Search NASA⌕ Search

SEARCH · Search NASA

Results for “ATMOSPHERIC EXPLOSIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Quantifying fission gas adsorption onto natural clinoptilolite in the presence of environmental air and water

Adsorption of noble gas fission products onto naturally occurring minerals is of interest for its potential to retain or retard emissions from nuclear fuel reprocessing operations or underground nuclear explosions. However, experimental studies of trace noble gas adsorption in the presence of air and water have largely focused on synthetic materials, such as activated carbon or metal-organic frameworks. Here, in this study, adsorption of Kr and Xe onto the naturally occurring zeolitic mineral clinoptilolite is studied in the presence of nitrogen and water. By varying the composition of the gas phase and monitoring the change in the combined adsorbate mass, the adsorbed concentration of noble gas is calculated gravimetrically. For dry clinoptilolite, the concentration of adsorbed Kr and Xe is linearly correlated with noble gas pressure and Henry's Law appears satisfactory, despite the presence of nitrogen at atmospheric pressures. However, the presence of water significantly reduces the adsorbed concentration of both Kr and Xe, which is typical in nanoporous sorbents. Here, an empirical bivariate model is presented, combining the Henry's Law adsorption model for a dry adsorbent with the exponential reduction in the presence of water, as reported by Lungu and Underhill in 1999. This model provides a means to estimate the adsorbate concentration at the trace partial pressures and higher water contents relevant to field-scale modeling of fission gas transport through the vadose zone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Non-solar UV produced ions observed optically from the 'Crit I' critical velocity ionization experiment

A critical velocity ionization experiment was carried out with a heavily instrumented rocket launched from Wallops Island on May 13, 1986. Two neutral barium beams were created by explosive shaped charges released from the rocket and detonated at 48 deg to B at altitudes near 400 km and below the solar UV cutoff. Critical velocity ionization was expected to form a detectable ion jet along the release field line, but, instead, an ion cloud of fairly uniform intensity was observed stretching from the release field line across to where the neutral barium jet reached sunlight. The process creating these ions must have been present from the time of the release; the efficiency is estimated to be equivalent to an ionization time constant of 1800 sec. This ionization is most likely from collisions between the neutral barium jet and the ambient atmospheric oxygen, and, if so, the cross section for collisional ionization is 9 x 10 to the -18th sq cm.

Stenbaek-Nielsen, H. C.↗

The heating of nova ejecta by radioactive decays of the beta-unstable nuclei

Recent nucleosynthesis and hydrodynamic calculations of the consequences of accretion onto massive ONeMg white dwarf stars show that under certain circumstances significant amounts of the beta-unstable nuclei can be produced and ejected by the resulting explosion. We use these calculations as a guide in order to obtain the conditions under which the heating of the ejected material by the nonthermal electrons and positrons produced by the decays of the beta-unstable nuclei is sufficient to overcome the cooling from adiabatic expansion and lead to the production of X-ray-emitting coronal gas. These conditions are as follows: (1) a mass fraction for Na-22 of the order of 10(exp -3) or greater, (2) an expansion velocity in the range approximately 10(exp 2) - 10(exp 3) km/s, (3) a photospheric radius of approximately 10(exp 14) cm, (4) if the density distribution in the atmosphere satisfies a power law, then the exponent must be less than 3 for heating to overcome adiabatic cooling. Both the simulations of the outburst and the model atmosphere fits to the observed energy distributions, however, imply that the exponent is greater than or = 3 during the early phases of the outburst. Nevertheless, for a value of the exponent of 2, we predict the time when hot coronal gas can form during the expansion phases of the envelope.

