Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Temperature Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

High-Performance MnBi Alloy Prepared Using Profiled Heat Treatment

The profiled heat treatment (PHT) method has been used to synthesize MnBi alloys with high-purity low-temperature phase (LTP). In the PHT method, the arc-melted MnBi alloy was remelted then slowly cooled by a pseudo-equilibrium solidification process to promote the formation of LTP phase. The PHT-treated MnBi alloys had an LTP phase up to 94 wt.% and a magnetization of 73 emu/g under a field of 9 T. Scanning electron microscopy showed that there exist some micrometer-sized Mn-rich inclusions in the LTP matrix of the PHT MnBi alloy. The PHT MnBi alloys were crushed into powders with an average size of ~3 μm by low-energy ball milling. These MnBi powders were aligned in an 18 kOe field and warm compacted into a bulk magnet at 300 °C for 30 min. The magnet had a density of 8.2 g/cm3 and magnetic properties of Ms = 6.7 kG, Mr = 5.3 kGs, i Hc = 5 kOe, and (BH)max = 6.1 MGOe

MnBi↗

Modular high temperature gas reactor core modeling with RELAP5-3D/PHISICS – Optimization schemes for load following

The objective of this study is to develop a 3D/NK model to study the load following operation of a Modular High-Temperature Gas-Cooled Reactor (MHTGR). The selected design is the 350 MW prismatic, graphite moderated, helium cooled thermal reactor based on the MHTGR-350 transient benchmark led by the High-Temperature Gas-Cooled Reactor (HTGR) Methods Core Simulation Group at Idaho National Laboratory (INL) in the framework of the Organization for Economic Cooperation and Development Nuclear Energy Agency (OECD/NEA). This kind of reactor usually reacts very slowly to the perturbation of the core parameters due to the large amount of graphite in the core. This kind of behavior promotes the reactor stability but on the other hand limits the reactor load-following operability. Recently advances in gas reactor designs have made load-following in gas reactors a feasible and achievable goal. Modern nuclear reactors (such as the MHTGR-350) are designed to withstand the structural stresses associated with load-following. Operating the reactor in load-following mode will inevitably reduce the load factor. Although a higher load factor means more revenue and the best usage of the fuel, following the variable energy demand will increase the maximum achievable fraction of generated nuclear power, being no more limited to the base load power generation. In general, if low impact on material aging and the safe operability are demonstrated the plant economics will be minimally affected. In order to ensure that the system can be safely operated in a load-following mode an extensively study has been carried out. Some tests with linear coolant mass flow rate change demonstrated that the reactor behavior is suitable for operation in load following mode. This assumption has been confirmed by a 4 days load following transient test in which the reactor supplied the requested power with a negligible error.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enhanced ferromagnetic properties and high temperature dielectric anomalies in Bi{sub 0.9}Ca{sub 0.05}Sm{sub 0.05}FeO{sub 3} prepared by hydrothermal method

Graphical abstract: Temperature variation of dielectric constant of Bi{sub 0.9}Ca{sub 0.05}Sm{sub 0.05}FeO{sub 3} at various frequencies as a function of temperature indicating anomalies at 420 and 540 K. - Highlights: • Substitution of Sm ions for Bi enhances the saturation magnetization of BiFeO{sub 3}. • XPS studies indicate the creation of oxygen vacancies upon Ca substitution. • Dielectric measurements show dielectric anomalies at high temperatures. • Raman spectra at high temperatures confirm the dielectric anomaly temperatures. - Abstract: Enhanced ferromagnetic properties and high temperature dielectric anomalies in the temperature range of 300–873 K in Bi{sub 0.9}Ca{sub 0.05}Sm{sub 0.05}FeO{sub 3} (BCSFO) prepared by hydrothermal method are reported. BiFeO{sub 3} is seen to crystallize in rhombohedrally distorted perovskite structure without any impurity phase. Substitution of small amount of Ca and Sm (Bi{sub 0.9}Ca{sub 0.05}Sm{sub 0.05}FeO{sub 3}) leads to increase in the lattice constant values and formation of small amount of secondary phase. Magnetization curve of pure BFO indicates very weak ferromagnetism combined with antiferromagnetic nature of the samples. Whereas, BCSFO sample shows very clear and enhanced ferromagnetic nature. Saturation magnetization and Neel’s temperature values are found to be 4.36 emu/g and 664 K, respectively. X-ray photoelectron spectroscopy indicates the creation of oxygen vacancies upon Ca substitution in Bi site. Dielectric anomalies at 420 and 540 K were observed for Bi{sub 0.9}Ca{sub 0.05}Sm{sub 0.05}FeO{sub 3} from the temperature variation of dielectric constant and specific heat capacity measurements. Observation of dielectric anomalies in pure BiFeO{sub 3} sample reveals that the origin of dielectric peaks is purely from the primary phase. Raman spectroscopy study indicates a clear shift and broadening of A modes (between 100 and 200 cm{sup −1}) at the dielectric anomaly temperatures supporting the observed dielectric anomalies.

