Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hover Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

593 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

A direct application of the non-linear inverse transformation flight control system design on a STOVL aircraft

The nonlinear inverse transformation flight control system design method is applied to the Lockheed Ft. Worth Company's E-7D short takeoff and vertical land (STOVL) supersonic fighter/attack aircraft design with a modified General Electric F110 engine which has augmented propulsive lift capability. The system is fully augmented to provide flight path control and velocity control, and rate command attitude hold for angular axes during the transition and hover operations. In cruise mode, the flight control system is configured to provide direct thrust command, rate command attitude hold for pitch and roll axes, and sideslip command with turn coordination. A control selector based on the nonlinear inverse transformation method is designed specifically to be compatible with the propulsion system's physical configuration which has a two dimensional convergent-divergent aft nozzle, a vectorable ventral nozzle, and a thrust augmented ejector. The nonlinear inverse transformation is used to determine the propulsive forces and nozzle deflections, which in combination with the aerodynamic forces and moments (including propulsive induced contributions), and gravitational force, are required to achieve the longitudinal and vertical acceleration commands. The longitudinal control axes are fully decoupled within the propulsion system's performance envelope. A piloted motion-base flight simulation was conducted on the Vertical Motion Simulator (VMS) at NASA Ames Research Center to examine the handling qualities of this design. Based on results of the simulation, refinements to the control system have been made and will also be covered in the report.

Chung, W. W.↗
NASA NTRSDate not supplied

Comparison of Prediction Modeling Methodologies for Aeroacoustic Characterization of Hovering sUAS Rotors

This work compared artificial neural network and multivariate orthogonal function modeling methodologies for the prediction and characterization of isolated hovering sUAS rotor aerodynamics and aeroacoustics. Design of Experiments was used to create input feature spaces over 9 input features: the number of rotor blades, rotor size, rotor speed, the amount of blade twist, blade taper ratio, tip chord length, collective pitch, airfoil camber, and airfoil thickness. CAMRAD~II and AARON were executed at the points defined by the input feature space to predict aerodynamic and aeroacoustic quantities. These predicted aerodynamic and aeroacoustic data were then used to generate artificial neural networks and polynomial response surface models. The two prediction model methodologies were evaluated over test data previously unseen by the models, which showed good prediction capabilities for both model types, with slightly lower prediction error for the artificial neural networks. A characterization study was performed, which showed that input features correspondent to the spanwise sectional blade lift and drag were the most significant factors to the aerodynamic thrust and power, respectively. It was also shown that the aeroacoustic quantities were highly dependent on variations in rotor speed and size, which affect the Doppler factor for tonal noise and the spanwise Reynolds number for broadband noise.

Christopher S Thurman↗
NASA NTRS2003

Mechanization and Control Concepts for Biologically Inspired Micro Aerial Vehicles

It is possible that MAV designs of the future will exploit flapping flight in order to perform missions that require extreme agility, such as rapid flight beneath a forest canopy or within the confines of a building. Many of nature's most agile flyers generate flapping motions through resonant excitation of an aeroelastically tailored structure: muscle tissue is used to excite a vibratory mode of their flexible wing structure that creates propulsion and lift. A number of MAV concepts have been proposed that would operate in a similar fashion. This paper describes an ongoing research activity in which mechanization and control concepts with application to resonant flapping MAVs are being explored. Structural approaches, mechanical design, sensing and wingbeat control concepts inspired by hummingbirds, bats and insects are examined. Experimental results from a testbed capable of generating vibratory wingbeat patterns that approximately match those exhibited by hummingbirds in hover, cruise, and reverse flight are presented.