Pistinner, Shlomi↗

Growing Pacific Linkage with Western North Atlantic Explosive Cyclogenesis

Abstract Explosive cyclones (ECs), defined as extratropical cyclones that experience normalized pressure drops of at least 24 hPa in 24 h, are impactful weather events in the North Atlantic sector, but year-to-year changes in the frequency and impacts of these storms are sizeable. To analyze the sources of this interannual variability, we track cases of ECs and dissect them into two spatial groups: those that formed near the east coast of North America (coastal) and those in the north central Atlantic (high latitude). The frequency of high-latitude ECs is strongly correlated with the North Atlantic Oscillation, a well-known feature, whereas coastal EC frequency is statistically linked with an atmospheric wave train emanating from the North Pacific in the last 30 years. This wave train pattern of alternating high and low pressure is associated with heightened upper-level divergence and Eady growth rates along the east coast of North America, likely resulting in a stronger correspondence between the atmospheric wave train and coastal EC frequency. Using coupled model experiments, we show that the tropical and North Pacific oceans are an important factor for this atmospheric wave train and the subsequent enhancement of seasonal baroclinicity in the North Atlantic.

58 GEOSCIENCES↗

AI techniques for a space application scheduling problem

Scheduling is a very complex optimization problem which can be categorized as an NP-complete problem. NP-complete problems are quite diverse, as are the algorithms used in searching for an optimal solution. In most cases, the best solutions that can be derived for these combinatorial explosive problems are near-optimal solutions. Due to the complexity of the scheduling problem, artificial intelligence (AI) can aid in solving these types of problems. Some of the factors are examined which make space application scheduling problems difficult and presents a fairly new AI-based technique called tabu search as applied to a real scheduling application. the specific problem is concerned with scheduling application. The specific problem is concerned with scheduling solar and stellar observations for the SOLar-STellar Irradiance Comparison Experiment (SOLSTICE) instrument in a constrained environment which produces minimum impact on the other instruments and maximizes target observation times. The SOLSTICE instrument will gly on-board the Upper Atmosphere Research Satellite (UARS) in 1991, and a similar instrument will fly on the earth observing system (Eos).

Thalman, N.↗

MISR Observations of Etna Volcanic Plumes

In the last twelve years, Mt. Etna, located in eastern Sicily, has produced a great number of explosive eruptions. Volcanic plumes have risen to several km above sea level and created problems for aviation and the communities living near the volcano. A reduction of hazards may be accomplished using remote sensing techniques to evaluate important features of volcanic plumes. Since 2000, the Multiangle Imaging SpectroRadiometer (MISR) on board NASA s Terra spacecraft has been extensively used to study aerosol dispersal and to extract the three-dimensional structure of plumes coming from anthropogenic or natural sources, including volcanoes. In the present work, MISR data from several explosive events occurring at Etna are analyzed using a program named MINX (MISR INteractive eXplorer). MINX uses stereo matching techniques to evaluate the height of the volcanic aerosol with a precision of a few hundred meters, and extracts aerosol properties from the MISR Standard products. We analyzed twenty volcanic plumes produced during the 2000, 2001, 2002-03, 2006 and 2008 Etna eruptions, finding that volcanic aerosol dispersal and column height obtained by this analysis is in good agreement with ground-based observations. MISR aerosol type retrievals: (1) clearly distinguish volcanic plumes that are sulphate and/or water vapor dominated from ash-dominated ones; (2) detect even low concentrations of volcanic ash in the atmosphere; (3) demonstrate that sulphate and/or water vapor dominated plumes consist of smaller-sized particles compared to ash plumes. This work highlights the potential of MISR to detect important volcanic plume characteristics that can be used to constrain the eruption source parameters in volcanic ash dispersion models. Further, the possibility of discriminating sulphate and/or water vapor dominated plumes from ash-dominated ones is important to better understand the atmospheric impact of these plumes.

Scollo, S.↗

Measurements of Argon-39 from locations near historic underground nuclear explosions

Measurement of radioactive gas seepage from an underground nuclear explosion is one of the primary methods to confirm whether an event was nuclear in nature. Radioactive noble gas indicators that are commonly targeted by such measurements (e.g. 133Xe, 37Ar) have half-lives of 35 days or less. Argon-39, an activation product similar to 37Ar, is produced by the interaction between neutrons and potassium in the surrounding geology and has a half-life of 269 years. Measurements taken at three sites near three historic underground nuclear test locations at the Nevada National Security Site have all shown highly elevated levels of 39Ar in subsurface air decades after the test events. Elevated levels of 39Ar (30-50 times background) were also detected in atmospheric air collected roughly 30 cm above ground level near two of these sites, and outside the entrance of the one tunnel site. These measurements demonstrate that 39Ar has the potential to be a long-term signature of an underground nuclear event which can be reliably detected at the surface or in the shallow subsurface. This radionuclide detection of an underground nuclear event decades after the event takes place is in contrast to the commonly held assumption that detecting underground nuclear events via radionuclides at the surface needs to be done in a matter of months. Depending upon what further studies show about the robustness of this signature in a variety of geological settings, it may in fact be easy to detect underground nuclear events at the surface for a very long time post-detonation.

