Search NASA⌕ Search

SEARCH · Search NASA

Results for “PITCH CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Preliminary study of VTO thrust requirements for a V/STOL aircraft with lift plus lift/cruise propulsion

A preliminary assessment was made of the VTO thrust requirements for a supersonic (Type B) aircraft with a Lift plus Lift/Cruise propulsion system. A baseline aircraft with a takeoff gross weight (TOGW) of 13 608 kg (30,000 lb) was assumed. Pitch, roll, and yaw control thrusts (i.e., the thrusts needed for aircraft attitude control in the flight hover mode) were estimated based on a specified set of maneuver acceleration requirements for V/STOL aircraft. Other effects (such as installation losses, suckdown, reingestion, etc.), which add to the thrust requirements for VTO were also estimated. For the baseline aircraft, the excess thrust required for attitude control of the aircraft during VTO and flight hover was estimated to range from 36.9 to 50.9 percent of the TOGW. It was concluded that the total thrust requirements for the aircraft/propulsion system are large and significant. In order to achieve the performance expected of this aircraft/propulsion system, reductions must be made in the excess thrust requirements.

Turney, G. E.↗
NASA NTRS1980

QCSEE UTW engine powered-lift acoustic performance

Powered-lift acoustic test of the Quiet Clean Short Haul Experimental Engine (QCSEE) under the wing (UTW) engine are reported. Propulsion systems for two powered-lift concepts were designed, fabricated, and tested. In addition to low noise features, the designs included composite structures, gear-driven fans, digital control, and a variable pitch fan (UTW). The UTW engine was tested in a static ground test facility with wing and flap segments to simulate installation on a short haul transport aircraft of the future. Powered-lift acoustic performance of the UTW engine is compared with that of the previously tested and reported QCSEE over-the-wing (OTW) engine. Both engines were slightly above the noise goal but were significantly below current FAA and modern wide-body jet transport levels. The UTW system in the powered-lift mode was penalized by reflected engine noise from the wing and flap system, while the OTW system was benefitted by a wing noise shielding effect.

Loeffler, I. J.↗
NASA NTRS1981

Aerodynamic characteristics of a series of airbreathing missile configurations

The results of an experimental program conducted in order to compile a data base useful in the application of airbreathing propulsion to missiles are presented. The configurations investigated used two-dimensional or axisymmetric twin inlets located at three alternative circumferential positions: 90, 115 and 135 deg to the vertical centerline. The effects of a wing located above the inlets and of various tail configurations were investigated, with a view to longitudinal stability/control and lateral-directional stability characteristics. It is noted that of the three tail configurations tested, the 'X' tail showed (1) the most linear pitch-moment curve, (2) control effectiveness, and (3) positive lateral-directional stability.

Hayes, C.↗
NASA NTRS1982

Microprocessor control system for 200-kilowatt Mod-OA wind turbines

The microprocessor system and program used to control the operation of the 200-kW Mod-OA wind turbines is described. The system is programmed to begin startup and shutdown sequences automatically and to control yaw motion. Rotor speed and power output are controlled with integral and proportional control of the blade pitch angle. Included in the report are a description of the hardware and a discussion of the software programming technique. A listing of the PL/M software program is given.

Nyland, T. W.↗
NASA NTRS1982

Gust response of commercial jet aircraft including effects of autopilot operation

A simplified theory of aircraft vertical acceleration gust response based on a model including pitch, vertical displacement and control motions due to autopilot operation is presented. High-order autopilot transfer functions are utilized for improved accuracy in the determination of the overall response characteristics. Four representative commercial jet aircraft were studied over a wide range of operating conditions and comparisons of individual responses are given. It is shown that autopilot operation relative to the controls fixed case causes response attenuation of from 10 percent to approximately 25 percent depending on flight condition and increases in crossing number up to 30 percent, with variations between aircraft of from 5 percent to 10 percent, in general, reflecting the differences in autopilot design. A detailed computer program description and listing of the calculation procedure suitable for the general application of the theory to any airplane autopilot combination is also included.

Goldberg, J. H.↗
NASA NTRS1983

Body-surface pressure data on two monoplane-wing missile configurations with elliptical cross sections at Mach 2.50

Tabulated body surface pressure data for two monoplane-wing missile configurations are presented and analyzed. Body pressure data are presented for body-alone, body-tail, and body-wing-tail combinations. For the lost combination, data are presented for tail-fin deflection angles of 0 deg and 30 deg to simulate pitch, yaw, and roll control for both configurations. The data cover angles of attack from -5 deg to 25 deg and angles of roll from 0 deg to 90 deg at a Mach number of 2.50 and a Reynolds number of 6.56 x 1,000,000 per meter. Very consistent, systematic trends with angle of attack and angle of roll were observed in the data, and very good symmetry was found at a roll angle of 0 deg. Body pressures depended strongly on the local body cross-section shape, with very little dependence on the upstream shape. Undeflected fins had only a small influence on the pressures on the aft end of the body; however, tail-fin deflections caused large changes in the pressures.

