Search NASA⌕ Search

SEARCH · Search NASA

Results for “3D PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

3D Printed Microfluidic Supported Liquid Membrane Module for Radionuclide Separations

Microfluidic supported liquid membrane extraction is a promising technique for microliter-scale radionuclide separations because it requires very small reagent volumes and combines extraction and stripping in a single unit operation. Flat sheet supported liquid membrane (FS-SLM) modules with 100, 200, 300, and 400 μm deep channels were fabricated at a cost of less than 5 USD in material using a commercially available resin three-dimensional (3D) printer. The performance of these modules was characterized by quantifying uranium transport across a 15 v/v% tributyl phosphate (TBP) liquid membrane at flow rates between 5 and 60 μL min –1 and developing a two-dimensional (2D) numerical transport model for the system. The extent of uranium extraction was found to increase with increasing residence time and decreasing channel depth, with quantitative extraction occurring at the slowest flow rates and shallowest channel depths. The numerical model agreed well with the experimental extraction results. Time-dependent calculations showed that the modules reach steady state in fewer than 9 min and that there is a considerable buildup of uranium in the membrane during that time.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Identifying build orientation of 3D-printed materials using convolutional neural networks

The advent of additive manufacturing (AM) processes brought with it intense research into various materials and manufacturing processes. At the same time, the need for validation of material properties, as well as study and forecasting of aging, has arisen. Modern imaging techniques, like X-ray computed tomography (XCT), are a convenient vehicle for such studies; however, the large datasets they produce require novel analysis techniques to efficiently extract critical information. Here, we present our work on developing a 3D extension of the ResNet architecture to distinguish between two build orientations of tensile bars produced by AM. Using only information from XCT, our method achieves a 99.3% correct classification at a misidentification of 1%.

36 MATERIALS SCIENCE↗

3D Printing Catalytic Electrodes for Solar-Hydrogen Devices

Hydrogen production through water-splitting systems showed promising pathway to achieve <$2/kg cost target set by Department of Energy (DOE). As far, most efforts have been devoted to new electrocatalytical materials discovery. In contrast, the impact of architecture of the electrocatalysts as well as mass transport within the gas diffusion layers has not been well explored. In this project, we developed a new ink formulation with earth-abundant elements nickel and molybdenum (NiMo) for catalytical 3-dimentional (3D) electrodes in water-splitting devices. The NiMo electrodes fabricated via additive manufacturing have been characterized and tested. The architecture, morphology and compositions of the NiMo electrodes have been confirmed by Scanning Electric Microscopy (SEM) and Powder X-Ray Diffraction (XRD). We have demonstrated that the catalyst precursor survived the whole fabrication and post-treatment process. Furthermore, the NiMo 3D electrodes in this study exhibited state-of-art hydrogen evolution reaction (HER) performance, ~ 60 mV over potential for over 24 hours operation. The high performance of the 3D catalytical electrodes is attributed to large roughness factors (RF) of the electrodes and highly efficient mass transport. This study is in line with DOE initiative H2@Scale and national energy security missions at LLNL.

36 MATERIALS SCIENCE↗

Lithium–Sulfur Batteries: 3D Printed Tools and Assembly Techniques for Repeatable Lab-Scale Coin Cell Manufacturing

The coin cell form factor has become a standard in energy storage research owing to its relatively low cost, low quantity of requisite electroactive material, fast experimental turnover, and capability to generate publishable quality data. Coin cell assembly at the lab-scale requires precise manual alignment of the many internal components of a cell to yield a properly functioning device. Truly repeatable device assembly presents a significant challenge to the acquisition of reliable data. In this report, we present a three-dimensional (3D) printable design for a coin cell alignment device and describe techniques for a generalized workflow to achieve reproducible coin cell assembly of lithium-based batteries. Standardized assembly techniques using readily accessible, purpose-built tools were demonstrated for labscale production of lithium−sulfur (Li−S) coin cells. Li−S batteries fabricated using the alignment device as well as conductive adhesive incorporated workflows afforded coin cells with up to 35% reduction of assembly times, comparable or better functional cell yields, and improved electrochemical device performance with more consistent and up to 150 mAh/g higher average discharge capacities coupled with Coulombic efficiency increases of up to 2.0% over manually aligned cell assembly techniques.

Batteries↗

The Radical Atom: Mechanosynthetic 3D Printing of an Atomically Precise SPM Tip

This research effort sought to overcome current limitations in scanning probe-based atomic manipulation to enable atomically precise manufacturing (APM). Previous theoretical and experimental works on atom by atom and molecule by molecule fabrication of precise structures are limited to essentially to two-dimensions. APM will enable a paradigm shift in 21st century manufacturing practices in which every single atom in a electronic chip, device or machine can be placed in an exact and predefined position in three-dimensions. By providing a general method for generating reproducible SPM tip structure, this project will drive forward the entire field of atomically precise scanning probe microscopy, opening the door to positional control of nearly arbitrary covalent chemistry. Such control could, for example, be used in applications such as novel 2.5 or 3D microchip fabrication. The creation of a unique manufacturing method through APM has the potential to impact technologies at the theoretical limits of performance, weight, and utility including: solid-state quantum and spintronic computing systems, high efficiency optical antenna, solar power systems, defect engineered materials and extremely efficient catalysts. Although this experiment focused on pick-and-place non-scalable APM, the better understanding of the chemistry is crucial to the eventual goal of scalable APM. To place individual atoms into a specified location is a seminal aspiration of researchers and engineers in the many fields and may have early premium applications in medical devices and microelectronics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

