Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mechanical testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Pultrusion Process Development for Long Space Boom Model

Long flexible-boom models were required to develop ground-vibration test methods for very-low-frequency space structures with applications to the proposed Space Station. Pultruded quasi-isotropic composite beams were selected as an option over extruded aluminum alloy structures because of the lower cost potential, the higher specific strength, the flexural properties, and the dynamic similarity considerations. The reinforcement material that was used was biaxial (0 deg/90 deg) fiberglass roving held in place with knitted polyester yarn such that equal fiber volume in 0 deg and 90 deg orientations provided nearly equal strength in both longitudinal and transverse directions. An isophthalic polyester resin system was used as the matrix. Continuous lengths up to 270 ft were easily pultruded with biaxial fabric. Tracking problems were encountered with similar unidirectional fabrics. Analyses of processing problems were conducted to determine causes for delamination, scaling, and sloughing. Ultrasonic C-scanning and scanning electron microscope examinations were conducted as well as mechanical testing to failure. Test results indicate that pultrusion processes can be used to produce quasi-isotropic composite structures.

Wilson, Maywood L.↗
DOE OSTI2022

High-temperature deformation mechanisms in a BCC+B2 refractory complex concentrated alloy

The current study reports the analysis of the deformation mechanisms at 600 °C in a two-phase, BCC+B2, refractory complex concentrated alloy (RCCA) Al 0.5 NbTa 0.8 Ti 1.5 V 0.2 Zr. At this temperature, the alloy microstructure is unstable and dynamic coarsening of B2 precipitates is evidenced during the mechanical testing. After true plastic strain of 0.030 at strain rate of 10 -4 s -1 , the deformation becomes highly localized in wavy bands reflecting the profusion of cross-slip. Scanning transmission electron microscopy (STEM) observations highlight the presence of paired a/2$\langle$111$\rangle$ dislocations that shear the B2 precipitates in a cooperative process. Additionally, some chemical segregation effect is observed along the narrow dislocation bands likely induced to decrease the antiphase boundary (APB) energy of the system.

ordering↗
DOE OSTI2023

Overview of a Versatile Loading System for Anisotropic Material Property Characterization

Additive manufacturing, cold rolling, and other thermomechanical treatments on metals, especially HCP, can cause texture and oriented grain structures resulting in anisotropic mechanical properties. This can lead to macroscopic response that significantly deviates from isotropic assumptions which motivates studying mechanical properties in multiple directions. In addition, multiaxial loading and complex stress states overlapping the above mentioned material anisotropy can lead to unexpected outcomes. Idaho National Laboratory developed an advanced mechanical testing system to study a range of uniaxial to multiaxial stress states while measuring the anisotropic response bringing insight into the overlap between material properties and stress states. High-temperature capability and stress- or strain-controlled loading is available to enable a variety of experiment types and conditions to measure elastic, plastic, and viscoplastic properties. This poster presents the design and capabilities of this system with preliminary results highlighting the benefits of multiaxial loading and anisotropic analysis in an integrated system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Computational discovery of ultra-strong, stable, and lightweight refractory multi-principal element alloys. Part II: comprehensive ternary design and validation

Abstract Here the discovery of refractory multi-principal element alloys (MPEAs) with high-temperature strength and stability is pursued within a constrained and application-relevant design space. A comprehensive approach is developed and applied to explore all 165 ternary systems in the Al-Ce-Fe-Hf-Mo-Nb-Ta-Ti-V-W-Zr family. A subset of ternary systems that contain large areas in composition–temperature space with high strength and robust BCC phase stability is found. Twelve sets of high-performing alloys are identified, each set optimized for one combination of phase constraint, optimization target, and temperature range. Preliminary mechanical tests support the viability of the method. This work highlights the importance of considering phase stability, exploring non-equiatomic regions of composition space, and applying application-relevant constraints. Parts I and II provide three down-selection techniques for identifying high-performing BCC refractory MPEAs, design guidelines, and many candidates predicted to have BCC phase stability and strengths 2–3 times higher than any reported to date.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dataset of tensile properties for sub-sized specimens of nuclear structural materials