36 MATERIALS SCIENCE↗

Second generation superconducting filaments and cable

A high-temperature superconducting filament and cable, and a method for manufacturing same. The substrate used to grow the superconducting layer is removed, and the exfoliated superconducting layer is coated with a protective layer, and then sliced into narrow strips. The strips are thereafter encapsulated with a conductive metal to provide a high-temperature superconducting filament. The filaments may be bundled together to provide a high-temperature superconducting cable.

Solovyov, Vyacheslav↗

High temperature oxygen treated carbon aerogels

Disclosed here is a method for increasing the hydrophilicity of a carbon aerogel, comprising heating the carbon aerogels under air or a gas having a higher concentration of oxygen than air at a temperature of about 200.degree.-500.degree. C. to obtain an activated carbon aerogel. Also disclosed include an activated carbon aerogel obtained by the method, an electrode comprising the activated carbon aerogel, and a supercapacitor or capacitive deionization device comprising the electrode.

Stadermann, Michael↗

Low temperature electrolytes for solid oxide cells having high ionic conductivity

Methods for forming a metal oxide electrolyte improve ionic conductivity. Some of those methods involve applying a first metal compound to a substrate, converting that metal compound to a metal oxide, applying a different metal compound to the metal oxide, and converting the different metal compound to form a second metal oxide. Electrolytes so formed can be used in solid oxide fuel cells, electrolyzers, and sensors, among other applications.

30 DIRECT ENERGY CONVERSION↗

Low temperature electrolytes for solid oxide cells having high ionic conductivity

Methods for forming a metal oxide electrolyte improve ionic conductivity. Some of those methods involve applying a first metal compound to a substrate, converting that metal compound to a metal oxide, applying a different metal compound to the metal oxide, and converting the different metal compound to form a second metal oxide. That substrate may be in nanobar form that conforms to an orientation imparted by a magnetic field or an electric field applied before or during the converting. Electrolytes so formed can be used in solid oxide fuel cells, electrolyzers, and sensors, among other applications.

Budaragin, Leonid V.↗

The Radioactivity Characteristics of the NPP Charcoal Sample Contaminated by Carbon-14 - 13531

The radioactivity of {sup 14}C-contaminated charcoal sample was analyzed by using a high temperature oxidation and liquid scintillation counting method. The radioactivity of the sample was monotonically increased according to the increase of the combustion time at each temperature where the experimental uncertainty was calculated in the 95 % confidence level. It showed that the {sup 14}C radioactivity was not completely extracted from the sample by simply increasing the combustion time unless the combustion temperature was high enough. The higher the combustion temperature was, the higher the recovery during the first 30 minutes was. The first 30 minute recoveries were 100 % at a temperature equal to or greater than 450 deg. C. The ratios of the recovery during the first 30 minutes to the total recovery during whole duration were more than 90 % at each experiment temperature. It was understood that the temperature was a critical factor for the complete removal of the {sup 14}C from the waste sample. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Expanding Parameter Space to Enable Low-Temperature Synthesis of Crystalline Indium Phosphide Quantum Dots

Established methods to synthesize indium phosphide quantum dots (QDs) require high temperatures (>180 °C) to make high-quality material for optoelectronic applications. Nonpolar solvent environments are overwhelmingly used in InP QD synthesis to reach the necessary high temperatures and for compatibility with the reactive precursors. In this study, we explored InP QD synthesis in polar aprotic solvent environments to dramatically decrease the temperature required for InP crystallization by imparting ionicity to the precursors and stabilizing charged reaction intermediates. A custom air-free 96- well plate setup was employed to identify key factors impacting low-temperature QD formation, including an increased percentage of polar solvent, carboxylic acid choice, and inclusion of polar additives. Guided by these insights, we developed a synthesis of crystalline, green-emitting InP QDs at 60 °C in a toluene-dimethylformamide mixture. Here's, the QDs withstood established Zn 2+ and HF surface treatments, which increased the photoluminescence quantum yield to 25%. Additionally, we demonstrated the rapid synthesis of quasi-wurtzite InP QDs at room temperature in a polar solvent environment using an acid-free indium myristate precursor.