Johnson, Christine M.↗

Acoustic Event Location and Background Noise Characterization on a Free Flying Infrasound Sensor Network in the Stratosphere

We present that a variety of Earth surface and atmospheric sources generate low frequency sound waves that can travel great distances. Despite a rich history of ground-based sensor studies, very few experiments have investigated the prospects of free floating microphone arrays at high altitudes. However, recent initiatives have shown that such networks have very low background noise and may sample an acoustic wave field that is fundamentally different than that at Earth’s surface. The experiments have been limited to at most two stations at altitude, making acoustic event detection and localization difficult. We describe the deployment of four drifting microphone stations at altitudes between 21 and 24 km above sea level. The stations detected one of two regional ground-based chemical explosions as well as the ocean microbarom while traveling almost 500 km across the American Southwest. The explosion signal consisted of multiple arrivals; signal amplitudes did not correlate with sensor elevation or source range. The waveforms and propagation patterns suggest interactions with gravity waves in the 35-45 km altitude. A sparse network method that employed curved wave front corrections was able to determine the backazimuth from the free flying network to the acoustic source. Episodic signals similar to those seen on previous flights in the same region were noted, but their source remains unclear. Lastly, background noise levels were commensurate with those on infrasound stations in the International Monitoring System below 2 seconds.

58 GEOSCIENCES↗

Fibrous-Ceramic/Aerogel Composite Insulating Tiles

Fibrous-ceramic/aerogel composite tiles have been invented to afford combinations of thermal-insulation and mechanical properties superior to those attainable by making tiles of fibrous ceramics alone or aerogels alone. These lightweight tiles can be tailored to a variety of applications that range from insulating cryogenic tanks to protecting spacecraft against re-entry heating. The advantages and disadvantages of fibrous ceramics and aerogels can be summarized as follows: Tiles made of ceramic fibers are known for mechanical strength, toughness, and machinability. Fibrous ceramic tiles are highly effective as thermal insulators in a vacuum. However, undesirably, the porosity of these materials makes them permeable by gases, so that in the presence of air or other gases, convection and gas-phase conduction contribute to the effective thermal conductivity of the tiles. Other disadvantages of the porosity and permeability of fibrous ceramic tiles arise because gases (e.g., water vapor or cryogenic gases) can condense in pores. This condensation contributes to weight, and in the case of cryogenic systems, the heat of condensation undesirably adds to the heat flowing to the objects that one seeks to keep cold. Moreover, there is a risk of explosion associated with vaporization of previously condensed gas upon reheating. Aerogels offer low permeability, low density, and low thermal conductivity, but are mechanically fragile. The basic idea of the present invention is to exploit the best features of fibrous ceramic tiles and aerogels. In a composite tile according to the invention, the fibrous ceramic serves as a matrix that mechanically supports the aerogel, while the aerogel serves as a low-conductivity, low-permeability filling that closes what would otherwise be the open pores of the fibrous ceramic. Because the aerogel eliminates or at least suppresses permeation by gas, gas-phase conduction, and convection, the thermal conductivity of such a composite even at normal atmospheric pressure is not much greater than that of the fibrous ceramic alone in a vacuum.