Allen, J. M.↗
NASA NTRS1985

Space shuttle rudder/speedbrake actuation subsystem

The Rudder/Speedbrake (R/SB) Actuation Subsystem for use on the NASA Space Shuttle Orbiter is an electro-hydro-mechanical system which provides the control and positionary capability of the orbiter aero-dynamic primary flight control surface. The system is located in the vehicle's vertical stabilizer. The geared rotary actuators provide a power hinge feature of the split panel rudder. Actuation of both panels in the same direction provides conventional rudder control; actuating the panels differentially provides a speedbrake function intended to control both speed and pitch. The commands may be superimposed on one another. The system consists of one power drive unit which responds to quadredundant avionic signals to generate a rotary output, four geared rotary actuators, which develop rotary position and torque as outputs, and ten torque transmitting drive-shifts.

Naber, R. A.↗
NASA NTRS1985

Precipitation of radiation belt electrons by man-made waves A comparison between theory and measurement

The temporal and spectral shape and the absolute flux level of particle pulses precipitated by a VLF transmitter are examined from a theoretical point of view. A test-particle model of the gyroresonant wave-particle interaction is applied to the parameters of the observed cases for calculating the precipitation characteristics. The temporal shapes of the precipitation pulses are found to be controlled (1) by the pitch angle dependence of the particle distribution near the edge of the loss cone and (2) by the multiple interaction of the particles with the waves due to significant atmospheric backscatter.

Inan, U. S.↗
NASA NTRS1985

Analysis of the free-tip rotor wind-tunnel test results

The results from a wind tunnel test of a small scale free-tip rotor are analyzed. The free-tip rotor has blade tips that are free to weathervane into the tip's relative wind, thus producing a more uniform lift around the azimuth. The free-tip assembly, which includes the controller, functioned flawlessly throughout the test. In a test of the free-tip's response after passing through a vertical air jet, the tip pitched freely and in a controlled manner. Analysis of the tip's response characteristics showed the free-tip system's damped natural frequency to be 5.2 per rev. Tip pitch angle responses to the local airstream are presented for an advance-ratio range of 0.1 to 0.397 and for a solidity weighted rotor lift coefficient range of 0.038 to 0.092. Harmonic analysis of the responses showed a dominance by the first harmonic. As a result of the tip being free, forward flight power requirements were reduced by 8% or more. More power reduction was recorded for high thrust conditions. In addition to the power reduction, flatwise blade bending moments were reduced by as much as 30% at the inboard blade stations.

Stroub, Robert H.↗
NASA NTRS1991

Approximate reasoning-based learning and control for proximity operations and docking in space

A recently proposed hybrid-neutral-network and fuzzy-logic-control architecture is applied to a fuzzy logic controller developed for attitude control of the Space Shuttle. A model using reinforcement learning and learning from past experience for fine-tuning its knowledge base is proposed. Two main components of this approximate reasoning-based intelligent control (ARIC) model - an action-state evaluation network and action selection network are described as well as the Space Shuttle attitude controller. An ARIC model for the controller is presented, and it is noted that the input layer in each network includes three nodes representing the angle error, angle error rate, and bias node. Preliminary results indicate that the controller can hold the pitch rate within its desired deadband and starts to use the jets at about 500 sec in the run.

Berenji, Hamid R.↗
NASA NTRS1992

A combined Earth scanner and momentum wheel for attitude determination and control of small spacecraft

In order to satisfy the stringent cost and power requirements of small satellites, an advanced SCANWHEEL was designed, built, and qualified by ITHACO, Inc. The T-SCANWHEEL is a modular momentum/reaction wheel with an integral conical Earth scanner. The momentum wheel provides momentum bias and control torques about the pitch axis of a spacecraft. An angled scan mirror coupled to the rotating shaft of the momentum wheel provides a conical scan of the field-of-view of an infrared sensor to provide pitch-and-roll attitude information. By using the same motor and bearings for the momentum wheel and Earth scanner, the overall power consumption is reduced and the system reliability is enhanced. The evolution of the T-SCANWHEEL is presented, including design ground rules, tradeoff analyses, and performance results.

Bialke, Bill↗
NASA NTRS1990

Rotor blade-vortex interaction noise reduction and vibration using higher harmonic control

The use of higher harmonic control (HHC) of blade pitch to reduce blade-vortex interaction (BVI) noise is examined by means of a rotor acoustic test. A dynamically scaled, four-bladed, articulated rotor model was tested in a heavy gas (Freon-12) medium. Acoustic and vibration measurements were made for a large range of matched flight conditions where prescribed (open loop) HHC pitch schedules were superimposed on the normal (baseline) collective and cyclic trim pitch. A novel sound power measurement technique was developed to take advantage of the reverberance in the hard walled tunnel. Quantitative sound power results are presented for a 4/rev (4P) collective pitch HHC. By comparing the results using 4P HHC to corresponding baseline (no HHC) conditions, significant midfrequency noise reductions of 5-6 dB are found for low-speed descent conditions where BVI is most intense. For other flight conditions, noise is found to increase with the use of HHC. LF loading noise, as well as fixed and rotating frame vibration levels, show increased levels.

