Search NASA⌕ Search

SEARCH · Search NASA

Results for “variable load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Acoustic measurements of three Prop-Fan models

Results of NASA sponsored acoustic tests of three 2 ft. diameter models of the Prop-Fan (a small diameter, highly loaded, many-bladed variable pitch advanced turboprop) are presented. The highly swept model designed for noise reduction produces substantially less near field noise at simulated 0.8 Mach number cruise conditions than the unswept or slightly swept models. It also produces less far field noise at conditions simulating takeoff and landing. The noise reduction mechanism is discussed. Correlation between harmonic noise measurements and theoretical predictions and between measured and predicted acoustic pressure pulses is good. Shadowgraph measurements which show the location of blade associated wave patterns were obtained. Predicted and measured wave locations show good general agreement. Full scale near and far field noise is predicted.

Brooks, B. M.↗

Sensitivity analysis results of the effects of various parameters on composite design

Sensitivity analysis results are presented to assess the effects of a multitude of important parameters on fiber composite design and structural response. These results were obtained by using optimum design procedures in conjunction with sensitivity analyses. Sensitivity analyses were performed to assess the effects on composite optimum design and structural response of parameters such fiber transverse and shear properties, in situ matrix elastic and strength properties, correlation coefficients used in composite micromechanics and in combined strength predictions, processing variables, and perturbations of loading conditions. The results show that matrix properties, fiber volume ratio and small perturbations of the loading conditions have significant effects on certain composite structural responses. The remaining parameters have negligible effect.

Chamis, C. C.↗

Controller for a High-Power, Brushless dc Motor

Driving and braking torques controllable. Control circuit operates 7-kW, 45-lb-ft (61-N-m), three-phase, brushless dc motor in both motor and generator modes. In motor modes, energy from power source is pulse-width modulated to motor through modified "H-bridge" circuit, in generator mode, energy from motor is pulse-width modulated into bank of load resistors to provide variable braking torques. Circuit provides high-resolution torque control in both directions over wide range of speeds and torques. Tested successfully at bus voltages up to 200 Vdc and currents up to 45 A.

Fleming, David J.↗

Transonic airfoil design for helicopter rotor applications

Despite the fact that the flow over a rotor blade is strongly influenced by locally three-dimensional and unsteady effects, practical experience has always demonstrated that substantial improvements in the aerodynamic performance can be gained by improving the steady two-dimensional charateristics of the airfoil(s) employed. The two phenomena known to have great impact on the overall rotor performance are: (1) retreating blade stall with the associated large pressure drag, and (2) compressibility effects on the advancing blade leading to shock formation and the associated wave drag and boundary-layer separation losses. It was concluded that: optimization routines are a powerful tool for finding solutions to multiple design point problems; the optimization process must be guided by the judicious choice of geometric and aerodynamic constraints; optimization routines should be appropriately coupled to viscous, not inviscid, transonic flow solvers; hybrid design procedures in conjunction with optimization routines represent the most efficient approach for rotor airfroil design; unsteady effects resulting in the delay of lift and moment stall should be modeled using simple empirical relations; and inflight optimization of aerodynamic loads (e.g., use of variable rate blowing, flaps, etc.) can satisfy any number of requirements at design and off-design conditions.

Hassan, Ahmed A.↗

Stress and tectonics on Mars

Deformation of the Martian lithosphere and the various theoretical formulations used to model its behavior on local, regional, and global scales are studied. An overview of the various classes of tectonic features found on Mars is presented. The tectonic record on Mars, which provides the basic framework for interpreting theoretical thermomechanical models in terms of major tectonic events and provinces is summarized. The thickness of the elastic lithosphere is estimated using its response to local surface loads, and significant spatial variability is found, with values ranging from 20 to 300 km. A comparison of the major radial graben systems with theoretical stress models shows that more than one mechanism of lithospheric deformation is required to produce its enormous extent.

Banerdt, W. B.↗

A recurrence formula for shear-lag problems

The analysis of the bending action in box beams with appreciable shear deformation of the flanges becomes very difficult in the general case of variable cross section and loading. This paper presents a convenient method of solving the problem by the familiar method of dividing the beam into a number of bays that can be assumed to have constant cross section and loading. Application of formerly derived shear-lag formulas leads to a general equation closely analogous in form to the well-known three-moment equation. A numerical example and two comparisons between calculation and experimental results are included.