White, Susan M.↗

Remote Sensing of the Ocean Surface Refractive Index via Short-Wave Infrared Polarimetry

The linear polarization of sunlight reflected by ocean surfaces in the shortwave infrared (SWIR), at geometries where specular reflection dominates the signal, is a direct function of the refractive index of the surface microlayer(SML). This simple physical concept is at the base of a novel technique presented in this study. We invert observations obtained by the airborne Research Scanning Polarimeter (RSP) in the sun glint region, where each pixel's radiance is dominated by the signal originating from the wave slopes oriented precisely to cause specular reflection. The SWIR wavelength ensures minimization of aerosol interference when radiance travels through the atmosphere; strong absorption by the water body then limits the penetration depth to the first micrometer or so, effectively probing the SML. The resulting Degree of Linear Polarization (DoLP) is then governed by the refractive index via the Fresnel law for the specfic pixel geometry, independently of the wind speed. The selected dataset concerns several field deployments from both low- and high-altitude aircraft, including total reflectance measurements with the sole purpose of accounting for the residual aerosol effect.Stable retrievals from transects above pure seawater yielded values of refractive index that match the values published in the literature within an accuracy of 5 x 10 [superscript 4]. Flying over the oil spill caused by the explosion of the Deepwater Horizon platform, detected variations were found compatible with the presence of an oil slick. The robustness of the results, guaranteedby the high RSP polarimetric accuracy (less than or equal to 0:2%), opens the possibility for remote-sensing detection of other entities that similarly affect the refractive index including whitecaps, microplastics, biological gels, seaweed and grass mats.

Surface Microlayer↗

Stratospheric aerosols and climatic change

Generated primarily by volcanic explosions, a layer of submicron silicate particles and particles made of concentrated sulfuric acids solution is present in the stratosphere. Flights through the stratosphere may be a future source of stratospheric aerosols, since the effluent from supersonic transports contains sulfurous gases (which will be converted to H2SO4) while the exhaust from Space Shuttles contains tiny aluminum oxide particles. Global heat balance calculations have shown that the stratospheric aerosols have made important contributions to some climatic changes. In the present paper, accurate radiative transfer calculations of the globally-averaged surface temperature (T) are carried out to estimate the sensitivity of the climate to changes in the number of stratospheric aerosols. The results obtained for a specified model atmosphere, including a vertical profile of the aerosols, indicate that the climate is unlikely to be affected by supersonic transports and Space Shuttles, during the next decades.

Baldwin, B.↗

Evaluating the Capability of High-Altitude Infrasound Platforms to Cover Gaps in Existing Networks.

A variety of Earth surface and atmospheric sources generate low frequency sound waves that can travel great distances. Despite a rich history of ground-based sensor studies, very few experiments have investigated the prospects of free floating microphone arrays at high altitudes. However, recent initiatives have shown that such networks have very low background noise and may sample an acoustic wave field that is fundamentally different than that at the Earth's surface. The experiments have been limited to at most two stations at altitude, limiting their utility in acoustic event detection and localization. We describe the deployment of five drifting microphone stations at altitudes between 21 and 24 km above sea level. The stations detected one of two regional ground-based explosions as well as the ocean microbarom while traveling almost 500 km across the American Southwest. The explosion signal consisted of multiple arrivals; signal amplitudes did not correlate with sensor elevation or source range. A sparse network method that employed curved wave front corrections was able to determine the backazimuth from the free flying network to the acoustic source. Episodic broad band signals similar to those seen on previous flights in the same region were noted as well, but their source remains unclear. Background noise levels were commensurate with those on infrasound stations in the International Monitoring System (IMS) below 2 seconds, but sensor self noise appears to dominate at higher frequencies.

47 OTHER INSTRUMENTATION↗

Ultrahigh-energy neutrino astronomy

High-energy cosmic-ray interactions can produce neutrinos. The neutrino fluxes are calculated over a range of energies. The sources considered (and their ranges of importance) are cosmic-ray interactions in earth's atmosphere (neutrino energies less than 10,000 GeV), cosmic-ray interactions with ambient hydrogen in galaxies (neutrino energies between 10,000 and 1 million GeV), regions of cosmic-ray acceleration - e.g., pulsars - and cosmic-ray interactions with the microwave background radiation (neutrino energies greater than 100 million GeV). In addition, estimates of the flux from compact sources, such as active galaxies, are made. These flux levels, calculated conservatively, may be high enough for practical detection with a 1-cu km seawater detector; i.e., count rates greater than 1 per day. Such observations would provide information mainly about high-energy physics, but also (over long times) about cosmic-ray spectra, composition, and acceleration, as well as supernova and galactic-nucleus explosions.

