Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYDROGEN ATOM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Atomic Layer Deposition for Enhanced Reactivity, Stability, and Sulfur Tolerance of Hydrogenation Catalysts

NREL is located in the beautiful scenic Colorado, but it has a dirty secret. It is among one the top 10 worst U.S. cities for hazardous air pollution, particularly in Denver. The Denver metro area has been out of compliance with EPA's limits on ozone pollution for decades and it's gotten so bad that at the end of last year the EPA moved our designation from moderate non-obtainment to serious non-obtainment. There's a lot of work that needs to be done in Denver and around the world to reduce air pollution in urban areas.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Single-atom molybdenum doping induces nickel oxide-to-hydroxide transformation for enhanced alkaline hydrogen evolution

NiMoO x compounds are widely regarded as among the most efficient non-noble metal catalysts for the hydrogen evolution reaction (HER). Nevertheless, understanding the structural evolution under in situ conditions and further enhancing their performance remain key challenges. Herein, we report that single-atom Mo doping in NiO significantly enhances its HER activity, reducing the overpotential to 131 mV at 10 mA cm −2 compared to undoped NiO. In situ X-ray absorption spectroscopy and Raman spectroscopy reveal that under catalytic conditions, Mo single atoms remain structurally stable, while Ni 2+ species in NiO are converted to Ni(OH) 2 in alkaline media under the applied working potential for HER. Notably, this transformation is absent in undoped NiO, indicating that Mo doping promotes the formation of active Ni(OH) 2 sites, which, in turn, accelerate the rate-limiting water dissociation step. These findings provide critical mechanistic insights into the structural evolution of NiMoO x during alkaline HER and highlight the importance of in situ studies in the development of highly efficient catalysts.

58 GEOSCIENCES↗
DOE OSTI2023

Quadruple Langmuir probe characterization of different fuel gases in a plasma deflagration accelerator

Astrophysical flows may be studied by reproducing similar conditions using a coaxial plasma accelerator operating in the deflagration regime (or plasma deflagration accelerator). This allows for the recreation and investigation of dynamics present in complex highly coupled plasma systems at the laboratory scale. Here we report on measurements of the plasma density, temperature, plasma potential and velocity found using a quadruple Langmuir probe (QLP) on such a deflagration accelerator in the form of the Stanford Coaxial High ENerGy (CHENG) device operating with multiple gases – specifically argon, nitrogen and hydrogen. Experiments show a general decrease in bulk plasma velocity with gas atomic mass from upwards of 120 km s –1 with hydrogen to less than 30 km s –1 with argon. There was an accompanying increase in peak plasma density with increasing atomic mass from ~3 × 10 20 m –3 with hydrogen to ~1.5 × 10 21 m –3 with argon. It was found that the momentum flux and internal energy density also generally increase with atomic mass while the particle flux is constant between shots. Further investigation is needed to understand these correlations and the underlying physics. Lastly, comparisons with scaling laws show that while the CHENG device may be operated in such a way as to simulate the effects of bulk solar wind movement, it may not properly capture the thermal effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Single‐Atomic Site Catalyst with Heme Enzymes‐Like Active Sites for Electrochemical Sensing of Hydrogen Peroxide

Abstract Heme enzymes, with the pentacoordinate heme iron active sites, possess high catalytic activity and selectivity in biosensing applications. However, they are still subject to limited catalytic stability in the complex environment and high cost for broad applications in electrochemical sensing. It is meaningful to develop a novel substitute that has a similar structure to some heme enzymes and mimics their enzyme activities. One emerging strategy is to design the Fe‐N‐C based single‐atomic site catalysts (SASCs). The obtained atomically dispersed Fe‐N x active sites can mimic the active sites of heme enzymes effectively. In this work, a SASC (Fe‐SASC/NW) is synthesized by doping single iron atoms in polypyrrole (PPy) derived carbon nanowire via a zinc‐atom‐assisted method. The proposed Fe‐SASC/NW shows high heme enzyme‐like catalytic performance for hydrogen peroxide (H 2 O 2 ) with a specific activity of 42.8 U mg −1 . An electrochemical sensor based on Fe‐SASC/NW is developed for the detection of H 2 O 2 . This sensor exhibits a wide detection concentration range from 5.0 × 10 −10 m to 0.5 m and an excellent limit of detection (LOD) of 46.35 × 10 −9 m . Such excellent catalytic activity and electrochemical sensing sensitivity are attributed to the isolated Fe‐N x active sites and their structural similarity with natural metalloproteases.

