Search NASA⌕ Search

SEARCH · Search NASA

Results for “waveforms”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Transient corona effects on a wire over the ground

The nuclear EMP effect on VLF/trailing wire antennas is investigated in relation to new features of corona effects. Previous experimental results on transmission lines with corona under E 80 kV/cm recorded in the nanosecond time frame are analyzed. A nonlinear macroscopic model which describes a transmission line with corona is discussed. The model not only accounts for overall waveform, but also describes the sharp changes in the waveform associated with the corona onset.

Chen, K. C.↗
NASA NTRS1980

Initial direct strike lightning data

Data waveforms of the rate of change of electric flux density obtained during two lightning strikes to an aircraft specially instrumented for lightning electromagnetic measurements are presented. The aircraft was operating in a thunderstorm environment to elicit strikes. The instrumentation system configuration, flight conditions, and strike scenario showing probable lightning path on the aircraft are described. The waveforms, which were obtained at a 10 nanosecond sample interval, indicate significant excursions of the rate of change of electric flux density occurred over few hundred nanoseconds time interval.

Pitts, F. L.↗
NASA NTRS1979

Gravitational waves from rotating and precessing rigid bodies - Simple models and applications to pulsars

An axially symmetric, torque-free rigid body, rotating and precessing, emits gravitational quadrupole radiation at two frequencies, omega and 2 omega, corresponding to the l = 2, m = 1,2 spherical harmonics. The paper presents explicitly the waveforms of the two polarizations at both frequencies. From observations of gravitational waves, one can derive information about the body's orientation and its precession amplitude. Electromagnetic radiation emitted by a spot fixed on the surface of the body arrives in pulses at a mean frequency Omega which is typically different from omega. If the body is not axially symmetric but the amplitude of the precession is small, the gravitational radiation at the lower frequency omega is split into two frequencies on either side of the electromagnetic pulse frequency. Explicit waveforms for the two polarizations in this case are also presented.

Zimmermann, M.↗
NASA NTRS1980

Gravitational waves from rotating and precessing rigid bodies. II - General solutions and computationally useful formulas

A rigid, freely precessing Newtonian body emits gravitational radiation. In this paper the classical-mechanics results for free precession which are needed in order to calculate the weak-field slow-motion quadrupole-moment gravitational waves are reviewed. Within that formalism, algorithms for computing the exact gravitational power radiated and waveforms produced by arbitrary rigid-body freely precessing source are given. Also presented are the dominant terms in series expansions of the waveforms for the case of an almost-spherical object precessing with a small wobble angle. These series expansions, which retain the precise frequency dependence of the waves, may be useful for gravitational astronomers when freely precessing sources begin to be observed.

Zimmermann, M.↗
NASA NTRS1980

Distributed microprocessors in a tactical universal modem

The distributed microprocessor system associated with a wideband signal conversion unit (WBSCU) is described. Multiple embedded 8086 and 2901 microprocessors, supported by dedicated hardware modules, perform the required real time operations for both transmit and receive functions. Commands from a host computer determine the configuration of the WBSCU via the IEEE 488 bus. Each of the four WBSCU channels is assigned to process a specified IF waveform; each channel configures its own resources and, in some cases, borrows resources from other channels. The processed waveform data is communicated from individual channels to redundant global memories. Data flow between the user community and global memories occurs via redundant 1553 buses through intelligent Bus Interface Units. Each WBSCU channel contains one 2901 bit slice machine and one 8086 microprocessor. The 2901 provides high speed processing capability for the most time critical operations. The 8086 is used for lower speed processing tasks where its high level language capability can be better exploited. Each 8086 has a global bus for wideband interprocessor communication, and a local bus for 8086/2901, master/slave communication. Software architecture consists of a control and communications structure governing mode dependent signal processing tasks.

Gray, D. M.↗
NASA NTRS1981

Acousto-ultrasonic characterization of fiber reinforced composites

The acousto-ultrasonic technique combines advantageous aspects of acoustic emission and ultrasonic methodologies. Acousto-ultrasonics operates by introducing a repeating series of ultrasonic pulses into a material. The waves introduced simulate the spontaneous stress waves that would arise if the material were put under stress as in the case of acoustic emission measurements. These benign stress waves are detected by an acoustic emission sensor. The physical arrangement of the ultrasonic (input) transducer and acoustic emission (output) sensor is such that the resultant waveform carries an imprint of morphological factors that govern or contribute to material performance. The output waveform is complex, but it can be quantitized in terms of a 'stress wave factor.' The stress wave factor, which can be defined in a number of ways, is a relative measure of the efficiency of energy dissipation in a material. If flaws or other material anomalies exist in the volume being examined, their combined effect appears in the stress wave factor.