Margolis, S. H.↗

The r-process and neutrino-heated supernova ejecta

As a neutron star is formed by the collapse of the iron core of a massive star, its Kelvin-Helmholtz evolution is characterized by the release of gravitational binding energy as neutrinos. The interaction of these neutrinos with heated material above the neutron star generates a hot bubble in an atmosphere that is nearly in hydrostatic equilibrium and heated, after approximately 10 s, to an entropy of S/N(sub AS)k greater than or approximately = 400. The neutron-to-proton ratio for material moving outward through this bubble is set by the balance between neutrino and antineutrino capture on nucleons. Because the electron antineutrino spectrum at this time is hotter than the electron neutrino spectrum, the bubble is neutron-rich (0.38 less than or approximately = Y(sub e) less than or approximately = 0.47). Previous work using a schematic model has shown that these conditions are well suited to the production of heavy elements by the r-process. In this paper we have advanced the numerical modeling of a 20 solar mass 'delayed' supernova explosion to the point that we can follow the detailed evolution of material moving through the bubble at the late times appropiate to r-process nucleosynthesis. The supernova model predicts a final kinetic energy for the ejecta of 1.5 x 10(exp 51) ergs and leaves behind a remnant with a baryon mass of 1.50 solar mass (and a gravitational mass of 1.445 solar mass). We follow the thermodynamic and compositional evolution of 40 trajectories in rho(t), T(t), Y(sub e)(t) for a logarithmic grid of mass elements for the last approximately = 0.03 solar mass to be ejected by the proto-neutron star down to the last less than 10(exp -6) solar mass of material expelled at up to approximately = 18 s after core collapse. We find that an excellent fit to the solar r-process abundance distribution is obtained with no adjustable parameters in the nucleosynthesis calculations. Moreover, the abundances are produced in the quantities required to account for the present Galactic abundances. However, at earlier times, this one-dimensional model ejects too much material with entropies S/N(sub A)k approximately 50 and Y(sub e) approximately 0.46. This leads to an acceptable over production of N = 50 nuclei, particularly Sr-88, Y-89, and Zr-90, relative to their solar abundances. We speculate on various means to avoid the early overproduction and/or ejection of N = 50 isotonic nuclei while still producing and ejecting the correct amount of r-process material.

Woosley, S. E.↗

The Development of a CO2 Test Capability in the NASA JSC ARCJet for Mars Reentry Simulation

The Atmospheric Reentry Materials and Structures Evaluation Facility (ARMSEF) located at NASA Johnson Space Center is used for simulating the extreme environment experienced upon reentry for the development and certification of thermal protection systems (TPS). The facility supports a large variety of programs and was heavily leveraged for the certification and operational support of the TPS for the Orbiter and, more recently, the development of the heat shield for CEV. This paper will provide more detail into the heritage of the facility. Unique attributes of the facility include a modular aerodynamically stabilized arc heater and independently controlled O2 and N2 for the test gases. When combining the O2 and N2 in a 23:77 mass ratio respectively the Earth s atmosphere is accurately simulated and via modification of this ratio the investigation of the effects of atomic oxygen on a material s response is possible. In the summer of 2010 a development effort was started to add CO2 as a third independently controlled test gas such that, when combined with N2, opens up the possibility of accurately simulating a Martian reentry environment. This paper will discuss the test facility, especially the arc heater, in more detail. Initial testing involved relatively low concentrations of CO2 combined with N2 for the primary purpose of gathering data to answer two pressing safety concerns. The first being the rate of production of carbon monoxide (CO) within the ejector vacuum system. The main concern was that CO can be flammable and possibly explosive at high enough concentrations and pressures. The hazard control during the development phase involved the use of injecting N2 inside the test chamber diffuser to dilute and reduce the concentration of any and all CO present. A residual gas analyzer (RGA) was used to determine the relative amount of CO in the exhaust gas and provide a conversion rate of CO2 to CO. This paper will discuss in more detail the results of the RGA data and the calculated conversion rate. The second safety concern addressed is the possible formation of hydrogen cyanide (HCN) and cyanide (CN). HCN would primarily be present in the cooling water while the CN would most probably condense onto the interior surfaces of the test chamber. Water samples and wipes of the test chamber surfaces were analyzed by an industrial hygienist for the presence of HCN and CN. His paper will discuss these results in more detail. Throughout this development effort measurements of the CO2:N2 flowfield were made with heat flux and pressure probes and with laser induced fluorescence (LIF) of the atomic oxygen. This paper will discuss these results

