Search NASA⌕ Search

SEARCH · Search NASA

Results for “Predictive analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Study of Spray Disintegration in Accelerating Flow Fields

An analytical and experimental investigation was conducted to perform "proof of principlem experiments to establish the effects of propellant combustion gas velocity on propella'nt atomization characteristics. The propellants were gaseous oxygen (GOX) and Shell Wax 270. The fuel was thus the same fluid used in earlier primary cold-flow atomization studies using the frozen wax method. Experiments were conducted over a range in L* (30 to 160 inches) at two contraction ratios (2 and 6). Characteristic exhaust velocity (c*) efficiencies varied from SO to 90 percent. The hot fire experimental performance characteristics at a contraction ratio of 6.0 in conjunction with analytical predictions from the drovlet heat-up version of the Distributed Energy Release (DER) combustion computer proDam showed that the apparent initial dropsize compared well with cold-flow predictions (if adjusted for the gas velocity effects). The results also compared very well with the trend in perfomnce as predicted with the model. significant propellant wall impingement at the contraction ratio of 2.0 precluded complete evaluation of the effect of gross changes in combustion gas velocity on spray dropsize.

Nurick, W. H.↗

Metallic positive expulsion diaphragms

High-cycle life ring-reinforced hemispherical type positive expulsion diaphragm performance was demonstrated by room temperature fluid expulsion tests of 13" diameter, 8 mil thick stainless steel configurations. A maximum of eleven (11) leak-free, fluid expulsions were achieved by a 25 deg cone angle diaphragm hoop-reinforced with .110-inch cross-sectional diameter wires. This represents a 70% improvement in diaphragm reversal cycle life compared to results previously obtained. The reversal tests confirmed analytic predictions for diaphragm cycle life increases due to increasing values of diaphragm cone angle, radius to thickness ratio and material strain to necking capacity. Practical fabrication techniques were demonstrated for forming close-tolerance, thin corrugated shells and for obtaining closely controlled reinforcing ring stiffness required to maximize diaphragm cycle life. A non-destructive inspection technique for monitoring large local shell bending strains was developed.

Gleich, D.↗

Centaur space vehicle pressurized propellant feed system tests

Engine firing tests, using a full-scale flight-weight vehicle, were performed to evaluate a pressurized propellant feed system for the Centaur. The pressurant gases used were helium and hydrogen. The system was designed to replace the boost pumps currently used on Centaur. Two liquid oxygen tank pressurization modes were studied: (1) directly into the ullage and (2) below the propellant surface. Test results showed the two Centaur RL10 engines could be started and run over the range of expected flight variables. No system instabilities were encountered. Measured pressurization gas quantities agreed well with analytically predicted values.

Source record↗

Simulation of ERTS RBV imagery.

Based on the signal-to-noise ratio, modulation transfer function (MTF), and light transfer characteristics of the return-beam vidicon (RBV) multispectral three-camera subsystem, developed for use on earth resources technology satellites (ERTS), an analytical prediction of the resolvability of ground targets was made as a function of target size, contrast, spectral distribution, and radiance level. To determine whether the analysis was correct, U.S. Air Force targets with various contrasts were utilized to simulate those contrasts and radiance levels that the RBV cameras would see in the actual ERTS scenes. Although the RBV camera used in this test had a somewhat lower signal-to-noise ratio than the flight cameras, the simulation still proved the validity of the theoretical analysis in predicting resolving power performance for any set of input parameters.

Weinstein, O.↗

Use of leaning vanes for fan noise reduction.

The obliquity of blade-vane interactions in an axial fan and its influence on noise generation are examined. Analysis indicates that leaning vanes decrease the amplitudes of the fluctuating pressures at the rotor-stator plane and modify the radial distribution. These changes lead to considerable cancellation in the near field and consequent reduction in radiated acoustic power. Acoustic measurements on a small scale fan with radial and leaning vanes compare favorably with analytical predictions.

Rao, G. V. R.↗

Experimental investigation of recirculating cells in laminar coaxial jets.

