HWO TMPO Status
Habitable Worlds Observatory (HWO) Technology Maturation Project Office (TMPO) Status
HAB↗
SEARCH · Search NASA
Results for “technology maturity”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Updating High-Order Aeroservoelastic Models from Low-Order System Identification Results
Estimating aircraft models from test data requires several simplifying assumptions that introduce biases into the parameter estimates. In this paper, these biases are defined and a method for estimating the biases is discussed. Having an estimate of the bias allows the parameters estimated from test to be integrated into a high-order model. The Integrated Adaptive Wing Technology Maturation (IAWTM) wind tunnel model is discussed and the bias is demonstrated for one of the testing configurations. The methodology was able to estimate these biases and apply corrections to high-order aeroelastic models to improve the fit to test data. The consideration of the biases allows more meaningful comparisons and avoids the erroneous differences between pretest predictions and the fitted model.
Jeffrey Ouellette↗
Hybrid Electric Turboprop Commercial Freighter Opportunity
As the era of electric and hybrid electric aviation is dawning, we have the opportunity to reduce cost, energy use, and emissions of air transportation. In this paper, the case is made for the potential efficiency benefits that can be gained with hybrid electric propulsion. Initial economic, mission profile, and propulsion system concepts for a large turboprop aircraft we designate as the Hybrid Electric Turboprop Commercial Freighter (HETCOF) are presented. Market analysis shows HETCOF has the potential to serve a large market share, but the cost requirements for a new purpose built are challenging relative to the repurposed narrow body aircraft currently operating in the market. Comparing HETCOF to a genericized large turboprop freighter the payload capacity is reduced by 40% for the TRL 5+ configuration but is equivalent to the baseline for the TRL 1-2 configuration. All HETCOF configurations result in increased efficiency and subsequent block fuel, block energy, and block emissions reductions. An integrated power/thermal/and energy storage system is presented and analyzed using key performance parameters to estimate weights and losses at three technology readiness levels. Analysis shows that for a concept like this to have economic and energy benefits, many TRL 1-2 level technologies would be needed. Relevant ARPA-E programs and NASA technologies being developed to enable the benefit are also described. The most significant result of this paper is that the HETCOF concept can close with reduced fuel burn, energy use, and emissions while retaining some or all of the cargo capability of the baseline aircraft across TRL level assumptions, which enables this platform to be used for near term introduction with increasing benefits as technology matures.
Ralph H Jansen↗
Updating High-Order Aeroservoelastic Models from Low-Order System Identification Results
Estimating aircraft models from test data requires several simplifying assumptions that introduce biases into the parameter estimates. In this paper, these biases are defined and a method for estimating the biases is discussed. Having an estimate of the bias allows the parameters estimated from test to be integrated into a high-order model. The Integrated Adaptive Wing Technology Maturation (IAWTM) wind tunnel model is discussed and the bias is demonstrated for one of the testing configurations. The methodology was able to estimate these biases and apply corrections to high-order aeroelastic models to improve the fit to test data. The consideration of the biases allows more meaningful comparisons and avoids the erroneous differences between pretest predictions and the fitted model.
Jeffrey Ouellette↗
HWO Technology Roadmapping - High Sensitivity UV and Visible Band Technologies for Instrumentation
We report on ongoing efforts by the HWO Project Office at NASA Goddard to define technology development roadmaps for a variety of technologies relevant to the astrophysics instruments on the mission. We have been soliciting input from a variety of subject matter experts (SMEs) to define the necessary development paths to achieve a TRL of 5 by 2029, the necessary cost and investment, and the schedule over which the work can be achieved. This planning is directed by the performance requirements coming out of the START science working group studies and will enable the Project Office to define the Observatory Technology Maturation Plan by Summer 2025.
