Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLIDING CONTACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Pressure perturbation in EHD contacts due to an ellipsoidal asperity

The pressure fluctuations around an ellipsoidal asperity tip at the inlet region of an elastohydrodynamic contact is determined by solving a perturbed Reynolds equation assuming that the asperity shape is unaffected by the perturbed pressure. Results are presented as the amplitude of the perturbed pressure as a function of ellipticity ratio, maximum Hertzian pressure, nominal EHD film thickness, asperity size, asperity height, and pressure viscosity coefficient. For the case of simple sliding between a smooth surface and a stationary asperity, a comparison is also made between the results for large ellipticity ratios and the pressure fluctuations obtained by using a previous line contact EHD analysis for a two-dimensional asperity ridge. The agreement is found to be close for moderate Hertzian pressure and relatively thick EHD film thickness.

Chow, L. S. H.↗

Off axis loading of silicon carbide fibers in a titanium aluminide matrix

Silicon carbide SCS-6 fibers in a Ti24A1 + 11Nb matrix were subjected to off axis loading in a 'thin-slice' pushout test, resulting in various combinations of shear, radial compression, and tension along the fibers as a function of orientation angle. The load necessary for debonding decreased as the orientation angle increased, whereas the average frictional sliding stress after 60 s of sliding remained relatively constant for orientation angles less than 30 deg. Analyses of the specimen bending stresses and of the contact stresses by finite element modeling and thin plate theory are presented.

Kennefick, C. M.↗

Oxygen and sulfur interactions with a clean iron surface and the effect of rubbing contact on these interactions

An investigation was conducted to determine the nature of the chemical interactions of oxygen and sulfur with iron when surfaces are stationary and also during sliding in a vacuum environment. Various gases that contained sulfur, oxygen, or both were adsorbed to iron at 23 C. The gases included oxygen, hydrogen sulfide, methyl mercaptan, and sulfur dioxide. Friction experiments were conducted with a hemispherical rider sliding on a rotating disk. An Auger cylindrical mirror analyzer was used to monitor the iron surface chemistry. The results of this study indicate that oxygen will completely displace sulfide films from iron surfaces. Organic thiols containing sulfur, such as methyl mercaptan, adsorb to an iron surface dissociatively. Only sulfur is detected on the iron surface. Sliding inhibits the formation of sulfide films on iron with the adsorption of hydrogen sulfide and methyl mercaptan. With oxygen and sulfur dioxide, the sliding process does not affect adsorption behavior.

Buckley, D. H.↗

Mechanical contact induced transformation from the amorphous to the crystalline state in metallic glass

Friction and wear tests were conducted with 3.2- and 6.4-millimeter-diameter aluminum oxide spheres sliding, in reciprocating motion, on a Fe67Co18B14Si1 metallic foil. Crystallites with a size range of 10 to 150 nanometers were produced on the wear surface of the amorphous alloy. A strong interaction between transition metals and metalloids such as silicon and boron results in strong segregation during repeated sliding, provides preferential transition metal-metalloid clustering in the amorphous alloy, and subsequently produces the diffused honeycomb structure formed by dark grey bands and primary crystals, that is, alpha-Fe in the matrix. Large plastic flow occurs on an amorphous alloy surface with sliding and the flow film of the alloy transfers to the aluminum oxide pin surface. Multiple slip bands due to shear deformation are observed on the side of the wear track. Two distinct types of wear debris were observed as a result of sliding: an alloy wear debris, and/or powdery-whiskery oxide debris.

Miyoshi, K.↗

Tribological Properties of Cr(Si)CN Coatings Sliding Against Different Mating Balls in Water

Chromium carbon nitride coatings have potential industrial applications in aqueous environments due to their good tribological properties and corrosion resistance. In order to reveal the effect of silicon doping on the tribological properties of CrCN coating, the tribological properties of Cr(Si)CN coatings sliding against potential sliding partners (Si{sub 3}N{sub 4}, Al{sub 2}O{sub 3} and SUS440C balls) in water were discussed. The results showed that the coefficient of friction (COF) for different partners could be arranged as μ{sub Al2O3} < μ{sub Si3N4} < μ{sub SUS440C} regardless of coatings. This result was determined by the tribochemical reaction, oxidation resistance and contact pressures of tribopairs. After the incorporation of Si element, the friction behavior of CrCN coating was improved due to the friction-induced hydration of amorphous silicon compound phase as sliding against Si{sub 3}N{sub 4} and SUS440C balls.

