Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS - CLEANING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Effect of cold forging on the microstructure and corrosion behavior of type 316L stainless steel in molten FLiNaK salt

Here, the effect of cold forging on the microstructure and corrosion behavior of 316L stainless steel (SS) in molten salt was investigated. Static corrosion experiments were performed in FLiNaK (LiF-NaF-KF: 46.5–11.5–42 mol.%) at 600 °C for 50 h in a glove box. The results show that cold forging gives rise to enhanced corrosion of 316L SS in molten fluoride salt due to the increase of crystallographic defects. Based on the potentiodynamic polarization results, the corrosion current density of 50 % cold-forged 316L SS is about 2.1 times larger than that of the as-received 316L SS in molten FLiNaK salt at 600 °C.

316L stainless steel↗
DOE OSTI2025

Deformation band corrosion as a result of applied stress and cold-work in 304 stainless steel in simulated pressurized water reactor primary water conditions

Stainless steels like 304SS are commonly used in pressurized water reactor primary water environments due to their excellent resistance to stress corrosion cracking (SCC). However, SCC susceptibility has been observed in cold-worked 304SS. Cold-rolling introduces a high density of defects, such as deformation bands or dislocations, into the microstructure; applied stress, even if macroscopically below the yield stress, can result in regions with high localized stresses. Cold-worked and non-cold-worked samples were exposed to 360 °C simulated PWR primary water for 1500 h with and without active loading. Corrosion susceptibility of dislocations and deformation bands induced by cold-rolling and/or applied stress was studied using high-resolution (analytical) transmission electron microscopy. Deformation bands were generated in all specimens examined in the study. Penetrative oxidation was observed in some deformation bands in each specimen. The depth of penetrative deformation band oxidation frequently exceeded the depth of grain boundary oxidation in all specimens. However, deformation band oxides generally were narrowly confined to the deformation band plane. Highly Ni-rich regions were observed beyond all oxidation fronts. Surface oxides were thicker in the specimens exposed under active loading. In conclusion, the implications of these findings at surfaces for deformation bands intersecting stress corrosion crack paths are discussed.

EFTEM↗
DOE OSTI2025

Characterization of in-situ and ex-situ ion-irradiated additively manufactured 316L and 316H stainless steels

Additively manufactured (AM) 316 stainless steel (SS) differs from its wrought counterpart in its unique dislocation cell structure and the presence of segregation and oxide particles at the cell walls. This work investigated the evolution of the microstructure in laser powder bed fusion (LPBF) 316L and 316H SS under in-situ 1 MeV Kr ion irradiation at 600 °C to 5 dpa, and ex-situ 4 MeV Ni ion irradiation at 300 °C and 600 °C from 0.2 dpa to 10 dpa, with a dose rate for all experiments of 10 -3 dpa/s. The results reveal that the dislocation cell structure results in heterogeneous formation of dislocation loops and voids, particularly at 600 °C, where loops tend to form within the cell interiors while voids form at the cell boundaries. LPBF 316H has a reduced level of swelling compared to LPBF 316L due to prolonged incubation. Energy Dispersive X-ray Spectroscopy (EDS) mapping indicates Ni and Si segregation at void surfaces due to radiation-induced segregation. At 300 °C, where voids are absent, the distribution of dislocation loops and stacking fault tetrahedra appears to be uniform. Dislocation cell structures mostly disappeared by 2 dpa for all conditions in this work. M 23 C 6 carbides were observed in LPBF 316H at 600 °C as early as 0.2 dpa, but not in LPBF 316L. Nanoindentation was performed to obtain the hardness of irradiated materials. In conclusion, this work illustrated the influence of additive manufacturing processes on microstructure evolution under irradiation, revealing the differences as well as the similarities as compared with wrought 316 SS, and the AM-related phenomenon that can potentially occur under neutron irradiation in nuclear reactors.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Complexity of deformation mechanism in neutron-irradiated 304L austenitic stainless steel at microstructural scale