Paul Scowen↗
Laser Beam Welding Advancements for In-Space Servicing, Assembly, and Manufacturing
NASA is currently working to develop in-space servicing, assembly, and manufacturing (ISAM) capabilities for low Earth orbit and the lunar surface. One crucial technology for this effort is laser beam welding. Laser systems can perform joining, cleaning, cutting, and repair activities, which will enable the construction of large in-space structures that could not fit on a single launch vehicle, such as trusses for solar panels, radiators, or communications infrastructure. Multiple projects studying laser welding for space applications are currently underway at NASA Marshall Space Flight Center. One of these, the DIsk-Shaped Configurable and Modular vAcuum uNit (DISCMAN), is a compact vacuum chamber designed to support parameter development for laser welding in microgravity. It contains a rotating platen with weld samples made from aluminum, steel, and titanium, a high-power infrared laser, and integrated pumps for pulling vacuum inside the sample cartridge. The DISCMAN payload is planned to launch to the International Space Station, where welds will be performed under sustained microgravity inside the Bishop Airlock. Another effort underway at Marshall is the Lunar Assembly and Servicing by Autonomous Robotics (LASAR) initiative. This project uses a space-rated robotic arm equipped with a laser weld head, wire feeder, and multiple cameras to perform welds in a thermal vacuum chamber simulating the lunar surface environment. Some of these welds are done on snowflake joints, which are specially designed to slot together to join segments of trussN structures, allowing for the construction of tall surface infrastructure. DISCMAN, LASAR, and other projects are being carried out to advance the technological maturity of in-space laser beam welding, collect data to inform computational models, and learn reliable processes for creating weld joints in space. This work supports NASA’s greater goals to expand humanity’s presence in low Earth orbit, establish a permanent moon base, and eventually send crewed missions to Mars and beyond.
Manufacturing↗
Laser Beam Welding Advancements for In-Space Servicing, Assembly, and Manufacturing
NASA is currently working to develop in-space servicing, assembly, and manufacturing (ISAM) capabilities for low Earth orbit and the lunar surface. One crucial technology for this effort is laser beam welding. Laser systems can perform joining, cleaning, cutting, and repair activities, which will enable the construction of large in-space structures that could not fit on a single launch vehicle, such as trusses for solar panels, radiators, or communications infrastructure. Multiple projects studying laser welding for space applications are currently underway at NASA Marshall Space Flight Center. One of these, the DIsk-Shaped Configurable and Modular vAcuum uNit (DISCMAN), is a compact vacuum chamber designed to support parameter development for laser welding in microgravity. It contains a rotating platen with weld samples made from aluminum, steel, and titanium, a high-power infrared laser, and integrated pumps for pulling vacuum inside the sample cartridge. The DISCMAN payload is planned to launch to the International Space Station, where welds will be performed under sustained microgravity inside the Bishop Airlock. Another effort underway at Marshall is the Lunar Assembly and Servicing by Autonomous Robotics (LASAR) initiative. This project uses a space-rated robotic arm equipped with a laser weld head, wire feeder, and multiple cameras to perform welds in a thermal vacuum chamber simulating the lunar surface environment. Some of these welds are done on snowflake joints, which are specially designed to slot together to join segments of trussN structures, allowing for the construction of tall surface infrastructure. DISCMAN, LASAR, and other projects are being carried out to advance the technological maturity of in-space laser beam welding, collect data to inform computational models, and learn reliable processes for creating weld joints in space. This work supports NASA’s greater goals to expand humanity’s presence in low Earth orbit, establish a permanent moon base, and eventually send crewed missions to Mars and beyond.
Robotics↗
Solvent-Based Absorption
Solvent-based CO2 absorption processes are the oldest and most mature technology, having been deployed at what would be considered full-scale for post-combustion CO2 capture. There are many commercial 1st and 2nd generation technologies such as Econamine FG+, CANSOLV, Oase Blue, KS-1, with dozens if not hundreds of 3rd generation solvents that are been studied at varying stages of testing. While there are many solvents that are under development, nearly all solvents function on the same physical and chemical principles and it is not surprising that they all have similar configurations with somewhat comparable levels of performance. The enhancements in energy efficiency for solvents have come primarily from the engineering advancements over many decades of refinement, though surprisingly little has changed with respect to the molecular structure of solvents over the same period of time. In this chapter, we explain the tenets of solvent-based processes and provide a chronological timeline of solvents throughout their nearly 90-year history with discussions of why and how advancements in solvent efficiency have been achieved and we conclude with an outlook for the future of solvents and their place in CCUS.
