Search NASA⌕ Search

SEARCH · Search NASA

Results for “MASS SPECTRA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Intact mass spectrometry screening to optimize hydroxyl radical dose for protein footprinting

Hydroxyl radical protein footprinting (HRPF) using synchrotron radiation is a well-validated method to assess protein structure in the native solution state. In this method, X-ray radiolysis of water generates hydroxyl radicals that can react with solvent accessible side chains of proteins, with mass spectrometry used to detect the resulting labeled products. An ideal footprinting dose provides sufficient labeling to measure the structure but not so much as to influence the results. The optimization of hydroxyl radical dose is typically performed using an indirect Alexa488 fluorescence assay sensitive to hydroxyl radical concentration, but full evaluation of the experiment's outcome relies upon bottom-up liquid chromatography mass spectrometry (LC-MS) measurements to directly determine sites and extent of oxidative labeling at the peptide and protein level. A direct evaluation of the extent of labeling to provide direct and absolute measurements of dose and “safe” dose ranges in terms of, for example, average numbers of labels per protein, would provide immediate feedback on experimental outcomes prior to embarking on detailed LC-MS analyses. To this end, we describe an approach to integrate intact MS screening of labeled samples immediately following exposure, along with metrics to quantify the extent of observed labeling from the intact mass spectra. Intact MS results on the model protein lysozyme were evaluated in the context of Alexa488 assay results and a bottom-up LC-MS analysis of the same samples. In conclusion, this approach provides a basis for placing delivered hydroxyl radical dose metrics on firmer technical grounds for synchrotron X-ray footprinting of proteins, with explicit parameters to increase the likelihood of a productive experimental outcome. Further, the method directs approaches to provide absolute and direct dosimetry for all types of labeling for protein footprinting.

59 BASIC BIOLOGICAL SCIENCES↗

Modeling and experiments on diffusion and activation of phosphorus in germanium

We report on phosphorus diffusion and activation related phenomena in germanium. We have used both conventional thermal processing and laser annealing by pulsed nanosecond Nd:YAG laser. Chemical profiles were obtained by secondary-ion-mass spectroscopy, sheet resistance was estimated by the van der Pauw method, and structural defects were monitored by transmission electron microscopy. Our study covers the temperature range from 440 to 750 deg. C, and we were able to efficiently simulate the dopant profiles within that temperature range, taking into account a quadratic dependence of the P diffusion coefficient on the free electron concentration. To achieve that we have taken into account dopant activation dependence on temperature as well as dopant pile-up near the surface and dopant loss owing to outdiffusion during the annealing. A combined laser thermal treatment above the melting threshold prior to conventional annealing allowed the elimination of the implantation damage, so we could perceive the influence of defects on both transient dopant diffusion and outdiffusion.

36 MATERIALS SCIENCE↗

Atom probe microscopy of three-dimensional distribution of silicon isotopes in {sup 28}Si/{sup 30}Si isotope superlattices with sub-nanometer spatial resolution

Laser-assisted atom probe microscopy of 2 nm period {sup 28}Si/{sup 30}Si isotope superlattices (SLs) is reported. Three-dimensional distributions of {sup 28}Si and {sup 30}Si stable isotopes are obtained with sub-nanometer spatial resolution. The depth resolution of the present atom probe analysis is much higher than that of secondary ion mass spectrometry (SIMS) even when SIMS is performed with a great care to reduce the artifact due to atomic mixing. Outlook of Si isotope SLs as ideal depth scales for SIMS and three-dimensional position standards for atom probe microscopy is discussed.

36 MATERIALS SCIENCE↗

Microstructure evolution in carbon-ion implanted sapphire

Carbon ions of MeV energy were implanted into sapphire to fluences of 1x10{sup 17} or 2x10{sup 17} cm{sup -2} and thermally annealed in forming gas (4% H in Ar) for 1 h. Secondary ion mass spectroscopy results obtained from the lower dose implant showed retention of implanted carbon and accumulation of H near the end of range in the C implanted and annealed sample. Three distinct regions were identified by transmission electron microscopy of the implanted region in the higher dose implant. First, in the near surface region, was a low damage region (L{sub 1}) composed of crystalline sapphire and a high density of plateletlike defects. Underneath this was a thin, highly damaged and amorphized region (L{sub 2}) near the end of range in which a mixture of i-carbon and nanodiamond phases are present. Finally, there was a pristine, undamaged sapphire region (L{sub 3}) beyond the end of range. In the annealed sample some evidence of the presence of diamond nanoclusters was found deep within the implanted layer near the projected range of the C ions. These results are compared with our previous work on carbon implanted quartz in which nanodiamond phases were formed only a few tens of nanometers from the surface, a considerable distance from the projected range of the ions, suggesting that significant out diffusion of the implanted carbon had occurred.

