductivity of the High-Temperature Proton Conductor LaNbO4

The sintering properties, crystal structure and electrical conductivity of La1-xCaxNbO4- (x=0, 0.005, 0.01, 0.015, 0.02 and 0.025), prepared by a conventional solid-state method, have been investigated using powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). In 2.5% Ca doped samples, a small amount of impurities Ca2Nb2O7 were observed from the XRD patterns. Impedance spectra show that the grain boundary resistance increases with increasing Ca content, while the bulk resistance remains essentially constant below 550 C. Despite the higher degree of grain growth was observed for higher Ca-doping levels, the total conductivity of the La1-xCaxNbO4- series decreases with increasing Ca content from 0.5 to 2.0 mol%. The activation energy for the total conductivity decreases with increasing Ca content from 0.71 eV (x=0) to 0.54 eV (x=0.01) for the high temperature tetragonal phase, then it increases to 0.60 eV for x=0.02. For the monoclinic phase, La0.995Ca0.005NbO4- shows the lowest activation energy of 1.26 eV. These results imply that the solubility of CaO in LaNbO4 is in the range from 0.5 to 1.0 mol%. By increasing the sintering temperature from 1500 C to 1550 C, the proton conductivity of the Ca-doped LaNbO4 was improved with enlarged grain size due to a reduction in the resistive grain boundary contribution.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Preparation and photocatalytic activity for water splitting of Pt-Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays

Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays were prepared by hydrothermal method from Ta{sub 2}O{sub 5} nanotube arrays, obtained by anodization of Ta foils, in Na{sub 2}CO{sub 3} solution at 150 Degree-Sign C. The as-synthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), UV-vis diffuse reflectance spectra (UV-DRS) and X-ray photoelectron spectroscopy (XPS). Analysis results show that pyrochlore structure Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays have been successfully fabricated. The diameters and lengths of Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays are 50 nm and 4 {mu}m, respectively. The photocatalytic hydrogen production activities of the as-synthesized Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays are highly dependent on the hydrothermal reaction time and Na{sub 2}CO{sub 3} concentration, optimized reaction parameters are obtained. To further improve the photocatalytic activity for hydrogen evolution, Pt loaded Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays are prepared by photochemical reduction method. The Pt loaded samples exhibit much higher activity for hydrogen evolution than pure Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays. Moreover, the photocatalytic hydrogen properties are rather stable. - Graphical abstract: Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays were synthesized by hydrothermal method using Ta{sub 2}O{sub 5} nanotube arrays as a precursor. The loaded Pt enhances the photocatalytic activity for water splitting of Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays. Highlights: Black-Right-Pointing-Pointer Novel Na{sub 2}Ta{sub 2}O{sub 6} nanotube array films with pyrochlore structure were synthesized. Black-Right-Pointing-Pointer Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays are active for H{sub 2} evolution from aqueous CH{sub 3}OH solution. Black-Right-Pointing-Pointer The effect of hydrothermal conditions on photocatalytic activity was investigated. Black-Right-Pointing-Pointer Pt loading can improve the photocatalytic activities of Na{sub 2}Ta{sub 2}O{sub 6} nanotube arrays. Black-Right-Pointing-Pointer Photocatalytic mechanism is proposed based on the experimental results.

36 MATERIALS SCIENCE↗

Synthesis and characterization of barium ferrite–silica nanocomposites

In this work, we prepared barium ferrite-silica (BaM-SiO{sub 2}) nanocomposites of different molar ratios by high-energy ball milling, followed by heat-treatment at different temperatures. The microstructure, morphology and magnetic properties were characterized for different synthesis conditions by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometry (VSM). The results indicate that 15 h of milling was enough to avoid the generation of hematite phase and to get a good dispersion of barium ferrite particles in the ceramic matrix. For milling periods beyond 15 h and heat treatment above 900 °C, the XRD patterns showed the presence of hematite phase caused by the decomposition of BaM. The agglomerate size observed through SEM analysis was around 150 nm with a good BaM dispersion into the SiO{sub 2} matrix. The highest saturation magnetization (Ms) value obtained was 43 emu/g and the corresponding coercivity (Hc) value of 3.4 kOe for the composition 60BaM-40SiO{sub 2} milled for 15 h and heat treated at 900 °C. This coercivity value is acceptable for the application in magnetic recording media. Highlights: • Barium ferrite–silica nanocomposites were prepared by high energy ball milling. • Optimal processing time is 15 h milling and heat treatment at 900 °C. • This is enough to avoid the generation of hematite phase. • Obtain good dispersion of barium ferrite particles in the ceramic matrix • Above this processing time shows the presence of increased amount of hematite.

