Search NASA⌕ Search

SEARCH · Search NASA

Results for “IGNITION SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

A Low-Erosion Starting Technique for High-Performance Arcjets

The NASA arcjet program is currently sponsoring development of high specific impulse thrusters for next generation geosynchronous communications satellites (2 kW-class) and low-power arcjets for power limited spacecraft (approx. 0.5 kW-class). Performance goals in both of these efforts will require up to 1000 starts at propellant mass flow rates significantly below those used in state-of-the-art arcjet thruster systems (i.e., high specific power levels). Reductions in mass flow rate can lead to damaging modes of operation, particularly at thruster ignition. During the starting sequence, the gas dynamic force due to low propellant flow is often insufficient to rapidly push the arc anode attachment to its steady-state position in the diverging section of the nozzle. This paper describes the development and demonstration of a technique which provides for non-damaging starts at low steady-state flow rates. The technique employs a brief propellant pressure pulse at ignition to increase gas dynamic forces during the critical ignition/transition phase of operation. Starting characteristics obtained using both pressure-pulsed and conventional starting techniques were compared across a wide range of propellant flow rates. The pressure-pulsed starting technique provided reliable starts at mass flow rates down to 21 mg/s, typically required for 700 s specific impulse level operation of 2 kW thrusters. Following the comparison, a 600 start test was performed across a wide flow rate range. Post-test inspection showed minimal erosion of critical arcjet anode/nozzle surfaces.

Sankovic, John M.↗
NASA NTRS2010

A Completely New Type of Actuator -or- This Ain't Your Grandfather's Internal Combustion Engine

A completely new type of actuator - one that is proposed for use in a variety of environments from sea to land to air to space - has been designed, patented, built, and tested. The actuator is loosely based on the principle of the internal combustion engine, except that it is a completely closed system, only requiring electrical input, and the working fuel is water. This paper outlines the theory behind the electrolysis- and ignition-based cycle upon which the actuator operates and describes the performance capability test apparatus and results for the actuator. A mechanism application that harnessed the unit s power to twist a scaled rotor blade is also highlighted.

Gore, Brian W.↗
NASA NTRS1999

Testing of a Spray-Bar Zero Gravity Cryogenic Vent System for Upper Stages

The capability to vent in zero gravity without resettling is a fundamental technology need that involves practically all uses of subcritical cryogenics in space. Venting without resettling would extend cryogenic orbital transfer vehicle capabilities. However, the lack of definition regarding liquid/ullage orientation coupled with the somewhat random nature of the thermal stratification and resulting pressure rise rates, lead to significant technical challenges. Typically a zero gravity vent concept, termed a thermodynamic vent system (TVS), consists of a tank mixer to destratify the propellant, combined with a Joule- Thomson (J-T) valve to extract then-nal energy from the propellant. In a cooperative effort, Marshall Space Flight Center's (MSFC's) Multipurpose Hydrogen Test Bed (N4HTB) was used to test a unique "spray bar" TVS system developed by Boeing. A schematic of this system is included in Figure 1. The system consists of a recirculation pump, a parallel flow concentric tube, heat exchanger, and a spray bar positioned close to the longitudinal axis of the tank. In the mixing mode, the recirculation pump withdraws liquid from the tank and sprays it radially into the tank liquid, ullage, and exposed tank surfaces. When energy extraction is required, a small portion of the recirculated liquid is passed sequentially through the J-T expansion valve, the spray bar heat exchanger element, and is vented overboard. The vented vapor cools the circulated bulk fluid, thereby removing thermal energy and reducing tank pressure. Figure 2 is a plot of ullage pressure (P4) and liquid vapor pressure (PSAI) versus time. The pump operates alone, cycling on and off, to destratify the tank liquid and ullage until the liquid vapor pressure reaches the lower set point. At that point, the J-T valve begins to cycle on and off with the pump. Thus, for short duration missions, only the mixer may operate, thus minimizing or even eliminating boil-off losses. The primary advantage of the spray bar configuration is that pressure reduction is achieved independent of liquid and vapor location, thereby enhancing the applicability of normal gravity test data to zero gravity conditions. The in-tank components are minimized with the proposed TVS design. Because the recirculation pump is external to the tank, no electrical power penetration of the tank is required for pump or valve operation. This is especially desirable for L02 tanks since the presence of an electrical ignition source in oxygen represents a critical failure mode. Also, since the critical components (pump, motor, valve, orifice) are external to the tank, system checkout and ground servicing/replacement are easier. For zero-g operation, component replacement external to the tank may be a significant benefit. In addition to satisfying the zero g TVS design objectives, the TVS concept tested offers additional benefits to the integrated subcritical cryogenic storage and launch system.