36 MATERIALS SCIENCE↗

Tribological interaction between polytetrafluoroethylene and silicon oxide surfaces

We investigated the tribological interaction between polytetrafluoroethylene (PTFE) and silicon oxide surfaces. A simple rig was designed to bring about a friction between the surfaces via sliding a piece of PTFE on a thermally oxidized silicon wafer specimen. A very mild inclination (∼0.5°) along the sliding motion was also employed in order to monitor the tribological interaction in a gradual manner as a function of increasing contact force. Additionally, some patterns were sketched on the silicon oxide surface using the PTFE tip to investigate changes produced in the hydrophobicity of the surface, where the approximate water contact angle was 45° before the transfer. The nature of the transferred materials was characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). XPS results revealed that PTFE was faithfully transferred onto the silicon oxide surface upon even at the slightest contact and SEM images demonstrated that stable morphological changes could be imparted onto the surface. The minimum apparent contact pressure to realize the PTFE transfer is estimated as 5 kPa, much lower than reported previously. Stability of the patterns imparted towards many chemical washing processes lead us to postulate that the interaction is most likely to be chemical. Contact angle measurements, which were carried out to characterize and monitor the hydrophobicity of the silicon oxide surface, showed that upon PTFE transfer the hydrophobicity of the SiO{sub 2} surface could be significantly enhanced, which might also depend upon the pattern sketched onto the surface. Contact angle values above 100° were obtained.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron Tomography of Cryofixed, Isometrically Contracting Insect Flight Muscle Reveals Novel Actin-Myosin Interactions

Isometric muscle contraction, where force is generated without muscle shortening, is a molecular traffic jam in which the number of actin-attached motors is maximized and all states of motor action are trapped with consequently high heterogeneity. This heterogeneity is a major limitation to deciphering myosin conformational changes in situ. We used multivariate data analysis to group repeat segments in electron tomograms of isometrically contracting insect flight muscle, mechanically monitored, rapidly frozen, freeze substituted, and thin sectioned. Improved resolution reveals the helical arrangement of F-actin subunits in the thin filament enabling an atomic model to be built into the thin filament density independent of the myosin. Actin-myosin attachments can now be assigned as weak or strong by their motor domain orientation relative to actin. Myosin attachments were quantified everywhere along the thin filament including troponin. Strong binding myosin attachments are found on only four F-actin subunits, the 'target zone', situated exactly midway between successive troponin complexes. They show an axial lever arm range of 77{sup o}/12.9 nm. The lever arm azimuthal range of strong binding attachments has a highly skewed, 127{sup o} range compared with X-ray crystallographic structures. Two types of weak actin attachments are described. One type, found exclusively in the target zone, appears to represent pre-working-stroke intermediates. The other, which contacts tropomyosin rather than actin, is positioned M-ward of the target zone, i.e. the position toward which thin filaments slide during shortening. We present a model for the weak to strong transition in the myosin ATPase cycle that incorporates azimuthal movements of the motor domain on actin. Stress/strain in the S2 domain may explain azimuthal lever arm changes in the strong binding attachments. The results support previous conclusions that the weak attachments preceding force generation are very different from strong binding attachments.

59 BASIC BIOLOGICAL SCIENCES↗

Nonlinear Finite Elements [Slides]

The presentation begins with why we need nonlinear finite elements: Real systems rarely (if ever) behave in a linear fashion during real deformation (Nonlinear material response (plasticity, nonlinear elasticity, . . . ), Contact, Multi-phase/physics interactions); Our boundary conditions may be nonlinear as well; and, Large deformation/rotation is inherently nonlinear. The remainder of topics include: 1D Motivation; Initial de nitions and background; Balance Equations; Weak form and Galerkin form; Newton-Raphson solution of nonlinear equations; and, Alternatives to Newton-Raphson

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Mechanical-contact-induced transformation from the amorphous to the partially crystalline state in metallic glass

Friction and wear tests were conducted with 3.2- and 6.4-millimeter-diameter aluminum oxide spheres sliding, in reciprocating motion, on a Fe67Co18B14Si1 metallic foil. Crystallites with a size range of 10 to 150 nanometers were produced on the wear surface of the amorphous alloy. A strong interaction between transition metals and metalloids such as silicon and boron results in strong segregation during repeated sliding, provides preferential transition metal-metalloid clustering in the amorphous alloy, and subsequently produces the diffused honeycomb structure formed by dark grey bands and primary crystals, that is, alpha-Fe in the matrix. Large plastic flow occurs on an amorphous alloy surface with sliding and the flow film of the alloy transfers to the aluminum oxide pin surface. Multiple slip bands due to shear deformation are observed on the side of the wear track. Two distinct types of wear debris were observed as a result of sliding: an alloy wear debris, and/or powdery-whiskery oxide debris.