Raney, David L.↗
NASA NTRSDate not supplied

Integral Velocity Sampling for Unsteady Rotor Models on Cartesian Meshes

An unsteady body-force rotor model utilizing integral velocity sampling is developed for Cartesian meshes with a focus on accurate performance predictions. In this approach, the rotors are modeled as body-force source terms, and integral sampling is used to define the local freestream velocity vector. The method is verified in two dimensions for airfoils, providing accurate angle of attack and freestream Mach number estimates even on relatively coarse meshes, and demonstrating excellent mesh convergence across a variety of source region thicknesses. Extensions of the model to three dimensions for both fixed and rotating wings are considered, with numerical experiments demonstrating the need for a spanwise-continuous representation of the induced velocity or angle of attack. The model provides reasonable spanwise lift distributions without any explicit tip-loss model. Comparisons to high-fidelity simulations and experimental data show excellent agreement for predictions of an isolated DJI Phantom 3 propeller in hover. Finally, simulations of the full aircraft in edgewise forward flight also compare well with wind tunnel data across a variety of pitch angles and propeller speeds.

ARMD↗
NASA NTRS1986

Directional handling qualities requirements for nap-of-the-earth tasks

A piloted similator experiment designed to investigate directional axis handling qualities requirements for low-speed and hover tasks conducted by a scout/attack helicopter is described. Included were the directional characteristics of various candidate light helicopter family (LHX) configurations. The test also focused on conventional single main/tail rotor configurations where the first-order effects that contribute to the loss of tail rotor control experienced by the OH-58 series aircraft were modeled. Two types of yaw stability and control augmentation systems were implemented: washed-out yaw rate feedback and shaped control input, and a yaw rate command, heading-hold system. The results of the experiment indicate that rotorcraft configurations with high directional gust sensitivity require more yaw damping to maintain satisfactory handling qualities during nap-of-the-earth (NOE) flying tasks. It was also determined that both yaw damping and control response are critical handling qualities parameters in performing the air-to-air target acquisition and tracking task. The lack of substantial yaw damping and larger values of gust sensitivity increased the possibility of loss of directional control at low airspeeds for the tail rotor configurations.

Bivens, C. C.↗
NASA NTRS2002

Rotor/Wing Interactions in Hover

Hover predictions of tiltrotor aircraft are hampered by the lack of accurate and computationally efficient models for rotor/wing interactional aerodynamics. This paper summarizes the development of an approximate, potential flow solution for the rotor-on-rotor and wing-on-rotor interactions. This analysis is based on actuator disk and vortex theory and the method of images. The analysis is applicable for out-of-ground-effect predictions. The analysis is particularly suited for aircraft preliminary design studies. Flow field predictions from this simple analytical model are validated against experimental data from previous studies. The paper concludes with an analytical assessment of the influence of rotor-on-rotor and wing-on-rotor interactions. This assessment examines the effect of rotor-to-wing offset distance, wing sweep, wing span, and flaperon incidence angle on tiltrotor inflow and performance.

Young, Larry A.↗
NASA NTRS1996

Flight evaluation of advanced controls and displays for transition and landing on the NASA V/STOL systems research aircraft

Flight experiments were conducted on Ames Research Center's V/STOL Systems Research Aircraft (VSRA) to assess the influence of advanced control modes and head-up displays (HUD's) on flying qualities for precision approach and landing operations. Evaluations were made for decelerating approaches to hover followed by a vertical landing and for slow landings for four control/display mode combinations: the basic YAV-8B stability augmentation system; attitude command for pitch, roll, and yaw; flightpath/acceleration command with translational rate command in the hover; and height-rate damping with translational-rate command. Head-up displays used in conjunction with these control modes provided flightpath tracking/pursuit guidance and deceleration commands for the decelerating approach and a mixed horizontal and vertical presentation for precision hover and landing. Flying qualities were established and control usage and bandwidth were documented for candidate control modes and displays for the approach and vertical landing. Minimally satisfactory bandwidths were determined for the translational-rate command system. Test pilot and engineer teams from the Naval Air Warfare Center, the Boeing Military Airplane Group, Lockheed Martin, McDonnell Douglas Aerospace, Northrop Grumman, Rolls-Royce, and the British Defense Research Agency participated in the program along with NASA research pilots from the Ames and Lewis Research Centers. The results, in conjunction with related ground-based simulation data, indicate that the flightpath/longitudinal acceleration command response type in conjunction with pursuit tracking and deceleration guidance on the HUD would be essential for operation to instrument minimums significantly lower than the minimums for the AV-8B. It would also be a superior mode for performing slow landings where precise control to an austere landing area such as a narrow road is demanded. The translational-rate command system would reduce pilot workload for demanding vertical landing tasks aboard ship and in confined land-based sites.

