Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT TESTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Bayesian calibration of a physics-based crystal plasticity and damage model

In this work, we present a model parameter calibration procedure for a physics-based crystal plasticity model. The calibration process utilizes a powerful statistics-based Bayesian calibration method. Calibration of the crystal plasticity parameters makes use of experimentally-measured data, i.e. compressive stress–strain response, from $\langle$100$\rangle$ and $\langle$123$\rangle$ single crystal copper dynamically loaded via Kolsky bar tests. The calibration of damage parameters is achieved using experimentally-measured free-surface velocity history data from plate impact test on $\langle$100$\rangle$ and $\langle$110$\rangle$ single crystal copper, which generates shock compression followed by dynamic tensile failure. A validation assessment is then carried out by comparing the calibrated model predictions and experimental measurements of the dynamic tensile damage generated in an impacted bicrystal copper plate. Lastly, a model-informed rationale for the experimentally-observed dependence of the spatial distribution of ductile damage (porosity) on crystallography is provided.

42 ENGINEERING↗

Contact force history and dynamic response due to the impact of a soft projectile

A series of ballistic impact tests on several different instrumented targets was performed to characterize the dynamic contact force history resulting from the impact of a compliant projectile. The results show that the variation of contact force history with impact velocity does not follow the trends predicted by classical impact models. An empirical model was therefore developed to describe this behavior. This model was then used in a finite-element analysis to estimate the force history and calculate the resulting dynamic strain response in a transversely impacted composite laminate.

Grady, J. E.↗

Test methods for determining the suitability of metal alloys for use in oxygen-enriched environments

Materials are more flammable in oxygen rich environments than in air. When the structural elements of a system containing oxygen ignite and burn, the results are often catastrophic, causing loss of equipment and perhaps even human lives. Therefore, selection of the proper metallic and non-metallic materials for use in oxygen systems is extremely important. While test methods for the selection of non-metallic materials have been available for years, test methods for the selection of alloys have not been available until recently. Presented here are several test methods that were developed recently at NASA's White Sands Test Facility (WSTF) to study the ignition and combustion of alloys, including the supersonic and subsonic speed particle impact tests, the frictional heating and coefficient of friction tests, and the promoted combustion test. These test methods are available for commercial use.

Stoltzfus, Joel M.↗

STANDARD REFERENCE MATERIAL CHARPY TESTING FROM HIGH FLUENCE SURVEILLANCE CAPSULE

The Palisades Nuclear Generating Station included in its original surveillance program a surveillance capsule, designated A-60. The capsule was removed from its surveillance position in early 1995 and has been resident in the spent fuel pool since that time. It was harvested to perform characterization of surveillance specimens in this capsule in 2023. This capsule was irradiated to a fluence of 1.96x1020 n/cm2 (E> 1MeV) that is equivalent for more than 150 effective full power years for the current US reactor pressure vessel (RPV) fleet. This capsule contained several materials, including Charpy specimens of standard reference material (SRM) from Heavy-Section Steel Technology (HSST) A533-B Plate 01. To perform Charpy testing of this highly irradiated material, the new Charpy specimen transfer system was designed and implemented on Charpy impact testing machine in the hot cell to accommodate remote testing of these specimens. This new transfer system includes integrated environmental chamber to cool or heat Charpy specimens to the desired temperature. Testing of this highly irradiated material revealed very large shift of Charpy transition temperature, 188oC.

Sokolov, Mikhail [ORNL] (ORCID:0000000256373346)↗

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch- and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 0 dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time throughout the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 300 dead-rise model tests, C(sub Delta)A = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor ofC(sub Delta). For instance, the maximum impact lift coefficient C(sub L,max)is found to be directly proportional to C(sub Delta)(sup 0.33) for the flat-bottom model and C(sub Delta)(sup 0.45) for the 30 deg dead-rise model. These variations of C(sub L,max) C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L,max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to 30 deg, beam-loading coefficients from 0.48 to 544, trim angles from 3 deg to 45 deg and initial flight-path angles from about 2 deg to about 27 deg.