Utilizing several unique means of introducing smoke into the flow field for careful visualization in addition to hot-wire techniques, experiments are performed in a specially designed facility producing laminar flows up to considerably high Reynolds numbers. Characteristics of the cells and the flow conditions that bring them about are documented by smoke photographs in the Reynolds number velocity ratio plane and the results are compared to previous analytical predictions. The cells are found to fall into three categories with different flow characteristics involving unsteadiness in position, and shear layer instabilities which result in higher mixing with the outer streams.-

Warpinski, N. R.↗

Silica reinforcement and char reactions in the Apollo heat shield.

Reactions of the silica reinforcement fiber and ablation char of the Apollo heat shield have been investigated by laboratory tests in an arc image furnace (at temperature levels up to 5000 R, pressures up to 0.7 atm, and heat flux similar to reentry) and by an actual reentry test. Microchemical analyses and X-ray diffraction studies have been made to determine the presence of SiC formation in the char. Experimental data and analytical predictions of thermal and density profiles have been compared for the ablation of virgin heat shield and precharred materials to determine the effects of SiC formation on ablation performance. In all analyses, general agreement was found between chemical composition and the thermal predictions for laboratory tests and reentry materials. In all ablated materials, SiC was formed in the front surface of the char. The highest SiC content found was 58% by weight and found in a high-pressure environment. The SiC formed was found to act as a heat sink in the ablation process and can lower the front surface temperature by 300 R.

Cagliostro, D. E.↗

Applications of optical holography to applied mechanics.

This paper provides a brief summary of applications of optical holography and holographic interferometry to applied solid mechanics. Basic equations commonly used in fringe interpretation are described and used to reduce the data contained on holographic interferograms. A comparison of data obtained holographically with analytical prediction is given wherever possible. Applications contained herein include front surface physics, study of bomb breakup, transverse wave propagation, study of mode shapes of panels at elevated temperatures, nondestructive testing, and vibration analysis.

Aprahamian, R.↗

Analytic and experimental performance of two isentropic mixed compression axisymmetric inlets at Mach numbers 0.8 to 2.65

A mixed compression axisymmetric inlet model with a capture diameter of 50 cm was tested at Mach numbers ranging from 0.8 to 2.65 at 0 deg angle of attack and a constant total pressure of approximately 1 atm. Analytical methods accounting for the effects of both viscous and inviscid flows and incorporating empirical bleed discharge coefficients were used in the procedure for designing the inlet contours and the bleed system. Experimental results are compared with analytic predictions and are also compared with results from earlier tests of an inlet with the same internal contours but with a bleed system developed by cut and try methods in the wind tunnel. With the bleed configuration predicted by the design procedure, maximum total pressure recovery at the engine face at the design Mach number of 2.65 was 93 percent, with a total pressure distortion less than 10 percent. Corresponding bleed mass flow was approximately 7.5 percent, which was about 1.3 percent less than predicted. At lower supersonic Mach numbers, pressure recovery and bleed were generally lower and distortion generally higher.

Smeltzer, D. B.↗

A kinematic eddy viscosity model including the influence of density variations and preturbulence

A model for the kinematic eddy viscosity was developed which accounts for the turbulence produced as a result of jet interactions between adjacent streams as well as the turbulence initially present in the streams. In order to describe the turbulence contribution from jet interaction, the eddy viscosity suggested by Prandtl was adopted, and a modification was introduced to account for the effect of density variation through the mixing layer. The form of the modification was ascertained from a study of the compressible turbulent boundary layer on a flat plate. A kinematic eddy viscosity relation which corresponds to the initial turbulence contribution was derived by employing arguments used by Prandtl in his mixing length hypothesis. The resulting expression for self-preserving flow is similar to that which describes the mixing of a submerged jet. Application of the model has led to analytical predictions which are in good agreement with available turbulent mixing experimental data.

Cohen, L. S.↗

Performance of statistical energy analysis

Statistical energy analysis (SEA) methods have been developed for high frequency modal analyses on random vibration environments. These SEA methods are evaluated by comparing analytical predictions to test results. Simple test methods are developed for establishing SEA parameter values. Techniques are presented, based on the comparison of the predictions with test values, for estimating SEA accuracy as a function of frequency for a general structure.