Miyoshi, K.↗

Friction and wear of ceramics

The adhesion, friction, wear and lubricated behaviors of both oxide and non-oxide ceramics are reviewed. Ceramics are examined in contact with themselves, other harder materials and metals. Elastic, plastic and fracture behavior of ceramics in solid state contact is discussed. The contact load necessary to initiate fracture in ceramics is shown to be appreciably reduced with tangential motion. Both friction and wear of ceramics are anisotropic and relate to crystal structure as with metals. Grit size effects in two- and three-body abrasive wear are observed for ceramics. Both free energy of oxide formation and the d valence bond character of metals are related to the friction and wear characteristics for metals in contact with ceramics. Surface contaminants affect friction and adhesive wear. For example, carbon on silicon carbide and chlorine on aluminum oxide reduce friction while oxygen on metal surfaces in contact with ceramics increases friction. Lubrication increases the critical load necessary to initiate fracture of ceramics both in indentation and with sliding or rubbing.

Buckley, D. H.↗

Tribological properties of structural ceramics

The tribological and lubricated behavior of both oxide and nonoxide ceramics are reviewed in this chapter. Ceramics are examined in contact with themselves, other harder materials and metals. Elastic, plastic and fracture behavior of ceramics in solid state contact is discussed. The contact load necessary to initiate fracture in ceramics is shown to be appreciably reduced with tangential motion. Both friction and wear of ceramics are anisotropic and relate to crystal structure as has been observed with metals. Grit size effects in two and three body abrasive wear are observed for ceramics. Both free energy of oxide formation and the d valence bond character of metals are related to the friction and wear characteristics for metals in contact with ceramics. Surface contaminants affect friction and adhesive wear. For example, carbon on silicon carbide and chlorine on aluminum oxide reduce friction while oxygen on metal surfaces in contact with ceramics increases friction. Lubrication increases the critical load necessary to initiate fracture of ceramics both in indentation and with sliding or rubbing. Ceramics compositions both as coatings and in composites are described for the high temperature lubrication of both alloys and ceramics.

Buckley, D. H.↗

Mechanical-contact-induced transformation from the amorphous to the partially crystalline state in metallic glass

Friction and wear tests were conducted with 3.2- and 6.4-millimeter-diameter aluminum oxide spheres sliding, in reciprocating motion, on a Fe67Co18B14Si1 metallic foil. Crystallites with a size range of 10 to 150 nanometers were produced on the wear surface of the amorphous alloy. A strong interaction between transition metals and metalloids such as silicon and boron results in strong segregation during repeated sliding, provides preferential transition metal-metalloid clustering in the amorphous alloy, and subsequently produces the diffused honeycomb structure formed by dark grey bands and primary crystals, that is, alpha-Fe in the matrix. Large plastic flow occurs on an amorphous alloy surface with sliding and the flow film of the alloy transfers to the aluminum oxide pin surface. Multiple slip bands due to shear deformation are observed on the side of the wear track. Two distinct types of wear debris were observed as a result of sliding: an alloy wear debris, and/or powdery-whiskery oxide debris.

Miyoshi, K.↗

Friction and wear of ceramics

The adhesion, friction, wear, and lubricated behaviors of both oxide and non-oxide ceramics are reviewed. Ceramics are examined in contact with themselves, other harder materials, and metals. Elastic, plastic, and fracture behavior of ceramics in solid state contact is discussed. The contact load necessary to initiate fracture in ceramics is shown to be appreciably reduced with tangential motion. Both friction and wear of ceramics are anisotropic and relate to crystal structure as with metals. Grit size effects in two and three body abrasive wear are observed for ceramics. Both the free energy of oxide formation and the d valence bond character of metals are related to the friction and wear characteristics for metals in contact with ceramics. Surface contaminants affect friction and adhesive wear. For example, carbon on silicon carbide and chlorine on aluminum oxide reduce friction while oxygen on metal surfaces in contact with ceramics increases friction. Lubrication increases the critical load necessary to initiate fracture of ceramics both in indentation and with sliding or rubbing.

Buckley, Donald H.↗

Tribological properties of structural ceramics

The tribological and lubricated behavior of both oxide and nonoxide ceramics are reviewed in this chapter. Ceramics are examined in contact with themselves, other harder materials and metals. Elastic, plastic and fracture behavior of ceramics in solid state contact is discussed. The contact load necessary to initiate fracture in ceramics is shown to be appreciably reduced with tangential motion. Both friction and wear of ceramics are anisotropic and relate to crystal structure as has been observed with metals. Grit size effects in two and three body abrasive wear are observed for ceramics. Both free energy of oxide formation and the d valence bond character of metals are related to the friction and wear characteristics for metals in contact with ceramics. Surface contaminants affect friction and adhesive wear. For example, carbon on silicon carbide and chlorine on aluminum oxide reduce friction while oxygen on metal surfaces in contact with ceramics increases friction. Lubrication increases the critical load necessary to initiate fracture of ceramics both in indentation and with sliding or rubbing. Ceramics compositions both as coatings and in composites are described for the high temperature lubrication of both alloys and ceramics.

