Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electrode Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Electrostatic Plasma Accelerator (EPA)

The application of electric propulsion to communications satellites, however, has been limited to the use of hydrazine thrusters with electric heaters for thrust and specific impulse augmentation. These electrothermal thrusters operate at specific impulse levels of approximately 300 s with heater powers of about 500 W. Low power arcjets (1-3 kW) are currently being investigated as a way to increase specific impulse levels to approximately 500 s. Ion propulsion systems can easily produce specific impulses of 3000 s or greater, but have yet to be applied to communications satellites. The reasons most often given for not using ion propulsion systems are their high level of overall complexity, low thrust with long burn times, and the difficulty of integrating the propulsion system into existing commercial spacecraft busses. The Electrostatic Plasma Accelerator (EPA) is a thruster concept which promises specific impulse levels between low power arcjets and those of the ion engine while retaining the relative simplicity of the arcjet. The EPA thruster produces thrust through the electrostatic acceleration of a moderately dense plasma. No accelerating electrodes are used and the specific impulse is a direct function of the applied discharge voltage and the propellant atomic mass.

Brophy, John R.↗

Time varying voltage combustion control and diagnostics sensor

A time-varying voltage is applied to an electrode, or a pair of electrodes, of a sensor installed in a fuel nozzle disposed adjacent the combustion zone of a continuous combustion system, such as of the gas turbine engine type. The time-varying voltage induces a time-varying current in the flame which is measured and used to determine flame capacitance using AC electrical circuit analysis. Flame capacitance is used to accurately determine the position of the flame from the sensor and the fuel/air ratio. The fuel and/or air flow rate (s) is/are then adjusted to provide reduced flame instability problems such as flashback, combustion dynamics and lean blowout, as well as reduced emissions. The time-varying voltage may be an alternating voltage and the time-varying current may be an alternating current.

47 OTHER INSTRUMENTATION↗

Recent Advances in Scalable, High‐Mass Loaded Electrodes for Grid‐Scale Energy Storage

Abstract The increasing electrification of daily life as well as the intermittent characteristic of renewable energy sources require viable solutions for grid‐scale energy storage. Critical considerations for grid storage applications are electrode mass loading and electrode thickness as these features govern battery pack energy density, an important factor in determining manufacturing costs. For this reason, there is increased interest in finding new ways of creating electrodes with high mass loading. In this review, various high‐mass loading fabrication approaches are considered for positive electrode materials used in batteries. The benchmark used for high mass loading is above 20 mg cm −2 , which is higher than the practical limit of conventional tape‐cast electrodes. Several different electrode approaches are described including templating, laser patterning, direct ink writing, and electrodeposition. A variety of materials are covered with the most prominent being LiFe(PO 4 ) (LFP), LiCoO 2 (LCO), and MnO 2 . In research to date, scalable electrochemical performance has been achieved with mass loadings over 100 mg cm −2 . Areal capacities as high as 14.7 mAh cm −2 at 1.82 mA cm −2 have been achieved in non‐aqueous electrolytes and 9.8 mAh cm −2 at 10 mA cm −2 in aqueous electrolytes. These results establish that the mass loading of electrodes can be scaled up without compromising their electrochemical properties.

White, Makena [Department of Materials Science and↗

Examination of the mechanism for the reversible aging behavior at open circuit when changing the operating temperature of (La 0.8 Sr 0.2 ) 0.95 MnO 3 electrodes

The aging behavior of symmetrical cells, consisting of either (La 0.8 Sr 0.2 ) 0.95 MnO 3 (LSM) or La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) electrodes screen printed on either 8 mol% yttria-stabilized zirconia (YSZ) or Ce 0.8 Gd 0.2 O 2 (GDC) electrolyte substrates, is reported as the symmetrical cell is thermally cycled between 700 °C and 800 °C. For LSM, between 700 °C and 850 °C, the polarization resistance exhibits slow increases or decreases with time (on the order of days) after a quick change in temperature. When increasing the temperature, the polarization resistance decreases with time, and when decreasing the temperature, the polarization resistance slowly increases with time. In a previous work, the authors had explained these results with LSM by connecting the testing conditions to literature reports of surface analysis of LSM thin films which demonstrated a change in the amount of surface cation segregation as a function of temperature. In this work, TEM/EDS/XPS analysis of dense LSM pellets thermally cycled under the same conditions as the symmetrical cells does not indicate any significant reversible change in the surface composition of the LSM pellet between 700 °C and 800 °C. An alternative hypothesis is proposed to explain the relationship between polarization resistance and the LSM cation/anion vacancy concentrations controlled by the Schottky reaction. The timescale of aging behavior is related to the time necessary for the cations to move to or from the LSM surface to adjust to the new equilibrium at each temperature. Furthermore, the relevance in understanding the mechanism behind the aging behavior is emphasized with respect to fuel cell sample/stack modeling as well as to proper testing procedures for reaching reliable conclusions when comparing different electrode samples.