Lak, Tibor↗
NASA NTRS1977

Current status of droplet and liquid combustion

The present understanding of spray combustion in rocket engine, gas turbine, Diesel engine and industrial furnace applications is reviewed. In some cases, spray combustion can be modeled by ignoring the details of spray evaporation and treating the system as a gaseous diffusion flame; however, in many circumstances, this simplification is not adequate and turbulent two-phase flow must be considered. The behavior of individual droplets is a necessary component of two-phase models and recent work on transient droplet evaporation, ignition and combustion is considered, along with a discussion of important simplifying assumptions involved with modeling these processes. Methods of modeling spray evaporation and combustion processes are also discussed including: one-dimensional models for rocket engine and prevaporized combustion systems, lumped zone models (utilizing well-stirred reactor and plug flow regions) for gas turbine and furnace systems, locally homogeneous turbulent models, and two-phase models. The review highlights the need for improved injector characterization methods, more information of droplet transport characteristics in turbulent flow and continued development of more complete two-phase turbulent models

Faeth, G. M.↗
NASA NTRS2011

Liquid Oxygen/Liquid Methane Propulsion and Cryogenic Advanced Development

Exploration Systems Architecture Study conducted by NASA in 2005 identified the liquid oxygen (LOx)/liquid methane (LCH4) propellant combination as a prime candidate for the Crew Exploration Vehicle Service Module propulsion and for later use for ascent stage propulsion of the lunar lander. Both the Crew Exploration Vehicle and Lunar Lander were part the Constellation architecture, which had the objective to provide global sustained lunar human exploration capability. From late 2005 through the end of 2010, NASA and industry matured advanced development designs for many components that could be employed in relatively high thrust, high delta velocity, pressure fed propulsion systems for these two applications. The major investments were in main engines, reaction control engines, and the devices needed for cryogenic fluid management such as screens, propellant management devices, thermodynamic vents, and mass gauges. Engine and thruster developments also included advanced high reliability low mass igniters. Extensive tests were successfully conducted for all of these elements. For the thrusters and engines, testing included sea level and altitude conditions. This advanced development provides a mature technology base for future liquid oxygen/liquid methane pressure fed space propulsion systems. This paper documents the design and test efforts along with resulting hardware and test results.

Klem, Mark D.↗
NASA NTRS2007

Ignition Characterization Test Results for the LO2/Ethanol Propellant Combination