Franklin, James A.↗
NASA NTRS1984

A 0.15-scale study of configuration effects on the aerodynamic interaction between main rotor and fuselage

Hover and forward flight tests were conducted to investigate the mutual aerodynamic interaction between the main motor and fuselage of a conventional helicopter configuration. A 0.15-scale Model 222 two-bladed teetering rotor was combined with a 0.15-scale model of the NASA Ames 40x80-foot wind tunnel 1500 horsepower test stand fairing. Configuration effects were studied by modifying the fairing to simulate a typical helicopter forebody. Separation distance between rotor and body were also investigated. Rotor and fuselage force and moment as well as pressure data are presented in graphical and tabular format. Data was taken over a range of thrust coefficients from 0.002 to 0.007. In forward flight speed ratio was varied from 0.1 to 0.3 with shaft angle varying from +4 to -12 deg. The data show that the rotors effect on the fuselage may be considerably more important to total aircraft performance than the effect of the fuselage on the rotor.

Trept, Ted↗
NASA NTRS2001

Integral Twist Actuation of Helicopter Rotor Blades for Vibration Reduction

Active integral twist control for vibration reduction of helicopter rotors during forward flight is investigated. The twist deformation is obtained using embedded anisotropic piezocomposite actuators. An analytical framework is developed to examine integrally-twisted blades and their aeroelastic response during different flight conditions: frequency domain analysis for hover, and time domain analysis for forward flight. Both stem from the same three-dimensional electroelastic beam formulation with geometrical-exactness, and axe coupled with a finite-state dynamic inflow aerodynamics model. A prototype Active Twist Rotor blade was designed with this framework using Active Fiber Composites as the actuator. The ATR prototype blade was successfully tested under non-rotating conditions. Hover testing was conducted to evaluate structural integrity and dynamic response. In both conditions, a very good correlation was obtained against the analysis. Finally, a four-bladed ATR system is built and tested to demonstrate its concept in forward flight. This experiment was conducted at NASA Langley T~ansonic Dynamics Tunnel and represents the first-of-a-kind Mach-scaled fully-active-twist rotor system to undergo forward flight test. In parallel, the impact upon the fixed- and rotating-system loads is estimated by the analysis. While discrepancies are found in the amplitude of the loads under actuation, the predicted trend of load variation with respect to its control phase correlates well. It was also shown, both experimentally and numerically, that the ATR blade design has the potential for hub vibratory load reduction of up to 90% using individual blade control actuation. Using the numerical framework, system identification is performed to estimate the harmonic transfer functions. The linear time-periodic system can be represented by a linear time-invariant system under the three modes of blade actuation: collective, longitudinal cyclic, and lateral cyclic. A vibration minimizing controller is designed based on this result, which implements classical disturbance rejection algorithm with some modifications. The controller is simulated numerically, and more than 90% of the 4P hub vibratory load is eliminated. By accomplishing the experimental and analytical steps described in this thesis, the present concept is found to be a viable candidate for future generation low-vibration helicopters. Also, the analytical framework is shown to be very appropriate for exploring active blade designs, aeroelastic behavior prediction, and as simulation tool for closed-loop controllers.