Mixson, John S.↗

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch-and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 deg dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time through- out the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 30 deg dead-rise model tests, C(sub Delta) = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor of C(sub Delta). For instance, the maximum impact lift coefficient is found C(sub L,max) to be directly proportional to C(sub Delta, exp 0,33) for the flat-bottom model and C(sub Delta, exp 0,45) for the 30 deg dead-rise model. These variations of C(sub L, max) with C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L, max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to deg, beam-loading coefficients from o.48 to 544, trim angles from 3 deg to deg, and initial flight-path angles from about 2 deg to about deg.

Mixson, John S.↗

Evaluation of Contaminant-Promoted Ignition in Scuba Equipment and Breathing Gas Delivery Systems

As the underwater diving industry continues to use greater concentrations of oxygen in their scuba systems, ignition of contaminants in these systems becomes a greater concern. Breathing gas makeup and distribution systems typically combine pure oxygen with various diluents to supply high-pressure cylinders for scuba applications. The hazards associated with these applications of oxygen and NITROX (oxygen and nitrogen mixture) gases require an evaluation of inherent contaminant levels and their associated promoted-ignition thresholds in these environments. In this study, several scuba component assemblies were tested after one year of use at the NASA Johnson Space Center Neutral Buoyancy Lab. The components were rapidly impacted with 50% NITROX gas to demonstrate their ignition resistance, then disassembled to evaluate their cleanliness. A follow-up study was then performed on the ignition thresholds of hydrocarbon-bascd oil films in oxygen and NITROX environments in an attempt to define the cleaning requirements for these systems. Stainless steel tubes were contaminated and verified to known levels and placed in a pneumatic impact test system where they were rapidly pressurized with the test gas. Ignitions were determined using a photodiode connected to the end of the contaminated tube. The results of the scuba component tests, cleanliness evaluation, and contaminant ignition study are discussed and compared for 50% NITROX and 100% oxygen environments.

Forsyth, Elliott T.↗

Assessment of Potential Dose and Environmental Impacts from Proposed Testing at the INL National Security Test Range

This assessment uses screening level models to calculate potential environmental impacts from proposed tests at two locations at the Idaho National Laboratory (INL) National Security Test Range (NSTR) site. Proposed tests could be conducted using 11 different radioactive material types that include K 2 O, LaBr 3 , KBr, Cu, Zr, F, Ga, Ga 2 O 3 , NaNO 2 , Ga-68, and Tc-99m. The tests could potentially release radioactive material to the atmosphere and radionuclides and other contaminants to the soil, which could leach into the unsaturated zone and migrate to the aquifer. Atmospheric transport of radionuclides to potential human receptors and time-integrated air concentrations were calculated with a Gaussian plume model and three years of hourly meteorological data. Potential surface soil impacts were calculated with the computer program Mixing-Cell Model (MCM). Groundwater impacts were calculated with the computer programs MCM and GWSCREEN. Radiological doses from potential atmospheric releases were calculated for public receptors off the INL Site and for workers at nearby INL facilities. Results were compared to regulatory dose limits. Maximum potential groundwater concentrations were estimated in the aquifer below the NSTR site and compared to drinking water standards or risk-based screening levels for resident tap water. Soil concentrations were calculated and compared to risk-based screening levels for workers and potential future residents. All impacts were estimated based on the assumption that 12 tests are conducted annually using all 11 material types for 15 years. This document provides the resources to enable a subject matter expert in the field of environmental assessments to replicate the modeling and calculations. The methodology and parameters are presented in the text. All electronic files, including computer code input, output, executable files, batch files, scripts, and spreadsheet files, are contained in a zip file that can be accessed by selecting “Additional Information” (select Native File) in the INL Electronic Document Management System (EDMS).