Mechanical testing with sub-sized specimens plays an important role in the nuclear industry, facilitating tests in confined experimental spaces with lower irradiation levels and accelerating the qualification of new materials. The reduced size of specimens results in different material behavior at the microscale, mesoscale, and macroscale, in comparison to standard-sized specimens, which is referred to as the “specimen size effect.” Although analytical models have been proposed to correlate the properties of sub-sized specimens to standard-sized specimens, these models lack broad applicability across different materials and testing conditions. The objective of this study is to create the first large public dataset of tensile properties for sub-sized specimens used in nuclear structural materials. We performed an extensive literature review of relevant publications and extracted over 1,000 tensile testing records comprising 55 columns including material type and composition, manufacturing information, irradiation conditions, specimen dimensions, and tensile properties. The dataset can serve as a valuable resource to investigate the specimen size effect and develop computational methods to correlate the tensile properties of sub-sized specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhanced biomechanical performance of additively manufactured Ti-6Al-4V bone plates

As the global trauma fixation devices market expands rapidly, it is imperative to improve the production of fixation devices through enhanced design accuracy and fit for best performance and maximum patient comfort. Selective laser melting (SLM) is one of the mature additive manufacturing methods, which provides a viable route for the rapid production of such devices. In this work, the ability of SLM to produce near-net-shape parts, as desired for medical implants, was utilized for the fabrication of bone plates from Ti-6Al-4V alloy powder. Martensitic microstructure obtained after the printing of alloy resulted in poor ductility, limiting its application in the field of orthopedics. A specially designed repeated cyclic heating and cooling close to but below the β-transus was used to transform from acicular to a bimodal microstructure without the need for plastic deformation prior to heat treatment for improving the ductility. Bone plates subjected to this heat treatment were mechanically tested by means of tensile and 3-point bend tests and demonstrated large improvement in ductility, and the values were comparable to those similar plates prepared from wrought alloy. Other important properties required for implants were assessed, such as corrosion resistance in simulated body fluid and cytocompatibility in vitro using MC3T3-E1 cells. These results for the bone plate after heat treatment were excellent and similar to those of the additively manufactured and wrought plates. Taken together, the performance of the additively manufactured bone plates after subjecting to heat treatment was similar to those of bone plate manufactured using wrought alloy. These results have important implications for the fabrication of patient-specific metallic orthopedic devices using SLM without compromising their biomechanical performance by subjecting them to a tailored heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Advancing the mechanical integrity and fragmentation behavior of reactive projectiles

A multivariant statistical approach was used to identify treatment conditions that improve the survivability of structural reactive material (SRM) projectiles upon launch and enhance energy release upon impact. The study included both mechanical testing of projectiles as well as their reactive characterization. The projectiles were launched in a high-velocity impact-ignition testing system and impacted an anvil for vented chamber calorimetry. This study examined a link between ultimate compressive stress and combustion performance. Two treatments were applied to consolidated aluminum projectiles including annealing and addition of silica (SiO 2 ) inclusions. Results showed annealing at moderate temperatures resulted in intact SRM projectiles upon launch. Adding small concentrations (1–2 wt. %) of SiO 2 to the SRM promoted fragmentation and combustion performance upon impact. Compared to the untreated projectiles, annealing with SiO 2 inclusion processing treatments improved the energy conversion efficiency from 37–84% (for untreated projectiles) up to 54–98%. In conclusion, increasing interparticle dislocation recovery by annealing while balancing inclusions promoting fragmentation upon impact was the key to optimizing combustion performance for SRM ballistic impact applications.

42 ENGINEERING↗
DOE OSTI2022

Electric current-induced precipitation hardening in advanced high-strength steel

Effect of electric current on precipitation hardening for advanced high-strength steel is investigated based on mechanical testing and microscopic observation. Complex-phase steel containing nano-sized Nb-bearing carbides was used. By comparing the flow stress between uniaxial tension with applied electric current (pulsed tension) and without electric current (nonpulsed tension) at various elevated temperatures, the influence of electric current on precipitation hardening was confirmed. A higher values of Vickers hardness and full-width-at-half-maximum were obtained in the pulsed tensile specimen compared to the identically heat treated specimen after the same deformation. Small angle neutron scattering analysis showed that the volume fraction and mean diameter of newly formed precipitates in the pulsed tensile specimen were higher and larger than those in the induction heat treated specimen, respectively. In conclusion, it clearly shows that additional precipitation hardening could be induced by the athermal effect of electric current, which is distinct from the thermal effect of Joule heating.