Shin, SangJoon↗
NASA NTRS2018

Results of NASA Technical Challenge to Demonstrate Two-Speed Drive for Vertical Lift Vehicle

Currently, manned vertical lift vehicles are flown in a manner such that the rotors operate over a narrow range of rotating speed regardless if the vehicle's flight condition is one of vertical takeoff and landing, hover, or forward cruise. The propulsion systems are optimized for operation at the same, corresponding narrow range of rotor speed. However, certain missions and markets benefit greatly if the rotor speed can be adjusted over a wide range of speed to match demands of different missions and flight regimes. A vehicle that can operate with a wide range of rotor speeds would address key barriers to enable new markets and missions for vertical lift vehicles. Key barriers addressed by the wide-range of rotor speed include noise reduced via lower rpm rotor, increase of maximum forward flight speed, increased payload and range, reduced fuel burn, and lower operating costs. A new paradigm for the propulsion system is needed to enable these key benefits. One viable approach is to make use of a two-speed ratio drive system such that the engine can continue to operate over a narrow speed range, whereby engine performance is optimal, while adjusting the rotor speed as needed using the two-speed drive system. Motivated by such needs and by results of several system studies, a NASA Revolutionary Vertical Lift Technology Challenge was established to develop and demonstrate required technologies and designs for achieving a 50% reduction in rotor rpm via a two-speed drive system that incurs less than 2% power loss and maintains current power-to-weight ratios. The technical challenge work was completed and the technical objectives were achieved. This report describes the motivations, the research approach and the significant outcomes.

Transmissions↗
NASA NTRS1991

Technology needs for high speed rotorcraft (3)

The spectrum of vertical takeoff and landing (VTOL) type aircraft is examined to determine which aircraft are most likely to achieve high subsonic cruise speeds and have hover qualities similar to a helicopter. Two civil mission profiles are considered: a 600-n.mi. mission for a 15- and a 30-passenger payload. Applying current technology, only the 15- and 30-passenger tiltfold aircraft are capable of attaining the 450-knot design goal. The two tiltfold aircraft at 450 knots and a 30-passenger tiltrotor at 375 knots were further developed for the Task II technology analysis. A program called High-Speed Total Envelope Proprotor (HI-STEP) is recommended to meet several of these issues based on the tiltrotor concept. A program called Tiltfold System (TFS) is recommended based on the tiltrotor concept. A task is identified to resolve the best design speed from productivity and demand considerations based on the technology that emerges from the recommended programs. HI-STEP's goals are to investigate propulsive efficiency, maneuver loads, and aeroelastic stability. Programs currently in progress that may meet the other technology needs include the Integrated High Performance Turbine Engine Technology (IHPTET) (NASA Lewis) and the Advanced Structural Concepts Program funded through NASA Langley.

Detore, Jack↗
NASA NTRS2016

Measurement and Characterization of Helicopter Noise at Different Altitudes

This paper presents an overview of a flight test campaign performed at different test sites whose altitudes ranged from 0 to 7000 feet above mean sea level (AMSL) between September 2014 and February 2015. The purposes of this campaign were to: investigate the effects of altitude variation on noise generation, investigate the effects of gross weight variation on noise generation, establish the statistical variability in acoustic flight testing of helicopters, and characterize the effects of transient maneuvers on radiated noise for a medium-lift utility helicopter. In addition to describing the test campaign, results of the acoustic effects of altitude variation for the AS350 SD1 and EH-60L aircraft are presented. Large changes in acoustic amplitudes were observed in response to changes in ambient conditions when the helicopter was flown at constant indicated airspeed and gross weight at the three test sites. However, acoustic amplitudes were found to scale with ambient pressure when flight conditions were defined in terms of the non-dimensional parameters, such as the weight coefficient and effective hover tip Mach number.

Watts, Michael E.↗
NASA NTRS1994

Controls design with crossfeeds for hovering rotorcraft using quantitative feedback theory

This work is extending the research accomplished on project NCC2-751. A newly implemented helicopter model has been used to simulate 25 flight configurations near hover for the UH-60 RASCAL aircraft. A new engine model has been installed in the FORECAST simulation (alias UMGENHEL) for the better prediction of the yaw and heave responses. By applying the decoupling metric from project NCC 751 it was determined that the aileron to pitch and the elevator to yaw responses do not indicate the need for crossfeeds since both of them have a decoupling metric value over 20 dB (less than 10 percent coupling). In the case of the aileron to heave and the elevator to heave responses, the large size and the overlapping of the templates indicate that a low-order dynamic crossfeed cannot be found. The low-order dynamic crossfeed selection is proceeding, however, for the remaining eight crossfeeds. Note that most of them have successfully decoupled the system by 20 dB or more, except for the rudder to heave crossfeed (18.2 dB). It is probable that the engine model needs more accuracy to further improve the heave to yaw crossfeed decoupling metric value. To see how the new low-order dynamic crossfeeds perform, a simulation was accomplished using MATLAB SIMULINK.

