Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Single-Component Average Velocity Profiles in the Wake of the Orion Crew Capsule at the National Transonic Facility

A minimally intrusive molecular tagging instrument measured single-component average velocity profiles in two planes in the wake of the Orion capsule with different heat shield configurations in the National Transonic Facility at the NASA Langley Research Center. Reynolds number effects at subsonic conditions have proven difficult to predict due to the largely separated wake flow. Therefore two measurement planes in the wake of the model were probed to measure the wake profile for different heat shield configurations and act as a validation reference for computational tools. Air testing included Mach numbers of 0.3, 0.5, and 0.7 at Reynolds numbers of 5.3 and 7.5 million. In cryogenic nitrogen, the instrument was employed under transient conditions during the facility warm up at M = 0.3 with decreasing Reynolds numbers from 16 million. An exhaustive list of the results is shown and discussed here. For free transition heat shield configurations, the size of the wake was found to increase with Mach number, yet remain constant with Reynolds number for low (M = 0.3) and high (M = 0.7) subsonic Mach numbers. However, intermediate Mach numbers (M = 0.5) showed that the wake was smaller at higher Reynolds numbers for the IDAT heat shield. The addition of surface roughness in the form of grit, known as the fixed transition cases, negated any Mach number dependence to the wake profile and increased the size of the wake for all cases.

Velocimetry↗
NASA NTRS2022

Ice Sheet Melt Water Profile Mapping Using Multi-frequency Microwave Radiometry

For understanding englacial hydrology and its impact on ice sheet mass balance, observations of the liquid water content (LWC) within the ice sheets are needed. Earlier studies have shown the complementary nature of multi-frequency microwave radiometer measurements to detect subsurface LWC distribution in addition to surface LWC, which is critical for understanding the seasonal melt dynamics of ice sheets. In this study, we used 1.4 GHz brightness temperature (TB) measurements from the NASA Soil Moisture Active Passive (SMAP) satellite, and 6.9, 10.7, 18.9, and 36.5 GHz TB measurements from the JAXA Global Change Observation Mission-Water Shizuku (GCOM-W) satellite to investigate the multi-frequency response at pan-Greenland scale. The melt indications derived at different frequencies show trends consistent with persistent seasonal subsurface melt water and delayed subsurface refreezing of the seasonal melt water. The result suggests that the seasonal subsurface persistent melt water occurrences that are not captured by the high-frequency retrievals are both temporally and spatially very significant.

Burgin, Mariko↗
NASA NTRS2022

Nickel Accounting for the Psyche Spacecraft

(16) Psyche is a metallic asteroid located in the asteroid belt between Mars and Jupiter. The composition of Psyche is unknown, but the scientific community believes it is composed primarily of iron, nickel, and silicates. The Psyche mission will be the first space mission to study this asteroid in close proximity, and as such, determining the elemental composition of the asteroid is one of the primary objectives of this mission. The spacecraft measures this elemental composition using the Gamma Ray Spectrometer (GRS), which detects cosmic-ray induced gamma rays from Psyche’s surface. In addition to gamma rays from Psyche, the GRS will also detect background gamma rays from spacecraft material nearby the GRS. Because Ni is such a key element for achieving the mission science objectives, a special effort has been made to minimize background gamma rays from Ni, thus maximizing sensitivity to the Ni gamma rays from Psyche. The Psyche mission approached this potential Ni background issue with two methods, locating the GRS away from the spacecraft/source of Ni and setting a threshold requirement against the total Ni mass of the spacecraft. Verifying that the total amount of Ni on the spacecraft is within this threshold is thus a key part of ensuring the GRS can meet its science objectives. Ni alloys are commonly used on spacecraft, but the mass and location of elemental Ni is not typically accounted for. Ni can be found in many materials all over the spacecraft – in fasteners, optical assemblies, magnetic shields, electromagnetic interference (EMI) tape, under gold plating, in connectors, and so on. The task proved further challenging because of the distributed nature of the build of this spacecraft and the use of vendors external to JPL. While the analysis was atypical and source information difficult to cull, the approach described in this paper used tools and data available to the project in some form to achieve this goal. For Psyche, current analysis shows there is margin in meeting the Ni mass requirement. This paper explains the systematic approach used to accurately and precisely record Ni content on the Psyche spacecraft. While this approach was defined for Ni on the Psyche mission, it can be used for any future project with the need to accurately estimate the total mass of a single element or material on a spacecraft.