MADE3D: Enabling the next generation of high-torque density wind generators by additive design and 3D printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments—especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technolgies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

17 WIND ENERGY↗

Magnox Reprocessing TDN Reactors: Utilising 3D Printing and X-Ray Imaging to Re-Design and Test Fluidising Air Nozzles - 16402

One of the key final steps in reprocessing spent nuclear fuel is the conversion of highly concentrated uranyl nitrate hexahydrate liquor [> 1000 gU/litre] into uranium trioxide (UO{sub 3}) powder by thermal decomposition using Thermal Denitration (TDN) reactors. The TDN reactors in the Magnesium non-oxidising (Magnox) fuel reprocessing plant are high aspect ratio fluidising beds, which suffer from poor fluidization and UO{sub 3} powder blockages. It is widely understood that these issues arise from the inadequate design of the fluidising air distributors (nozzles), which are located around the base of the TDN reactors. A non-active test rig was constructed at the National Nuclear Laboratory (NNL) experimental facility in Workington, Cumbria (UK) which used compressed air at ambient temperature to assess the performance of the current fluidising air nozzle designs (datum) against a range of new nozzle designs. Full-scale nozzle designs were manufactured using a 3-Dimensional (3D) printer and tested to obtain data of both quantitative and qualitative nature. NNL then collaborated with the Chemical Engineering Department at University College London (UCL) to further assess the fluidising potential of the new nozzle designs. Images of inside the fluidized bed were taken utilising a unique X-Ray facility. The results from this study will allow new nozzle designs to be recommended, manufactured and installed, which will ensure improved fluidization of the TDN reactor bed and prevent blockages with UO{sub 3} powder. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

3D Printing of Transparent Silicone Elastomers

Here in this paper, inks for transparent elastomers that are formulated by matching the refractive index of silica and polysiloxanes are described. The transparent inks transmit up to ≈90% of 700 nm light through 1 cm and remain transparent when solidified. The inks and solidified materials exhibit a thermochromic effect. This thermochromic effect can be controlled by the refractive index mismatch. Transparency may increase or decrease as temperature increases, depending on the refractive index mismatch of the base polysiloxane and silica. It is found that the rheological properties of the ink depend on the distribution of silica particles, which is dictated by silica functionality, weight content, and processing. Siloxane precursors that vary in chemical functionality are introduced to tailor the mechanical properties of the printed elastomers, which obtain stretchability >65% along with a tensile modulus of 1.9 MPa. After optimizing siloxane chemistry and ink processing, the authors are able to print transparent elastomers. Potential applications are demonstrated for printed structures by printing encapsulation structures for light-emitting diodes, semitransparent dye-filled structures, a microfluidic mixing device, and a multimaterial structure that exhibits temperature-dependent camouflage.

36 MATERIALS SCIENCE↗

Unlocking Larger Scales and Aspect Ratios in 3D Printed Glass: Coupling Active Mixing and UV Curing for Advanced Printability and Crack Resistance

Recent developments in additive manufacturing (AM) of glass via silica-filled inks have facilitated fabrication of previously unattainable geometries and compositions. However, the maximum processable size of 15 mm limits the use of these prints in applications such as optics. A key limitation lies in the trade-off between material printability and green strength: increasing silica content in the feedstock improves crack resistance and reduces shrinkage but results in dramatic changes in viscoelastic properties that hinder flowability. Here, this paper presents a novel approach that offers expanded versatility in processable size, feedstock formulation, and printing. Described here is a direct ink writing (DIW) system coupled with an active high-shear micromixer and UV light source, capable of simultaneously printing multiple inks with a wide range of rheological properties. Choice of silica sourc, solvent, UV-curable binder, and dispersant is used to tune the ink rheology and improve printability and mechanical properties. Imparting high shear with the micromixer while UV-curing the extrudate allows for increased ink viscosities and reduced nozzle diameters, enabling printing finer feature sizes. With these advances, thin-walled high-aspect ratio structures and a crack-free glass disk measuring 44 mm in diameter are demonstrated, an increase of 3× in the greatest dimension compared to current state-of-the-art.