Ding, Shichao↗
DOE OSTI2025

Bottom-up fabrication of scalable room-temperature diamond quantum computing and sensing technologies

The nitrogen-vacancy (NV) centre in diamond is a premier solid-state defect for quantum information processing and metrology. An integrated diamond quantum device harnesses the collective properties of multiple NV centres, enabling room-temperature quantum computing and sensing. While large-scale devices are poised to fill an important gap in the burgeoning quantum technology landscape, their practical realisation has not been achieved using current top-down fabrication techniques such as ion implantation. Consequently, this necessitates the development of a bottom-up fabrication technique, which is scalable, deterministic, and possesses atomic-scale precision. Informed by existing methods for fabricating phosphorous defect qubits in silicon, we envision a hydrogen depassivation lithography technique for atomically-precise manufacturing of nitrogen-vacancy centres in diamond. This perspective article outlines a viable multi-step procedure for realising scalable fabrication of diamond quantum devices and identifies the key challenges in its development.

CVD↗
DOE OSTI2021

Economic Dispatch Model of Nuclear High-Temperature Reactor with Hydrogen Cogeneration in Electricity Market

Hydrogen produced without carbon emissions could be a useful fuel as nations look to decarbonize their electricity, transport, and industry sectors. Using the iodine–sulfur (IS) cycle coupled with a nuclear heat source is one method for producing hydrogen without the use of fossil fuels. An economic dispatch model was developed for a nuclear-driven IS system to determine hydrogen sale prices that would make such a system profitable. The system studied is the HTTR-GT/H2, a design for power and hydrogen cogeneration at the Japan Atomic Energy Agency’s High Temperature Engineering Test Reactor. This study focuses on the development of the economic model and the role that input data plays in the final calculated values. Using a historical price duration curve shows that the levelized cost of hydrogen (LCOH) or breakeven sale price of hydrogen would need to be 98.1 JPY/m3 or greater. Synthetic time histories were also used and found the LCOH to be 67.5 JPY/m3. The price duration input was found to have a significant effect on the LCOH. As such, great care should be used in these economic dispatch analyses to select reasonable input assumptions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Iron Single‐Atom Catalyzed N‐Alkylation of Amines with Alcohols via Solvent‐Free Borrowing Hydrogen Strategy

Abstract Industrial hydrogenation is a pivotal process in chemical synthesis. However, it has significant drawbacks, including high cost, safety risks associated with the use of molecular hydrogen gas, and substantial energy demands due to the need for elevated temperatures and pressures to achieve satisfactory yields. The borrowing hydrogen synthesis, which enables the transfer of hydrogen between molecules, offers a promising approach for green, one‐pot synthesis of industrially important chemicals and intermediates. Despite its potential, the broad application remains limited due to the reliance on toxic solvents, expensive noble metal catalysts, and the still restricted efficiency and substrate scope. In this study, the first solvent‐free strategy for theN‐alkylation of amines with alcohols is presented, employing an N‐doped graphene‐supported Fe single‐atom catalyst (Fe SA @N‐G; 1.06 wt.%). This approach achieves superior conversion and selectivity (up to 99%) along with record values for turnover number (TON, 1032.7) and turnover frequency (TOF, 413.1 h -1 ) for the coupling reaction of aniline with benzyl alcohol, surpassing all previously reported catalysts. DFT calculations, combined with experimental data, elucidated the reaction mechanism and identified the Fe 1 (III)‐N 4 active site participating in Fe‐H hydride transfer and containing two pyrrolic and two pyridinic nitrogens bound to the Fe center. The developed technology is further supported by the catalyst's excellent scalability, reusability, and performance under continuous‐flow conditions. Additionally, the exceptional efficiency of the single‐atom catalyst is demonstrated across more than 50 substrates, including reactions involving both aliphatic and aromatic amines with aliphatic and aromatic alcohols. The industrial applicability of this technology is validated through the synthesis of pharmaceutically relevant compounds, including stimulant drugs, antihistamines, and pharmaceutical intermediates.

Chemistry↗
DOE OSTI2025

Effects of high-pressure hydrogen exposure on filler-elastomer adhesion

Elastomers are known to gain enhanced mechanical properties through compounding with nanosized filler particles such as silica or carbon black. Filler dispersion and filler-polymer interfacial strength are key contributing factors to this improvement. The interfacial strength is critical to part lifetime in pressurized gas sealing applications such as O-rings, where weak binding between the filler particle and polymer matrix can lead to internal void structures. With the aim to build a fundamental understanding of precursors to pressurized hydrogen-induced failure in elastomers, we use all-atom molecular dynamics simulations to study the impact of hydrogen oversaturation on filler-polymer interaction strength. We systematically study the interface between a commonly used elastomer, ethylene-propylene-diene monomer (EPDM) and silica by varying gas concentration, crosslink density, and surface chemistry. Our simulations predict that decompression leads to a localization of excess gas near the interface. In conclusion, we demonstrate that this localized gas can weaken interfacial adhesion and quantify the interaction using thermodynamic approaches.