Cullinan, Joe↗
NASA NTRS2022

Nickel Accounting for the Psyche Spacecraft

(16) Psyche is a metallic asteroid located in the asteroid belt between Mars and Jupiter. The composition of Psyche is unknown, but the scientific community believes it is composed primarily of iron, nickel, and silicates. The Psyche mission will be the first space mission to study this asteroid in close proximity, and as such, determining the elemental composition of the asteroid is one of the primary objectives of this mission. The spacecraft measures this elemental composition using the Gamma Ray Spectrometer (GRS), which detects cosmic-ray induced gamma rays from Psyche’s surface. In addition to gamma rays from Psyche, the GRS will also detect background gamma rays from spacecraft material nearby the GRS. Because Ni is such a key element for achieving the mission science objectives, a special effort has been made to minimize background gamma rays from Ni, thus maximizing sensitivity to the Ni gamma rays from Psyche. The Psyche mission approached this potential Ni background issue with two methods, locating the GRS away from the spacecraft/source of Ni and setting a threshold requirement against the total Ni mass of the spacecraft. Verifying that the total amount of Ni on the spacecraft is within this threshold is thus a key part of ensuring the GRS can meet its science objectives. Ni alloys are commonly used on spacecraft, but the mass and location of elemental Ni is not typically accounted for. Ni can be found in many materials all over the spacecraft – in fasteners, optical assemblies, magnetic shields, electromagnetic interference (EMI) tape, under gold plating, in connectors, and so on. The task proved further challenging because of the distributed nature of the build of this spacecraft and the use of vendors external to JPL. While the analysis was atypical and source information difficult to cull, the approach described in this paper used tools and data available to the project in some form to achieve this goal. For Psyche, current analysis shows there is margin in meeting the Ni mass requirement. This paper explains the systematic approach used to accurately and precisely record Ni content on the Psyche spacecraft. While this approach was defined for Ni on the Psyche mission, it can be used for any future project with the need to accurately estimate the total mass of a single element or material on a spacecraft.

Cullinan, Joe↗
NASA NTRSDate not supplied

Momentum Management Strategies for Solar Cruiser and Beyond (ISSS 2023)

Solar Cruiser is a small (ESPA-class) satellite Technology Demonstration Mission (TDM) to mature solar sail propulsion technology using a solar sail larger than 1600 square meters, demonstrating performance both as a propulsion system and a stable pointing platform for science observations in an artificial halo orbit sunward of the Sun-Earth Lagrange Point 1 (sub-L1). To ensure attitude control throughout the mission, momentum accumulated on the reaction wheels (RWs) used for attitude control must be managed such that the sailcraft does not lose control due to RW momentum saturation. Momentum builds up on the wheels from environmental disturbance torques caused by solar radiation pressure combined with a center of mass (CM)/center of pressure (CP) offset, deformed sail shape, and an off-sun pointing angle, plus other factors. Solar Cruiser mitigates this momentum build up by utilizing an Active Mass Translator (AMT) that maintains pitch and yaw momentum by trimming the CM/CP offsets, and thrusters to maintain roll momentum. A survey was conducted by the Solar Cruiser team to assess the feasibility and tradeoffs of novel momentum management concepts such as Reflectivity Control Devices (RCD’s), different thruster configurations, and control vanes and other articulated control surfaces. In addition, techniques to reduce disturbance torque buildup, such as reducing boom tip deflections and clock angle control, were assessed. Similar sailcraft momentum management strategies can be used for future missions such as space weather monitoring and Earth magnetotail science missions

Solar Sail↗
NASA NTRS2009

Roadmaps and Strategies for Crop Research for Bioregenerative Life Support Systems A Compilation of Findings from NASA’s Advanced Life Support Meetings