36 MATERIALS SCIENCE↗

Suppression of donor-vacancy clusters in germanium by concurrent annealing and irradiation

Diffusion of phosphorous and arsenic in germanium under in situ proton irradiation has been performed and analyzed with secondary ion mass spectrometry. Dopant profiles corresponding to proton-exposed regions exhibit a higher penetration depth and more pronounced box shape than profiles of nonexposed regions. Continuum theoretical simulations reveal that diffusion under irradiation is much less affected by inactive donor-vacancy clusters than diffusion under annealing only. The suppression of donor-vacancy clusters is caused by interstitials in supersaturation and vacancy concentrations close to thermal equilibrium. Concurrent annealing and irradiation have the potential to attain high active doping levels in Ge.

36 MATERIALS SCIENCE↗

Molecular beam deposition of Al{sub 2}O{sub 3} on p-Ge(001)/Ge{sub 0.95}Sn{sub 0.05} heterostructure and impact of a Ge-cap interfacial layer

We investigated the molecular beam deposition of Al{sub 2}O{sub 3} on Ge{sub 0.95}Sn{sub 0.05} surface with and without an ultra thin Ge cap layer in between. We first studied the atomic configuration of both Ge{sub 1-x}Sn{sub x} and Ge/Ge{sub 1-x}Sn{sub x} surfaces after deoxidation by reflection high-energy electron diffraction and resulted, respectively, in a c(4x2) and (2x1) surface reconstructions. After in situ deposition of an Al{sub 2}O{sub 3} high-{kappa} gate dielectric we evidenced using time-of-flight secondary ion mass spectroscopy analyses that Sn diffusion was at the origin of high leakage current densities in the Ge{sub 1-x}Sn{sub x}/Al{sub 2}O{sub 3} gate stack. This damage could be avoided by inserting a thin 5-nm-thick Ge cap between the oxide and the Ge{sub 1-x}Sn{sub x} layer. Finally, metal-oxide-semiconductor capacitors on the Ge capped sample showed well-behaved capacitance-voltage (C-V) characteristics with interface trap density (D{sub it}) in the range of 10{sup 12} eV{sup -1} cm{sup -2} in mid gap and higher close to the valence band edge.

36 MATERIALS SCIENCE↗

Driving vertical phase separation in a bulk-heterojunction by inserting a poly(3-hexylthiophene) layer for highly efficient organic solar cells

A desirable vertical phase separation of a bulk-heterojunction was achieved by inserting a P3HT layer between the blend layer and the poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) layer. According to the high (PEDOT:PSS) and low (P3HT) surface energies of substrate, it might be possible to modulate the vertical phase separation in the bulk-heterojunction. The result of vertical phase separation was determined using time-of-flight secondary-ion mass spectroscopy analysis. A controlled thickness of 50 nm for the inserted P3HT layer prevented undesirable light absorption and the power conversion efficiency of this condition was increased by 44% compared to that of a reference device.

36 MATERIALS SCIENCE↗

Combined Chemical and Topographic Imaging at Atmospheric Pressure via Microprobe Laser Desorption/Ionization Mass Spectrometry-Atomic Force Microscopy

The operational characteristics and imaging performance are described for a new instrument comprising an atomic force microscope (AFM) coupled with a pulsed laser and a linear ion trap mass spectrometer. The AFM operating mode is used to produce topographic surface images having nanometer-scale spatial and height resolution. Spatially resolved mass spectra of ions, produced from the same surface via microprobe-mode laser desorption/ionization at atmospheric pressure, are then used to create a 100 x 100 m chemical image. The effective spatial resolution of the image (~2 m) was constrained by the limit of detection (estimated to be 109 1010 ions) rather than by the diameter of the focused laser spot or the step size of the AFM sample stage. Thus, it is expected that improvements in imaging performance can be realized by implementation of post-ionization methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identification of peptide-binding sites within BSA using rapid, laser-induced covalent cross-linking combined with high-performance mass spectrometry

