Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Blended Wing Body (BWB) Boundary Layer Ingestion (BLI) Inlet Configuration and System Studies

A study was conducted to determine the potential reduction in fuel burned for BLI (boundary layer ingestion) inlets on a BWB (blended wing body) airplane employing AFC (active flow control). The BWB is a revolutionary type airplane configuration with engines on the aft upper surface where thick boundary layer offers the greatest opportunity for ram drag reduction. AFC is an emerging technology for boundary layer control. Several BLI inlet configurations were analyzed in the NASA-developed RANS Overflow CFD code. The study determined that, while large reductions in ram drag result from BLI, lower inlet pressure recovery produces engine performance penalties that largely offset this ram drag reduction. AFC could, however, enable a short BLI inlet that allows surface mounting of the engine which, when coupled with a short diffuser, would significantly reduce drag and weight for a potential 10% reduction in fuel burned. Continuing studies are therefore recommended to achieve this reduction in fuel burned considering the use of more modest amounts of BLI coupled with both AFC and PFC (Passive Flow Control) to produce a fail-operational system.

Kawai, Ronald T.↗
NASA NTRS1987

Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 2: Data compilation

A flight test program was performed using the Boeing 757 flight research airplane to investigate the effect of noise from wing mounted engines on laminar boundary layer transition. An NLF glove was installed on the right wing panel just outboard of the engine. The extent of laminar flow on the glove was measured as a function of engine power setting for a range of flight conditions. A combination of surface and probe microphones was distributed over the upper and lower wing surfaces to measure sound spectra. The flight test program was completed in June 1985 and the results of preliminary analysis indicate that a maximum of about 29 percent of chord laminar flow was obtained on the upper surface and about 28 percent on the lower surface (at a high sideslip condition). The engine speed was varied from about 2600 (idle) to about 4500 (maximum continuous power) r/min. This produced changes in sound pressure level up to 20 dB on the lower surface. On the upper surface, the noise levels were independent of engine power but sensitive to airplane Mach number. No effect of engine power setting on upper surface transition location was observed, and only a small forward movement of the transition location on the lower surface was observed at the high power settings. Volume 1 of this report contains the program description and data analysis. Volume 2 is a compilation of all of the flight test data.

Source record↗
DOE OSTI2018

Engineering the S-Layer of Caulobacter crescentus as a Foundation for Stable, High-Density, 2D Living Materials

Materials synthesized by organisms, such as bones and wood, combine the ability to self-repair with remarkable mechanical properties. This multifunctionality arises from the presence of living cells within the material and hierarchical assembly of different components across nanometer to micron scales. While creating engineered analogs of these natural materials is of growing interest, our ability to hierarchically order materials using living cells largely relies on engineered 1D protein filaments. Here, we lay the foundations for bottom-up assembly of engineered living material composites in 2D along the cell body using a synthetic biology approach. We engineer the paracrystalline surface-layer (S-layer) of Caulobacter crescentus to display SpyTag peptides that form irreversible isopeptide bonds to SpyCatcher-modified proteins, nanocrystals, and biopolymers on the extracellular surface. Using flow cytometry and confocal microscopy, we show that attachment of these materials to the cell surface is uniform, specific, and covalent, and its density can be controlled based on the location of the insertion within the S-layer protein, RsaA. Furthermore, we leverage the irreversible nature of this attachment to demonstrate via SDS-PAGE that the engineered S-layer can display a high density of materials, reaching 1 attachment site per 288 nm 2 . Lastly, we show that ligation of quantum dots to the cell surface does not impair cell viability and this composite material remains intact over a period of two weeks. Taken together, this work provides a platform for self-organization of soft and hard nanomaterials on a cell surface with precise control over 2D density, composition, and stability of the resulting composite, and is a key step towards building hierarchically-ordered engineered living materials with emergent properties.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Topological Control of Triply Periodic Minimal Surfaces for Thermal Design and Advanced Manufacturing: A Gyroid Case Study

Recently, there has been a heightened interest in using triply periodic minimal surfaces (TPMSs) in the design of compact process engineering components. The benefits of high surface area per unit volume, modular form, and inherent periodicity provide a holistic self-supporting network and flow-conducive features. Applications of importance include thermal power management, biomimetic scaffolds and structures, and feasibility of advanced manufacturing. This study presents a novel approach to the manipulation of the characteristic Schwarz-G, or gyroid TPMS, for thermal design in the context of advanced manufacturing. The study presents relationships between design parameters and resulting surface area as a target response using the characteristic equation of a gyroid. Through parametric control, the characteristic equation is manipulated to produce a 20-fold increase in achievable area over a baseline design characteristic of 25.4 mm through controlled combinations of design parameters. A second relationship is presented as a function of the maximum area achieved and manipulated design parameters. Through the analysis, the study presents a framework to identify and maximize the achievable area of TPMSs for advanced manufacturing and thermal management applications.