Extensive testing with plants for bioregenerative life support systems has been conducted by NASA for nearly 40 years, both through university grants and work at NASA field centers. During this time, numerous meetings were held to develop strategies and roadmaps for implementing bioregenerative life support systems. Findings from several of these meetings are summarized in this report. In nearly all cases, the recommendations included an active ground-based research program and integration tests with other life support subsystems, followed by eventual spaceflight testing. The most recent roadmap of NASA’s Exploration Life Support Crop Element suggests a sequence of first developing a modular vegetable production unit (VPU) to provide perishable foods to supplement the crew’s diet. A similar system could then be used on the lunar surface, with additional modules added as the lunar outpost expands. Eventually, these modules could be transferred to a dedicated pressurized logistics module (PLM) for crop production. Experience from the lunar tests could then be used to conduct a similar buildup for Mars missions, where in situ food production and bioregeneration would be important for achieving outpost autonomy. To date, most trade studies of bioregenerative life support systems indicate that reducing the costs associated with crop lighting systems are key, and use of light-emitting diodes (LEDs) or direct solar lighting offers promising options. Likewise, sustaining high yields and high harvest index (% edible biomass) will be important for minimizing costs, and this can be achieved by optimizing growth environments and through selecting, breeding, and genetically engineering crops suitable for space environments. Collectively, these strategies and roadmaps suggest that a combined approach of fundamental research, hardware (plant chamber) development, and operational testing is required to achieve reliable bioregenerative life support systems.

Bioregenerative↗
DOE OSTI2019

Recent development on nitrogen infusion work towards high Q and high gradient

A quality factor as high as 2 × 1010 at 1.5 GHz was achieved at a gradient of 35 MV/m by 800 °C annealing and N-infusion at 140 °C. A comparison of the field dependence of the surface resistance after N-infusion with a recent theoretical model that extends the calculation of the BCS surface resistance to high rf fields suggests an increase in the quasiparticles¿ relaxation time with increasing infusion temperature, which could be due to a decreasing density of subgap states. Nb coupons treated similarly showed the formation of thicker oxynitride layer on the surface beneath thin dielectric Nb2O5 layer. A plausible explanation for the improved Q0 is that the oxynitride layer on the Nb surface adds additional electron scattering within RF penetration depth.

Dhakal, P.↗
DOE OSTI2022

Forecasting ground-based sensitivity to the Rayleigh scattering of the CMB in the presence of astrophysical foregrounds

The Rayleigh scattering of cosmic microwave background (CMB) photons off the neutral hydrogen produced during recombination effectively creates an additional scattering surface after recombination that encodes new cosmological information, including the expansion and ionization history of the universe. A first detection of Rayleigh scattering is a tantalizing target for next-generation CMB experiments. We have developed a Rayleigh scattering forecasting pipeline that includes instrumental effects, atmospheric noise, and astrophysical foregrounds (e.g., Galactic dust, cosmic infrared background, or CIB, and the thermal Sunyaev-Zel'dovich effect). We forecast the Rayleigh scattering detection significance for several upcoming ground-based experiments, including SPT-3G+, Simons Observatory, CCAT-prime, and CMB-S4, and examine the limitations from atmospheric and astrophysical foregrounds as well as potential mitigation strategies. When combined with Planck data, we estimate that the ground-based experiments will detect Rayleigh scattering with a significance between 1.6 and 3.7, primarily limited by atmospheric noise and the CIB.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Coming Closer to High Frequency Gravitational Wave Detection With MAGO

In the last years, low frequency gravitational waves (GWs) have been consistently measured by the LIGOVirgo collaboration, but little to no attention has been paid to higher frequencies GWs in the range of 10 kHz to 100 MHz, at which confirmation for current theories or even new physics could be hidden. The MAGO 2.0 project aims at filling this gap in the parameter space using superconducting radio-frequency (SRF) cavities. Exploiting the excellent Q-factors of these resonators, we plan to detect tiny harmonic deformations induced by GWs which change the boundary conditions of the oscillating electromagnetic field. We present the results of the first cold tests ran at DESY and FNAL using the cavity prototype built 20 years ago at the end of the MAGO collaboration, characterizing the RF spectrum, Q-factor and surface resistance. Additionally we introduce the mechanical vibration spectrum characterization and the RF response of the cavity with the injection of a “fake GW” signal using piezoelectric actuators.