99 GENERAL AND MISCELLANEOUS↗

Initial Examination of Low Velocity Sphere Impact of Glass Ceramics

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) sphere impact testing of two materials from the lithium aluminosilicate family reinforced with different amounts of ceramic particulate, i.e., glass-ceramic materials, SCHOTT Resistan™-G1 and SCHOTT Resistan™-L. Both materials are provided by SCHOTT Glass (Duryea, PA). This work is a follow-up to similar sphere impact studies completed by the authors on PPG's Starphire® soda-lime silicate glass and SCHOTT BOROFLOAT® borosilicate glass. A gas gun or a sphere-drop test setup was used to produce controlled velocity delivery of silicon nitride (Si 3 N 4 ) spheres against the glass ceramic tile targets. Minimum impact velocities to initiate fracture in the glass-ceramics were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan™-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire® soda-lime silicate glass was second best, then Resistan™-G1 glass ceramic, and then BOROFLOAT® borosilicate glass. (2) Glass-ceramic Resistan™-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire® soda-lime silicate glass, Resistan™-G1 glass ceramic, and BOROFLOAT® borosilicate glass. (3) Spheres with a lower elastic modulus require less force to initiate fracture in Resistan™-G1 from quasi-static spherical indentation. This indicates that friction is affecting ring crack initiation in Resistan™-G1. Friction also affected ring crack initiation in Starphire® soda-lime silicate and BOROFLOAT® borosilicate glasses. Among these three materials, friction was the most pronounced (largest slope in the RCIF-elastic modulus graph) in the Starphire® and least pronounced in the BOROFLOAT®. The reason for this is not understood, but differences in deformation behavior under high contact stresses could be a cause or contributor to this. (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than it is under quasi-static conditions in Resistan™-L and Resistan™-G1 glass ceramics. This is a trend observed too in Starphire® and BOROFLOAT®. (5) There is a subtle indication there was intra-tile differences in spherical indentation-induced ring crack initiation forces. This is not a material property nor is it exclusive to glass-ceramic Resistan™-G1 glass ceramic, rather, it is a statistical mechanical response to an accumulated history of processing and handling of that specific tile.

36 MATERIALS SCIENCE↗

Evaluation of Surlyn 8920 as PHE Visor Material and Evaluations of New Adhesives for Improving Bonding Between Teflon and Stainless Steel at Cryogenic Temperature

Two studies are presented, and in the first study, Surlyn 8920 (an ionic and amorphous low density polyethylene made by Dupont) was evaluated as a possible replacement of Plexyglass G as PHE visor material. Four formulations of the polymer were made by adding different amounts of UV stabilizer, energy quencher, and antioxident in a Brabender Plasticorder. The formulated polymers were molded in the form of sheets in a compression molder. Cut samples from the molded sheets were exposed in a weatherometer and tested on Instron Tensile Tester for strength and elongation. Specially molded samples of the formulated polymers were subjected to Charpy Impact Tests. In the second study, preliminary evaluations of adhesives for improvement of bonding between Teflon and stainless steel (SS) were performed. Kapton, a high temperature polyimide made by Dupont, and a rubber based adhesive made by Potter Paint Co., were evaluated against industrial quality epoxy, the current material used to bond Teflon and SS. The degreased surfaces of the SS discs were etched mechanically, with a few of these etched chemically. The surfaces of the SS discs were etched mechanically, with a few of these etched chemically. Bonding strengths were evaluated using lap shear tests on the Instron Tensile Tester for the samples bonded by Kapton and industrial quality epoxy. Bond strengths were also evaluated using a pull test on the Instron for the samples bonded by Potter adhesive (CWL-152) and industrial quality epoxy. Based on limited lap shear data, Kapton gave bond strength favorable compared to that of industrial epoxy. Based on limited pull test data, Kapton bonded and CWL-152 bonded samples showed poor strength compared to epoxy bonded sample.