gyroid↗
NASA NTRS1973

Advanced control concepts

The selection of a trim solution that provides the space shuttle with the highest level of performance and dynamic control in the presense of wind disturbances and bias torques due to misalignment of rocket engines is described. It was determined that engine gimballing is insufficient to provide control to trim the vehicle for headwind and sidewind disturbances, and that it is necessary to use aerodynamic surfaces in conjunction with engine gimballing to achieve trim. The algebraic equations for computing the trim solution were derived from the differential equations describing the motion of the vehicle by substituting the desired trim conditions. The general problem of showing how the trim equations are derived from the equations of motion and the mathematical forms of the performance criterion is discussed in detail, along with the general equations for studying the dynamic response of the trim solution.

Hutton, M. F.↗
NASA NTRS1975

Static tests of a simulated upper surface blown jet-flap configuration utilizing a full-size turbofan engine

The investigation utilizing a small turbofan engine was conducted to evaluate static turning performance and pressure and temperature environment of an upper surface blown wing and flap segment. The tests involved modifications of the engine primary nozzle to alleviate high-temperature problems on the wing and flaps without adversely affecting static turning performance over the desired range of flap deflection and thrust condition.

Shivers, J. P.↗
NASA NTRS1983

The quiet short-haul research aircraft

The design concepts, performance capabilities, and projected applications of the Quiet Short-Haul Research Aircraft (QSRA) are discussed. The propulsive lift system of the QSRA provides the lift required for short field operations at low community noise levels. This system consists of four high bipass ratio, geared turbofan engines mounted so that the engine exhaust flows across the upper surface of the wing (upper surface blowing). Large specially shaped flaps behind each engine control the direction of the flow for each phase of flight. A 95 passenger short haul transport based on this technology could operate out of a 2500 foot runway with a combined takeoff and landing 90 EPNdB footprint area of 2.7 sq mi.

Cochrane, J. A.↗
NASA NTRS1984

Bending fatigue of electron-beam-welded foils. Application to a hydrodynamic air bearing in the Chrysler/DOE upgraded automotive gas tubine engine

A hydrodynamic air bearing with a compliment surface is used in the gas generator of an upgraded automotive gas turbine engine. In the prototype design, the compliant surface is a thin foil spot welded at one end to the bearing cartridge. During operation, the foil failed along the line of spot welds which acted as a series of stress concentrators. Because of its higher degree of geometric uniformity, electron beam welding of the foil was selected as an alternative to spot welding. Room temperature bending fatigue tests were conducted to determine the fatigue resistance of the electron beam welded foils. Equations were determined relating cycles to crack initiation and cycles to failure to nominal total strain range. A scaling procedure is presented for estimating the reduction in cyclic life when the foil is at its normal operating temperature of 260 C (500 F).

Saltsman, J. F.↗
DOE OSTI2021

Chiral Topological Surface States on a Finite Square Photonic Crystal Bounded by Air

Chiral, topologically protected, photonic surface states can be found at the boundary between gyrotropic photonic crystals where a changing magnetic field induces different topology across the interface. Typically, photonic crystals with either a suitable band structure on both sides of the interface to provide a band gap and evanescent decay of the surface states away from the interface, or an outer layer with engineered material properties is required. In this paper, we show the emergence of topological, unidirectional surface states at the termination of finite gyrotropic photonic crystals with a simple square lattice and C 4 rotational symmetry bounded by a vacuum, eliminating the need for an outside layer to enable chiral surface modes. Here, we start from an infinite, time-reversal-symmetry-breaking photonic crystal with a band gap associated with bands with nonzero Chern numbers, different from all-zero Chern numbers in air. We then modify the photonic crystal to move this band gap below the light line, while maintaining the Chern-number discontinuities. Band-structure calculations for a supercell approximating a photonic crystal finite in the direction normal to the surface demonstrate the existence, dispersion, and chirality of the surface mode. Extensive direct scattering calculations for a point source and spatial Fourier analysis further reveal a unidirectional free-space topological surface state, which propagates counterclockwise around the surface of a finite photonic crystal, providing a nearly foolproof way to cross-check the surface-mode band structure unaffected by backscattering from local defects. Additionally, scattering simulations allow an independent characterization of the state dispersion and unveil the robustness of the topological plasmonic mode propagation around the 90° bends of the structure, being due to only radiation leakage. In contrast to buried topological surface states, the observed surface modes at the photonic crystal–air interface have the advantage of being accessible to the outside world, allowing one to take advantage of the defect-tolerant backscattering-free surface modes to engineer emission from photonic crystal surfaces into arbitrary free-space beam shapes and directions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2012

Flow Simulation of N2B Hybrid Wing Body Configuration

The N2B hybrid wing body aircraft was conceptually designed to meet environmental and performance goals for the N+2 generation transport set by the subsonic fixed wing project. In this study, flow fields around the N2B configuration is simulated using a Reynolds-averaged Navier-Stokes flow solver using unstructured meshes. Boundary conditions at engine fan face and nozzle exhaust planes are provided by response surfaces of the NPSS thermodynamic engine cycle model. The present flow simulations reveal challenging design issues arising from boundary layer ingestion offset inlet and nacelle-airframe interference. The N2B configuration can be a good test bed for application of multidisciplinary design optimization technology.