36 MATERIALS SCIENCE↗

New insights on the formation of supersaturated Cu-Nb solid solution prepared by mechanical alloying

The deformation-driven alloying mechanisms in the immiscible Cu-Nb system during mechanical alloying (MA) process have been studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) observations. It is found that the dominating alloying mechanism changes at the different stages of milling. Initially, the alloying process is mainly governed by interfaces and dislocations, which supply fast diffusion channels between phases. In the intermediate stage, Nb particles with sizes below 8 nm undergo a bcc to fcc allotropic transformation, and the interdiffusion between fcc-Nb and fcc-Cu is promoted due to the similarity of lattice structures. Further milling generates disclination defects, which contribute to the formation of fragments or subgrains with sizes below 5 nm. The introduction of such defects and fragments benefits the formation of a complete Cu-Nb solid solution. The formation kinetics of solid solution is analyzed by Johnson-Mehl-Avrami equation, which suggests that the speed of the diffusion of Nb atoms into Cu is very slow. - Highlights: •The bcc to fcc transformation in Nb nanoparticles promotes diffusion process. •The formation of fragments with sizes below 5 nm is attributed to the disclination defects. •Defect-assisted diffusion is responsible for the alloying process.

36 MATERIALS SCIENCE↗

Microstructure and nanoindentation analysis of Mg-SiC nanocomposite powders synthesized by mechanical milling

Highlights: • Mechanical milling as an effective solution to reach a homogeneous distribution of SiC nanoparticles up to 10 vol% in Mg matrix • No deformation twinning in the nanostructured Mg matrix even after the severe plastic deformation and hard SiC nanoparticles up to 10 vol%. • Significant enhancement of nanohardness and reduced elastic modulus in the milled nanocomposite powders - Abstract: Mixtures of magnesium powder and SiC nanoparticles at various volume fractions were mechanically milled to produce nanocrystalline Mg-SiC nanocomposites. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were utilized to characterize the microstructure of the milled powders. The microstructural evidences revealed that mechanical milling is a proper method to achieve a uniform distribution of the SiC nanoparticles, even up to 10% in the Mg matrix. Based on the results, higher volume fraction of the SiC nanoparticles raise the value of measured microstrain and reduce the crystallite size of the Mg matrix. The TEM results pointed to the fact that no deformation twinning takes place in the nanostructured Mg matrix even after severe plastic deformation through mechanical milling and the presence of hard SiC nanoparticles up to 10 vol%. The effects of nanoparticle volume fraction on mechanical properties of the milled Mg-SiC nanocomposites were evaluated using nanoindentation tests. The results clearly showed a significant enhancement of nanohardness and reduced elastic modulus in the milled powders compared to that of the reference material namely as-received pure magnesium. It was found that the SiC nanoparticles (even up to 10 vol%), well distributed in the magnesium matrix, remarkably improve the reduced elastic modulus and nanohardness of the nanocomposite powders.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Photoluminescence properties of NaGd(MoO{sub 4}){sub 2}:Eu{sup 3+} nanophosphors prepared by sol-gel method

NaGd(MoO{sub 4}){sub 2}:Eu{sup 3+} (hereafter NGM:Eu) phosphors have been prepared by sol-gel method. The properties of the resulting phosphors are characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) spectra and decay curve. The excitation spectra of NGM:Eu phosphors are mainly attributed to O {yields} Mo charge-transfer (CT) band at about 282 nm and some sharp lines of Eu{sup 3+} f-f transitions in near-UV and visible regions with two strong peaks at 395 and 465 nm, respectively. Under the 395 and 465 nm excitation, intense red emission peaked at 616 nm corresponding to {sup 5}D{sub 0} {yields} {sup 7}F{sub 2} transition of Eu{sup 3+} are observed for 35 at.% NGM:Eu phosphors as the optimal doping concentration. The luminescence properties suggest that NGM:Eu phosphor may be regarded as a potential red phosphor candidate for near-UV and blue light-emitting diodes (LEDs).