A series of contracts were issued by the Marshall Space Flight Center (MSFC) of the National Aeronautics and Space Administration (NASA) un der the auspices of the Exploration Systems Mission Directorate to de velop and expand the maturity of candidate technologies considered to be important for future space exploration. One such technology was to determine the viability of incorporating non-toxic propellants for R eaction Control Subsystems (RCS). Contract NAS8-01109 was issued to A erojet to develop a dual thrust Reaction Control Engine (RCE) that ut ilized liquid oxygen and ethanol as the propellants. The dual thrust RCE incorporated a primary thrust level of 870 lbf, and a vernier thru st level of 10 - 30 lbf. The preferred RCS approach for the dual thru st RCE was to utilize pressure-fed liquid oxygen (LOX) and ethanol pr opellants; however, previous dual thrust feasibility testing incorporated GOX/Ethanol igniters as opposed to LOX/Ethanol igniters in the de sign. GOX/Ethanol was easier to ignite, but this combination had syst em design implications of providing GOX for the igniters. A LOX/Ethan ol igniter was desired; however, extensive LOX/Ethanol ignition data over the anticipated operating range for the dual thrust RCE did not e xist. Therefore, Aerojet designed and tested a workhorse LOX igniter to determine LOX/Ethanol ignition characteristics as part of a risk m itigation effort for the dual thrust RCE design. The objective of the ignition testing was to demonstrate successful ignition from GOX to LOX, encompassing potential two-phase flow conditions anticipated being present in real mission applications. A workhorse igniter was desig ned to accommodate the full LOX design flowrate, as well as a reduced GOX flowrate. It was reasoned that the initial LOX flow through the igniter would flash to GOX due to the latent heat stored in the hardwa re, causing a reduced oxygen flowrate because of a choked, or sonic, flow condition through the injection elements. As LOX flow continued, the hardware would chill-in, with the injected oxygen flow transitioning from cold GOX through two'phase flow to subcooled LOX. The Workh orse igniter was well instrumented: Pressure and temperature instrumentation permitted oxygen state points to be determined in the igniter oxidizer manifold, and gas-side igniter chamber thermocouples provide d chamber thermal profile characteristics. The cold flow chamber pres sure (Pc) for each test was determined and coupled with the igniter chamber diameter (De) to calculate the characteristic quench parameter (Pc x Dc), which was plotted as a function of core mixture ratio, MRc . Ignition limits were determined over a broad range of valve inlet conditions, and ignition was demonstrated with oxygen inlet conditions that ranged from subcooled 210 deg R LOX to 486 deg R GOX. Once ign ited at cold GOX conditions, combustion was continuous as the hardwar e chilled in and the core mixture ratio transitioned from values near 1.0 to over 12.5. Pulsing is required in typical RCS engines; therefore, the workhorse igniter was pulse tested to verify the ability to pr ovide the required ignition for a pulsing RCE. The minimum electrical pulse width (EPW) of the dual thrust RCE was 0.080 seconds. Igniter pulse tests were performed at three conditions: (1) an EPW of 0.080 se conds at 25% duty cycle for 400 pulses; (2) an EPW of 0.160 seconds a nd a 5% duty cycle for 124 pulses; (3) an EPW of 0.160 seconds and a 50% duty cycle for 380 pulses. Successful ignition of LOX/Ethanol was demonstrated over a broad range of valve inlet conditions, with the empirically determined LOX/Ethanol ignition limits extending the previous database established for GOX/Ethanol ignition limits. Although th e observed chill-in characteristics of the hardware varied significan tly with flowrate, ignition was readily achieved. Combustion was marg inal at extremely fuel-rich conditions, and it fluctuated as the oxygen passed rough the twophase flow regime during the period of hardware chill-in. Pulse testing showed good repeatability with 100 percent r e-ignition for all pulses. Certain pulse-to-pulse repeatability requirements for actual RCS operation may necessitate establishment of mini mum oxygen flow rates and engine thrust levels for satisfactory engin e performance.

Robinson, Philip J.↗
DOE OSTI2026

Numerical investigation of liquid wall ablation in inertial fusion energy chambers

This paper presents a novel approach for modeling liquid wall ablation in liquid wall-protected inertial fusion energy (IFE) chambers. These systems are promising candidates for the implementation of fusion technology, yet significant gaps remain in understanding the underlying physical processes and their implications for design. Following target ignition, a portion of the fusion energy is released as x-rays, which deposit their energy into an array of liquid jets, leading to partial vaporization. Accurately modeling this heat deposition and vaporization process remains challenging due to the complex geometries typical of (pre-conceptual) IFE chamber designs. Furthermore, the subsequent expansion of vaporized material into the chamber’s vacuum environment poses difficulties for conventional CFD methods based on continuum assumptions, which can lead to significant inaccuracies. To address some aspects of these challenges, this work introduces a ray-tracing-based methodology to map the spatial distribution of ablated material in liquid wall-protected systems. In addition, a vacuum-tracking scheme is developed to extend the applicability of an OpenFOAM-based solver to gas dynamics in rarefied environments. The proposed approach has been verified through numerical benchmarks and applied to a practical case involving the HYLIFE-II (High Yield Lithium Injection Fusion Energy) chamber. The methodology advances the modeling capabilities for liquid wall-protected IFE systems and provides valuable tools to support their design and optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