Biezad, Daniel J.↗
NASA NTRSDate not supplied

Acoustic Flight Test of the Joby Aviation Advanced Air Mobility Prototype Vehicle

An extensive acoustic flight test was performed on the Joby Aviation pre-production all-electric vertical takeoff and landing prototype. With the design intent of carrying a pilot and four passengers a maximum range of 150 miles, this vehicle utilizes distributed propulsion and vectored thrust via six tilting propellers. As part of the Advanced Air Mobility (AAM) National Campaign, this is the first full-scale AAM aircraft tested by NASA over representative conditions for all phases of a typical mission profile. A 58- channel distributed microphone array was used to acquire acoustic measurements on more than 100 test points (31 unique conditions). The measurements were postprocessed with synchronously sampled vehicle position and state data to form ground noise contours of departures and approaches at various flight path angles and accelerations. Comparing ground areas of 75 dBA isolines, approaches consistently exhibit higher noise levels rela- tive to departures. Directivity maps were generated for constant airspeed level flyovers. Examples comparing the differences in a semi-thrust borne and full wing-borne mode are given, with full wing-borne mode representing the quietest phase of the flight envelope tested. Measurements for hover in and out of ground effect are given and found to have 2 to 5 dB variation over a single run, and more significant variation between back-to-back runs. Finally, initial analysis of acoustic symmetry about the longitudinal vehicle axis and repeatability over several test days are presented.

Acoustics↗
NASA NTRS2018

The Zwicky Transient Facility: System Overview, Performance, and First Results

The Zwicky Transient Facility (ZTF) is a new optical time-domain survey that uses the Palomar 48 inch Schmidt telescope. A custom-built wide-field camera provides a 47 deg ^(2) field of view and 8 s readout time, yielding more than an order of magnitude improvement in survey speed relative to its predecessor survey, the Palomar Transient Factory. We describe the design and implementation of the camera and observing system. The ZTF data system at the Infrared Processing and Analysis Center provides near-real-time reduction to identify moving and varying objects. We outline the analysis pipelines, data products, and associated archive. Finally, we present on-sky performance analysis and first scientific results from commissioning and the early survey. ZTF’s public alert stream will serve as a useful precursor for that of the Large Synoptic Survey Telescope.