36 MATERIALS SCIENCE↗

Synthesis and photochromic properties of EDTA-induced MoO{sub 3} powder

Graphical abstract: The MoO{sub 3} powder, which exhibits highly dispersed floral aggregated-like structure built up by superimposed and staggered nanoflakes with a diameter of 1-1.5 {mu}m and a thickness of 0.1-0.2 {mu}m, has been successfully obtained when the molar ratio of EDTA/Mo{sup 6+} is 0.05:1. The EDTA inducer obviously enlarges the surface area and apparently enhances the reactivity of MoO{sub 3} powders, making it show greater absorptive capacity to the excitation light and better photochromic properties than the pure MoO{sub 3} powder. Highlights: {yields} EDTA as organic inducing agent. {yields} EDTA inducer at EDTA/Mo{sup 6+} molar ratio of 0.05:1 enables growth of flower-like microspheres. {yields} The formation of flower-like MoO{sub 3} makes its photochromic properties strongly enhanced. -- Abstract: In this study, the photochromic MoO{sub 3} powder with novel morphology has been synthesized via hydrothermal method, using ethylene diamine tetraacetice acid (EDTA) as organic inducing agent. The influence of EDTA on the morphology, structure and photochromic properties of MoO{sub 3} powder has been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), as well as ultraviolet and visible spectroscopy (UV-vis) and color difference meter. When the molar ratio of EDTA/Mo{sup 6+} is 0.05:1, the EDTA-induced MoO{sub 3} powder is found to have 3D flower-like morphologies and excellent photochromic properties. Furthermore, the possible growth mechanism of the flower-like structure and the photochromic mechanism of MoO{sub 3} powder are also discussed in detail.

36 MATERIALS SCIENCE↗

Post-synthetic treatments on Ni{sub x}Mn{sub x}Co{sub 1-2x}(OH){sub 2} for the preparation of lithium metal oxides

Highlights: {yields} Ni{sub x}Mn{sub x}Co{sub (1-2x)}(OH){sub 2} were prepared and subjected to post-synthetic treatments. For the first time these treatments were applied within the synthetic solution. {yields} Extended treatments increased the presence of oxidized phase and particle size. {yields} Electrochemical active lithiated oxides were prepared from treated hydroxides. We discuss the impact of treatments on particle size and electrochemical properties. -- Abstract: A series of hydroxides Ni{sub x}Mn{sub x}Co{sub (1-2x)}(OH){sub 2} for x = 0.00-0.50 were prepared. These hydroxides were used as the precursors in the synthesis of electrochemical active lithiated mixed metal oxides, LiNi{sub x}Mn{sub x}Co{sub (1-2x)}O{sub 2}. The traditional co-precipitation method was used to synthesize the hydroxides and the effect of different post-synthetic treatments were tested. The solutions after co-precipitation of the hydroxides were heated under hydrothermal or microwave assisted hydrothermal conditions at 180 {sup o}C. All samples were analyzed with X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. We observed that the hydroxides undergo oxidation to an oxyhydroxide phase as the stoichiometry varies during their synthesis and with post-synthetic treatments. As the concentration of Ni and Mn increases in the sample, a mixture of both hydroxide and oxyhydroxide phases is obtained. SEM images demonstrate a sintering effect on the hydroxide particles after post-synthetic treatment, while XRD measurements on these samples show an increase in crystallinity and reduced turbostratic disorder. The oxides synthesized from these precursors demonstrate similar electrochemical performance with one another.

36 MATERIALS SCIENCE↗