Heldebrant, David J.↗
Functional and Operating Requirements for the Microreactor Agile Non-Nuclear Experimental Test Bed (MAGNET)
Microreactors, or small, transportable reactors with a capacity of < 20 MWTH, are sought to provide heat and power for myriad applications in remote areas, military installations, emergency operations, humanitarian missions and disaster relief zones as illustrated in Figure 1. These small, transportable reactor designs, while offering many advantages, are largely untested and unproven. System and component testing is needed to demonstrate to regulators that these designs are safe and to convince customers that the systems are robust, reliable, and efficient. The microreactor agile non-nuclear experimental test bed (MAGNET) is being constructed at Idaho National Laboratory to assist with the development, demonstration, and validation of microreactor components and systems. MAGNET will support technology maturation to reduce uncertainty and risk relative to the operation and deployment of this unique class of systems. Stakeholders for this test bed include microreactor developers, energy users, and regulators. Regulators will be engaged early in the design and testing to expedite regulatory approval and licensing. Within MAGNET, systems and components can be safely tested, providing valuable information on operating regimes, failure modes, and thresholds. Since there are various types of microreactors being proposed, which can be classified according to their core cooling method, heat-pipes, gas-cooled (pebble bed or prismatic), molten salt, light water, or light water, the goal is to provide a test bed that is broadly applicable to multiple microreactor concepts. Each reactor type poses a different set of design and operational challenges and performance claims stated by commercial vendors have not been independently verified through rigorous testing. The initial set of tests to be performed in MAGNET are targeted towards demonstrating the feasibility and performance of heat-pipe cooled reactors, since this concept is unique to very small nuclear reactors. However, the testbed will be constructed to accommodate other designs in addition to heat-pipe cooled reactors.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
MoorDyn V2: New Capabilities in Mooring System Components and Load Cases: Preprint
MoorDyn, an open-source mooring dynamics model, is being expanded with capabilities for additional mooring system features and load cases. As floating wind turbine technology matures, mooring systems are becoming more sophisticated and more complex scenarios need to be considered in the design process. Mooring systems may have synthetic line materials, ballast/buoyancy bodies along the lines, or interconnections between platforms. Failure modes may involve multiple cascading line failures that depend on mooring system dynamics. Features recently added to MoorDyn aim to address these emerging needs. MoorDyn’s linear elasticity model has been supplemented to support user-defined stress-strain curves, which can be adjusted to represent synthetic mooring materials. Rigid six-degree-of-freedom bodies in the mooring system can now be modeled using two new model objects. “Rod” objects provide an option for rigid cylindrical bodies. They use the existing Morison equation-based hydrodynamics model and can be connected to mooring lines at either end. “Body” objects provide a generic six-degree-of-freedom rigid-body representation based on a lumped-parameter model of translational and rotational properties. Rod objects can be added to Body objects and mooring lines can be attached at any location, allowing a wide variety of submerged structures to be integrated into the mooring system. Lastly, a means of dynamically simulating mooring line failures has been implemented. These new features, currently in the C++ version of MoorDyn, are described and then demonstrated on a two-turbine shared-mooring array. A qualitative view of the results suggests the new features are functioning as expected.