42 ENGINEERING↗

Nitrogenase Inspired Peptide-Functionalized Catalyst for Efficient, Emission-Free Ammonia Production

Ammonia production is one of the most important industrial processes in the world, as the major component of fertilizer to sustain higher food production. It is also one of the most energy intensive and carbon intensive chemical processes worldwide, primarily due to the steam methane reforming step to produce hydrogen for the reaction. Currently, ammonia is produced via the Haber Bosch process, which requires high temperature and pressure, and has low equilibrium efficiency. Due to these reaction conditions, the process is most economical at extremely large scale (100,000s of tons per day). In order to enable more distributed production scales which better match with renewable energy input and sustainable reactant sources, alternative methods of ammonia synthesis are needed, which scale more effectively and economically. One such approach is electrochemical synthesis based on ion exchange membrane cells. Peptide templating to form catalyst nanoparticles of controlled size, combined with peptide surface adsorbtion to model the nitrogenase active site, was used to develop novel catalyst materials and deposit them on electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

III-nitride transistor with trench gate

A transistor includes a stack of III-nitride semiconductor layers, the stack having a frontside and a backside, a source electrode in contact with the frontside of the stack, a drain electrode in contact with the backside of the stack, a trench extending through a portion of the stack, the trench having a sidewall, and a gate structure formed in the trench, including an AlN layer formed on the sidewall of the trench, an insulating cap layer formed on the AlN layer, and a gate electrode formed on the insulator cap layer and covering the sidewall of the trench.

42 ENGINEERING↗

Pore size engineering applied to the design of separators for nickel-hydrogen cells and batteries

Pore size engineering in starved alkaline multiplate cells involves adopting techniques to widen the volume tolerance of individual cells. Separators with appropriate pore size distributions and wettability characteristics (capillary pressure considerations) to have wider volume tolerances and an ability to resist dimensional changes in the electrodes were designed. The separators studied for potential use in nickel-hydrogen cells consist of polymeric membranes as well as inorganic microporous mats. In addition to standard measurements, the resistance and distribution of electrolyte as a function of total cell electrolyte content were determined. New composite separators consisting of fibers, particles and/or binders deposited on Zircar cloth were developed in order to engineer the proper capillary pressure characteristics in the separator. These asymmetric separators were prepared from a variety of fibers, particles and binders.

Abbey, K. M.↗

Pore size engineering applied to the design of separators for nickel-hydrogen cells and batteries

Pore size engineering in starved alkaline multiplate cells involves adopting techniques to widen the volume tolerance of individual cells. Separators with appropriate pore size distributions and wettability characteristics (capillary pressure considerations) to have wider volume tolerances and an ability to resist dimensional changes in the electrodes were designed. The separators studied for potential use in nickel-hydrogen cells consist of polymeric membranes as well as inorganic microporous mats. In addition to standard measurements, the resistance and distribution of electrolyte as a function of total cell electrolyte content were determined. New composite separators consisting of fibers, particles and/or binders deposited on Zircar cloth were developed in order to engineer the proper capillary pressure characteristics in the separator. These asymmetric separators were prepared from a variety of fibers, particles and binders. Previously announced in STAR as N83-24571

Abbey, K. M.↗

Axial Ge/Si nanowire heterostructure tunnel FETs.