In this paper, we are developing a rapid, time-resolved method using laser-activated cross-linking to capture protein-peptide interactions as a means to interrogate the interaction of serum proteins as delivery systems for peptides and other molecules. A model system was established to investigate the interactions between bovine serum albumin (BSA) and 2 peptides, the tridecapeptide budding-yeast mating pheromone (α-factor) and the decapeptide human gonadotropin-releasing hormone (GnRH). Cross-linking of α-factor, using a biotinylated, photoactivatable p-benzoyl-L-phenylalanine (Bpa)–modified analog, was energy-dependent and achieved within seconds of laser irradiation. Protein blotting with an avidin probe was used to detect biotinylated species in the BSA-peptide complex. The cross-linked complex was trypsinized and then interrogated with nano-LC–MS/MS to identify the peptide cross-links. Cross-linking was greatly facilitated by Bpa in the peptide, but some cross-linking occurred at higher laser powers and high concentrations of a non-Bpa–modified α-factor. This was supported by experiments using GnRH, a peptide with sequence homology to α-factor, which was likewise found to be cross-linked to BSA by laser irradiation. Analysis of peptides in the mass spectra showed that the binding site for both α-factor and GnRH was in the BSA pocket defined previously as the site for fatty acid binding. This model system validates the use of laser-activation to facilitate cross-linking of Bpa-containing molecules to proteins. Finally, the rapid cross-linking procedure and high performance of MS/MS to identify cross-links provides a method to interrogate protein-peptide interactions in a living cell in a time-resolved manner.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved interfacial state density in Al{sub 2}O{sub 3}/GaAs interfaces using metal-organic chemical vapor deposition

In situ deposition of Al{sub 2}O{sub 3} on GaAs was performed by chemical-vapor-deposition (CVD) with trimethyaluminum and isopropanol as precursors. A gallium-rich region in the Al{sub 2}O{sub 3} thin film above the interface was spontaneously formed via the in situ CVD process. Ga-enrichment of the interface was observed using secondary ion mass spectrometry (SIMS) depth profile measurement. X-ray photoelectron spectroscopy (XPS) results show that the gallium-rich region consists of Al{sub 2}O{sub 3} and Ga{sub 2}O{sub 3}, but no As{sub 2}O{sub 3} was observed. The Ga{sub 2}O{sub 3}-Al{sub 2}O{sub 3} layer above the oxide/GaAs interface reduces the frequency dispersion as measured with capacitance-voltage (C-V) characteristics and lowers the interfacial state density as compared to atomic-layer-deposition *(ALD) deposited films which do not display this gallium enrichment above the interface.

36 MATERIALS SCIENCE↗

Results from the Gas Chromatograph Mass Spectrometer (GCMS) Experiment on the Cassini-Huygens Probe

The Gas Chromatograph Mass Spectrometer was one of six instruments on the Cassini-Huygens Probe mission to Titan. The GCMS measured in situ the chemical composition of the atmosphere during the probe descent and served as the detector for the pyrolization products for the Aerosol Collector Pyrolyser (ACP) experiment to determine the composition of the aerosol particles. The GCMS collected data from an altitude of 146 km to ground impact. The Probe and the GCMS survived impact and collected data for 1 hour and 9 minutes on the surface. Mass spectra were collected during descent and on the ground over a range of m/z from 2 to 141. The major constituents of the lower atmosphere were confirmed to be N2 and CH4. The methane mole fraction was uniform in the stratosphere. It increased below the tropopause, at about 32 km altitude, monotonically toward the surface, reaching a plateau at about 8 km at a level near saturation. After surface impact a steep increase of the methane signal was observed, suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. The measured mole fraction of Ar-40 is 4.3x10(exp -5) and of Ar-36 is 2.8x10(exp -7). The other primordial noble gases were below 10(exp -8) mole fraction. The isotope ratios of C-12/C-13 determined from methane measurements are 82.3 and of N-14/N-15 determined from molecular nitrogen are 183. The D/H isotope ratio determined from the H2 and HD measurements is 2.3x10(exp -4). Carbon dioxide, methane, acetylene and cyanogen were detected evaporating from the surface in addition to methane. The GCMS employed a quadrupole mass filter with a secondary electron multiplier detection system and a gas sampling system providing continuous direct atmospheric composition measurements and batch sampling through three gas chromatographic (GC) columns, a chemical scrubber and a hydrocarbon enrichment cell. The GCMS gas inlet was heated to prevent condensation, and to evaporate volatiles from the surface after impact.