49 EE - Wind and Water Power Program - Wind (EE-4W↗
Individual Wave Detection and Tracking within a Rotating Detonation Engine through Computer Vision Object Detection applied to High-Speed Images
Known for their simplistic design and continuous detonation, rotating detonation engines (RDEs) constitute a majority of current pressure gain combustion (PGC) research efforts. Experimental RDE operation times have been continuously extended through the use of rig cooling techniques. As the window of observable behavior is expanded, and as the technology matures toward eventual integration within gas turbines, monitoring techniques must evolve to better match industrial diagnostics. High-speed image analysis techniques prove useful to capture and evaluate the unsteady detonation behavior within the RDE. Traditional image analysis techniques, however, require extensive processing times which prohibit simultaneous monitoring. To better address this problem, a computer vision object detection methodology is proposed to quickly detect individual detonation waves within a single down-axis image. Detonation waves are detected in individual images by the implemented computer vision method You Only Look Once (YOLO) object detection network. In order to detect detonation waves, the network must first be trained using RDE images of interest, for which each required phase of network development is outlined. Detection of waves is improved through proper treatment of the collected image set, variation of Intersection over Union (IoU) and confidence thresholding, and through a parametric study of annotation dimensions. Each detected wave is described by its location and rotational direction, and locations are tracked to calculate wave velocity across each frame, leading to a timestep resolution of 20 µs. Wave velocities are also calculated through a series of frames, leading to a suitable average velocity estimation using as few as 10 frames. Uncertainty analysis accounting for variation in camera framerate, pixel width and annotation centroid locations estimates a total uncertainty of ±4.3% for velocity calculations, using the smallest annotation boxes. This method offers great reductions in processing times, as a step toward real-time monitoring of detonation waves within an RDE. Improving on previous studies, this technique is impartial to wave modes not included in the original training set and calculates wave velocities independent of high-speed pressure data. The ability to isolate waves within predicted bounding boxes will likely facilitate analysis of pixel intensity variation as an estimation of wave strength in future work.
Johnson, Kristyn↗
Fuel Design and Fabrication: TRISO Particle Fuel
Tristructural-isotropic (TRISO) particle fuel is an advanced, mature technology for nuclear energy generation. Inherent containment of radionuclides within the fuel obviates the need for expensive reactor containment buildings; however, this benefit comes at the cost of increased complexity in fabrication relative to other nuclear fuel forms. In addition, rigorous fuel characterization and quality control efforts are required to ensure that the credited radionuclide containment within the fuel is realized.
Helmreich, Grant↗
Advancing Catalytic Fast Pyrolysis Through Integrated Experimentation and Multi-Scale Computational Modeling
This webinar will highlight recent results from a multi-disciplinary research effort in which integrated reaction testing was coupled with particle- and reactor-scale computational modeling to advance catalytic fast pyrolysis (CFP) for the production of renewable hydrocarbon fuels. Data will be presented from a series of ex situ CFP experiments in which a fixed bed of Pt/TiO2 was utilized with co-fed H2 to upgrade woody biomass pyrolysis vapors. Further discussion will include the application of these data towards the development of (1) a multiscale simulation framework to de-couple apparent kinetics from both intraparticle and reactor-scale transport phenomena and (2) a finite element computational model to understand and predict thermal excursions during catalyst regeneration. Throughout the presentation, the speakers will emphasize synergistic outcomes derived from the collaborative approach and highlight ongoing research efforts to accelerate technology maturation.
29 ENERGY PLANNING, POLICY, AND ECONOMY↗
Design of a Test Article and Test Facility to Investigate Flow-Induced Vibration of a Helical Coil Steam Generator
NuScale Power LLC (NuScale) is developing a small modular reactor (SMR) with unique design features and arrangements that require testing to provide quality data for safety analysis codes and design validation, as well as for technology maturation. A multi-phase testing program is underway at NuScale to demonstrate that its unique helical coil steam generator design is not susceptible to flow-induced vibration during operation. The phases of the testing program include modal testing of individual tubes during test article fabrication and modal and flow testing after test article completion. NuScale has contracted SIET S.p.A. in Piacenza, Italy for the design and fabrication of the test article and test facility. In-fabrication testing was performed at the site of test article build in Cremosano, Italy. Modal testing and flow testing of the completed test article will be performed at SIET’s facilities in Piacenza. This paper discusses the design of the test article and test facility, including supporting systems, required to generate the quality data required to support NuScale’s comprehensive vibration assessment program as part of the overall licensing effort for NuScale’s first-of-a-kind small modular light water reactor.
