NASA NTRS2019
During the 2019 summer term, the author worked with a group of four interns to complete the preliminary design of a 2nd stage solid rocket motor for Up Aerospace’s Spyder Launch Vehicle. The Spyder vehicle is a four stage, solid fuel rocket designed as part of collaboration between NASA and Up Aerospace to develop a vehicle capable of delivering a 10 kg, 6U CubeSat into a 350 km, circular, low Earth orbit. As part of the agreement, NASA is tasked with designing high performance 2nd, 3rd, and 4th stages while Up Aerospace will provide the 1st stage, derived from the first stage of the company’s sub-orbital Spaceloft XL vehicle. Previous intern teams have designed the 3rd and 4th stages, which left the preliminary design of the 2nd stage motor to be completed this summer. The purpose of this report is to highlight a trade study which the author conducted to determine the nozzle geometry which would most benefit the performance of the 2nd stage motor. In this study, various nozzle parameters such as throat radius (RSI), expansion ratio, mass and their effects on the Isp and Delta V of the 2nd Stage were investigated. From this study, a nozzle geometry providing the necessary performance was chosen and implemented as part of the preliminary design of the 2nd stage motor. To mature the 2nd stage motor design, a trade space was needed to determine the nozzle configuration which would most benefit the performance of the 2nd stage. The trade space established did not only evaluate different expansion ratios for the same throat radius, but also investigated the possible performance gained from decreasing the throat radius to increase the expansion ratio and Isp capable of being delivered by the nozzle. Decreasing the throat radius would cause the chamber pressure to increase, consequently increasing the case and insulation mass required to safely operate a motor at higher pressures. To account for this factor, accurate estimates of inert mass first needed to be established. After doing so, the effects of varying nozzle expansion ratios, exit half angles, and subsequently length and mass were evaluated against motor and nozzle performance factors such as delta V and Isp. For this study, four throat radii ranging from 1.75” to 2.375” and consequently four different chamber pressures ranging 550 psia to 1200 psia were investigated. BACKGROUND To launch into Low Earth Orbit, a payload needs to be accelerated to the orbital velocity necessary to keep it from falling back to Earth. The change in velocity required between launch and orbital insertion is known as Delta V. The Delta V which a rocket or stage can deliver can be calculated using the Ideal Rocket equation, 𝛥𝑉=−𝑔0∗𝐼𝑠𝑝∗ln(𝑀𝑓𝑀𝑖) (3) Where 𝑔0 is the acceleration due to gravity at the earth’s surface, 𝐼𝑠𝑝 is the specific impulse of the rocket, 𝑀𝑖 is the initial mass of the rocket, and 𝑀𝑓 is the final mass of the rocket after burnout. From preliminary calculations beyond the scope of this paper, it was determined that 30500 ft/s of delta V would be required for a payload to be inserted into a 350 km circular orbit around the Earth. Using the known masses and Isp values of the 1st, 3rd, and 4th stages and equation 3, the delta V of each stage was calculated. The delta V required by the 2nd stage could then be found by taking the difference between the total delta V required and the delta V of the 1st, 3rd, and 4th stages. From this, the required delta V of the 2nd Stage was calculated to be 7340 ft/s. Specific impulse is an efficiency factor of the nozzle which defines the impulse delivered by the motor per unit of propellant weight. The main variables of a nozzle’s specific impulse investigated in this trade were exit cone half angle, throat radius, and expansion ratio which is affected by the throat radius. The expansion ratio, ε, of a nozzle is defined as the ratio between the nozzle exit area and throat area, and can be calculated using the equation, ε=𝑅𝑒𝑥𝑖𝑡2𝑅𝑠𝑖2 (2) Where 𝑅𝑒𝑥𝑖𝑡 is the radius of the nozzle’s exit and 𝑅𝑠𝑖 is the radius of the nozzle’s throat. A larger expansion ratio and smaller exit half angle will increase the Isp of a nozzle by allowing the gas to expand more and by allowing more of the exhaust gas to produce thrust in the direction of the motor’s central axis. A cross section view of the 2nd Stage motor with the major components annotated is provided in figure 1.