SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The physical implications of modeling a subsonic boundary in an internal flow with a bump are discussed with reference to the effects of three different models. A numerical treatment of the corners is presented.
The analytical procedures described in NASA CR-150162 were extended for the purpose of analyzing the data from the first static test of the Solid Rocket Booster for the Space Shuttle. The component of thrust associated with the rapid changes in the internal flow field was calculated. This dynamic thrust component was shown to be prominent during flame spreading. An approach was implemented to account for the close coupling between the igniter and head end segment of the booster. The tips of the star points were ignited first, followed by radial and longitudinal flame spreading.
Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without internal flow separation. Experimental and analytical investigations were conducted to evaluate the effectiveness of tangential blowing to maintain attached flow to high angles of attack. The inlet had a relatively thin lip with a blowing slot located either on the lip or in the diffuser. The height and width of these slots was varied. Experimentally determined flow separation boundaries showed that lip blowing achieved higher angle of attack capability than diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. Predicted (analytical) separation boundaries showed good agreement except at the highest angles of attack.
Detailed pitot, static and wall pressure measurements have been obtained for a transonic normal shock wave/turbulent boundary layer interaction at free-stream Mach numbers of 1.28, 1.37 and 1.48 and at a constant unit Reynolds number of 4.92 x 10 to the 6th per meter in an axisymmetric, internal flow. Measurements have also been obtained at a unit Reynolds number of 9.84 x 10 to the 6th per meter at a free-stream Mach number of 1.29. The interaction depends very strongly on the Mach number. The effect of Reynolds number under study is small. Flow confinement due to the wind-tunnel wall boundary layer produces a weaker interaction and a much larger supersonic tongue than is observed for planar flows. Comparisons are made with solutions to the time-dependent, mass-averaged, Navier-Stokes equations incorporating a two-equation, Wilcox-Rubesin turbulence model (1980). The computations are in agreement with the experimental results.
Several two- and three-dimensional external and internal flow problems solved on the STAR-100 and CYBER-203 vector processing computers are described. The flow field was described by the full Navier-Stokes equations which were then solved by explicit finite-difference algorithms. Problem results and computer system requirements are presented. Program organization and data base structure for three-dimensional computer codes which will eliminate or improve on page faulting, are discussed. Storage requirements for three-dimensional codes are reduced by calculating transformation metric data in each step. As a result, in-core grid points were increased in number by 50% to 150,000, with a 10% execution time increase. An assessment of current and future machine requirements shows that even on the CYBER-205 computer only a few problems can be solved realistically. Estimates reveal that the present situation is more storage limited than compute rate limited, but advancements in both storage and speed are essential to realistically calculate three-dimensional flow.
A quantitative study of some nonlinear aspects of drop-shape oscillations in a liquid-liquid system has been completed. The results suggest a soft nonlinearity in the fundamental resonant mode frequency as the oscillation amplitude is increased. Indications of an increase in the rate of decay have also been obtained. A study of the internal flow fields has revealed patterns of circulation not present at low amplitude.
Turbomachinery system components and associated technologies are discussed. Specific technologies reviewed include the compressor, turbine, internal flow analysis methods, combustion, fuels, materials, structures, bearings, seals, and lubrication, dynamics and controls, and instrumentation. Analytical procedures as a path to improved performance are discussed. The strong interaction between the various technologies if turbomachinery performance gains are to be realized is reflected.
A series of air-breathing missile configurations was investigated to provide a data base for the design of such missiles. The model could be configurated with either twin axisymmetric or two dimensional inlets. Three circumferential inlet locations were investigated: 90 deg, 115 deg, and 135 deg from the top center. Two vertical wing locations, as well as wingless configurations, were used. Three tail configurations were formed by locating the tail surfaces either on the inlet fairing or on the inlet fairing or on fairings on the body. The surfaces were used to provide pitch control. Two dimensional inlets with extended compression surfaces, used to improve the angle-of-attack performance of the inlets for wingless configurations, were also investigated. The twin axisymmetric two dimensional inlet types without internal flow are covered, and the boost configuration of an air-breathing missile is simulated.
A centrifugal compressor facility being built by the NASA Lewis Research Center is described; its purpose is to obtain benchmark experimental data for internal flow code verification and modeling. The facility will be heavily instrumented with standard pressure and temperature probes and have provisions for flow visualization and laser Doppler velocimetry. The facility will accommodate rotational speeds to 2400 rpm and will be rated at pressures to 1.25 atm. The initial compressor stage for testing is geometrically and dynamically representative of modern high-performance stages with the exception of Mach number levels. Design exit tip speed for the initial stage is 500 ft/sec with a pressure ratio of 1.17. The rotor exit backsweep is 55 deg from radial.