absorption↗

The COMET method in 3-D hexagonal geometry

The hybrid stochastic-deterministic coarse mesh radiation transport (COMET) method developed at Georgia Tech now solves reactor core problems in 3-D hexagonal geometry. In this paper, the method is used to solve three preliminary test problems designed to challenge the method with steep flux gradients, high leakage, and strong asymmetry and heterogeneity in the core. The test problems are composed of blocks taken from a high temperature test reactor benchmark problem. As the method is still in development, these problems and their results are strictly preliminary. Results are compared to whole core Monte Carlo reference solutions in order to verify the method. Relative errors are on the order of 50 pcm in core eigenvalue, and mean relative error in pin fission density calculations is less than 1% in these difficult test cores. The method requires the one-time pre-computation of a response expansion coefficient library, which may be compiled in a comparable amount of time to a single whole core Monte Carlo calculation. After the library has been computed, COMET may solve any number of core configurations on the order of an hour, representing a significant gain in efficiency over other methods for whole core transport calculations. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Polar nanoregions and dielectric properties in high-strain lead-free 0.93(Bi{sub 1/2}Na{sub 1/2})TiO{sub 3}-0.07BaTiO{sub 3} piezoelectric single crystals

A structural coexistence of rhombohedral (R) and tetragonal (T) phases has been revealed in the (001){sub c}-cut lead-free 0.93(Bi{sub 1/2}Na{sub 1/2})TiO{sub 3}–0.07BaTiO{sub 3} (BNB7T) piezoelectric crystals, which grown by the self-flux method, in the lower temperatures by high-resolution synchrotron X-ray diffraction, reciprocal space mapping, and transmission electron microscopy. The dielectric permittivity exhibits a thermal hysteresis in the region of 120–260 °C, implying a first-order-like phase transition from R+T to T. The real part (ε′) of dielectric permittivity begins to deviates from the Curie-Weiss equation, ε′ = C/(T − T{sub o}), from the Burns temperature T{sub B} = 460 °C, below which the polar nanoregions (or nanoclusters) develop and attenuate dielectric responses. The polar nanoregions of 5–10 nm were revealed by high-resolution transmission electron microscope. The normal piezoelectric coefficient d{sub 33} exhibits a rapid increase at E = 15–20 kV/cm and reaches a maximum of d{sub 33} ∼450 pC/N. The high piezoelectric response and E-field induced strain in BNB7T single crystals can be attributed to structural phase transitions under an E-field application.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Highly Active and Stable Single Atom Rh 1 /CeO 2 Catalyst for CO Oxidation during Redox Cycling

We report a single atom Rh 1 /CeO 2 catalyst prepared by the high temperature (800 °C) atom trapping (AT) method which is stable under both oxidative and reductive conditions. Infrared spectroscopic and electron microscopy characterization revealed the presence of exclusively ionic Rh species. These ionic Rh species are stable even under reducing conditions (CO at 300 °C) due to the strong interaction between Rh and CeO 2 achieved by the AT method, leading to high and reproducible CO oxidation activity regardless of whether the catalyst is reduced or oxidized. In contrast, ionic Rh species in catalysts synthesized by a conventional impregnation approach (e. g., calcined at 350 °C) can be readily reduced to form Rh nanoclusters/nanoparticles, which are easily oxidized under oxidative conditions, leading to loss of catalytic performance. The single atom Rh 1 /CeO 2 catalysts synthesized by the AT method do not exhibit changes during redox cycling hence are promising catalysts for emission control where redox cycling is encountered, and severe oxidation (fuel cut) leads to loss of performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of ASME Division 5 Code proposal on temperature limits for simplified design methods

This report establishes proposed upper temperature limits for the ASME BP&V Code Section III, Division 5, Nonmandatory Appendix HBB-T design by elastic analysis provisions for bounding ratcheting strain and creep-fatigue damage in Class A high temperature nuclear reactor components. Limitations on the use of these design options are required because the design by elastic analysis methods rely on bounding theories that assume a non-unified, decoupled model of creep-plasticity. However, at high temperatures creep and plastic deformation become coupled and bounding theorems relying a decoupled material response may fail. The report describes a method for selecting appropriate upper temperature limits, demonstrates directly through a comparison to full inelastic simulations that the existing Code provisions can be nonconservative at high temperatures, and develops the requisite Code language required to implement the temperature limits in Section III, Division 5.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Novel Geochemistry Determined from High Pressure, High Temperature Simulation Experiments of Hydraulic Fracture Test Site 2