Davis, R. F.↗

S-2 stage 1/25 scale model base region thermal environment test. Volume 1: Test results, comparison with theory and flight data

A 1/25 scale model S-2 stage base region thermal environment test is presented. Analytical results are included which reflect the effect of engine operating conditions, model scale, turbo-pump exhaust gas injection on base region thermal environment. Comparisons are made between full scale flight data, model test data, and analytical results. The report is prepared in two volumes. The description of analytical predictions and comparisons with flight data are presented. Tabulation of the test data is provided.

Sadunas, J. A.↗

Cyclic arc plasma tests of RSI materials using a preheater

The results of a test program are reported in which a preheater was used with an arc plasma stream to study the thermal response of samples of candidate reusable surface insulation materials for the space shuttle. The preheater simulated the shuttle temperature history during the first and last portions of the test cycle, which could not be simulated by the air arc plasma flow. Pre- and post-test data taken for each of the materials included magnified views, optical properties, and chemical analyses. The test results indicate that the mullite base samples experience higher surface temperatures than the other materials at heating rates greater than 225 kw/sq m. The ceramic fibrous mullite and silica coatings show noncatalytic wall behavior. Internal temperature response data for the materials are compared and correlated with analytical predictions.

Stewart, D. A.↗

Evaluation of acoustic cavities for combustion stabilization.

The stabilizing influence of acoustic cavities (quarterwave acoustic resonators) on acoustic modes of combustion instability has been studied. The ability to analytically predict cavity damping was improved. Relatively good agreement between predicted damping and measured stability was demonstrated. Full-scale motor firings were made to evaluate the influence of several parameters on stability. Results from these firings showed that stability was changed, but not dramatically, by changes in the engine operating conditions. Variations in the film-coolant flowrate do not significantly affect cavity stabilization. The ability to stabilize an engine with unconventional cavity configurations was demonstrated.

Oberg, C. L.↗

Multiple soliton production and the Korteweg-de Vries equation.

Compressive square-wave pulses are launched in a double-plasma device. Their evolution is interpreted according to the Korteweg-de Vries description of Washimi and Taniuti. Square-wave pulses are an excitation for which an explicit solution of the Schrodinger equation permits an analytical prediction of the number and amplitude of emergent solitons. Bursts of energetic particles (pseudowaves) appear above excitation voltages greater than an electron thermal energy, and may be mistaken for solitons.

Hershkowitz, N.↗

Silicon-germanium technology program of the Jet Propulsion Laboratory.

The outer planetary exploration missions studied by the Jet Propulsion Laboratory require silicon-germanium radioisotope thermoelectric generators (RTGs) in which the factors of safety are as low as is compatible with the reliable satisfaction of the power needs. Work on silicon germanium sublimation performed at the Jet Propulsion Laboratory is presented. Analytical modeling work on the solid-diffusion process involved in the steady-state (free) sublimation of silicon germanium is described. Analytical predictions are made of the sublimation suppression which can be achieved by using a cover gas. A series of accelerated (high-temperature) tests which were performed on simulated hardware (using four SiGe couples) to study long-term sublimation and reaction mechanisms are also discussed.

De Winter, F.↗

Rotor noise due to inflow turbulence.

The interaction of turbulent velocity fluctuations of the inflow with rotor blades and the resulting acoustic radiation is examined in terms of: dipole sources due to blade loading, monopole sources due to thickness of the rotating blades, and quadrupole sources due to velocity fluctuations in the flow region. Depending upon the length and time scales of the turbulence, sufficient number of blades may interact with a coherent eddy to radiate noise with discrete peaks at blade passing frequency and its harmonics. Theoretical estimates of acoustic radiation to on-axis points from a typical subsonic rotor are presented, and it is noted that the discrete tone noise is primarily from dipole radiation. Discrete tone noise levels observed in narrow band analysis of test data show reasonable agreement with analytical predictions.

Rao, G. V. R.↗

Three-dimensional hypersonic transitional/turbulent mean flow profiles.

Detailed three-dimensional compressible transitional/turbulent boundary-layer profiles are presented for use as test cases in numerical and integral calculation procedures. The profiles were obtained from tests conducted in the Mach 20 leg of the Langley High Reynolds Number Helium Facility. The presented data represent an arduous test case for analytical prediction methods, since 'low Reynolds number' and precursor transition effects should probably be accounted for to accurately predict the boundary-layer growth and development.

Fischer, M. C.↗