Turbomachinery system component research to advance the technology of aviation turbofan and turbojet engines is discussed. Areas of research include compressors, turbines, internal flow analysis, combustion, fuels, materials, structures, bearings, seals, lubrication, dynamics and controls, and instrumentation. A review of the research directions being taken in these areas and the steady advances being made provides a reasonable glimpse at gas turbine technology of the future.
A new centrifugal compressor facility being built by the NASA Lewis Research Center is described; its purpose is to obtain 'benchmark' experimental data for internal flow code verification and modeling. The facility will be heavily instrumented with standard pressure and temperature probes and have provisions for flow visualization and laser Doppler velocimetry. The facility will accommodate rotational speeds to 2400 rpm and will be rated at pressures to 1.25 atm. The initial compressor stage for testing is geometrically and dynamically representative of modern high-performance stages with the exception of Mach number levels. Design exit tip speed for the initial stage is 500 ft/sec with a pressure ratio of 1.17. The rotor exit backsweep is 55 deg from radial. The facility is expected to be operational in the first half of 1985.
Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without the severe internal flow separation that can cause sudden changes in engine thrust, excessively high fan blade stresses, and possibly core-compressor stall. An experimental investigation was conducted to evaluate the effectiveness of tangential blowing to maintain attached flow at high inlet angles of attack. The inlet had a relatively thin lip (lip contraction ratio of 1.46). Two blowing slot locations were investigated: one on the lip and the other in the diffuser. The effect of two slot heights (0.0508 and 0.152 cm) and three slot circumferential extents, the largest being 120 deg, also was investigated. The results showed that both lip and diffuser blowing were effective in maintaining attached flow at high angles of attack. However, higher angle-of-attack capability was achieved with lip blowing than with diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. The tests were conducted in a low-speed wind tunnel at free-stream velocities between 18 and 62 m/sec and inlet angles of attack to 110 deg.
The results of the detail design of the Nacelle for the General Electric Energy Efficient Engine (E3) Integrated Core Low Spool (ICLS) test vehicles are presented. A slave nacelle is designed for the ICLS test. Cost and reliability are the important factors considered. The slave nacelle simulates the internal flow lines of the actual Flight Propulsion System (FPS) but has no external fairing. The aerodynamic differences between the ICLS and FPS nacelles are presented, followed by the structural description and analysis of the various nacelle components.
Future gas turbine technology will be based on contributions to the technology base being made today. At the NASA Lewis Research Center in Cleveland, OH, research is being conducted on turbomachinery system components and in a number of associated disciplines to advance the technology of aviation turbofan and torbojet engines. Areas of research include compressors, turbines, internal flow analysis, combustion, fuels, materials, structures, bearings, seals, lubrication, dynamics and controls, and instrumentation. A review of the research directions being taken in these areas and the steady advances being made provides a reasonable glimpse at gas turbine technology of the future.
The development of a computer code to generate numerical grids for complex internal flow systems such as the fluid flow inside the space shuttle main engine is outlined. The blending technique for generating a grid for stator-rotor combination at a particular radial section is examined. The computer programs which generate these grids are listed in the Appendices. These codes are capable of generating grids at different cross sections and thus providng three dimensional stator-rotor grids for the turbomachinery of the space shuttle main engine.
Fundamental equations encountered in computational fluid dynamics (CFD), and analyses used for internal flow are introduced. Irrotational flow; Euler equations; boundary layers; parabolized Navier-Stokes equations; and time averaged Navier-Stokes equations are treated. Assumptions made and solution methods are outlined, with examples. The overall status of CFD in propulsion is indicated.
A review of several applications of Computational Fluid Dynamics (CFD) to various aspects of aerodynamic design recently carried out at Grumman is presented. The emphasis is placed on project-oriented applications where the ease of use of the methods and short start-to-completion times are required. Applications cover transonic wing design/optimization, wing mounted stores load prediction, transonic buffet alleviation, fuselage loads estimation, and compact offset diffuser design for advanced aircraft configurations. Computational methods employed include extended transonic small disturbance (automatic grid embedding) formulation for analysis/design/optimization and a thin layer Navier-Stokes formulation for both external and internal flow analyses.
An implicit upwind scheme for the compressible Navier-Stokes equations is described and applied to the internal flow in a dual-throat nozzle. The method is second-order accurate spatially and naturally dissipative. A spatially-split approximate factorization method is used to obtain efficient steady-state solutions on the NASA Langley VPS-32 (CYBER 205) supercomputer.