Kim, Hyoungjin↗
NASA NTRS2013

Multiphase Modeling of Water Injection on Flame Deflector

This paper describes the use of an Eulerian Dispersed Phase (EDP) model to simulate the water injected from the flame deflector and its interaction with supersonic rocket exhaust from a proposed Space Launch System (SLS) vehicle. The Eulerian formulation, as part of the multi-phase framework, is described. The simulations show that water cooling is only effective over the region under the liquid engines. Likewise, the water injection provides only minor effects over the surface area under the solid engines.

Vu, Bruce T.↗
NASA NTRS2017

Long-Lived In-Situ Solar System Explorer (LLISSE)

Venus, while having similar size, mass, and location in the solar system to Earth, varies from Earth in many ways. The differences include its climate, atmosphere, and surface conditions. Surface conditions present formidable engineering challenges due to the high temperature and pressure. To date, landed missions have not been able to last more than about 2 hours on the surface [1]. This has resulted in significant knowledge gaps about the surface conditions of this important body in the solar system. The science community has effectively no in-situ temporal data on Venus surface conditions (temperature, pressure, winds and chemistry). These data are critical for the development of a thorough understanding of Venus' weather and the processes by which chemical species interact with each other, and are transported throughout the atmospheric column. This will help understand aspects of the atmosphere/planet interactions such as momentum exchange. To date, no capability has been available to enable a long lived surface probe to make these kinds of measurements. However, recently developed Silicon Carbide based electronics, sensors, and other technologies have matured to a state where a simple, but powerful long-life scientific probe would be feasible for Venus. It is now possible to directly qualify the durability and functionality of these components in a simulated Venus surface environment and demonstrate the ability to return valuable scientific data.

Probe↗
NASA NTRS1974

Small scale wind tunnel model investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A small-scale wind tunnel test of a two engine hybrid model with upper surface blowing on a simulated expandable duct internally blown flap was accomplished in a two phase program. The low wing Phase I model utilized 0.126c radius Jacobs/Hurkamp flaps and 0.337c radius Coanda flaps. The high wing Phase II model was utilized for continued studies on the Jacobs/Hurkamp flap. Principal study areas included: basic data both engines operative and with an engine out, control flap utilization, horizontal tail effectiveness, spoiler effectiveness, USB nacelle deflector study and USB/IBF pressure ratio effects.

Waites, W. L.↗
NASA NTRS1980

High temperature self-lubricating coatings for air lubricated foil bearings for the automotive gas turbine engine

coating combinations were developed for compliant surface bearings and journals to be used in an automotive gas turbine engine. The coatings were able to withstand the sliding start/stops during rotor liftoff and touchdown and occasional short time, high speed rubs under representative loading of the engine. Some dozen coating variations of CdO-graphite, Cr2O3 (by sputtering) and CaF2 (plasma sprayed) were identified. The coatings were optimized and they were examined for stoichiometry, metallurgical condition, and adhesion. Sputtered Cr2O3 was most adherent when optimum parameters were used and it was applied on an annealed (soft) substrate. Metallic binders and interlayers were used to improve the ductility and the adherence.

Bhushan, B.↗
NASA NTRS1974

Lunar soil properties and soil mechanics

The long-range objectives were to develop methods of experimentation and analysis for the determination of the physical properties and engineering behavior of lunar surface materials under in situ environmental conditions. Data for this purpose were obtained from on-site manned investigations, orbiting and softlanded spacecraft, and terrestrial simulation studies. Knowledge of lunar surface material properties are reported for the development of models for several types of lunar studies and for the investigation of lunar processes. The results have direct engineering application for manned missions to the moon.

Mitchell, J. K.↗
NASA NTRS1973

Electrostatic propulsion beam divergence effects on spacecraft surfaces, volume 2

The third phase of a program to develop understanding of and tolerance-level criteria for the deleterious effects of electrostatic rocket exhaust (Cs, Cs(+), Hg, Hg(+)) and materials of rocket construction impinging on typical classes of spacecraft (S/C) surfaces was completed. Models of ion engine effluents and models describing the degradation of S/C surfaces by these effluents are presented. Experimental data from previous phases are summarized and Phase 2 data and analysis are presented in detail. The spacecraft design implications of ion engine contaminants are discussed.

Hall, D. F.↗