36 MATERIALS SCIENCE↗
NASA NTRS2009

A Biomechanical Approach to Assessing Hip Fracture Risk

Bone loss in microgravity is well documented, but it is difficult to quantify how declines in bone mineral density (BMD) contribute to an astronaut's overall risk of fracture upon return. This study uses a biomechanical approach to assessing hip fracture risk, or Factor of Risk (Phi), which is defined as the ratio of applied load to bone strength. All long-duration NASA astronauts from Expeditions 1-18 were included in this study (n=25), while crewmembers who flew twice (n=2) were treated as separate subjects. Bone strength was estimated based on an empirical relationship between areal BMD at the hip, as measured by DXA, and failure load, as determined by mechanical testing of cadaver femora. Fall load during a sideways fall was calculated from a previously developed biomechanical model, which takes into account body weight, height, gender, and soft tissue thickness overlying the lateral aspect of the hip that serves to attenuate the impact force. While no statistical analyses have been performed yet, preliminary results show that males in this population have a higher FOR than females, with a post- flight Phi of 0.87 and 0.36, respectively. FOR increases 5.1% from preflight to postflight, while only one subject crossed the fracture "threshold" of Phi = 1, for a total of 2 subjects with a postflight Phi > 1. These results suggest that men may be at greater risk for hip fracture due largely in part to their relatively thin soft tissue padding as compared to women, since soft tissue thickness has the highest correlation (R(exp 2)= .53) with FOR of all subject-specific parameters. Future work will investigate changes in FOR during recovery to see if baseline risk levels are restored upon return to 1-g activity. While dual x-ray absorptiometry (DXA) is the most commonly used clinical measure of bone health, it fails to provide compartment-specific information that is useful in assessing changes to bone quality as a result of microgravity exposure. Peripheral quantitative computed tomography (pQCT) accomplishes this by imaging transverse "slices" of the long bones. This project was a re-analysis of a 90 day bed rest study to determine if changes to cortical and trabecular compartments could be detected in the distal tibia with statistical significance using a new pQCT image analysis method. Nearly all changes in bone mineral density (BMD) and cross sectional area (CSA) measures were seen with statistical significance, with the exception of a change in cortical BMD. Total bone CSA increased by 1.1 % (p =0.01), cortical CSA decreased by - 5.6% (p<0.001) and trabecular CSA increased by 1.76% (p=0.007); the combination of which suggests bone resorption occurred at the endocortical surface in response to mechanical unloading by bed rest. Furthermore, total BMD and trabecular BMD decreased (-3.8%, p=0.001 and -2.8%, p =0.007, respectively), while decreases in cortical BMD failed to reach significance (-1.2%, p=0.07). Given that compartment-specific changes are seen with significance and are likely to influence bone strength, it is recommended that pQCT remain a standard measure used in bed rest because it provides a unique measure by which to better evaluate the efficacy of countermeasures to microgravity-induced bone loss.

Ellman, Rachel↗
DOE OSTI2025

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗
DOE OSTI2023

Infusible Thermoplastic Composites for Wind Turbine Blade Manufacturing: Fatigue Life of Thermoplastic Laminates under Ambient and Low-Temperature Conditions

