Search NASA⌕ Search

SEARCH · Search NASA

Results for “HOVERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Recommendations for ground effects research for V/STOL and STOL aircraft and associated equipment for large scale testing

The current understanding of the effects of ground proximity on V/STOL and STOL aircraft is reviewd. Areas covered include (1) single jet suckdown in hover, (2) fountain effects on multijet configurations, (3) STOL ground effects including the effect of the ground vortex flow field, (4) downwash at the tail, and (5) hot gas ingestion in both hover and STOL operation. The equipment needed for large scale testing to extend the state of the art is reviewed and developments in three areas are recommended as follows: (1) improve methods for simulating the engine exhaust and inlet flows; (2) develop a model support system that can simulate realistic rates of climb and descent as well as steady height operation; and (3) develop a blowing BLC ground board as an alternative to a moving belt ground board to properly simulate the flow on the ground.

Kuhn, Richard E.↗
NASA NTRS1988

Flight testing a V/STOL aircraft to identify a full-envelope aerodynamic model

Flight-test techniques are being used to generate a data base for identification of a full-envelope aerodynamic model of a V/STOL fighter aircraft, the YAV-8B Harrier. The flight envelope to be modeled includes hover, transition to conventional flight and back to hover, STOL operation, and normal cruise. Standard V/STOL procedures such as vertical takeoff and landings, and short takeoff and landings are used to gather data in the powered-lift flight regime. Long (3 to 5 min) maneuvers which include a variety of input types are used to obtain large-amplitude control and response excitations. The aircraft is under continuous radar tracking; a laser tracker is used for V/STOL operations near the ground. Tracking data are used with state-estimation techniques to check data consistency and to derive unmeasured variables, for example, angular accelerations. A propulsion model of the YAV-8B's engine and reaction control system is used to isolate aerodynamic forces and moments for model identification. Representative V/STOL flight data are presented. The processing of a typical short takeoff and slow landing maneuver is illustrated.

Mcnally, B. David↗
NASA NTRS1987

Prediction of high-speed rotor noise with a Kirchhoff formula

A new methodology has been developed to predict the impulsive noise generated by a transonic rotor blade. The formulation uses a full-potential finite-difference method to obtain the pressure field close to the blade. A Kirchhoff integral formulation is then used to extend these finite-difference results into the far-field. This Kirchhoff formula is written in a blade-fixed coordinate system. It requires initial data across a plane at the sonic radius. This data is provided by the finite-difference solution. Acoustic pressure predictions show excellent agreement with hover experimental data for two hover cases of 0.88 and 0.90 tip Mach number, the latter of which has delocalized transonic flow. These results represent the first successful prediction technique for peak pressure amplitudes using a computational code.

Purcell, Timothy W.↗
NASA NTRS1987

Geometrical acoustics and transonic helicopter sound

A new method is presented for predicting the impulsive noise generated by a transonic rotor blade. The method is a combined approach involving computational fluid dynamics and geometrical acoustics. A full-potential finite-difference method is used to obtain the pressure field close to the blade. A Kirchhoff integral formulation is then used to extend these finite-difference results into the far field. This Kirchhoff formula is based on geometrical acoustics approximations. It requires initial data across a plane at the sonic radius in a blade-fixed coordinate system. This data is provided by the finite-difference solution. Acoustic pressure predictions show good agreement with hover experimental data for cases with hover tip Mach numbers of 0.88 through 0.96. The cases above 0.92 tip Mach number are dominated by non-linear transonic effects seen as strong shocks on and off the blade tip. This paper gives the first successful predictions of far-field acoustic pressures for high-speed impulsive noise over a range of Mach numbers after delocalization.

Isom, Morris↗
NASA NTRS1988

Numerical simulation of helicopter multi-bladed rotor flow

A numerical method for solving the Euler equations for multiblade rotors has been developed. The computed results, including one nonlifting forward-flight and several lifting hovering cases, are compared with experimental data. For forward-flight case, the unsteady growth and decay of the shock agree well with experimental results. For hovering case, at low and moderate transonic tip speed, the results show good agreement with experimental data in the tip region. The near-wake effects can be captured without wake modeling.