Niemann, H.↗

Results from the Gas Chromatograph Mass Spectrometer (GCMS) Experiment on the Cassini-Huygens Probe

The Gas Chromatograph Mass Spectrometer was one of six instruments on the Cassini-Huygens Probe mission to Titan. The GCMS measured in situ the chemical composition of the atmosphere during the probe descent and served as the detector for the pyrolization products for the Aerosol Collector Pyrolyser (ACP) experiment to determine the composition of the aerosol particles. The GCMS collected data from an altitude of 146 km to ground impact. The Probe and the GCMS survived impact and collected data for 1 hour and 9 minutes on the surface. Mass spectra were collected during descent and on the ground over a range of mlz from 2 to 141. The major constituents of the lower atmosphere were confirmed to be N2 and CH4. The methane mole fraction was uniform in the stratosphere. It increased below the tropopause, at about 32 km altitude, monotonically toward the surface, reaching a plateau at about 8 km at a level near saturation. After surface impact a steep increase of the methane signal was observed, suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. The measured mole fraction of Ar-40 is 4.3x10(exp -5) and of Ar-36 is 2.8x10(exp -7). The other primordial noble gases were below 10(exp -8) mole fraction. The isotope ratios of C-12/C-13 determined from methane measurements are 82.3 and of N-14/N-15 determined from molecular nitrogen are 183. The D/H isotope ratio determined from the H2 and HD measurements is 2.3x10(exp -4). Carbon dioxide, ethane, acetylene and cyanogen were detected evaporating from the surface in addition to methane. The GCMS employed a quadrupole mass filter with a secondary electron multiplier detection system and a gas sampling system providing continuous direct atmospheric composition measurements and batch sampling through three gas chromatographic (GC) columns, a chemical scrubber and a hydrocarbon enrichment cell. The GCMS gas inlet was heated to prevent condensation, and to evaporate volatiles from the surface after impact.

Niemann, Hasso↗

Isotopic tracing study of the growth of silicon carbide nanocrystals at the SiO{sub 2}/Si interface by CO annealing

The epitaxial growth of beta-Sic nanocrystals at the Si{sup 16}O{sub 2}/Si(100) interface under CO annealing has been studied using {sup 13}C{sup 18}O and isotopically sensitive nuclear reaction analysis and secondary ion mass spectrometry analysis. The results show that the amount of SiC increases linearly with the CO pressure and the annealing time. We demonstrate that the CO diffuses as a molecule in the silica and that for each C atom reacting to form SiC, an oxygen atom is incorporated in the vicinity of the interface. The linear and the parabolic rate constants corresponding to an adapted Deal and Grove model are also determined.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Electron transport properties of antimony doped SnO{sub 2} single crystalline thin films grown by plasma-assisted molecular beam epitaxy

By antimony doping tin oxide, SnO{sub 2}:Sb (ATO), below 1.0% Sb concentration, controllable n-type doping was realized. Plasma-assisted molecular beam epitaxy has been used to grow high quality single crystalline epitaxial thin films of unintentionally doped (UID) and Sb-doped SnO{sub 2} on r-plane sapphire substrates. A UID thickness series showed an electron concentration of 7.9x10{sup 18} cm{sup -3} for a 26 nm film, which decreased to 2.7x10{sup 17} cm{sup -3} for a 1570 nm film, whereas the mobility increased from 15 to 103 cm{sup 2}/V s, respectively. This series illustrated the importance of a buffer layer to separate unintentional heterointerface effects from the effect of low Sb doping. Unambiguous bulk electron doping was established by keeping the Sb concentration constant but changing the Sb-doped layer thickness. A separate doping series correlated Sb concentration and bulk electron doping. Films containing between 9.8x10{sup 17} and 2.8x10{sup 20} Sb atoms/cm{sup 3} generated an electron concentration of 1.1x10{sup 18}-2.6x10{sup 20} cm{sup -3}. As the atomic Sb concentration increased, the mobility and resistivity decreased from 110 to 36 cm{sup 2}/V s and 5.1x10{sup -2} to 6.7x10{sup -4} OMEGA cm, respectively. The Sb concentration was determined by secondary ion mass spectrometry. X-ray diffraction and atomic force microscopy measurements showed no detrimental effects arising from the highest levels of Sb incorporation. Temperature dependent Hall measurements established a lower limit for the Sb electron activation energy of 13.2 meV and found that films with greater than 4.9x10{sup 19} electrons/cm{sup 3} were degenerately doped. Within experimental uncertainties, 100% donor efficiency was determined for Sb-doped SnO{sub 2} in the range studied.