Ray, Asit K.↗

Ballistic Impact of Braided Composites with a Soft Projectile

Impact tests using a soft gelatin projectile were performed to identify failure modes that occur at high strain energy density during impact loading. Failure modes were identified for aluminum plates and for composites plates and half-rings made from triaxial carbon fiber braid having a 0/+/- 60deg architecture. For aluminum plates, a large hole formed as a result of crack propagation from the initiation site at the center of the plate. For composite plates, fiber tensile failure occurred in the back ply at the center of the plate. Cracks then propagated from this site along the +/-60deg fiber directions until triangular flaps opened to form a hole. For composite half-rings fabricated with 0deg fibers aligned circumferentially, fiber tensile failure also occurred in the back ply. Cracks first propagated from this site perpendicular the 0deg fibers. The cracks then turned to follow the +/-60deg fibers and 0deg fibers until rectangular flaps opened to form a hole. Damage in the composites was localized near the impact site, while cracks in the aluminum extended to the boundaries.

Roberts, Gary D.↗

Lunar Meteoroid Impact Observations and the Flux of Kilogram-sized Meteoroids

Lunar impact monitoring provides useful information about the flux of meteoroids in the hundreds of grams to kilograms size range. The large collecting area of the night side of the lunar disk, approximately 3.8 10(exp 6)sq km in our camera field-of-view, provides statistically significant counts of the meteoroids striking the lunar surface. Over 200 lunar impacts have been observed by our program in roughly 4 years. Photometric calibration of the flashes observed in the first 3 years along with the luminous efficiency determined using meteor showers and hypervelocity impact tests (Bellot Rubio et al. 2000; Ortiz et al. 2006; Moser et al. 2010; Swift et al. 2010) provide their impact kinetic energies. The asymmetry in the flux on the evening and morning hemispheres of the Moon is compared with sporadic and shower sources to determine their most likely origin. These measurements are consistent with other observations of large meteoroid fluxes.

Suggs, R. M.↗

An Overview of NASA’s Newest Engineering Model, ORDEM 4.0

Since the mid-1990s, one of the most important products produced by the NASA Orbital Debris Program Office (ODPO) has been the Orbital Debris Engineering Model (ORDEM). This series of models distills down our knowledge of the orbital debris environment to compute debris fluxes on satellites in a given orbit. This information can be used by spacecraft and upper stage designers and operators to design missions for better protection against the debris environment. The current version of the model is ORDEM 3.2, but the ODPO is working on the next generation of ORDEM, to be designated ORDEM 4.0. ORDEM 4.0 will include many known features from previous models, such as the ability to input a spacecraft orbit and time and to compute the flux as a function of debris size, impact speed, impact direction, and debris material densities, as well as uncertainty information on the flux. ORDEM 4.0 will update debris populations using the most recent measurements, including radar observations by the Haystack Ultrawideband Satellite Imaging Radar (HUSIR), NASA’s Goldstone radar, data from the new Space Surveillance Network Space Fence, and observations of Geosynchronous Earth Orbits (GEO) using the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT). The latest in situ impact data from returned hardware surfaces will be used. In addition, ORDEM 4.0 will introduce a parameterized debris shape model based on laboratory hypervelocity impact tests, such as DebriSat. This will allow analysts to implement shape characteristics in their damage equations and more accurately predict impact damage risk by debris of different shapes and orientations. This paper provides an overview of some of the new features forthcoming in ORDEM 4.0 and a status report on its development.