Mars Ascent Vehicle Hybrid Propulsion Effort

A technology development program was undertaken to determine if the benefits of hybrid rocket propulsion could be realized for a Mars Ascent Vehicle (MAV) application. Specifically, the goal of this program was to increase the Technology Readiness Level (TRL) of a hybrid propulsion system such that it could be considered for a potential Mars Sample Return Campaign. Over the course of approximately five years, a new, wax-based fuel was developed, characterized and tested with Mixed Oxides of Nitrogen (from MON-3 to MON-25). Various ignition mechanisms were tested and solid hypergolic additives were evaluated for their potential to ignite the hybrid motor. Several hot-fire test campaigns were completed at both sub- and full-scale. The technology development program was born out of a JPL study documented by Shotwell and Karp that identified the Single Stage to Orbit (SSTO) hybrid propulsion system for a potential Mars Ascent Vehicle to be the lowest Gross Lift Off Mass option from the ten configurations evaluated. Benefits of the hybrid option included its predicted favorable low temperature storage and operation behavior, high performance and ability to restart (enabling the SSTO). The main disadvantage of the hybrid option was its low TRL, as it essentially started as a blank sheet design with a new fuel development. Near the end of the technology development program, a Preliminary Architecture Assessment (PAA) was completed to evaluate a single-stage hybrid propulsion system and a two-stage solid propulsion system for a potential MAV. The solid propulsion system was selected for further study in 2019, primarily because of its flight heritage. While the hybrid technology development program made many strides, there was still a list of challenges to overcome. This paper will discuss the substantial progress and remaining challenges from the technology development effort from 2015 through 2019. This includes fuel development and reformulation, sub- and full-scale testing at Space Propulsion Group, full scale testing at Parabilis, full scale testing at Whittinghill Aerospace, hypergolic additive testing at Purdue and Penn State and the evaluation of adding hypergolic additives to a fullscale grain. It also includes a discussion of the design that resulted from the Preliminary Architecture Assessment.

hybrid rocket↗
NASA NTRS1988

Assessment, development, and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamcis codes have led to their application to complex 3-D flows such as those in the gas turbine combustor. A number of U.S. Government and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aerothermal Modeling and supporting programs are described.

Holdeman, J. D.↗
DOE OSTI2024

Toward digital design at the exascale: An overview of project ICECap

High performance computing has entered the Exascale Age. Capable of performing over 1018 floating point operations per second, exascale computers, such as El Capitan, the National Nuclear Security Administration's first, have the potential to revolutionize the detailed in-depth study of highly complex science and engineering systems. However, in addition to these kind of whole machine “hero” simulations, exascale systems could also enable new paradigms in digital design by making petascale hero runs routine. Currently, untenable problems in complex system design, optimization, model exploration, and scientific discovery could all become possible. Motivated by the challenge of uncovering the next generation of robust high-yield inertial confinement fusion (ICF) designs, project ICECap (Inertial Confinement on El Capitan) attempts to integrate multiple advances in machine learning (ML), scientific workflows, high performance computing, GPU-acceleration, and numerical optimization to prototype such a future. Built on a general framework, ICECap is exploring how these technologies could broadly accelerate scientific discovery on El Capitan. In addition to our requirements, system-level design, and challenges, we describe some of the key technologies in ICECap, including ML replacements for multiphysics packages, tools for human-machine teaming, and algorithms for multifidelity design optimization under uncertainty. As a test of our prototype pre-El Capitan system, we advance the state-of-the art for ICF hohlraum design by demonstrating the optimization of a 17-parameter National Ignition Facility experiment and show that our ML-assisted workflow makes design choices that are consistent with physics intuition, but in an automated, efficient, and mathematically rigorous fashion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Fusion burn-propagation simulations using the collisional and radiative particle-in-cell code TRIFORCE