DelPapa, Steven V.↗

Delayed signatures of underground nuclear explosions

Radionuclide signals from underground nuclear explosions (UNEs) are strongly influenced by the surrounding hydrogeologic regime. One effect of containment is delay of detonation-produced radioxenon reaching the surface as well as lengthening of its period of detectability compared to uncontained explosions. Using a field-scale tracer experiment, we evaluate important transport properties of a former UNE site. Here, we observe the character of signals at the surface due to the migration of gases from the post-detonation chimney under realistic transport conditions. Background radon signals are found to be highly responsive to cavity pressurization suggesting that large local radon anomalies may be an indicator of a clandestine UNE. Computer simulations, using transport properties obtained from the experiment, track radioxenon isotopes in the chimney and their migration to the surface. They show that the chimney surrounded by a fractured containment regime behaves as a leaky chemical reactor regarding its effect on isotopic evolution introducing a dependence on nuclear yield not previously considered. This evolutionary model for radioxenon isotopes is validated by atmospheric observations of radioxenon from a 2013 UNE in the Democratic People’s Republic of Korea (DPRK). In conclusion, our model produces results similar to isotopic observations with nuclear yields being comparable to seismic estimates.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

TECHNOLOGY GOALS FOR A NEXT GENERATION RADIOXENON MONITORING SYSTEM

The Swedish Automated/Unattended Noble Gas Analyzer (SAUNA) is a nuclear explosion monitoring technology that was developed to provide continuous field measurement of radioxenon gas escaping from an underground nuclear detonation. This capability is a key to the verification of the Comprehensive nuclear Test Ban Treaty (CTBT). While the SAUNA technology has demonstrated success in the field, a decade of operation primarily in the International Noble Gas Experiment (INGE) has yielded areas for improvement in operations and verification. These opportunities include measurement sensitivity, sample throughput time, system uptime, and data availability. Increasing measurement sensitivity allows for finer discrimination between manmade radioxenon signals (from sources such as medical isotope production facilities) and radioxenon signals that result from fission in a nuclear weapon. Measurement sensitivity can be increased with techniques such as halving the sample processing time or increasing the quantity of xenon extracted from the atmosphere. Additionally, improvements in gas processing technology and control system software can improve the uptime and data availability. This paper will discuss the technical requirements as well as the system and operational specifications which we expect to be the groundwork for the next-generation of radioxenon monitoring systems.

Ely, James H.↗

RADIOXENON MEASUREMENTS WITH THE PHOSWATCH DETECTOR SYSTEM

Many of the radioxenon detector systems used in the International Monitoring System and in other applications employ beta/gamma coincidence detection to achieve high sensitivity. In these systems, the coincidence detection is implemented by requiring simultaneous signals from separate beta and gamma detectors. While very sensitive to small amounts of radioxenon, this approach requires careful calibration and gain matching of several detectors and photomultiplier tubes. An alternative approach is the use of a phoswich detector in which beta-gamma coincidences are detected by pulse shape analysis. The phoswich requires only a single photomultiplier tube and thus is easier to set up and calibrate, and can be assembled into a more compact and robust system. In the past, we have developed a COTS detector system, named PhosWatch, which consists of a CsI(Tl)/BC-404 phoswich detector, digital readout electronics, and on-board software to perform the pulse shape analysis. Several units of this system have been manufactured and are now evaluated at several radioxenon research laboratories. In this paper, we will report results from production tests and some of the evaluations, including a side-by-side comparison of a SAUNA detector and a PhosWatch system using atmospheric radioxenon samples. In addition, we will show initial results obtained with a higher speed version of the readout electronics, digitizing at 500 MHz and thus able to better resolve the fast pulses from the BC-404.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