Mark Matney↗

An Overview of NASA’s Newest Engineering Model, ORDEM 4.0

Since the mid-1990s, one of the most important products produced by the NASA Orbital Debris Program Office (ODPO) has been the Orbital Debris Engineering Model (ORDEM). This series of models distills down our knowledge of the orbital debris environment to compute debris fluxes on satellites in a given orbit. This information can be used by spacecraft and upper stage designers and operators to design missions for better protection against the debris environment. The current version of the model is ORDEM 3.2, but the ODPO is working on the next generation of ORDEM, to be designated ORDEM 4.0. ORDEM 4.0 will include many known features from previous models, such as the ability to input a spacecraft orbit and time and to compute the flux as a function of debris size, impact speed, impact direction, and debris material densities, as well as uncertainty information on the flux. ORDEM 4.0 will update debris populations using the most recent measurements, including radar observations by the Haystack Ultrawideband Satellite Imaging Radar (HUSIR), NASA’s Goldstone radar, data from the new Space Surveillance Network Space Fence, and observations of Geosynchronous Earth Orbits (GEO) using the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT). The latest in situ impact data from returned hardware surfaces will be used. In addition, ORDEM 4.0 will introduce a parameterized debris shape model based on laboratory hypervelocity impact tests, such as DebriSat. This will allow analysts to implement shape characteristics in their damage equations and more accurately predict impact damage risk by debris of different shapes and orientations. This paper provides an overview of some of the new features forthcoming in ORDEM 4.0 and a status report on its development.

Mark Matney↗

Best Practices for Crash Modeling and Simulation

Aviation safety can be greatly enhanced by the expeditious use of computer simulations of crash impact. Unlike automotive impact testing, which is now routine, experimental crash tests of even small aircraft are expensive and complex due to the high cost of the aircraft and the myriad of crash impact conditions that must be considered. Ultimately, the goal is to utilize full-scale crash simulations of aircraft for design evaluation and certification. The objective of this publication is to describe "best practices" for modeling aircraft impact using explicit nonlinear dynamic finite element codes such as LS-DYNA, DYNA3D, and MSC.Dytran. Although "best practices" is somewhat relative, it is hoped that the authors' experience will help others to avoid some of the common pitfalls in modeling that are not documented in one single publication. In addition, a discussion of experimental data analysis, digital filtering, and test-analysis correlation is provided. Finally, some examples of aircraft crash simulations are described in several appendices following the main report.

Fasanella, Edwin L.↗

Ballistic Impact Response of Kevlar 49 and Zylon under Conditions Representing Jet Engine Fan Containment

A ballistic impact test program was conducted to provide validation data for the development of numerical models of blade out events in fabric containment systems. The impact response of two different fiber materials - Kevlar 49 (E.I. DuPont Nemours and Company) and Zylon AS (Toyobo Co., Ltd.) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation and velocity of the projectile were varied and recorded. In most cases the tests were designed such that the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models for predicting the response of fabrics under conditions simulating those of a jet engine blade release situation. In addition some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different materials.

Pereira, J. Michael↗

Effect of low-velocity or ballistic impact damage on the strength of thin composite and aluminum shear panels

Impact tests were conducted on shear panels fabricated from 6061-T6 aluminum and from woven fabric prepreg of Du Pont Kevlara fiber/epoxy resin and graphite fiber/epoxy resin. The shear panels consisted of three different composite laminates and one aluminum material configuration. Three panel aspect ratios were evaluated for each material configuration. Composite panels were impacted with a 1.27-cm (0.05-in) diameter aluminum sphere at low velocities of 46 m/sec (150 ft/sec) and 67 m/sec (220 ft/sec). Ballistic impact conditions consisted of a tumbled 0.50-caliber projectile impacting loaded composite and aluminum shear panels. The results of these tests indicate that ballistic threshold load (the lowest load which will result in immediate failure upon penetration by the projectile) varied between 0.44 and 0.61 of the average failure load of undamaged panels. The residual strengths of the panels after ballistic impact varied between 0.55 and 0.75 of the average failure strength of the undamaged panels. The low velocity impacts at 67 m/sec (220 ft/sec) caused a 15 to 20 percent reduction in strength, whereas the impacts at 46 m/sec (150 ft/sec) resulted in negligible strength loss. Good agreement was obtained between the experimental failure strengths and the predicted strength with the point stress failure criterion.

Farley, G. L.↗