Flow-induced vibration, helical coil, steam genera↗
ASME Code Rules and ASTM Standards Integration for Ceramic Composite Core Materials and Components 1
Fiber-reinforced ceramic matrix composites have many desirable properties for high-temperature nuclear applications, including excellent thermal and mechanical properties and reasonable to outstanding radiation resistance. Over the last 20 years, the use of ceramic composite materials has already expanded in many commercial nonnuclear industries as fabrication and application technologies mature. The new ASME design and construction rules under Section III, Subsection HH, Subpart B lay out the requirements and criteria for materials, design, machining and installation, inspection, examination, testing, and the marking procedure for ceramic composite core components, which is similar to the established graphite code under Section III, Subsection HH, Subpart A. Moreover, the general requirements listed in Section III, Subsection HA, Subpart B are also expanded to include ceramic composite materials. The code rules rely heavily on the development and publication of standards for composite specification, classification, and testing of mechanical, thermal, and other properties. These test methods are developed in the American Society for Testing and Materials Committee C28 on Advanced Ceramics with a current focus on ceramic composite tubes. Details of the composites code, design methodology, and similarities to the graphite code, as well as guidance for the development of specifications for ceramic composites for nuclear application and recent standard developments, are discussed. The next step is to "close the gap" to support licensing aspects by validating the code with benchmarking data.
Geringer, Josina↗
Roadmap for IES Modeling and Simulation Activities
Since inception of the DOE-NE Integrated Energy Systems (IES) program, several program and modeling visions and roadmaps have been published. In 2017, the last modeling and simulation capability development plan was published. In 2020, a comprehensive roadmap for the DOE-NE Integrated Energy Systems program has been published. The current report is meant to update the 2017 modeling and simulation capability roadmap and complement the IES overall program roadmap published in 2020. The role of modeling and simulation within IES is to support the demonstration of new coupled integrated technologies along every step of the technology maturation from the strategic analysis of preferred system architecture to preliminary design, to laboratory testing, up to full commercial testing and integration. To achieve this role, modeling and simulation must be able to assess the technical performance and the economic viability of potential IES. Also, modeling and simulation must provide support for experimental evaluations, i.e., support component design and real time operations of experimental demonstration systems. Finally, modeling and simulation can help scale-up experimental systems to the final commercial systems. This report details the current state of the modeling and simulation efforts within IES for the above-mentioned areas, provides a gap analysis and proposes next steps for a time horizon over the next 4 to 5 years.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Development of Non-Nuclear Microreactor Experimental Capability
Microreactors, or small, transportable reactors with a capacity of 20 MWTH or less, are sought to provide heat and power for myriad applications in remote areas, military installations, emergency operations, humanitarian missions, and disaster relief zones. These small, transportable reactor designs, while offering many advantages, are largely untested and unproven. A non-nuclear system and component testing capability is needed to demonstrate to regulators that these designs are safe and to convince customers that the systems are robust, reliable, and efficient. Idaho National Laboratory has constructed the microreactor agile non-nuclear experimental test bed (MAGNET) to assist with the development, demonstration, and validation of microreactor components and systems. MAGNET will support microreactor technology maturation to reduce uncertainty and risk relative to the operation and deployment of this unique class of systems. Stakeholders for this test bed include microreactor developers, energy users, and regulators. Regulators will be engaged early in the design and testing to expedite regulatory approval and licensing.
42 ENGINEERING↗
MRP: Design Rules for Refractory Metals
Presentation on Design rules for refractory metals to be given at the Joint ART Materials/AMMT Program Review at DOE Headquarters, Germantown, MD, June 5-8, 2023. Includes microreactor program work for structural materials, failure points of interest, technology, technology maturation and de-risk designs, refractory metals, plan for developing code case as prototype by advanced reactor developers which meets design requirements, and also provides ASME Section III rules.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