Kuhn, Paul↗

Experimental evaluation of shape memory alloy actuation technique in adaptive antenna design concepts

Creation of an antenna system that could autonomously adapt contours of reflecting surfaces to compensate for structural loads induced by a variable environment would maximize performance of space-based communication systems. Design of such a system requires the comprehensive development and integration of advanced actuator, sensor, and control technologies. As an initial step in this process, a test has been performed to assess the use of a shape memory alloy as a potential actuation technique. For this test, an existing, offset, cassegrain antenna system was retrofit with a subreflector equipped with shape memory alloy actuators for surface contour control. The impacts that the actuators had on both the subreflector contour and the antenna system patterns were measured. The results of this study indicate the potential for using shape memory alloy actuation techniques to adaptively control antenna performance; both variations in gain and beam steering capabilities were demonstrated. Future development effort is required to evolve this potential into a useful technology for satellite applications.

Kefauver, W. Neill↗

Test and Analysis of Composite Hat Stringer Pull-off Test Specimens

Hat stringer pull-off tests were performed to evaluate the delamination failure mechanisms in the flange region for a rod-reinforced hat stringer section. A special test fixture was used to pull the hat off the stringer while reacting the pull-off load through roller supports at both stringer flanges. Microscopic examinations of the failed specimens revealed that failure occurred at the ply termination in the flange area where the flange of the stiffener is built up by adding 45/-45 tape plies on the top surface. Test results indicated that the as-manufactured microstructure in the flange region has a strong influence on the delamination initiation and the associated pull-off loads. Finite element models were created for each specimen with a detailed mesh based on micrographs of the critical location. A fracture mechanics approach and a mixed mode delamination criterion were used to predict the onset of delamination and the pull-off load. By modeling the critical local details of each specimen from micrographs, the model was able to accurately predict the hat stringer pull-off loads and replicate the variability in the test results.

Li, Jian↗

Towards a Probabilistic Criterion for Preliminary Shell Design

Thin-walled stiffened or unstiffened, metallic or composite shells are widely used structural elements in aeronautical and space applications. Buckling strength, which is a major concern in all these areas, is affected by the uncertainties in the definition of loads, material properties, geometric variables, engineering models and the accuracy of the analysis tools used in the design phase. The NASA design criteria monographs from the late sixties account for these design uncertainties by the use of a lump sum safety factor or the so-called "knockdown" factor gamma, which usually results in an overly conservative design. In the present paper a new, reliability based, probabilistic design procedure for buckling critical imperfect isotropic shells is proposed. It essentially consists of a stochastic approach based on a new, improved "knockdown" factor lambda(sub a) that is not as conservative as the traditional one. It is felt that by quantifying and understanding the "problem uncertainties" such as initial imperfections and their influence on the design variables, one can develop a better engineered, better designed and safer system.

Arbocz, Johann↗

On the Accuracy of Probabilistic Bucking Load Prediction

The buckling strength of thin-walled stiffened or unstiffened, metallic or composite shells is of major concern in aeronautical and space applications. The difficulty to predict the behavior of axially compressed thin-walled cylindrical shells continues to worry design engineers as we enter the third millennium. Thanks to extensive research programs in the late sixties and early seventies and the contributions of many eminent scientists, it is known that buckling strength calculations are affected by the uncertainties in the definition of the parameters of the problem such as definition of loads, material properties, geometric variables, edge support conditions, and the accuracy of the engineering models and analysis tools used in the design phase. The NASA design criteria monographs from the late sixties account for these design uncertainties by the use of a lump sum safety factor. This so-called 'empirical knockdown factor gamma' usually results in overly conservative design. Recently new reliability based probabilistic design procedure for buckling critical imperfect shells have been proposed. It essentially consists of a stochastic approach which introduces an improved 'scientific knockdown factor lambda(sub a)', that is not as conservative as the traditional empirical one. In order to incorporate probabilistic methods into a High Fidelity Analysis Approach one must be able to assess the accuracy of the various steps that must be executed to complete a reliability calculation. In the present paper the effect of size of the experimental input sample on the predicted value of the scientific knockdown factor lambda(sub a) calculated by the First-Order, Second-Moment Method is investigated.

Arbocz, Johann↗

Wear Measurement System

Lewis Research Center developed a tribometer for in-house wear tests. Implant Sciences Corporation (ISC), working on a NASA contract to develop coatings to enhance the wear capabilities of materials, adapted the tribometer for its own use and developed a commercial line of user-friendly systems. The ISC-200 is a pin-on-disk type of tribometer, functioning like a record player and creating a wear groove on the disk, with variables of speed and load. The system can measure the coefficient of friction, the wear behavior between materials, and the integrity of thin films or coatings. Applications include measuring wear on contact lenses and engine parts and testing disk drives.