A standard method in unconventional oil and gas production is the process of hydraulic fracturing followed by a shut-in period, during which the fracture fluid remains pressurized in the reservoir for up to three weeks before production begins. Despite this widely used process, very little is known about what occurs in the reservoir during this shut-in process. In order to properly delineate potential reservoir reactions that may occur during shut-in that would lead to corrosion and scaling events, experiments were conducted in high pressure, high temperature reactors to simulate conditions of the Wolfcamp Formation in the Delaware Basin. Experimental design allowed the assessment of the effect of proppant, microbiology, and time on the mineralogy and fluid chemistry in the reservoir. Results suggest the biggest impact on fluid chemistry and shale mineralogy during shut-in is time. Analyses demonstrate dissolution of the shale material, with maximum dissolved ions occurring after 7 days of the shut-in period. After 21 days, results suggest precipitation occurs. The Delaware Basin is demonstrated to be high in sulfate content, which further increases in the fluid due to dissolution reactions during shut-in. The pressure vessel experiments suggest there was no significant contribution to reactions from microbiology during the shut-in period. Furthermore, early production samples demonstrate a significant selection of the microorganism Caminicella, a genus of which has previously been correlated to corrosion and sulfide production. Results suggest shut-in conditions may provide high sulfate concentrations that could later be utilized by a shifted microbial community to drive potential well infrastructure failure. This is the first study to incorporate microbiology, mineralogy, and fluid chemistry to investigate the fundamental geochemical reactions that occur during shut-in and early phase production of the Delaware Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/2-21URTC/D021S032R001/2477425/urtec-2021-5219-ms.pdf/1 by Carol Worster on 28 February 2022 Basin. Results from this study can complement observations from the Hydraulic Fracture Test Site 2 observations

58 GEOSCIENCES↗

Advanced low-cost intermetallic coatings for molten salt pump impeller. Final report