Vary, A.↗
NASA NTRS1980

Dynamic modeling of brushless dc motors for aerospace actuation

A discrete time model for simulation of the dynamics of samarium cobalt-type permanent magnet brushless dc machines is presented. The simulation model includes modeling of the interaction between these machines and their attached power conditioners. These are transistorized conditioner units. This model is part of an overall discrete-time analysis of the dynamic performance of electromechanical actuators, which was conducted as part of prototype development of such actuators studied and built for NASA-Johnson Space Center as a prospective alternative to hydraulic actuators presently used in shuttle orbiter applications. The resulting numerical simulations of the various machine and power conditioner current and voltage waveforms gave excellent correlation to the actual waveforms collected from actual hardware experimental testing. These results, numerical and experimental, are presented here for machine motoring, regeneration and dynamic braking modes. Application of the resulting model to the determination of machine current and torque profiles during closed-loop actuator operation were also analyzed and the results are given here. These results are given in light of an overall view of the actuator system components. The applicability of this method of analysis to design optimization and trouble-shooting in such prototype development is also discussed in light of the results at hand.

Demerdash, N. A.↗
NASA NTRS1981

Acousto-ultrasonic characterization of fiber reinforced composites

The acousto-ultrasonic technique combines advantageous aspects of acoustic emission and ultrasonic methodologies. Acousto-ultrasonics operates by introducing a repeating series of ultrasonic pulses into a material. The waves introduced simulate the spontaneous stress waves that would arise if the material were put under stress as in the case of acoustic emission measurements. These benign stress waves are detected by an acoustic emission sensor. The physical arrangement of the ultrasonic (input) transducer and acoustic emission (output) sensor is such that the resultant waveform carries an imprint of morphological factors that govern or contribute to material performance. The output waveform is quite complex, but it can be quantitized in terms of a 'stress wave factor'. The stress wave factor, which can be defined in a number of ways, is essentially a relative measure of the efficiency of energy dissipation in a material. If flaws or other material anomalies exist in the volume being examined, their combined effect will appear in the stress wave factor.

Vary, A.↗
NASA NTRS1981

Boundary detection criteria for satellite altimeters

A procedure for using satellite altimeter data to determine the time of crossing of a surface boundary, such as ocean land or ocean ice, with the primary objective to flag altimeter data that do not properly represent oceanographic measurements were studied. Water to land crossing and water to sea ice crossing were investigated. For ocean ice crossings, a large increase in AGC occurred. Waveform tests for increasing the probability of detecting an ocean land crossing were investigated. It is recommended that the boundary test be based on a fit of the full waveform to a limited parameter set at a rate of 5 to 10 second.

Martin, C. F.↗
NASA NTRS1980

Risetime distortion of Shuttle Ku-band payload 50 MBPS data due to coaxial cable skin effects

This paper discusses distortion of digital signals generated in the Space Shuttle Ku-band communications systems. Specifically, the degradation considered is due to coaxial cables which interface data and clock from a source located in the payload bay to the KuSPA (Ku-Band Signal Processor Assembly) located in the avionics bay of the Shuttle. Due to the length (nearly 100 feet) and relatively narrow bandwidth of the cable, the clock and data waveforms are significantly affected by this transmission medium. This paper presents a closed form model that closely approximates the distortion of the waveforms measured in laboratory tests.

Schadelbauer, S.↗
NASA NTRS1982

A 10-kW series resonant converter design, transistor characterization, and base-drive optimization

The development, components, and performance of a transistor-based 10 kW series resonant converter for use in resonant circuits in space applications is described. The transistors serve to switch on the converter current, which has a half-sinusoid waveform when the transistor is in saturation. The goal of the program was to handle an input-output voltage range of 230-270 Vdc, an output voltage range of 200-500 Vdc, and a current limit range of 0-20 A. Testing procedures for the D60T and D7ST transistors are outlined and base drive waveforms are presented. The total device dissipation was minimized and found to be independent of the regenerative feedback ratio at lower current levels. Dissipation was set at within 10% and rise times were found to be acceptable. The finished unit displayed a 91% efficiency at full power levels of 500 V and 20 A and 93.7% at 500 V and 10 A.