The deformation mechanisms of neutron-irradiated 304 L stainless steel have been investigated using the in-situ electron backscattered diffraction (EBSD) technique. To decipher the role of irradiation, a detailed analysis was performed on irradiated miniature samples and compared with nonirradiated samples. Furthermore, at three levels of engineering strain, —0.0%, 4.8%, and 14.5%—microstructural features as well as EBSD were recorded at the identical location during in-situ deformation testing. Post-mortem analysis of the EBSD data revealed that the neutron-irradiated samples had higher fractions of the slip bands even at low amounts of deformation. Along with the slip bands, the neutron-irradiated sample showed the twins and martensitic phase formed almost parallel to the slip bands. In addition, the image results also indicated that the formation of twins and phases associated with the slip bands. A detailed mechanistic understanding has been investigated to identify the (111)γ planes orientation with respect to the loading direction associated with the formation of twins and martensite. The newly formed deformation twins and martensite were also found to maintain this relationship when they existed together.

304L austenitic stainless steel↗
DOE OSTI2021

Unearthing principal strengthening factors tuning the additive manufactured 15-5 PH stainless steel

Additive manufactured (AM) materials exhibit enhanced performance, while post-processing is essential to reinforce its properties. Controlling the tunable factors and the underlying strengthening mechanisms during the post-processing are a key to answering the calls from the industry and end users. We identified the principal strengthening factors that contribute to AM stainless steel under heat-treatment and weighed their importance. The as-built sample exhibited a unique microstructure with a heterogeneous grain size distribution, a small amount of retained austenite, high dislocation density, and dispersed oxide particles. The strengthening primarily by dislocation forest and additionally by heterogeneous grain size contributed to the as-built sample. Although aging slightly decreased dislocation strengthening, superior aging enhancement was achieved by Cu-precipitates. The solid-solutionizing not only increased the effective grain size but also reduced the dislocation density by eliminating the heterogeneous microstructure, which deteriorated the precipitation hardenability. Our findings shed light on the performance optimization of AM metals.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of the fatigue crack behavior of 304 stainless steels using synchrotron X-ray tomography and diffraction: Influence of the martensite fraction and role of inclusions

Here, the effect of fatigue on the microstructure of four-point bend specimens of three variations of 304 stainless steels (Commercial 304, 304H, and 304 L) was investigated using synchrotron x-ray tomography and diffraction. X-ray tomography revealed the formation of the fatigue-induced microvoids and crack while the diffraction data was used to quantify the amount of deformation-induced martensite found after fatigue in all samples. Transmission electron microscopy evidenced the role of the precipitates/inclusions on the microvoid formation. It was found to depend on their chemical nature. The shape of the precipitates/inclusions was also found to have an effect on the microvoid shape.

304 stainless steel↗
DOE OSTI2024

Microscopy modality transfer of steel microstructures: Inferring scanning electron micrographs from optical microscopy using generative AI

Scanning electron microscopy (SEM) is resource intensive, which limits its throughput in some applications. As an alternative, we propose applying computer vision and machine learning to generate high-quality synthetic SEM micrographs from micrographs obtained using light optical microscopy (LOM). Working with a correlated LOM/SEM dataset of dual-phase steel images, we test generative models of various architectures, including encoder-decoder networks, generative adversarial networks (GANs), and diffusion-based models. We find that the diffusion models significantly outperform other methods on both qualitative and quantitative assessments, while preserving key metallurgical meaning. This work establishes diffusion as the state-of-the-art for microscopy modality transfer and demonstrates the potential of AI-powered microscopy to enhance LOM with micron scale structural recreation.