EPDM↗
DOE OSTI2026

Enhancing Value-Added CO Production from CO 2 Hydrogenation by Tailoring the Ru-CeO 2 Interface on MgO

Catalytic CO 2 hydrogenation presents a promising route for converting CO 2 into valuable products, contributing to the mitigation of net CO 2 emissions. Supported Ru catalysts have recently gained considerable attention due to their tunability for 100% CO selectivity via the reverse water-gas shift pathway, effectively suppressing the competing methanation route. However, despite achieving full CO selectivity, the overall CO yield remains limited by low CO 2 conversion, necessitating further improvement. In this work, CeO 2 was introduced to modify a Ru/MgO single-atom catalyst for CO 2 hydrogenation. The resulting Ru-CeO 2 /MgO catalyst, featuring abundant Ru-CeO 2 interfacial sites, exhibited a favorable balance of CO 2 conversion and CO selectivity, delivering the highest CO yield (32.5% at 500 °C), which is 9.0 and 1.8 times higher than that on Ru/MgO (3.6%) and Ru/CeO 2 (18.4%), respectively. Although the CO selectivity was slightly compromised due to enhanced CO binding at Ru-CeO 2 interfacial sites, H 2 was more efficiently activated at these interfaces and readily reacted with CO 2 adsorbed on CeO 2 -MgO surfaces, thereby boosting the CO 2 hydrogenation activity and CO yield. This study underscores the critical role of Ru-metal oxide interface engineering in improving CO yield and advancing the rational design of highly efficient Ru catalysts for CO production from CO 2 hydrogenation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of Surface Terminations of 2D Bi 2 WO 6 on Photocatalytic Hydrogen Evolution from Water Splitting

Two-dimensional (2D)-structured photocatalysts with atomically thin layers not only have the potential to enhance hydrogen generation efficiency but also allow more direct investigations of the effects of surface terminations on photocatalytic activity. In this work, taking 2D Bi 2 WO 6 as a model, we found that the configuration of bilayer Bi 2 O 2 sandwiched by alternating WO 4 layers enabled the thermodynamic driving potential for photocatalytic hydrogen evolution. Without Pt deposition, the H 2 generation efficiency can reach to 56.9 μmol/g/h by 2D Bi 2 WO 6 as compared with no activity of Bi 2 WO 6 nanocrystals under simulated solar light. This configuration is easily functionalized by adsorption of Cl – /Br – to form Bi–Cl/Bi–Br bonds, which leads to the decrease of recombination in photogenerated charge carriers and narrower band gaps. This work highlights an effective way to design photocatalysts with efficient hydrogen evolution by tuning the surface terminations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Structural and thermal properties of Na 2 Mn(SO 4 ) 2 ·4H 2 O and Na 2 Ni(SO 4 ) 2 ·10H 2 O

The title compounds were prepared via a wet chemistry route and their crystal structures were determined from single crystal X-ray diffraction data. Na 2 Mn(SO 4 ) 2 ·4H 2 O crystallizes with a monoclinic symmetry, space group P2 1 /c, with a = 5.5415(2), b = 8.3447(3), c = 11.2281(3) Å, β = 100.172(1)°, V = 511.05(3) Å 3 and Z = 2. Na 2 Ni(SO 4 ) 2 ·10H 2 O also crystallizes with a monoclinic symmetry, space group P2 1 /c, with a = 12.5050(8), b = 6.4812(4), c = 10.0210(6) Å, β = 106.138(2)°, V = 780.17(8) Å3 and Z = 2. Na 2 Mn(SO 4 ) 2 ·4H 2 O is a new member of the blödite family of compounds, whereas Na 2 Ni(SO 4 ) 2 ·10H 2 O is isostructural with Na 2 Mg(SO 4 ) 2 ·10H 2 O. The structure of Na 2 Mn(SO 4 ) 2 ·4H 2 O is built up of [Mn(SO 4 ) 2 (H 2 O) 4 ] 2– building blocks connected through moderate O–H…O hydrogen bonds with the sodium atoms occupying the large tunnels along the a axis and the manganese atom lying on an inversion center, whereas the structure of Na 2 Ni(SO 4 ) 2 ·10H 2 O is built up of [Ni(H 2 O) 6 ] 2+ and [Na 2 (SO 4 ) 2 (H 2 O) 4 ] 2– layers. These layers which are parallel to the (100) plane are interconnected through moderate O–H…O hydrogen bonds. Here, the thermal gravimetric- and the powder X-ray diffraction-analyzes showed that only the nickel phase was almost pure. At a temperature above 300 °C, all the water molecules evaporated and a structural phase transition from P2 1 /c-Na 2 Ni(SO 4 ) 2 ·10H 2 O to C2/c-Na 2 Ni(SO 4 ) 2 was observed. C2/c-Na 2 Ni(SO 4 ) 2 is thermally more stable than Na 2 Fe(SO 4 ) 2 and therefore it would be suitable as the positive electrode for sodium ion batteries if a stable electrolyte at high voltage is developed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Spin-dependent vibronic response of a carbon radical ion in two-dimensional WS 2