Marconato, Giovanni [Hamburg U.]↗
DOE OSTI2022

Hydrodynamics of countercurrent flow in an additive-manufactured column with triply periodic minimal surfaces for carbon dioxide capture

Computational investigation of the countercurrent flows in an additively manufactured (AM) column packed with triply periodic minimal surface (TPMS) is challenging. Multiphase flow simulations using the volume of fluid (VOF) method can explain the column’s hydrodynamic characteristics, including interfacial area, liquid holdup, pressure drop, flow regime, etc. The interfacial area is a key factor dictating the mass transfer via the absorption process, and thereby the overall efficiency of the column. The impacts of a solvent's physical properties, liquid and gas loads, and contact angle on the hydrodynamics are extensively explored. The solvents include traditional solvent (monoethanolamine [MEA]) used in industry as well as a water-lean solvent (EEMPA) as prospective solvents for carbon capture. As expected, interfacial area and liquid holdup increase with increasing liquid loads (q L ). The EEMPA exhibits higher values for the interfacial area and liquid holdup compared to those for the MEA. The dry and wet pressure drops per unit length in the column at different gas loads (F G ) are calculated and further compared with the empirical correlations for traditional packings. At low gas loads, i.e., in the preloading regime, the predicted values of the wet and dry pressure drops match well with the corresponding values calculated from available correlations. The gas load has a marginal impact on the interfacial area at its lower value, but the higher value of F G (>2.18 $\sqrt{Pa}$) causes flooding in the column. The effect of varying contact angles on the interfacial area and liquid holdup in the preloading regime is also studied. Both interfacial area and liquid holdup decrease with the increase in the value of the contact angle. Altogether, the effect of the contact angle on interfacial area is more pronounced than other parameters influencing the interfacial area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1975

Theoretical effect of modifications to the upper surface of two NACA airfoils using smooth polynomial additional thickness distributions which emphasize leading edge profile and which vary quadratically at the trailing edge

An investigation was conducted on a CDC 7600 digital computer to determine the effects of additional thickness distributions to the upper surface of the NACA 64-206 and 64 sub 1 - 212 airfoils. The additional thickness distribution had the form of a continuous mathematical function which disappears at both the leading edge and the trailing edge. The function behaves as a polynomial of order epsilon sub 1 at the leading edge, and a polynomial of order epsilon sub 2 at the trailing edge. Epsilon sub 2 is a constant and epsilon sub 1 is varied over a range of practical interest. The magnitude of the additional thickness, y, is a second input parameter, and the effect of varying epsilon sub 1 and y on the aerodynamic performance of the airfoil was investigated. Results were obtained at a Mach number of 0.2 with an angle-of-attack of 6 degrees on the basic airfoils, and all calculations employ the full potential flow equations for two dimensional flow. The relaxation method of Jameson was employed for solution of the potential flow equations.

Merz, A. W.↗
DOE OSTI2022

Electron beam surface remelting enhanced corrosion resistance of additively manufactured Ti-6Al-4V as a potential in-situ re-finishing technique

This study explores the effect of surface re-finishing on the corrosion behavior of electron beam manufactured (EBM) Ti-G5 (Ti-6Al-4V), including the novel application of an electron beam surface remelting (EBSR) technique. Specifically, the relationship between material surface roughness and corrosion resistance was examined. Surface roughness was tested in the as-printed (AP), mechanically polished (MP), and EBSR states and compared to wrought (WR) counterparts. Electrochemical measurements were performed in chloride-containing media. It was observed that surface roughness, rather than differences in the underlying microstructure, played a more significant role in the general corrosion resistance in the environment explored here. While both MP and EBSR methods reduced surface roughness and enhanced corrosion resistance, mechanical polishing has many known limitations. The EBSR process explored herein demonstrated positive preliminary results. The surface roughness (R a ) of the EBM-AP material was considerably reduced by 82%. Additionally, the measured corrosion current density in 0.6 M NaCl for the EBSR sample is 0.05 µA cm –2 , five times less than the value obtained for the EBM-AP specimen (0.26 µA cm –2 ).

42 ENGINEERING↗
DOE OSTI2024

Development of Surface Treatment Solutions for Stamping Tools Fabricated via Additive Manufacturing

Oak Ridge National Laboratory (ORNL) and H.E.F. USA, Inc. (HEF) partnered to develop wear resistant surface treatment of additive manufactured steels for stamping die applications under CRADA agreement NFE-19-07909. This project aimed at evaluating the ARCOR® process, developed by HEF, to improve the surface behavior of 410SS (stainless steel), 410NiMo SS, 630 SS, and Maraging 250 steel coupons and demo components, fabricated via wire arc additive manufacturing (WAAM), with and without post print heat treatment. The peak hardness achieved was ~1000 HV and above (Up to 1300 HV) for all materials under proper processing parameters, and far exceeded the target hardness of 746 HV (60 HRC). Finally, stamping tools were printed and nitrocarburized with the optimum parameters, and then went through 500 fabrication cycles. Characterization of the used 17-4PH stamping tool discovered no crack or delamination in the nitrocarburized layer and the interface between the nitrocarburized layer and substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2024