Chen, C. L.↗
NASA NTRS1987

Aeroelastic stability of bearingless rotors in forward flight

The finite element method was used to determine the dynamic stability of bearingless rotor blades (BR) in forward flight. The analysis was applied to four different BR configurations and the results were correlated with experimental data. The analysis was correlated with hover lag mode stability data for a simple three-blade BR rotor tested in various pitch link configurations. In addition, a more advanced BR which includes precone, blade twist, blade sweep, and a lag shear restraint is analyzed and compared to experimental data in both hover and forward flight.

Dull, Andrew L.↗
NASA NTRS1988

Flight testing a V/STOL aircraft to identify a full-envelope aerodynamic model

Flight-test techniques are being used to generate a data base for identification of a full-envelope aerodynamic model of a V/STOL fighter aircraft, the YAV-8B Harrier. The flight envelope to be modeled includes hover, transition to conventionally flight and back to hover, STOL operation, and normal cruise. Standard V/STOL operation, and normal cruise. Standard V/STOL procedures such as vertical takeoff and landings, and short takeoff and landings are used to gather data in the powered-lift flight regime. Long (3-5-min) maneuvers which include a variety of input types are used to obtain large-amplitude control and response excitations. The aircraft is under continuous radar tracking; a laser tracker is used for V/STOL operations near the ground. Tracking data are used with state-estimation techniques to check data consistency and to derive unmeasured variables, for example, angular accelerations. A propulsion model of the YAV-8B's engine and reaction control system is used to isolate aerodynamic forces and moments for model identification. Representative V/STOL flight data are presented. The processing of a typical short-takeoff and slow-landing maneuver is illustrated.

Mcnally, B. David↗
NASA NTRS1988

The effect of perspective displays on altitude and stability control in simulated rotary wing flight

The effect of perspective displays on flight performance is investigated using two simulation experiments. In the first, a perspective grid display was superimposed on computer-generated terrain and subjects attempted to maintain their initial attitude in a simulated hover using terrain and/or one of four grid patterns. Horizontal lines produced the best attitude control performance. In the second experiment, a square grid was studied in combination with various visual display configurations and grid attachment conditions. It was found that performance with the panel-mounted display was significantly worse than with the out-the-window or helmet-mounted displays. The results suggested that the partial grid attachment condition improved hovering performance with the panel-mounted display.

O'Donnell, K. A.↗
NASA NTRS1988

LANDER program manual: A lunar ascent and descent simulation

LANDER is a computer program used to predict the trajectory and flight performance of a spacecraft ascending or descending between a low lunar orbit of 15 to 500 nautical miles (nm) and the lunar surface. It is a three degree-of-freedom simulation which is used to analyze the translational motion of the vehicle during descent. Attitude dynamics and rotational motion are not considered. The program can be used to simulate either an ascent from the Moon or a descent to the Moon. For an ascent, the spacecraft is initialized at the lunar surface and accelerates vertically away from the ground at full thrust. When the local velocity becomes 30 ft/s, the vehicle turns downrange with a pitch-over maneuver and proceeds to fly a gravity turn until Main Engine Cutoff (MECO). The spacecraft then coasts until it reaches the requested holding orbit where it performs an orbital insertion burn. During a descent simulation, the lander begins in the holding orbit and performs a deorbit burn. It then coasts to pericynthion, where it reignites its engines and begins a gravity turn descent. When the local horizontal velocity becomes zero, the lander pitches up to a vertical orientation and begins to hover in search of a landing site. The lander hovers for a period of time specified by the user, and then lands.