The ability to accurately model burn propagation in inertial confinement fusion plasmas is crucial for advancing fusion energy research. This work presents enhancements to the triforce hybrid fluid-kinetic multiphysics code, focusing on its kinetic half, which employs the particle-in-cell (PIC) method with Monte Carlo collisions (MCC). We use a moment-preserving collision model that mitigates numerical noise, particularly in spherical geometries where particle weights vary significantly. Additionally, we refine the treatment of inverse bremsstrahlung to account for electron–ion collision frequency reductions in degenerate plasmas and incorporate a blackbody radiation source to enable realistic photon injection. These improvements enable the simulation of 1-dimensional (1D) spherical fusion burn propagation in deuterium–tritium plasmas. Benchmark comparisons with the hydra radiation-hydrodynamics code confirm that triforce accurately captures the dynamics of hot-spot expansion and burn propagation, demonstrating sensitivity to ignition thresholds consistent with theoretical models. Findings show the ignition cliff to be less steep in our work compared to radiation-hydrodynamic modeling. These results highlight the role of kinetic effects in fusion ignition physics and underscore the necessity of hybrid fluid-kinetic models for advancing predictive capabilities in high-energy-density plasma systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1982

Computer program for prediction of capture maneuver probability for an on-off reaction controlled upper stage

A FORTRAN coded computer program which computes the capture transient of a launch vehicle upper stage at the ignition and/or separation event is presented. It is for a single degree-of-freedom on-off reaction jet attitude control system. The Monte Carlo method is used to determine the statistical value of key parameters at the outcome of the event. Aerodynamic and booster induced disturbances, vehicle and control system characteristics, and initial conditions are treated as random variables. By appropriate selection of input data pitch, yaw and roll axes can be analyzed. Transient response of a single deterministic case can be computed. The program is currently set up on a CDC CYBER 175 computer system but is compatible with ANSI FORTRAN computer language. This routine has been used over the past fifteen (15) years for the SCOUT Launch Vehicle and has been run on RECOMP III, IBM 7090, IBM 360/370, CDC6600 and CDC CYBER 175 computers with little modification.

Knauber, R. N.↗
NASA NTRS2010

Altitude Testing of Large Liquid Propellant Engines

The National Aeronautics and Space Administration entered a new age on January 14, 2004 with President Bush s announcement of the creation the Vision for Space Exploration that will take mankind back to the Moon and on beyond to Mars. In January, 2006, after two years of hard, dedicated labor, engineers within NASA and its contractor workforce decided that the J2X rocket, based on the heritage of the Apollo J2 engine, would be the new engine for the NASA Constellation Ares upper stage vehicle. This engine and vehicle combination would provide assured access to the International Space Station to replace that role played by the Space Shuttle and additionally, would serve as the Earth Departure Stage, to push the Crew Excursion Vehicle out of Earth Orbit and head it on a path for rendezvous with the Moon. Test as you fly, fly as you test was chosen to be the guiding philosophy and a pre-requisite for the engine design, development, test and evaluation program. An exhaustive survey of national test facility assets proved the required capability to test the J2X engine at high altitude for long durations did not exist so therefore, a high altitude/near space environment testing capability would have to be developed. After several agency concepts the A3 High Altitude Testing Facility proposal was selected by the J2X engine program on March 2, 2007 and later confirmed by a broad panel of NASA senior leadership in May 2007. This facility is to be built at NASA s John C. Stennis Space Center located near Gulfport, Mississippi. 30 plus years of Space Shuttle Main Engine development and flight certification testing makes Stennis uniquely suited to support the Vision For Space Exploration Return to the Moon. Propellant handling infrastructure, engine assembly facilities, a trained and dedicated workforce and a broad and varied technical support base will all ensure that the A3 facility will be built on time to support the schedule needs of the J2X engine and the ultimate flight of the first Ares I vehicle. The A3 facility will be able to simulate pre-ignition altitude from sea-level to 100,000 feet and maintain it up to 650 seconds. Additionally the facility will be able to accommodate initial ignition, shutdown and then restart test profiles. A3 will produce up to 5000 lbm/sec of superheated steam utilizing a Chemical Steam generation system. Two separate inline steam ejectors will be used to produce a test cell vacuum to simulate the 100,000 ft required altitude. Operational capability will ensure that the facility can start up and shutdown without producing adverse pressure gradients across the J2X nozzle. The facility will have a modern thrust measurement system for accurate determination of engine performance. The latest advances in data acquisition and control will be incorporated to measure performance parameters during hotfire testing. Provisions are being made in the initial design of the new altitude facility to allow for testing of other, larger engines and potential upper stage launch vehicles that might require vacuum start testing of the engines. The new facility at Stennis Space Center will be complete and ready for hotfire operations in late 2010.