Computer vision↗
DOE OSTI2023

Microstructure and crystallographic texture of high frequency electric resistance welded X65 pipeline steel

Here, microstructure and crystallographic texture and their correlation with impact toughness of high-frequency electric resistance welded (HF-ERW) X65 Grade pipeline steel have been investigated. X65 base metal after HF-ERW has formed a typical hourglass-shaped weld joint with four different regions, including the thermomechanical-affected zone (TMAZ), fine-grained heat affected zone (FGHAZ), coarse-grained heat affected zone (CGHAZ), and bondline (Weld Zone). X65 base metal shows prominent (113) [110] and (112) [110] texture components due to thermomechanical-controlled processing. TMAZ depicted random texture with a minor intensity of Cube component (001)[110] due to the partial recrystallization during welding. In the FGHAZ and CGHAZ, near the bondline, the base metal texture has been converted to rotated Goss (110) [110], Goss (110) [001], and rotated cube (001) [110] due to the recrystallization of the austenite and the shear deformation in the austenite temperature range. A high density of {100} and {110} cleavage planes is observed in the CGHAZ, which is often found to be the fracture location for the impact toughness testing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Austenite formation and cementite dissolution during intercritical annealing of a medium-manganese steel from a martensitic condition

In the present study, in situ high-energy X-ray diffraction (HEXRD), dilatometry, and metallography were conducted for the purpose of understanding microstructure evolution during intercritical annealing of a Fe-0.19C-4.39Mn steel from a martensitic initial condition. Three different simulations for austenite growth and solute partitioning during isothermal holding were conducted using the DICTRA™ module of Thermo-Calc®. The microstructures after intercritical annealing exhibit film-like retained austenite; however, in situ HEXRD indicates that retained austenite in the initial martensitic microstructure had decomposed upon heating to the isothermal holding temperature, suggesting that film-like austenite may be generated during intercritical annealing via nucleation and growth of new austenite and without necessarily preserving initial retained austenite films in the martensitic microstructure. Metallography and in situ HEXRD also indicate that cementite had formed upon heating but did not readily dissolve during an 1800 s isothermal hold although considerable growth of austenite had occurred during the isothermal hold, suggesting that austenite nucleation and initial growth during intercritical annealing does not solely occur due to carbon partitioning. A simulation incorporating cementite suggests that the increase in austenite fraction during intercritical annealing initially occurs in association with Mn partitioning followed by austenite growth induced by gradual cementite dissolution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase instabilities in austenitic steels during particle bombardment at high and low dose rates

Disruption of phase stability by energetic particle bombardment is a major challenge in designing advanced radiation-tolerant alloys and ion beam processing of nanocomposites. Particularly, ballistic dissolution susceptibility of different solute nanocluster species in alloys is poorly understood. Here, low dose rate neutron irradiations were conducted on a Fe-Cr-Ni based austenitic steel in the BOR-60 reactor (9.4 × 10 -7 dpa/s, 318 °C) followed by accelerated dose rate ion irradiations at multiple temperatures ( 10 -3 dpa/s, 380 – 420 °C). Using atom probe tomography, the stability of radiation-enhanced Cu-rich and radiation-induced Ni-Si-Mn-rich nanoclusters was evaluated. During neutron irradiation, Cu-rich clusters nucleated with their core concentrations progressively increasing with dose, while Ni-Si-Mn-rich clusters formed and evolved into G-phase precipitates. Ion irradiations dramatically altered the nanoclusters. Cu-rich clusters were ballistically dissolved, but Ni-Si-Mn-rich clusters remained stable and coarsened with dose at 400 and 420 °C, highlighting that different nanocluster species in a single microstructure can have innately distinct ballistic dissolution susceptibilities. Solute-specific recoil rates were incorporated into the Heinig precipitate stability model, which shows that in addition to radiation-enhanced diffusion, recovery from ballistic dissolution depends on solute concentration gradient near cluster interfaces. Finally, the combined experimental-modeling study quantified the critical temperatures and damage rates where ballistic dissolution dominates for each cluster species.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quantification of solution annealing effects on microstructure and property in a laser powder bed fusion 316H stainless steel

Solution annealing (SA) is an effective way to mitigate microstructural heterogeneity and to optimize mechanical performance of alloys manufactured by laser powder bed fusion (LPBF). In this study, a comprehensive and quantitative understanding of the recovery and recrystallization processes in the SA temperature range of LPBF 316H stainless steel is provided using results from analytical electron microscopy and in-situ high-energy synchrotron x-ray scattering. The profound effect of dislocation structures and secondary phase particles on mechanical performance, particularly under tension and creep conditions, is rationalized using deformation models that incorporate microstructural inputs. This study, for the first time, quantifies the broad effect of nano oxide inclusions on dislocation recovery kinetics, on grain growth and recrystallization kinetics, and on tension strength and creep resistance. The fundamental differences between the LPBF and the conventional wrought materials are revealed. The findings address critical questions in post-build processing of AM materials and pave the way for their rapid qualification for high temperature applications.