Brooks, Thomas F.↗
NASA NTRS1922

The Use of Multiplied Pressures for Automatic Altitude Adjustments

The efficient performance of an airplane requires that certain adjustments be made as the density of the air through which the airplane passes changes. The safety of the over-dimensioned aircraft engine depends upon careful manipulation of spark advance and throttle opening and a proper control of a variable pitch propeller, if the maximum performance of the supercharged engine is to be obtained. It is evident that there is a real need for satisfactory devices to make such adjustments automatically. Discussed here is a method of automatic compensation which deserves consideration in the design of such devices. Existing schemes for automatic compensation all depend upon some contrivance which functions primarily because of changes in atmospheric pressure. In these devices a leak in the supposedly tight chamber means utter failure. The elimination of this source of danger is one of the aims of the method of altitude compensation described here. The change suggested is to make the source of operation the difference between atmospheric pressure and some multiple of atmospheric pressure instead of the difference between the atmospheric pressure and that of the gas confined in a tight chamber. The design of a device based on this method of altitude compensation is given.

Sparrow, Stanwood S↗
NASA NTRS1940

Longitudinal stability and control with special reference to slipstream effects

Report presents the results of a study of data obtained in the NACA full-scale wind tunnel concerning the effects of interference and of propeller operation on longitudinal stability and control. The data include pitching moments for various power conditions for airplanes with tails removed and with tails set at various stabilizer and elevator angles. A number of surveys of the dynamic pressure and the flow direction in the region of the horizontal tail surface are also included. Results are given for eight airplanes, including a model of a four-engine airplane tested both as a tractor and as a pushed and a model of two-engine pusher. The effects are shown of propeller operation on the downwash angles and the dynamic pressures at the tail and on the pitching-moment contribution of the propeller and the wing.

Katzoff, S↗
NASA NTRS2002

Recent Flight Results of the TRMM Kalman Filter

The Tropical Rainfall Measuring Mission (TRMM) spacecraft is a nadir pointing spacecraft that nominally controls the roll and pitch attitude based on the Earth Sensor Assembly (ESA) output. TRMM's nominal orbit altitude was 350 km, until raised to 402 km to prolong mission life. During the boost, the ESA experienced a decreasing signal to noise ratio, until sun interference at 393 km altitude made the ESA data unreliable for attitude determination. At that point, the backup attitude determination algorithm, an extended Kalman filter, was enabled. After the boost finished, TRMM reacquired its nadir-pointing attitude, and continued its mission. This paper will briefly discuss the boost and the decision to turn on the backup attitude determination algorithm. A description of the extended Kalman filter algorithm will be given. In addition, flight results from analyzing attitude data and the results of software changes made onboard TRMM will be discussed. Some lessons learned are presented.

Andrews, Stephen F.↗
NASA NTRS1973

The effects of an autopilot on airplane responses to turbulence with emphasis on tail loads

An analytical study has been made to assess the loads developed on the horizontal tail of an autopilot-controlled rigid airplane flying in one-dimensional atmospheric turbulence. The root-mean-square values of rigid-airframe responses and tail-load responses were calculated at five flight conditions, and the behavior of these responses was observed in two autopilot modes: pitch-attitude-hold mode and altitude-control mode. It was found that pitch attitude and altitude can be controlled by the simple autopilot with acceptable or no increases in tail loads.

Perry, B., III↗
NASA NTRS1961

Flight Tests of a 1/6-Scale Model of the Hawker P 1127 Jet VTOL Airplane

An experimental investigation has been made to determine the dynamic stability and control characteristics of a 1/6-scale flying model of the Hawker P lIP7 jet vertical-take-off-and-landing (VTOL) airplane in hovering and transition flight. The model was powered by a counter-rotating ducted fan driven by compressed-air jets at the tips of the fan blades. In hovering flight the model was controlled by jet-reaction controls which consisted of yaw and pitch jets at the extremities of the fuselage and a roll jet on each wing tip. In forward flight the model was controlled by conventional ailerons and rudder and an all-movable horizontal tail. In hovering flight the model could be flown smoothly and easily, but the roll control was considered too weak for rapid maneuvering or hovering in gusty air. Transitions from hovering to normal forward flight and back to hovering could be made smoothly and consistently and with only moderate changes in longitudinal trim. The model had a static longitudinal instability or pitch-up tendency throughout the transition range, but the rate of divergence in the pitch-up was moderate and the model could be controlled easily provided the angle of attack was not allowed to become too high. In both the transition and normal forward flight conditions the lateral motions of the model were difficult to control at high angles of attack, apparently because of low directional stability at small angles of sideslip. The longitudinal stability of the model in normal forward flight was generally satisfactory, but there was a decided pitch-up tendency for the flap-down condition at high angles of attack. In the VTOL landing approach condition, with the jets directed straight down or slightly forward, the nose-down pitch trim required was greater than in the transitions from hovering to forward flight, but the longitudinal instability was about the same. Take-offs and landings in still air could be made smoothly although there was a slight unfavorable ground effect on lift and a nose-down change in pitch trim near the ground. Short take-offs and landings could be made smoothly and consistently although the model experienced a decided nose-up change in pitching moment as it climbed out of ground effect.

Smith, Charles C., Jr.↗