Atomic spin centers in 2D materials are a highly anticipated building block for quantum technologies. Here, we demonstrate the creation of an effective spin-1/2 system via the atomically controlled generation of magnetic carbon radical ions (CRIs) in synthetic two-dimensional transition metal dichalcogenides. Hydrogenated carbon impurities located at chalcogen sites introduced by chemical doping are activated with atomic precision by hydrogen depassivation using a scanning probe tip. In its anionic state, the carbon impurity is computed to have a magnetic moment of 1 μ B resulting from an unpaired electron populating a spin-polarized in-gap orbital. We show that the CRI defect states couple to a small number of local vibrational modes. The vibronic coupling strength critically depends on the spin state and differs for monolayer and bilayer WS 2 . The carbon radical ion is a surface-bound atomic defect that can be selectively introduced, features a well-understood vibronic spectrum, and is charge state controlled.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Binding of carboxylate and water to monovalent cations

The interactions of carboxylate anions with water and cations are important for a wide variety of systems, both biological and synthetic. Here, in order to gain insight on properties of the local complexes, we apply density functional theory, to treat the complex electrostatic interactions, and investigate mixtures with varied numbers of carboxylate anions (acetate) and waters binding to monovalent cations, Li + , Na + and K + . The optimal structure with overall lowest free energy contains two acetates and two waters such that the cation is four-fold coordinated, similar to structures found earlier for pure water or pure carboxylate ligands. More generally, the complexes with two acetates have the lowest free energy. In transitioning from the overall optimal state, exchanging an acetate for water has a lower free energy barrier than exchanging water for an acetate. In most cases, the carboxylates are monodentate and in the first solvation shell. As water is added to the system, hydrogen bonding between waters and carboxylate O atoms further stabilizes monodentate structures. These structures, which have strong electrostatic interactions that involve hydrogen bonds of varying strength, are significantly polarized, with ChelpG partial charges that vary substantially as the bonding geometry varies. Overall, these results emphasize the increasing importance of water as a component of binding sites as the number of ligands increases, thus affecting the preferential solvation of specific metal ions and clarifying Hofmeister effects. Finally, structural analysis correlated with free energy analysis supports the idea that binding to more than the preferred number of carboxylates under architectural constraints are a key to ion transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Diastereoselective Hydrogenation of Tetrasubstituted Olefins using a Heterogeneous Pt‐Ni Alloy Catalyst

Abstract Stereoselective hydrogenation of tetrasubstituted olefins is an attractive method to access compounds with two contiguous stereocenters. However, homogeneous catalysts for enantio‐ and diastereoselective hydrogenation exhibit low reactivity toward tetrasubstituted olefins due to steric crowding between the ligand scaffold and the substrate. Monometallic heterogeneous catalysts, on the other hand, provide accessible surface active sites for hindered olefins but exhibit unpredictable and inconsistent stereoinduction. In this work, we develop a Pt−Ni bimetallic alloy catalyst that can diastereoselectively hydrogenate unactivated, sterically‐bulky tetrasubstituted olefins, utilizing the more oxophilic Ni atoms to adsorb a hydroxyl directing group and direct facially‐selective hydrogen addition to the olefin via the Pt atoms. Structure‐activity studies on several Pt−Ni compositions underscore the importance of exposing a uniform PtNi alloy surface to achieve high diastereoselectivity and minimize side reactions. The optimized Pt−Ni/SiO 2 catalyst exhibits good functional group tolerance and broad scope for tetrasubstituted olefins in a cyclopentene scaffold, generating cyclopentanol products with three contiguous stereocenters. The synthetic utility of the method is demonstrated in a four‐step synthesis of (1R,2S)‐(+)‐cis‐methyldihydrojasmonate with high yield and enantiopurity.

Chemistry↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