Maynard, Bryon T.↗
NASA NTRS2009

Solar Wind Ablation of Terrestrial Planet Atmospheres

Internal plasma sources usually arise in planetary magnetospheres as a product of stellar ablation processes. With the ignition of a new star and the onset of its ultraviolet and stellar wind emissions, much of the volatiles in the stellar system undergo a phase transition from gas to plasma. Condensation and accretion into a disk is replaced by radiation and stellar wind ablation of volatile materials from the system- Planets or smaller bodies that harbor intrinsic magnetic fields develop an apparent shield against direct stellar wind impact, but UV radiation still ionizes their gas phases, and the resulting internal plasmas serve to conduct currents to and from the central body along reconnected magnetic field linkages. Photoionization and thermalization of electrons warms the ionospheric topside, enhancing Jeans' escape of super-thermal particles, with ambipolar diffusion and acceleration. Moreover, observations and simulations of auroral processes at Earth indicate that solar wind energy dissipation is concentrated by the geomagnetic field by a factor of 10-100, enhancing heavy species plasma and gas escape from gravity, and providing more current carrying capacity. Thus internal plasmas enable coupling with the plasma, neutral gas and by extension, the entire body. The stellar wind is locally loaded and slowed to develop the required power. The internal source plasma is accelerated and heated, inflating the magnetosphere as it seeks escape, and is ultimately blown away in the stellar wind. Bodies with little sensible atmosphere may still produce an exosphere of sputtered matter when exposed to direct solar wind impact. Bodies with a magnetosphere and internal sources of plasma interact more strongly with the stellar wind owing to the magnetic linkage between the two created by reconnection.

Moore, Thomas Earle↗
NASA NTRS1988

Assessment, development and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between: combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamics (CFD) codes have led to their application to complex three-dimensional flows such as those in the gas turbine combustor. A number of US. Government and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aerothermal Modeling and supporting programs are described in this paper.

Aerothermal modeling↗
NASA NTRS1989

Assessment, development, and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between: combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamics (CFD) codes have led to their application to complex three-dimensional flows such as those in the gas turbine combustor. A number of U.S. Govern- ment and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aero- thermal Modeling and supporting programs are described in this paper