Source record↗
NASA NTRS1989

Flap-lag stability data for a small-scale isolated hingeless rotor in forward flight

An isolated, hingeless rotor with discrete flap and lead-lag flexures and relatively rigid blades was tested in the Aeroflightdynamics Directorate's 7- by 10-Foot Wind Tunnel. The lead-lag stability of a structurally simple rotor configuration in forward flight was determined. The model tested had no cyclic pitch control, and was therefore operated untrimmed at several collective pitch angles, at shaft angles from 0 deg to -20 deg, and at advance ratios as high as 0.55. Two inplane natural frequencies, 0.61/rev and 0.72/rev, were tested for configuration both with and without structural flap lag coupling. Concomitant hover testing of the model was also conducted. Representative plots of the frequency and damping data are presented to show general trends, and complete tabular data and model properties information are included for use in detailed correlation exercises. The most prominent feature of the forward flight data is an abrupt increase in damping with advance ratio at certain high-speed, high shaft-angle conditions, with high flapping loads. The hover data are consistent with previous experimental and theoretical results for hingeless rotors without kinematic couplings. Overall, the data quality is very good and the data are expected to be useful in the development and validation of rotor aeroelastic stability analyses.

Mcnulty, Michael J.↗
NASA NTRS1988

An entropy and viscosity corrected potential method for rotor performance prediction

An unsteady Full-Potential Rotor code (FPR) has been enhanced with modifications directed at improving its drag prediction capability. The shock generated entropy has been included to provide solutions comparable to the Euler equations. A weakly interacted integral boundary layer has also been coupled to FPR in order to estimate skin-friction drag. Pressure distributions, shock positions, and drag comparisons are made with various data sets derived from two-dimensional airfoil, hovering, and advancing high speed rotor tests. In all these comparisons, the effect of the nonisentropic modification improves (i.e., weakens) the shock strength and wave drag. In addition, the boundary layer method yields reasonable estimates of skin-friction drag. Airfoil drag and hover torque data comparisons are excellent, as are predicted shock strength and positions for a high speed advancing rotor.

Bridgeman, John O.↗
NASA NTRS1960

Ground Effect for Lifting Rotors in Forward Flight

A theoretical analysis indicates that, for rotors, ground effect decreases rapidly with increases in either height above the ground or forward speed. The decrease with height above the ground in forward flights is greater than that in hovering. The major part of the decrease in ground effect with forward speed occurs at speeds less than 1.5 times the hovering mean induced velocity. Consequently, the total induced velocity at the rotor center increases rather than decreases when a helicopter gathers speed at low height above the ground.

Heyson, Harry H.↗
NASA NTRS1990

Aerodynamic Performance of a 0.27-Scale Model of an AH-64 Helicopter with Baseline and Alternate Rotor Blade Sets

Performance of a 27 percent scale model rotor designed for the AH-64 helicopter (alternate rotor) was measured in hover and forward flight and compared against and AH-64 baseline rotor model. Thrust, rotor tip Mach number, advance ratio, and ground proximity were varied. In hover, at a nominal thrust coefficient of 0.0064, the power savings was about 6.4 percent for the alternate rotor compared to the baseline. The corresponding thrust increase at this condition was approx. 4.5 percent which represents an equivalent full scale increase in lift capability of about 660 lbs. Comparable results were noted in forward flight except for the high thrust, high speed cases investigated where the baseline rotor was slightly superior. Reduced performance at the higher thrusts and speeds was likely due to Reynolds number effects and blade elasticity differences.

Kelley, Henry L.↗
NASA NTRS1989

A flight-test methodology for identification of an aerodynamic model for a V/STOL aircraft

This paper describes a flight-test methodology for developing a data base to be used to identify an aerodynamic model of a V/STOL fighter aircraft. The aircraft serves as a test bed at NASA Ames for ongoing research in advanced V/STOL control and display concepts. The flight envelope to be modeled includes hover, transition to conventional flight and back to hover, STOL operation, and normal cruise. Although the aerodynamic model is highly nonlinear, it has been formulated to be linear in the parameters to be identified. Motivation for the flight-test methodology advocated in this paper is based on the choice of a linear least-squares method for model identification. The paper covers elements of the methodology from maneuver design to the completed data base. Major emphasis is placed on the use of state estimation with tracking data to ensure consistency among maneuver variables prior to their entry into the data base. The design and processing of a typical maneuver are illustrated.