36 MATERIALS SCIENCE↗

Overcoming the Damping–Elasticity Paradox via 3D‐Printed NiTiSn Nanocomposite

Abstract Developing high damping alloys (HDAs) with large elastic strain has attracted growing attention due to the increasing demand for energy absorption with overload reliability and reusability. However, damping capacity inherently conflicts with elasticity, because the former requires a liable movement of crystal defects while the latter opposite. To deal with the damping‐elasticity paradox, the advantage of pseudobinary eutectic reaction and rapid cooling of laser powder bed fusion is taken to fabricate a bulk NiTiSn nanocomposite with a two‐level hierarchical structure. The first‐level architecture is composed of martensitic NiTi nanolamellae and reinforced Ti 3 Sn nanolamellae. In addition to lattice strain matching and lamellar boundary strengthening, a novel mechanism of martensite reorientation mediated by reversible stress‐induced detwinning‐twinning is activated to generate large elastic strain. A high density of nanotwins and nanodomains within NiTi nanolamellae constitute the second‐level architecture, which provides pronounced internal friction for high damping capacity. As a result, our NiTiSn nanocomposite exhibits a record‐high integration of damping capacity (tanδ > 0.10) and elastic strain (exceeding 4.5%), as well as superb stability under cyclic overload. This research not only represents a major breakthrough in achieving HDAs with outstanding damping and elastic strain but also offers a novel paradigm for high‐performance functional and structural materials.

Chemistry↗

Process intensification of CO 2 absorption using a 3D printed intensified packing device

In this study, we present a first of its kind demonstration of successful enhancement of CO 2 chemical absorption, under selected conditions, using a process intensification approach. A multifunctional device that integrates contact of phases and heat exchange has been developed, characterized, and tested. Heat transfer analysis has demonstrated the efficacy of the device as a heat exchanger, and mass transfer results have shown substantial improvement in the uptake of CO 2 under a range of operating conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Toluene Uptake and Outgassing by a 3D-Printed Silicone and the Impact on Mechanical Performance

Silicone elastomers have advantageous physical properties and are widely used in various applications. Additive manufacturing (AM) of silicones provides additional utility by enabling tunable mechanical and functional properties. However, the performance of these elastomers deteriorates over time with exposure to environmental stressors. Organic solvents and volatile organic compounds (VOCs) are stressors that can cause dimensional changes to silicones with exposure and impact the overall function. Yet, the effects of such exposure on mechanical performance, including load response (LR), are not well understood. Here, in this study, we investigated the impact of a nonpolar solvent, toluene, on AM silicone material properties and compressive load. We observed that AM silicones rapidly absorbed toluene and swelled, leading to an increase in relative LR. Toluene concentration and compression did not affect uptake or swelling rates. In contrast, outgassing rates were slower for compressed coupons compared to uncompressed specimens, attributed to geometric constraints and polymer network changes impacting toluene diffusion outward. Compression also pinned the AM silicones at an enlarged state, significantly reducing relative LR after outgassing. Depending on toluene concentrations and compression, AM silicones can remain robust against toluene exposure and recover their initial printing geometry and mechanical performance after toluene outgassing and polymer relaxation.

Materials science↗

Novel pore size-controlled, susceptibility matched, 3D-printed MRI phantoms

We report the design concept and fabrication of MRI phantoms, containing blocks of aligned microcapillaires that can be stacked into larger arrays to construct diameter distribution phantoms or fractured, to create a “powder-averaged” emulsion of randomly oriented blocks for vetting or calibrating advanced MRI methods, that is, diffusion tensor imaging, AxCaliber MRI, MAP-MRI, and multiple pulsed field gradient or double diffusion-encoded microstructure imaging methods. The goal was to create a susceptibility-matched microscopically anisotropic but macroscopically isotropic phantom with a ground truth diameter that could be used to vet advanced diffusion methods for diameter determination in fibrous tissues. Two-photon polymerization, a novel three-dimensional printing method is used to fabricate blocks of capillaries. Double diffusion encoding methods were employed and analyzed to estimate the expected MRI diameter. Susceptibility-matched microcapillary blocks or modules that can be assembled into large-scale MRI phantoms have been fabricated and measured using advanced diffusion methods, resulting in microscopic anisotropy and random orientation. This phantom can vet and calibrate various advanced MRI methods and multiple pulsed field gradient or diffusion-encoded microstructure imaging methods. We demonstrated that two double diffusion encoding methods underestimated the ground truth diameter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Analysis of thermal history effects on mechanical anisotropy of 3D-printed polymer matrix composites via in situ X-ray tomography

The tensile behavior of an additively manufactured (AM) polymer matrix composite (PMC) is studied with in situ X-ray computed microtomography (CT) and digital volume correlation (DVC). In this experiment, the effects of recycled material content and print direction on the selective laser-sintered (SLS) material's mechanical response are explored. The PMC samples are printed in a tensile specimen geometry with gage lengths parallel to all three orthogonal, primary sintering directions. In situ tensile-CT experiments are conducted at Argonne National Laboratory's Advanced Photon Source 2-BM beamline. Analysis of the AM PMC's tensile response, failure, and strain evolution is analyzed both from a conventional standpoint, using the load-displacement data recorded by the loading fixture, and from a microstructural standpoint by applying DVC analysis to the reconstructed volumes. Significant variations on both strength and ductility are observed from both vantages with respect to print direction and the recycled material content in the printed parts. As a result, it is found that the addition of recycled source material with a thermal history reduces the tensile strength of the SLS composite for all directions, but the effect is drastic on the strength in the layering direction.

36 MATERIALS SCIENCE↗