Axial Ge/Si heterostructure nanowires (NWs) allow energy band-edge engineering along the axis of the NW, which is the charge transport direction, and the realization of asymmetric devices for novel device architectures. This work reports on two significant advances in the area of heterostructure NWs and tunnel FETs: (i) the realization of 100% compositionally modulated Si/Ge axial heterostructure NWs with lengths suitable for device fabrication and (ii) the design and implementation of Schottky barrier tunnel FETs on these NWs for high-on currents and suppressed ambipolar behavior. Initial prototype devices with 10 nm PECVD SiN{sub x} gate dielectric resulted in a very high current drive in excess of 100 {micro}A/{micro}m (I/{pi}D) and 10{sup 5} I{sub on}/I{sub off} ratios. Prior work on the synthesis of Ge/Si axial NW heterostructures through the VLS mechanism have resulted in axial Si/Si{sub 1-x}Ge{sub x} NW heterostructures with x{sub max} {approx} 0.3, and more recently 100% composition modulation was achieved with a solid growth catalyst. In this latter case, the thickness of the heterostructure cannot exceed few atomic layers due to the slow axial growth rate and concurrent radial deposition on the NW sidewalls leading to a mixture of axial and radial deposition, which imposes a big challenge for fabricating useful devices form these NWs in the near future. Here, we report the VLS growth of 100% doping and composition modulated axial Ge/Si heterostructure NWs with lengths appropriate for device fabrication by devising a growth procedure that eliminates Au diffusion on the NW sidewalls and minimizes random kinking in the heterostructure NWs as deduced from detailed microscopy analysis. Fig. 1 a shows a cross-sectional SEM image of epitaxial Ge/Si axial NW heterostructures grown on a Ge(111) surface. The interface abruptness in these Ge/Si heterostructure NWs is of the order of the NW diameter. Some of these NWs develop a crystallographic kink that is {approx}20{sup o} off the <111> axis at about 300 nm away from the Ge/Si interface. This provides a natural marker for placing the gate contact electrodes and gate metal at appropriate location for desired high-on current and reduced ambipolarity as shown in Fig. 2. The 1D heterostructures allow band-edge engineering in the transport direction, not easily accessible in planar devices, providing an additional degree of freedom for designing tunnel FETs (TFETs). For instance, a Ge tunnel source can be used for efficient electron/hole tunneling and a Si drain can be used for reduced back-tunneling and ambipolar behavior. Interface abruptness on the other hand (particularly for doping) imposes challenges in these structures and others for realizing high performance TFETs in p-i-n junctions. Since the metal-semiconductor contacts provide a sharp interface with band-edge control, we use properly designed Schottky contacts (aided by 3D Silvaco simulations) as the tunnel barriers both at the source and drain and utilize the asymmetry in the Ge/Si channel bandgap to reduce ambipolar transport behavior generally observed in TFETs. Fig. 3 shows the room-temperature transfer curves of a Ge/Si heterostructure TFET (H-TFET) for different V{sub DS} values showing a maximum on-current of {approx}7 {micro}A, {approx}170 mV/decade inverse subthreshold slope and 5 orders of magnitude I{sub on}/I{sub off} ratios for all V{sub DS} biases considered here. This high on-current value is {approx}1750 X higher than that obtained with Si p-i-n{sup +} NW TFETs and {approx}35 X higher than that obtained with CNT TFET. The I{sub on}/I{sub off} ratio and inverse subthreshold slope compare favorably to that of Si {approx} 10{sup 3} I{sub on}/I{sub off} and {approx} 800 mV/decade SS{sup -1} but lags behind those of CNT TFET due to poor PECVD nitride gate oxide quality ({var_epsilon}{sub r} {approx} 3-4). The asymmetry in the Schottky barrier heights used here eliminates the stringent requirements of abrupt doped interfaces used in p-i-n based TFETs, which is hard to achieve both in thin-film and in NW growth. These initial promising results are expected to be further improved by using a high-k gate dielectric.

36 MATERIALS SCIENCE↗

Tunneling Barrier-Integrated Gold Nanofilms for Negative Strain Gauging with Near-Zero Energy Consumption

Wireless strain sensors with minimal power needs are essential for long-term monitoring in energy-limited environments. We present a soft tunneling barrier-integrated gold thin film for negative strain sensing with near-zero energy consumption. The device features a strain-induced transition from an insulating to a metallic state, increasing conductivity by 9 orders of magnitude under a controlled strain. It consists of Au-PDMS-Au nanofilm layers, where the Au structures are near the percolation threshold and the PDMS layer acts as a tunneling barrier. Under strain, thinning due to the Poisson effect lowers the barrier’s potential height, enabling electron tunneling and forming an electrical path. Further, with a standby power consumption of ~10 –5 mW over 10 6 times lower than conventional sensors (~12.5 mW), this device is ideal for real-time, long-term stationary structural monitoring in multiple locations.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Autonomous Multistate Nanoencoding Using Combinatorial Ferroelectric Closure Domains in BiFeO 3

Recent advances in ferroic materials have identified topological defects as promising candidates for enabling additional functionalities in future electronic systems. The generation of stable and customizable polar topologies is needed to achieve multistates that enable beyond-binary device architectures. Here, in this study, we show how to autonomously pattern on-demand highly tunable striped closure domains in pristine rhombohedral-phase BiFeO 3 thin films through precise scanning of a biased atomic force microscopy tip along carefully designed paths. By employing this strategy, we generate and manipulate closed-loop structures with high spatial resolution in an automated manner, allowing the creation of highly tunable and intricate topological domain structures that exhibit distinct polarization configurations without the need for electrode deposition or complex heterostructure growth. As a proof-of-concept for ferroelectric beyond-binary memory devices, we use such topological domains as multistates, engineering an alphabet and automating the symbolic writing/reading process using autonomous microscopy. The resulting information density is compared with that of current commercially available memory devices, demonstrating the potential of ferroelectric topological domains for multistate information storage applications.