Robson, R. R.↗
NASA NTRS1983

Microprocessor-Based Neural-Pulse-Wave Analyzer

Microprocessor-based system analyzes amplitudes and rise times of neural waveforms. Displaying histograms of measured parameters helps researchers determine how many nerves contribute to signal and specify waveform characteristics of each. Results are improved noise rejection, full or partial separation of overlapping peaks, and isolation and identification of related peaks in different histograms. 2

Kojima, G. K.↗
NASA NTRS1982

Acousto-ultrasonic characterization of fiber reinforced composites

The advantageous aspects of acoustic emission and ultrasonic methodologies are combined in a technique which operates by introducing a repeating series of ultrasonic pulses into a material. The waves introduced simulate the spontaneous stress waves that would arise if the material were put under stress as in the case of acoustic emission measurements. These benign stress waves are detected by an acoustic emission sensor. The physical arrangement of the ultrasonic (input) transducer and acoustic emission (output) sensor is such that the resultant waveform carries an imprint of morphological factors that govern or contribute to material performance. The output waveform is quite complex, but it can be quantitized in terms of a "stress wave factor". The stress wave factor, which can be defined in a number of ways, is essentially a relative measure of the efficiency of energy dissipation in a material. If flaws or other material anomalies exist in the volume being examined, their combined effect will appear in the stress wave factor.

Vary, A.↗
NASA NTRS1983

the P-wave upper mantle structure beneath an active spreading center: The Gulf of California

Detailed analysis of short period travel time, and waveform data reveals the upper mantle structure beneath an oceanic ridge to depths of 900 km. More than 1400 digital seismograms from earthquakes in Mexico and central America recorded at SCARLET yield 1753 travel times and 58 direct measurements of short period travel time as well as high quality, stable waveforms. The 29 events combine to form a continuous record section from 9 deg to 40 deg with an average station spacing of less than 5 km. First the travel times are inverted. Further constraints arise from the observed relative amplitudes of mantle phases, which are modeled by trial and error.

Walck, M. C.↗
NASA NTRS1983

SEASAT radar altimeter measurements over the Florida Everglades

The SEASAT satellite radar altimeter traversed the Florida Everglades on August 14, 1978. Analysis of the measurements disclosed that the altimeter pulses from 800 km above the Earth's surface penetrated the vegetation canopies to provide land and water surface elevations with accuracies better than + or - 50 cm. The altimeter waveforms required retracking over the specular Everglades surface. The altimeter-derived land elevations were correlated with large-scale topographic maps while the altimeter-derived water elevations were correlated with water gauge records of the U.S. Geological Survey. Examination of the altimeter waveforms also revealed reflections from the Everglades' surface occurring earlier than the surface reflections. These earlier surface reflections are interpreted to be from vegetation canopies, and may provide a measure of vegetation canopy heights. Future satellite radar altimeters could provide supplemental vertical control in relatively inaccessible swamp areas, could monitor water levels, and perhaps could monitor vegetation growth.

Brooks, R. L.↗
NASA NTRS1983

Adaptive reference voltage generator for firing angle control of line-commutated inverters

A control system for a permanent-magnet motor driven by a multiphase line-commulated inverter is described. It is provided with integrators for integrating the back EMF of each phase of the motor for use in generating system control signals for an inverter gate logic using a sync and firing angle control generator connected to the outputs of the integrators. The firing angle control signals are produced by the control generator by means for combining 120 deg segments of the integrated back EMF signals symmetrical about their maxima into composite positive and negative waveforms, and means for sampling the maxima of each waveform every 120 deg. These samples are then used as positive and negative firing angle control signals. Whereby any change in amplitude of the integrated back EMF signals will not affect a change in the operating power factor of the motor and inverter.

Dolland, C. R.↗
NASA NTRS1983

Model helicopter rotor high-speed impulsive noise: Measured acoustics and blade pressures

A 1/17-scale research model of the AH-1 series helicopter main rotor was tested. Model-rotor acoustic and simultaneous blade pressure data were recorded at high speeds where full-scale helicopter high-speed impulsive noise levels are known to be dominant. Model-rotor measurements of the peak acoustic pressure levels, waveform shapes, and directively patterns are directly compared with full-scale investigations, using an equivalent in-flight technique. Model acoustic data are shown to scale remarkably well in shape and in amplitude with full-scale results. Model rotor-blade pressures are presented for rotor operating conditions both with and without shock-like discontinuities in the radiated acoustic waveform. Acoustically, both model and full-scale measurements support current evidence that above certain high subsonic advancing-tip Mach numbers, local shock waves that exist on the rotor blades ""delocalize'' and radiate to the acoustic far-field.

Boxwell, D. A.↗
NASA NTRS1983

Application of the Lienard-Wiechert solution to a lightning return stroke model

The electric and magnetic fields associated with the lightning return stroke are expressed as a convolution of the current waveform shape and the fields generated by a moving charge of amplitude one (i.e., the Lienard-Wiechert solution for a unit charge). The representation can be used to compute the fields produced by a current waveform of non-uniform velocity that propagates along a filament of arbitrary, but finite, curvature. To study numerically the effects of linear charge acceleration and channel curvature two simple channel models are used: the linear and the hyperbolic.

Meneghini, R.↗