Bach, R. E., Jr.↗
NASA NTRS1990

An experimental and analytical investigation of isolated rotor flap-lag stability in forward flight

The flap-lag stability of an isolated hingeless rotor is investigated, both experimentally and analytically, in hover and in forward flight. The effects of forward flight aerodynamics on regressing lead-lag mode stability are the focus of the investigation. The soft-inplane, three-bladed, isolated model rotor was operated untrimmed at advance ratios from hover to 0.55 and at shaft angles as high as 20 deg. The experimental data base includes forward flight damping data for two lead-lag natural frequencies, for three values of collective pitch, and for both zero and full-lag structural coupling. With the aid of computerized symbolic manipulation, a rigid-blade lag-flap model analysis was developed to calculate the Floquent eigenvalues and to identify the modes. Good correlation is shown for some cases, but other cases show large discrepancies between the theory and experiment.

Gaonkar, Gopal H.↗
NASA NTRS1990

A computational study of the impingement region of an unsteady subsonic jet

Vertical/Short Take-Off and Landing (V/STOL) aircraft may encounter operating difficulties while hovering near the ground. Lift loss, hot gas and debris ingestion, and landing surface damage are some of the potential problems which can result from the interaction of the propulsive jets with the airframe and ground. The purpose of the present work is to develop a detailed understanding of a flowfield, a jet exiting from a flat plate impacting a ground plane, that contains much of the essential physics of the complex flows encountered by V/STOL aircraft in hover. To achieve this, a high-resolution time-accurate numerical simulation of the impinging jet flow was performed. The numerical simulation is based on the solution of the laminar compressible Navier-Stokes equations using the Beam-Warming algorithm. Complex start-up and periodic jet and jet-induced vortex structures were captured, including the formation of primary and secondary jet-induced vortices and wall-jet separation. The formation and development of these phenomena are supported by experimental measurements and smoke visualization. Results are compared with appropriate experiments.

Jalamani, Zakaria A.↗
NASA NTRS1988

CFD and transonic helicopter sound

A computational method which predicts far-field impulsive noise from a transonic motor blade is demonstrated. This method couples near-field results from a full-potential finite-difference method with a new Kirchhoff integral formulation to extend the finite-difference results into the acoustic far-field. This Kirchhoff formula is written in a blade-fixed coordinate system. It requires initial data from the potential code on a plane at the sonic radius. A recent hovering rotor experiment is described where accurate pressure measurements were recorded on the sonic cylinder and at 2 and 3 radii. The potential code prediction of sonic cylinder pressures is excellent. Acoustic far-field pressure predictions show good agreement with hover experimental data over the range of speeds from 0.85 to 0.92 tip Mach number, the latter of which have delocalized transonic flow. These results are some of the first successful predictions for peak pressure amplitudes using a computational code.

Purcell, Timothy W.↗
NASA NTRS1990

Flight control design considerations for STOVL powered-lift flight

Short Takeoff Vertical Landing (STOVL) aircraft rely on the propulsion system for the lift and control functions during slow speed flight. The propulsion system provides the entire lifting force and all of the control power for hovering flight at zero airspeed. STOVL designs such as the General Dynamics E-7D ejector configuration incorporate an integrated flight/propulsion control system to manage the aerodynamic and propulsive-lift control effectors and to reduce the pilot's workload for powered-lift flight. Desired flying qualities characteristics are implemented through the utilization of an explicit model following flight control system. With the model following control system, the pilot commands the desired response (e.g., throttle commands vertical velocity in hover, instead of power lever angle). Design considerations for developing a multivariable model-following flight control system are presented in this paper. When the regulator gains are defined in terms of generalized controls, the design problem becomes how to best transform the generalized controls to aerodynamic control surface, thrust and thrust vectoring commands.

Vincent, James H.↗