Source record↗

The Effects of Foam Thermal Protection System on the Damage Tolerance Characteristics of Composite Sandwich Structures for Launch Vehicles

For any structure composed of laminated composite materials, impact damage is one of the greatest risks and therefore most widely tested responses. Typically, impact damage testing and analysis assumes that a solid object comes into contact with the bare surface of the laminate (the outer ply). However, most launch vehicle structures will have a thermal protection system (TPS) covering the structure for the majority of its life. Thus, the impact response of the material with the TPS covering is the impact scenario of interest. In this study, laminates representative of the composite interstage structure for the Ares I launch vehicle were impact tested with and without the planned TPS covering, which consists of polyurethane foam. Response variables examined include maximum load of impact, damage size as detected by nondestructive evaluation techniques, and damage morphology and compression after impact strength. Results show that there is little difference between TPS covered and bare specimens, except the residual strength data is higher for TPS covered specimens.

Nettles, A. T.↗

Major Influence of Tropical Volcanic Eruptions on the Stratospheric Aerosol Layer During the Last Decade

The variability of stratospheric aerosol loading between 1985 and 2010 is explored with measurements from SAGE II, CALIPSO, GOMOS/ENVISAT, and OSIRIS/Odin space-based instruments. We find that, following the 1991 eruption of Mount Pinatubo, stratospheric aerosol levels increased by as much as two orders of magnitude and only reached background levels between 1998 and 2002. From 2002 onwards, a systematic increase has been reported by a number of investigators. Recently, the trend, based on ground-based lidar measurements, has been tentatively attributed to an increase of SO2 entering the stratosphere associated with coal burning in Southeast Asia. However, we demonstrate with these satellite measurements that the observed trend is mainly driven by a series of moderate but increasingly intense volcanic eruptions primarily at tropical latitudes. These events injected sulfur directly to altitudes between 18 and 20 km. The resulting aerosol particles are slowly lofted into the middle stratosphere by the Brewer-Dobson circulation and are eventually transported to higher latitudes.

Vernier, Jean-Paul↗

The Effects of Plasma Application on Radish Seeds with Implications for Space Crop Production

In extended space missions, the astronaut diet will consist mostly of prepackaged foods. This could result in nutritional deficiencies due to the gradual breakdown of certain vitamins. To address this deficiency, fresh produce must be grown from seed during spaceflight. Stored seeds, however, can be vulnerable to microbial contamination which could jeopardize plant health and crop food safety. To alleviate this concern, the current practice is to sanitize seeds on the ground before spaceflight to the International Space Station (ISS). Methods of seed sanitization include alcohol soaking and chlorine gas fumigation, which have harmful effects on the environment and human health. Plasma application is a new sanitization approach that avoids these negative side effects while potentially elevating germination rate and improving growth rate; yet plasma application requires specific exposure time, power, and pressure to achieve these benefits. In the present study, Raphanus sativus ‘Cherry Belle’ radish seeds were exposed to either low pressure (Diener) plasma or atmospheric pressure plasma for varying increments of time (30s-1200s). Data collected includes immediate germination rate (viability) and microbial log reduction. Additionally, seeds were stored for later germination rate testing. Microbial assay controls have highlighted variability in initial microbial load between individual seeds, and further work is being performed to determine the standard microbial load of an untreated seed. In some samples, a negative log reduction was observed after plasma treatment encouraging further study to determine if the plasma is perforating the seed coat and releasing endophytic microbes. Treatment with Diener plasma shows promising microbial log reduction, but lower viability. In contrast, treatment with atmospheric pressure plasma offers high viability, but poor microbial log reduction. Further study will aim at determining whether plasma treatment is effective at not only sanitization, but sterilization. This research was funded by a NASA grant at the Kennedy Space Center.

Plasma↗

The Effects of Plasma Application on Radish Seeds with Implications for Space Crop Production

In extended space missions, the astronaut diet will consist mostly of prepackaged foods. This could result in nutritional deficiencies due to the gradual breakdown of certain vitamins. To address this deficiency, fresh produce must be grown from seed during spaceflight. Stored seeds, however, can be vulnerable to microbial contamination which could jeopardize plant health and crop food safety. To alleviate this concern, the current practice is to sanitize seeds on the ground before spaceflight to the International Space Station (ISS). Methods of seed sanitization include alcohol soaking and chlorine gas fumigation, which have harmful effects on the environment and human health. Plasma application is a new sanitization approach that avoids these negative side effects while potentially elevating germination rate and improving growth rate; yet plasma application requires specific exposure time, power, and pressure to achieve these benefits. In the present study, Raphanus sativus ‘Cherry Belle’ radish seeds were exposed to either low pressure (Diener) plasma or atmospheric pressure plasma for varying increments of time (30s-1200s). Data collected includes immediate germination rate (viability) and microbial log reduction. Additionally, seeds were stored for later germination rate testing. Microbial assay controls have highlighted variability in initial microbial load between individual seeds, and further work is being performed to determine the standard microbial load of an untreated seed. In some samples, a negative log reduction was observed after plasma treatment encouraging further study to determine if the plasma is perforating the seed coat and releasing endophytic microbes. Treatment with Diener plasma shows promising microbial log reduction, but lower viability. In contrast, treatment with atmospheric pressure plasma offers high viability, but poor microbial log reduction. Further study will aim at determining whether plasma treatment is effective at not only sanitization, but sterilization. This research was funded by a NASA grant at the Kennedy Space Center.