BiFeO3↗

High-entropy electrolytes for practical lithium metal batteries

Electrolyte engineering is crucial for improving battery performance, particularly for lithium metal batteries. Recent advances in electrolytes have greatly improved cyclability by enhancing electrochemical stability at the electrode interfaces, but concurrently achieving high ionic conductivity has remained challenging. Here we report an electrolyte design strategy for enhanced lithium metal batteries by increasing the molecular diversity in electrolytes, which essentially leads to high entropy electrolytes (HEEs). We find that in weakly solvating electrolytes, the entropy effect reduces ion clustering while preserving the characteristic anion-rich solvation structures, which is characterized by synchrotron-based X-ray scattering and molecular dynamics simulations. Electrolytes with smaller- sized clusters exhibit a 2-fold improvement in ionic conductivity compared to conventional weakly- solvating electrolytes, enabling stable cycling at high current densities up to 2C (6.2 mA cm -2 ) in anode- free LiNi 0.6 Mn 0.2 Co 0.2 (NMC622)||Cu pouch cells. In conclusion, the efficacy of the design strategy is verified by performance improvements in three disparate weakly solvating electrolyte systems.

25 ENERGY STORAGE↗

Characterization of FeCl 3 Intercalation Doped CVD Few-Layer Graphene

Historically, intercalation doping has been theoretically and experimentally studied on Chemical Vapor Deposition (CVD) synthesized few-layer graphene. Density Functional Theory calculations identified FeCl 3 as a good dopant to reduce the sheet resistance of few-layer graphene. A simple vapor transfer approach is employed to dope graphene. The successful doping is confirmed by the Raman spectra as well as electrical measurements. After doping, graphene shows p-type conducting behavior and its conductance is significantly enhanced compared with that of undoped graphene. 3-layer graphene exhibited a sheet resistance of 40 Ω/$\square$, while 4-layer graphene has even smaller sheet resistance of 20 Ω/$\square$, with transmittance ≥ 90% for both cases. which offer the best combination of sheet resistance and transmittance among all previously reported transparent conductors.

42 ENGINEERING↗

Development of automatic through-insulation welding for microelectric interconnections

The capability to automatically route, remove insulation from, and weld small-diameter solid conductor wire is presented. This would facilitate the economical small-quantity production of complex miniature electronic assemblies. An engineering model of equipment having this capability was developed and evaluated. Whereas early work in the use of welded magnet wire interconnections was concentrated on opposed electrode systems, and generally used heat to melt the wire insulation, the present method is based on a concentric electrode system and a wire feed system which splits the insulation by application of pressure prior to welding. The work deals with the design, fabrication, and evaluation testing of an improved version of this concentric electrode system. Two different approaches to feeding the wire to the concentric electrodes were investigated. It was concluded that the process is feasible for the interconnection of complex miniature electronic assemblies.

Arnett, J. C.↗

Increased capabilities of the Langley Mach 7 Scramjet Test Facility

An experimental research program which explored the potential for expanding the operating range of NASA Langley's Mach 7 Scramjet Test Facility is described. The facility uses electric arc-heated air as the test gas and is configured for testing airframe-integrated scramjet engine models at conditions duplicating flight velocities and temperatures. Previous scramjet testing in this facility was limited to a single simulated flight condition of Mach 6.9 at 115,300 ft. altitude. The present arc heater research demonstrated that the facility can be used for scramjet testing at simulated flight conditions from Mach 4 (at altitudes from 77,000 to 114,000 ft.) to Mach 7 (at altitudes from 108,000 to 149,000 ft.). Flow quality was established from the uniformity of measured total temperature profiles. In addition, nitrogen oxide levels in the test stream were determined for relating engine test data to expected flight performance. The test frequency and reliability of the facility were also improved by a novel redesign of the heater downstream electrode and by defining limits for stable arc operation.

Thomas, S. R.↗