1.0 INTRODUCTION The use of solar energy to produce steam for the generation of electricity is an established technology, with multiple designs for concentrating solar power (CSP) steam generators available commercially and a number of such units currently operating. As part of the effort to improve the overall efficiency of this technology, designers have developed thermal energy storage (TES) mechanisms that employ molten salt to capture a portion of the solar energy available during the day-time hours and make that energy available for steam generation during periods when the sun’s energy is not available. In current TES systems, nitrate salts are used extensively as the medium of energy exchange. However, due to the chemical instability of these salts at temperatures above 600ºC, they are not being considered for use in the next more efficient generation of CSP plants, in which the energy exchange fluids will be required to operate in the range 600ºC to 800ºC. At these higher temperatures, molten chloride salts, such as KCl-MgCl2, are viewed as promising alternatives to the nitrate salts, but, of course, these chloride-based salts are highly corrosive to the engineering alloys commonly used in the construction of pressure vessels, heat exchangers, pumps and piping at high temperatures. Hence, a solution to the problem of material degradation is essential if the next generation of CSP plants is to be commercially viable (Ref 1). In order to effectively address the problem of molten chloride salt corrosion at high temperatures (≥ 750ºC) and thereby to reduce the cost of molten salt tanks and related apparatus, various options have been considered, with one of the most promising being an innovative coatings system developed and applied onto low alloy ferritic or austenitic stainless material. Development of such a coating system would reduce the capital costs of thermal energy storage (TES) and increase the overall efficiency of the concentrating solar power (CSP) system. Although high strength nickel base alloys are well suited for many high temperature applications, they have significant limitations when exposed to molten chloride salt conditions and they are very expensive. Monolithic materials such as the austenitic stainless steels (e.g., SS310 and SS347) and the more common nickel base alloys (e.g., IN625 and IN800H) have exhibited high corrosion rates in molten chloride salt environments (Ref1). Molten salt corrosion of IN625 in salts containing chlorides showed a catastrophic corrosion rate of 1.111”/year at 800ºC (Ref1). Hence, an innovative coatings solution to mitigate molten chloride salt corrosion is needed. Of the many coating techniques available in the market, no one technique appears to be capable of producing effective protection from molten salt corrosion at a relatively low cost. There are thermal spray coating techniques, in particular the twin wire-arc technology, that are attractive when considering the coating of large molten salt tanks because the coatings application rate is high, the overall application cost is low and repairs to the coating can readily be made either in the shop or in the field. However, the twin wire arc coating materials currently available in the market have certain inherent limitations, including porosity and mechanical bonding to the substrate, which limit their effectiveness in providing protection against molten chloride salt corrosion at high temperatures. What is required is an approach that combines the economy and versatility of thermal spray wire-arc technology with the superior resistance of advanced alloys to effectively combat molten chloride salt corrosion at elevated temperatures. Applied Thermal Coatings, Inc. (ATC) has investigated an innovative coatings technology to produce dual layer cermet/ceramic coatings that will be dense and impervious to any corrosive molten salts/fluids, thereby resisting the effects of molten salt corrosion. Development of coatings using this technology will make it possible to fabricate the molten salt systems using a relatively low-cost base material, which will reduce the overall cost of the power generating system and enhance the commercial viability of solar power. 2.0 PROJECT OVERVIEW Of the coating technologies available for the production of a cost-effective method of protection from the effects of high-temperature chloride attack, there are two that offer specific advantages for the CSP/TES application, particularly when used in a way that effectively complements the strengths of each coating method. The first of these is electroless nickel plating, through which a nickel-rich layer is produced on the surface of a component through chemical reduction. The second coating technology is aluminizing, in which aluminum is diffused into the surface of a component and, depending on the composition of the substrate, aluminides are formed. The objective of this project has been to demonstrate the feasibility of a low- cost coating for the protection of pump impellers used for the inductive transport of molten salts. Initial interest focused on an inter-metallic nickel aluminide coating and subsequently, for economic reasons, consideration also was given to a coating composed of iron aluminides. Applying such coatings to low alloy or austenitic stainless-steel substrates will provide the superior resistance to molten chloride salt corrosion and blade tip erosion that normally can be achieved only through the use of more highly alloyed – and, therefore, more expensive - nickel-base materials and it will do so at a substantially lower cost. The coating systems evaluated were designed to take advantage either of the combined strengths of the electroless nickel plating process and the aluminizing process to produce a nickel-aluminide intermetallic coating or to rely solely on the aluminizing process to produce, in conjunction with iron from the substrate, a protective layer consisting of iron aluminides. With respect to the nickel aluminide protection, this has been achieved by first depositing a layer of nickel-rich alloy onto an austenitic stainless substrate using the electroless nickel plating process and then aluminizing the nickel- coated surface to produce the nickel aluminide coating. With respect to the iron aluminide protection, this has been achieved by aluminizing bare austenitic stainless steel. Testing has supported the conclusion that the developed coatings will resist attack by molten chloride salts at high temperatures (550°C to 750°C) and have sufficient hardness to resist blade tip erosion.The steps taken to develop either a low-cost intermetallic nickel aluminide coating using electroless nickel plating and aluminizing or a low-cost iron aluminide coating using aluminizing only, and to demonstrate the quality of the coatings and their effectiveness against molten chloride salt corrosion and erosion at high temperatures (≤ 750ºC) have been as follows: 1. Design of the optimum electroless nickel plating and aluminizing mixtures using advanced thermodynamic analysis; 2. Development of processing parameters for the electroless nickel plating and aluminizing processes, to be used either together or separately; 3. Production of specimens coated using the designated electroless nickel plating process; 4. Production of samples with intermetallic nickel aluminide coating or iron aluminide coating; 5. Investigation of the performance of the intermetallic nickel aluminide coating and the iron aluminide coating when subjected to molten chloride salts corrosion at high temperatures (≥ 750ºC); and, 6. Metallurgical characterization of the microstructure of the coatings, both prior to and after exposure to molten salt environments at elevated temperatures.

14 SOLAR ENERGY↗

Water‐Assisted Liftoff of Polycrystalline CdS/CdTe Thin Films Using Heterogeneous Interfacial Engineering

Abstract Recent advances in device design and process optimizations have enabled the production of CdTe devices on flexible substrates, but the necessary high‐temperature processing (>450 °C) to recrystallize grains limits the use of alternative lightweight substrates. Here, a new synthesis method is reported to create a freestanding CdS/CdTe film by combining high‐temperature depositions (CdS/CdTe on Si/SiO 2 ) and a simple lift‐off process in a water environment at room temperature. Analysis of the results indicate that the delamination is facilitated by the innate lattice mismatch as well as the presence of an unexpected Te‐rich layer (≈20 nm), which accumulates on the SiO 2 surface. High‐resolution electron microscopy and spectroscopy measurements confirm that the CdS/CdTe film is physically liberated from the substrate without leaving any residue, while also preserving their initial structural and compositional properties.

Magginetti, David J.↗

Development of a method for measuring the density of liquid sulfur at high pressures using the falling-sphere technique

We describe a new method for the in situ measurement of the density of a liquid at high pressure and high temperature using the falling-sphere technique. Combining synchrotron radiation X-ray radiography with a large-volume press, the newly developed falling-sphere method enables the determination of the density of a liquid at high pressure and high temperature based on Stokes' flow law. We applied this method to liquid sulfur and successfully obtained the density at pressures up to 9 GPa. Our method could be used for the determination of the densities of other liquid materials at higher static pressures than are currently possible.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