Space Crop Production↗

Enabling Coal Technology with Carbon Capture for Future Markets with Flameless Pressurized Oxy-Combustion (FPO)

Future markets for power are expected to require more load following power plants, which reduces output during the night and early morning. This is when the demand for electricity is the lowest, so plants must respond rapidly at any time to peak loads resulting from the variable output of wind and solar power. A coal power plant based on Flameless Pressurized Oxy-combustion (FPO) can go from 5% to 100% of capacity rate in less than 30 minutes in response to fluctuating demand, operating at capacity when power prices are highest. FPO is a proven oxy-combustion technology that was developed to recover energy from low ranking coal, other brown fuels and wastes. ITEA began developing FPO in 2003 on a 5-MWth pilot in Gioia del Colle, Italy, to destroy hazardous industrial waste and as such, design objectives were very high combustion efficiencies and capture of metals in the fuel in the vitreous slag. The technology was subsequently deployed in 2009 at the 15-MWth scale at the Jurong Island petrochemical cluster in Singapore for waste incineration. FPO is an oxy-combustion process whereby oxygen is separated from the air, and it is used in combustion with recirculated flue gas to maintain combustion temperatures at acceptable levels. The resultant flue gas is primarily CO 2 and water, which allows for a relatively simple and cheap CO 2 capture process. This is in contrast to air-combustion systems which require a complex and costly post-combustion capture (PCC) process. Coal is fed to the combustor slurried in water, and the combustor operates at elevated pressure (approximately 12 bar) which improves the overall efficiency and reduces the size and cost of the combustor. Notably, the FPO cycle maintains high efficiency by recovering most of the heat of vaporisation of the contained water. The combustor is designed to coalesce the molten ash particles so that they settle to the chamber walls and drain to the outlet, significantly reducing the particulate content in the exhaust gas and allowing the use of coals with up to 40% alkaline ash content. FPO is a low-emission technology: zero thermal NOx minimises overall NOx; any organic nitrogen is converted to elemental nitrogen (N2). Total organic content (TOC) at combustor exit is hundreds of times lower than for traditional combustion processes, with dioxin and furans close to zero. Work commenced on a DOE funded pilot demonstration project in October 2016 to provide the design for a 50-MWth FPO pilot plant that can fire a wide range of high-to-low rank coals. The project will investigate updating and improving the cycle for power generation with CO 2 capture by incorporating a turbo-expander with a principal steam power island that utilizes a heat recovery steam generator, increasing the overall efficiency of the cycle. A cost study is also performed on the updated FPO design as part of the project. The FPO pilot plant built based on the design will then be demonstrated over a 3-year test program to generate data for the design of a commercial-scale 500 MWth firing module commercial power plant with integral carbon capture and sequestration (CCS), which could start construction in 2025. A discussion of the levelized cost of electricity (LCOE) of various cases are presented, including a comparison of established supercritical with PCC (SCPC) technologies with FPO fitted with CO 2 compression and liquefaction, and FPO ready for carbon capture and sequestration (CCS-ready). This would enable CO 2 capture for use in enhanced oil recovery (EOR) or sequestration when market conditions make it attractive to do so. In addition, a comparison of LCOE of FPO and conventional processes for firing low-ranking coals with high water and ash content will be provided.

01 COAL, LIGNITE, AND PEAT↗

A Novel Matching Formulation for Startup Costs in Unit Commitment

We present a novel formulation for startup cost computation in the unit commitment problem (UC). Both the proposed formulation and existing formulations in the literature are placed in a formal, theoretical dominance hierarchy based on their respective linear programming relaxations. The proposed formulation is tested empirically against existing formulations on large-scale unit commitment instances drawn from real-world data. While requiring more variables than the current state-of-the-art formulation, our proposed formulation requires fewer constraints, and is empirically demonstrated to be as tight as a perfect formulation for startup costs. This tightening reduces the computational burden in comparison to existing formulations, especially for UC instances with large variability in net-load due to renewables production.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