Eric C. Bellm↗
NASA NTRS2016

Computational Study of Flow Interactions in Coaxial Rotors

Although the first idea of coaxial rotors appeared more than 150 years ago, most helicopters have used single main-rotor/tail-rotor combination. Since reactive moments of coaxial rotors are canceled by contra-rotation, no tail rotor is required to counter the torque generated by the main rotor. Unlike the single main rotor design that distributes power to both main and tail rotors, all of the power for coaxial rotors is used for vertical thrust. Thus, no power is wasted for anti-torque or directional control. The saved power helps coaxial rotors reach a higher hover ceiling than single rotor helicopters. Another advantage of coaxial rotors is that the overall rotor diameter can be reduced for a given vehicle gross weight because each rotor provides a maximum contribution to vertical thrust to overcome vehicle weight. However, increased mechanical complexity of the hub has been one of the challenges for manufacturing coaxial rotorcraft. Only the Kamov Design Bureau of Russia had been notably successful in production of coaxial helicopters until Sikorsky built X2, an experimental compound helicopter. Recent developments in unmanned aircraft systems and high-speed rotorcraft have renewed interest in the coaxial configuration. Multi-rotors are frequently used for small electric unmanned rotorcraft partly due to mechanical simplicity. The use of multiple motors provides redundancy as well as cost-efficiency. The multi-rotor concept has rarely been used until recently because of its inherent stability and control problems. However, advances in inexpensive electronic flight control systems have opened the floodgates for small drones using multirotors. Coaxial rotors have started to appear in some multi-rotor configurations. Small coaxial rotors have often been designed using a hundred year old approach that is "sketch, build, fly, and iterate." In that approach, there is no systematic way to explore trade-offs or determine logical next steps. It is neither possible to account for multiple real-world constraints up front in design nor possible to know what performance is possible with a given design. Since unmanned vehicles are sized and optimized for the particular mission, a modern low-fidelity conceptual design and sizing tool that has been used for the design of large helicopters can be used for design of small coaxial rotorcraft. However, unlike most helicopters with single main rotor, the interactions between the upper and lower rotors emerge as an important factor to consider in design because an increase in performance of a multi-rotor system is not proportional to the number of rotors. Interference losses and differences in thrusts between the upper and lower rotors were investigated by theoretical methods as well as a computational fluid dynamics (CFD) method using the Reynolds-Averaged Navier-Stokes (RANS) equations. In this work, hybrid turbulence models are used to investigate the physics of interactions between coaxial rotors and a fuselage that are not well understood. Present study covers not only small-scale drones but also large-scale coaxial rotors for heavy-lifting missions. Considering the recently proposed FAA drone rules that require the flight only in visual line-of-sight, a large multirotor might be used as an airborne carrier for launch and recovery of unmanned aircraft systems with a human operator onboard. For applications to civil operations, their aerodynamic performance and noise levels need to be assessed. Noise is one of the largest limiting factors to rotorcraft operations in urban area. Since the high-frequency noise of multi-rotors may increase the annoyance, noise may turn out to be a key issue that must be addressed for market acceptability. One of the objectives of the present work is to study the effects of inter-rotor spacing and collectives on the performance, efficiency, and acoustics of coaxial rotor systems.

Study↗
NASA NTRS1959

Maximum Mean Lift Coefficient Characteristics at Low Tip Mach Numbers of a Hovering Helicopter Rotor Having an NACA 64(1)A012 Airfoil Section

An investigation has been conducted on the Langley helicopter test tower to determine experimentally the maximum mean lift-coefficient characteristics at low tip Mach number and a limited amount of drag- divergence data at high tip Mach number of a helicopter rotor having an NACA 64(1)AO12 airfoil section and 8 deg of linear washout. Data are presented for blade tip Mach numbers M(t) of 0.29 to 0.74 with corresponding values 6 6 of tip Reynolds number of 2.59 x 10(exp 6) and 6.58 x 10(exp 6). Comparisons are made between the data from the present rotor with results previously obtained from two other rotors: one having NACA 0012 airfoil sections and the other having an NACA 0009 airfoil tip section. At low tip Mach numbers, the maximum mean lift coefficient for the blade having the NACA 64(1)AO12 section was about 0.08 less than that obtained with the blade having the NACA 0009 tip section and 0.21 less than the value obtained with the blade having the NACA 0012 tip section. Blade maximum mean lift coefficient values were not obtained for Mach number values greater than 0.47 because of a blade failure encountered during the tests. The effective mean lift-curve slope required for predicting rotor thrust varied from 5.8 for the tip Mach nuniber range of 0.29 to 0.55 to a value of 6.65 for a tip Mach number of 0.71. The blade pitching-moment coefficients were small and relatively unaffected by changes in thrust coefficient and Mach number. In the instances in which stall was reached, the break in the blade pitching-moment curve was in a stable direction. The efficiency of the rotor decreased with an increase in tip speed. Expressed as figure of merit, at a tip Mach number of 0.29 the maximum value was about 0.74. Similar measurements made on another rotor having an NACA 0012 airfoil and with a rotor having an NACA 0009 tip section, showed a value of 0.75. Synthesized section lift and profile-drag characteristics for the rotor-blade airfoil section are presented as an aid in predicting the high-tip-speed performance of rotors having similar airfoils.

Powell, Robert D., Jr.↗