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 10 3 to 10 8 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed ‘melt pools’, were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Thermal conductance of augmented pressed metallic contacts at liquid helium temperatures

The thermal conductance of uncoated oxygen-free high conductivity (OFHC) copper, 6061-T6 aluminum, free-machining brass, and 304 stainless steel sample pairs which were augmented with a gold coated 6061-T6 aluminum washer inserted between the contact surfaces was measured over the temperature range of 1.6 to 6.0 K, with applied forces from 22 to 670 N. The contact surfaces of the sample pairs were prepared with a 0.8 micron lapped finish, while the finish of the aluminum washer was 0.2 micron lapped. The contribution to the overall thermal impedance by the bulk conductance of the aluminum washer was negligible. It was found that addition of the washer offered no significant conductance improvement over an uncoated single contact pair; any benefits from using the gold plated washer were counteracted by the addition of two more contact surfaces. Additionally, the thermal conductance of a 'combination' aluminum sample pair having one gold coated and one uncoated surface was measured and compared to the washer pair. The ratio of the conductance of the washer pair to half the conductance of the 'combination' pair was found to be constant and near unity over the temperature range of the data obtained, within experimental error.

Salerno, L. J.↗
DOE OSTI2020

Parametrically designed surface topography on CAD models of additively manufactured lattice structures for improved design validation

Additively Manufactured (AM) lattice structures of the laser powder bed fusion (LPBF) process generally have different surface geometries depending on the overhang angle and location. This means that the design validation stage is often challenging, considering it is based on an ideal Computer Aided Design (CAD) model that is not truly representative, since the AM part will be different in terms of dimensional accuracy and surface finish. Previous studies have relied on the design of surface textures that are independent of the overhang angle, or techniques based on directly using X-ray Computed Tomography (XCT) data. In this paper, a new technique for designing surface texture on the CAD of lattices has been investigated and correlated with areal surface roughness parameters. After extracting areal surface parameters from the XCT data of the lattice, the method allowed for the design of this surface texture on the part CAD taking in consideration if its up skin or down skin, without using XCT data as the main input. By applying this method, it is possible to obtain a lattice CAD model with a designed surface texture and geometry that is more representative of the actual AM lattice. The mean deviation between the CAD model with the designed surface and the XCT was a third of the one between the XCT and the initial CAD. The proposed method allows for designing and replicating LPBF AM surfaces on the CAD of a lattice, taking into consideration the dimensional deviation caused by AM surfaces, especially on overhangs. Assuming that an LPBF AM process is stable and produces approximately the same AM surface, this method can be used to predict the geometry of a lattice, providing a cost-effective and efficient methodology that minimizes the time needed for design validation.

42 ENGINEERING↗
NASA NTRS1975

Computational procedure for three-dimensional boundary layers on aircraft and aerospace vehicles

An implicit numerical procedure is developed to solve the full three-dimensional laminar, boundary layer equations over realistic aircraft and spacecraft configurations. This procedure utilizes splined functions in the direction normal to the surface and finite differences in the cross flow direction. Calculation of off-pitch plane attachment and detachment lines can be calculated. The solution procedure permits the incorporation of a wide variety of turbulent models and boundary conditions including; entropy layer procedures, specified surface temperatures or heat flux distributions, surface catalysis, mass addition, and the coupling to both three-dimensional inviscid codes and surface ablation codes. In addition, reasonable computing times are obtained.

Kendall, R. M.↗
NASA NTRS1980

Polyvinyl pyridine microspheres

Microspheres are produced by cobalt gamma radiation initiated polymerization of a dilute aqueous vinyl pyridine solution. Addition of cross-linking agent provides higher surface area beads. Addition of monomers such as hydroxyethylmethacrylate acrylamide or methacrylamide increases hydrophilic properties and surface area of the beads. High surface area catalytic supports are formed in the presence of controlled pore glass substrate.

Rembaum, Alan↗