Buckley, Donald H.↗

Friction Properties of Surface-Fluorinated Carbon Nanotubes

Surface modification of the tubular or sphere-shaped carbon nanoparticles through chemical treatment, e.g., fluorination, is expected to significantly affect their friction properties. In this study, a direct fluorination of the graphene-built tubular (single-walled carbon nanotubes) structures has been carried out to obtain a series of fluorinated nanotubes (fluoronanotubes) with variable C(n)F (n =2-20) stoichiometries. The friction coefficients for fluoronanotubes, as well as pristine and chemically cut nanotubes, were found to reach values as low as 0.002-0.07, according to evaluation tests run in contact with sapphire in air of about 40% relative humidity on a ball-on-disk tribometer which provided an unidirectional sliding friction motion. These preliminary results demonstrate ultra-low friction properties and show a promise in applications of surface modified nanocarbons as a solid lubricant.

Wal, R. L. Vander↗

Surface chemistry and wear behavior of single-crystal silicon carbide sliding against iron at temperatures to 1500 C in vacuum

X-ray photoelectron and Auger electron spectroscopy analyses and morphological studies of wear and metal transfer were conducted with a single-crystal silicon carbide 0001 surface in contact with iron at various temperatures to 1500 C in a vacuum of 10 to the minus 8th power pascal. The results indicate that below 800 C, carbide-carbon and silicon are primarily seen on the silicon carbide surface. Above 800 C the graphite increases rapidly with increase in temperature. The outermost surficial layer, which consists mostly of graphite and little silicon at temperatures above 1200 C is about 2 nm thick. A thicker layer, which consists of a mixture of graphite, carbide, and silicon is approximately 100 nm thick. The closer the surface sliding temperature is to 800 C, the more the metal transfer produced. Above 800 C, there was a transfer of rough, discontinuous, and thin iron debris instead of smooth, continuous and thin iron film which was observed to transfer below 800 C. Two kinds of fracture pits were observed on the silicon carbide surface: (1) a pit with a spherical asperity; and (2) multiangular shaped pits.

Miyoshi, K.↗

High temperature flexible seal

This device is concerned with sealing the sliding interfaces between structural panels that are roughly perpendicular to each other or whose edges are butted against one another. The gap which the seal element must seal is not uniform along the seal length requiring significant seal flexibility. The seal is mounted in a rectangular groove in a moveable structural panel. The seal comprises a plurality of rectangular shaped wafers stacked next to one another and preloaded in the axial direction to minimize leakage between wafers. The wafers are laterally preloaded to maintain sealing contact along the wafer faces which engage the adjacent wall of a sidewall using one of several approaches, such as the pressurized linear bellows. The seal accommodates distortions in the adjacent panel by relative sliding between adjacent wafers. Leakage between wafers is further minimized with good wafer surface finishes. Leakage between the seal nose and the adjacent structural panel is minimized when sealing against a distorted sidewall with relatively thin wafers and suitable seal preload apparatus. Leakage behind the seal is minimized with good groove tolerances and good sealing contact between the preload system and the back of the peripheral edge of the wafers.

Steinetz, Bruce M.↗

Formation and dissociation of shear-induced high-energy dislocations: insight from molecular dynamics simulations

Solid-phase processing (SPP) allows one to create complex microstructures, not achievable via thermal processing alone. The resulting structures exhibit a rich palette of defects, both thermal and non-thermal, including defect substructures, such as dislocation networks. It is essential to understand the mechanisms of deformation and defect structure formation to guide SPP towards achieving desired microstructures and material properties. In this study, large-scale molecular dynamics simulations are used to investigate the effects of inhomogeneous strain distribution, that mimics deformation conditions of tribological tests, on the evolution of defects under severe shear deformation in polycrystalline Al. Analysis of defect nucleation and reaction pathways reveals that strong geometric constraints suppress the nucleation and slide of low energy dislocation 1/2$\langle110\rangle${111} but promote the nucleation and slide of high energy dislocations, such as [$1\bar1$0] (001) and 1/2 [$1\bar1$$\bar2$]($1\bar1$1). Further, a rough contact surface, characteristic to tribological tests, imposes an inhomogeneous stress field leading to inhomogeneous defect substructures due to location-dependent activation of slip systems. The results suggest that high-energy dislocations can dominate the evolution of grain structures in highly constrained environments, which should be considered in modeling plastic deformation and grain refinement during SPP.

42 ENGINEERING↗