J D Holdeman↗
NASA NTRSDate not supplied

Mars Ascent Vehicle Hybrid PropulsionEffort

A technology development program was undertaken to determine if the benefits of hybrid rocket propulsion could be realized for a Mars Ascent Vehicle (MAV) application. Specifically, the goal of this program was to increase the Technology Readiness Level (TRL) of a hybrid propulsion system such that it could be considered for a potential Mars Sample Return Campaign. Over the course of approximately five years, a new, wax-based fuel was developed, characterized and tested with Mixed Oxides of Nitrogen (from MON-3 to MON-25). Various ignition mechanisms were tested and solid hypergolic additives were evaluated for their potential to ignite the hybrid motor. Several hot-fire test campaigns were completed at both sub- and full-scale. The technology development program was born out of a JPL study documented by Shotwell and Karp that identified the Single Stage to Orbit (SSTO) hybrid propulsion system for a potential Mars Ascent Vehicle to be the lowest Gross Lift Off Mass option from the ten configurations evaluated. Benefits of the hybrid option included its predicted favorable low temperature storage and operation behavior, high performance and ability to restart (enabling the SSTO). The main disadvantage of the hybrid option was its low TRL,as it essentially started as a blank sheet design with a new fuel development. Near the end of the technology development program, a Preliminary Architecture Assessment (PAA) was completed to evaluate a single-stage hybrid propulsion system and a two-stage solid propulsion system for a potential MAV. The solid propulsion system was selected for further study in 2019, primarily because of its flight heritage. While the hybrid technology development program made many strides, there was still a list of challenges to overcome. This paper will discuss the substantial progress and remaining challenges from the technology development effort from 2015 through 2019. This includes fuel development and reformulation, sub- and full-scale testing at Space Propulsion Group, full scale testing at Parabilis, full scale testing at Whittinghill Aerospace, hypergolic additive testing at Purdue and Penn State and the evaluation of adding hypergolic additives to a full-scale grain. It also includes a discussion of the design that resulted from the Preliminary Architecture Assessment.

hybrid rocket↗
NASA NTRS2000

Magnetic Flux Compression Concept for Nuclear Pulse Propulsion and Power

The desire for fast, efficient interplanetary transport requires propulsion systems having short acceleration times and very high specific impulse attributes. Unfortunately, most highly efficient propulsion systems which are within the capabilities of present day technologies are either very heavy or yield very low impulse such that the acceleration time to final velocity is too long to be of lasting interest, One exception, the nuclear thermal thruster, could achieve the desired acceleration but it would require inordinately large mass ratios to reach the range of desired final velocities. An alternative approach, among several competing concepts that are beyond our modern technical capabilities, is a pulsed thermonuclear device utilizing microfusion detonations. In this paper, we examine the feasibility of an innovative magnetic flux compression concept for utilizing microfusion detonations, assuming that such low yield nuclear bursts can be realized in practice. In this concept, a magnetic field is compressed between an expanding detonation driven diamagnetic plasma and a stationary structure formed from a high temperature superconductor (HTSC). In general, we are interested in accomplishing two important functions: (1) collimation of a hot diamagnetic plasma for direct thrust production; and (2) pulse power generation for dense plasma ignition. For the purposes of this research, it is assumed that rnicrofusion detonation technology may become available within a few decades, and that this approach could capitalize on recent advances in inertial confinement fusion ICF) technologies including magnetized target concepts and antimatter initiated nuclear detonations. The charged particle expansion velocity in these detonations can be on the order of 10 (exp 6)- 10 (exp 7) meters per second, and, if effectively collimated by a magnetic nozzle, can yield the Isp and the acceleration levels needed for practical interplanetary spaceflight. The ability to ignite pure fusion micro-bursts with reasonable levels of input energy is an equally challenging scientific problem. It remains to be seen, however, whether an effective ignition driver can be developed which meets the requirements for practical spaceflight application (namely high power density, compactness, low weight, and low cost). In this paper, system level performance and design issues are examined including generator performance, magnetic flux compression processes, magnetic diffusion processes, high temperature superconductor (HTSC) material properties, plasmadynamic processes, detonation plasma expansion processes, magnetohydrodynamic instabilities, magnetic nozzle performance, and thrust production performance. Representative generator performance calculations based on a simplified skin layer formulation are presented as well as the results of exploratory small-scale laboratory experiments on magnetic flux diffusion in HTSC materials. In addition, planned follow-on scientific feasibility experiments are described which utilize high explosive detonations and high energy gas discharges to simulate the plasma conditions associated with thermonuclear micro-detonations.

Litchford, Ronald J.↗