36 MATERIALS SCIENCE↗

Hydrogen refinement during solid phase epitaxy of buried amorphous silicon layers

The effect of hydrogen on the kinetics of solid phase epitaxy (SPE) have been studied in buried amorphous Si layers. The crystallization rate of the front amorphous/crystalline (a/c) interface is monitored with time resolved reflectivity. Secondary ion mass spectrometry (SIMS) is used to examine H implanted profiles at selected stages of the anneals. The H retardation of the SPE rate is determined up to a H concentration of 2.3x10{sup 20} cm{sup -3} where the SPE rate decreases by 80%. Numerical simulations are performed to model the H diffusion, the moving a/c interfaces and the refinement of the H profile at these interfaces. Despite the high H concentration involved, a simple Fickian diffusion model results in good agreement with the SIMS data. The segregation coefficient is estimated to be 0.07 at 575 deg. C. A significant fraction of the H escapes from the a-Si layer during SPE especially once the two a/c interfaces meet which is signified by the lack of H-related voids after a subsequent high temperature anneal.

36 MATERIALS SCIENCE↗

Optical and mass-spectral characterization of mixed-gas flowing atmospheric-pressure afterglow sources

Plasma-based ambient desorption/ionization (ADI) sources for mass spectrometry (MS) often use helium as the primary discharge gas due to the large reaction cross section of excited helium species with atmospheric gases, which ultimately leads to efficient reagent-ion formation. However, some studies have shown that mixed-gas plasmas provide unique advantages. For instance, our group showed that a helium-oxygen flowing atmospheric-pressure afterglow (He:O 2 -FAPA) source yielded enhanced ion signals for small polar analytes, but compounds with aromatic rings underwent chemical modification to produce pyrylium species. Here, it is shown that the addition of H 2 to the helium FAPA gas significantly decreased the reagent-ion signals, but analyte-ion signal was not affected to the same degree. In addition, mass spectra obtained with He:H 2 -FAPA were chemically cleaner with fewer ions stemming from analyte species and produced less oxidation of analytes. Addition of nitrogen increased the abundance of negative reagent ions (e.g., NO 2 - and NO 3 - ) which led to enhanced ion signal for RDX. To better understand these unique advantages of a mixed-gas FAPA, the impact of molecular-gas (O 2 , N 2 , or H 2 ) addition on the optical-emission spectra from the discharge was also measured. Spatially resolved emission was obtained from the anode- and negative-glow regions. In general, addition of small fractions (~0.1%) of molecular gases decreased helium and OH emission intensities. Atomic oxygen and hydrogen emission increased with the addition of O 2 and H 2 , respectively. Furthermore, emission characteristics of N 2 , N 2 + , and NO with respect to molecular gas composition on He-FAPA were measured. Finally, fundamental plasma parameters, such as OH rotational temperature (T rot ), were also calculated for these mixed-gas systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface segregation effects of erbium in GaAs growth and their implications for optical devices containing ErAs nanostructures

We report on the integration of semimetallic ErAs nanoparticles with high optical quality GaAs-based semiconductors, grown by molecular beam epitaxy. Secondary ion mass spectrometry and photoluminescence measurements provide evidence of surface segregation and incorporation of erbium into layers grown with the erbium cell hot, despite the closed erbium source shutter. We establish the existence of a critical areal density of the surface erbium layer, below which the formation of ErAs precipitates is suppressed. Based upon these findings, we demonstrate a method for overgrowing ErAs nanoparticles with III-V layers of high optical quality, using subsurface ErAs nanoparticles as a sink to deplete the surface erbium concentration. This approach provides a path toward realizing optical devices based on plasmonic effects in an epitaxially-compatible semimetal/semiconductor system.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The use of gas chromatography – high resolution mass spectrometry for suspect screening and non-targeted analysis of per- and polyfluoroalkyl substances

This study is a workflow development for the analysis, identification, and categorization of per- and polyfluoroalkyl substances (PFAS) using gas chromatography-high resolution mass spectrometry (GC-HRMS) with non-targeted analysis (NTA) and suspect screening techniques. The behavior of various PFAS in a GC-HRMS was studied with regards to retention indices, ionization susceptibility, fragmentation patterns, etc. A custom PFAS database was constructed from 141 diverse PFAS. The database contains mass spectra from electron ionization (EI) mode, as well as MS and MS/MS spectra from positive and negative chemical ionization (PCI and NCI, respectively) modes. Common fragments of PFAS were identified across a diverse set of 141 PFAS analyzed. A workflow for suspect screening of PFAS and partially fluorinated products of incomplete combustion/destruction (PICs/PIDs) was developed which utilized both the custom PFAS database and external databases. PFAS and other fluorinated compounds were identified in both a challenge sample (designed to test the identification workflow) and incineration samples suspected to contain PFAS and fluorinated PICs/PIDs. The challenge sample resulted in a 100% true positive rate (TPR) for PFAS which were present in the custom PFAS database. In conclusion, several fluorinated species were tentatively identified in the incineration samples using the developed workflow.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