Traditionally, thermoset resins such as polyesters (PE) and epoxies are used as the polymer matrix for construction of wind turbine blades. However, concern about their end-of-life treatment garners interest to use thermoplastics for increased recyclability. However, the high viscosity of molten thermoplastics inhibits their use in manufacturing wind turbine blades with injection or compression molding. A recently developed, infusible, reactive thermoplastic resin overcomes this technological barrier. Toward verifying that this recyclable resin is suitable for use in wind turbine blades, a dataset of R?=?0.1 and R?=?10 fatigue data for glass fiber-reinforced acrylic composites is provided and equal fatigue life to industry standard epoxy and unsaturated PE resin systems is demonstrated. Specifically, R?=?0.1 fatigue data for acrylic composites at room temperature and -30?degrees C for verification of low-temperature performance are tabulated. To elucidate failure mechanisms, in situ mechanical testing with X-ray computed tomography demonstrates that damage accumulation occurs by crack propagation along the fiber-matrix interface under cyclic loading. Infrared (IR) thermography predicts failure points in composites specimens with porosity defects introduced from nonideal manufacturing processes. Furthermore, these manufacturing defects are shown to compromise the fatigue life of the acrylic laminates by an order of magnitude.

effect of defects↗
DOE OSTI2024

Tuning Microstructure of Mesophase Pitch Carbon Fiber by Altering the Carbonization Ramp Rate

The microstructure of mesophase pitch carbon fibers (CFs) are tuned by varying ramp rates from 1 to 50 °C min –1 up to 1000 °C to study the effect of ramp rate on CFs’ microstructure, thermal and mechanical properties with the goal of offsetting the cost by decreasing cycle time. The ramp rates represent carbonization times ranging from 16.4 to 1.17 h, not including cool down. Differential scanning calorimetry, thermogravimetric analysis, and derivative thermogravimetry are used to investigate the impact ramp rate has on the thermal properties of mesophase pitch. It is found that lower ramp rates are endothermic in nature with a lower temperature onset and maximum weight loss. Higher ramp rates possess an exothermic nature with higher temperatures resulting in maximal weight loss over a smaller range of temperatures. Mechanical testing shows varying CF strengths and moduli dependent on ramp rate and an optimized process is developed to produce the strongest CF. Furthermore, microstructural characterization revealed that faster ramp rates lead to smaller interplanar spacings and larger crystallites but possessed greater disorder.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Limitations of Hydrogen Detection After 150 Years of Research on Hydrogen Embrittlement

Hydrogen's significance in contemporary society lies in its remarkable energy density, yet its integration into the worldwide energy grid presents a substantial challenge. Exposing materials to hydrogen environments leads to degradation of mechanical properties, damage, and failure. While the current approach for assessing hydrogen's impact on materials involves mainly multiscale modeling and mechanical testing, there exists a significant deficiency in detecting the intricate interactions between hydrogen and materials at the nanoatomic scales and under in situ conditions. This perspective review highlights the experimental endeavors aimed at bridging this gap, pointing toward the imminent need for new experimental techniques that can detect and map hydrogen in materials’ microstructures and their site‐specific dependencies.

Tunes, Matheus A.↗
DOE OSTI2023

Structure, Function, and Application of Self–Healing Adhesives from Mistletoe Viscin

Berries from the European Mistletoe (Viscum album) possess a sticky tissue called viscin that facilitates adhesion and germination onto host trees. Recent studies of viscin have demonstrated its adhesive capacity on a range of natural and synthetic surfaces including wood, skin, metals, and plastic. Yet, the underlying mechanisms remain poorly understood. Here, an investigation of the adhesive performance of mistletoe viscin is performed, demonstrating its hygroscopic nature and ability to self-heal following adhesive failure. It is identified that adhesion originates from a water-soluble adhesive component that can be extracted, isolated, and characterized independently. Lap shear mechanical testing indicates that the mistletoe adhesive extract (MAE) outperforms native viscin tissue, as well as gum arabic and arabinogalactan—common plant-based adhesives. Furthermore, humidity uptake experiments reveal that MAE can reversibly absorb nearly 100% of its mass in water from the atmosphere. In-depth spectroscopic and mass spectrometry investigations reveal a composition consisting primarily of an atypical arabinogalactan, with additional sugar alcohols. Finally, several proof-of-concept applications are demonstrated using MAE for hygro-responsive reversible adhesion between various surfaces including skin, plastic, PDMS, and paper, revealing that MAE holds potential as a biorenewable and reusable adhesive for applications in cosmetics, packaging, and potentially, tissue engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Energy‐Water Asynchrony Principally Determines Water Available for Runoff From Snowmelt in Continental Montane Forests

ABSTRACT Changes in the volume, rate, and timing of the snowmelt water pulse have profound implications for seasonal soil moisture, evapotranspiration (ET), groundwater recharge, and downstream water availability, especially in the context of climate change. Here, we present an empirical analysis of water available for runoff using five eddy covariance towers located in continental montane forests across a regional gradient of snow depth, precipitation seasonality, and aridity. We specifically investigated how energy‐water asynchrony (i.e., snowmelt timing relative to atmospheric demand), surface water input intensity (rain and snowmelt), and observed winter ET (winter AET) impact multiple water balance metrics that determine water available for runoff (WAfR). Overall, we found that WAfR had the strongest relationship with energy‐water asynchrony (adjusted r 2 = 0.52) and that winter AET was correlated to total water year evapotranspiration but not to other water balance metrics. Stepwise regression analysis demonstrated that none of the tested mechanisms were strongly related to the Budyko‐type runoff anomaly (highest adjusted r 2 = 0.21). We, therefore, conclude that WAfR from continental montane forests is most sensitive to the degree of energy‐water asynchrony that occurs. The results of this empirical study identify the physical mechanisms driving variability of WAfR in continental montane forests and are thus broadly relevant to the hydrologic management and modelling communities.

Webb, Ryan William↗
DOE OSTI2020

Synchrotron CT imaging of lattice structures with engineered defects

Understanding mechanical failure, crack propagation, and compressive behavior at the micrometer scale is essential for tailoring material properties for structural performance in cellular materials. Typically, modeling of traditional polymer foam materials is clouded by the lack of control in material morphology and its inherent stochastic structure. Additive manufacturing with sub-micrometer resolution provides a direct path for experimenters to specifically tailor structures needed by modelers to explicitly probe mechanical performance. Using laboratory-based 3D X-ray computed tomographic imaging (CT), the examination of deformation and damage provides a critical path to understand how these soft materials behave. Additionally, synchrotron CT yields realistic information at higher strain rates to directly validate the robustness of our finite element modeling. For this study, nanolithographic printing was employed to generate a series of engineered lattices with increasing levels of defects through the random removal of ligaments. These structures were mechanically tested and imaged with laboratory-based microCT. Additionally, synchrotron experiments were conducted in which the structures were imaged in 3D at 14 Hz during compression at a 0.4 s –1 strain rate. These 3D images show the changes in the structure as the ligaments bend, buckle and fracture in real time. This technique provides a robust framework for developing our methodologies and future exploration of engineered structures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dissimilar Material Joining via Interlocking Metasurfaces

Background The integration of dissimilar materials poses a significant challenge in engineering, necessitating innovative solutions for robust and reliable joining. Interlocking metasurfaces (ILMs) are a new joining technology comprising arrays of autogenous features patterned across two surfaces that interlock to form robust structural joints. Objective Here, this study elucidates the factors influencing the tensile performance of ILM joints formed between dissimilar materials. Methods We employed parametric optimization to identify optimal unit cell geometries for maximal yield strength based on the hypothesis that the elastic tensile properties of the materials are the primary determinants of tensile performance. Experimental validation was performed by mechanically testing the theorized optimal ILM geometry and a range of ILM geometries to capture the overall behavior trends of joints between two additively manufactured polymers, VeroPureWhite (VW) and RGDA8430-DM (8430). Results Experimental validation of optimized designs revealed that additional factors, e.g. flexural strength and localized plasticity, also strongly influenced the tensile performance of T-slot ILMs joining dissimilar materials. The proposed optimal design remained the best performer. Conclusions This study demonstrates the viability of ILMs as a joining method for dissimilar materials. ILMs can join dissimilar materials with no loss in joint yield strength compared to joints composed solely of the weaker of the two constitutive materials. ILMs demonstrated their potential as a versatile and effective joining technology in diverse engineering applications.

Elbrecht, Benjamin James [Sandia National Laborato↗