In-situ X-ray diffraction↗
DOE OSTI2026

Spatially resolved phase transformation mapping in 410 stainless steel during additive manufacturing visualized via real-time infrared data

Here, in this study, we demonstrate that spatially resolved cooling curves derived from real-time infrared (IR) thermography during additive manufacturing (AM) can capture spatial variations in phase transformation temperatures through cooling curve analysis (CCA). Using this approach, we show that during laser hot-wire deposition of 410 stainless steel (410SS), the martensite start temperature (M s ) evolves dynamically throughout the build. The M s temperature is spatially nonuniform, ranging from 185 °C to 348 °C, with the lowest values toward the build center and higher values toward the upper region of the deposit. In the lower portion of the build, no M s inflection is detected via CCA, consistent with transformation occurring earlier during thermal cycling followed by tempering during subsequent thermal cycles. These trends in M s are corroborated by characterizing the microstructure by electron backscatter diffraction (EBSD). Traditionally, M s is assumed to be constant, and a single interpass temperature is applied during both deposition and residual stress modeling. Our results demonstrate that IR-derived cooling curves provide a route to spatially and temporally resolved transformation temperature tracking for dynamic interpass control and improved residual-stress modeling.

Additive manufacturing↗
DOE OSTI2024

Microstructure manipulation via machining and heat treatments in hybrid manufacturing of 316L stainless steel

Hybrid manufacturing combines additive and subtractive (machining) processes in a single platform to reduce the total time to fabricate a component in its final form. Here we show that if sufficient plastic deformation can be imparted to the material during machining, recrystallization can be triggered during post-fabrication heat treatment. This can enable highly localized microstructure control. Additionally, we show that stainless steel 316L, when machined without coolant accumulates significant plastic strain compared to when machined with coolant that results in faster recrystallization kinetics during heat treatment. These effects are limited to the surface while the bulk microstructure remains unaffected.

316L stainless steel↗
DOE OSTI2020

Size effect in stainless steel thin wires under tension

Miniaturization of modern devices drives the exploration into how materials behave in small dimensions. However, the mechanical behaviors of micro-scale specimens under varied loading conditions are still challenging to characterize and predict. In this work, specimen size-dependent weakening effect was experimentally revealed in 316L stainless steel thin wires under tension with wire diameter decreasing from 200 μm down to 61 μm. The underlying mechanisms were primarily associated with surface grain softening and strain localization, which were largely dependent on the number of grains across wire diameter. Through an analog composite model with surface and interior grains that follows the Hall-Petch relation, the extent of surface grain softening was found to coincide with the flow stress reduction due to lack of boundary strengthening. Further using elasto-plastic self-consistent polycrystal modeling, the stress-strain behaviors of interior and surface grains were well described in analogy to those of bulk materials with similar-size grains and extremely large grains, respectively. Subsequently, the analog composite model well simulated the specimen size-dependent weakening effect under tension. This article provided more insights into the size effect exploration and proposed a practical model for describing size-dependent mechanical behaviors of small-scale materials to be applied to miniaturized devices.

316L stainless steel↗
DOE OSTI2020

High-throughput experimentation for microstructural design in additively manufactured 316L stainless steel

In the present study, a combination of high-throughput (HT) and low-throughput (LT) techniques was used to rapidly determine the processing window and generate processing maps for Selective Laser Melting (SLM) of 316L stainless steel. The HT method includes the fabrication of hundreds of hex nut-shaped specimens, each processed with a unique combination of laser power, scanning speed, and hatch spacing. An easily removable scaffolding permitted rapid sample extraction from the base plate, thus saving machining cost and time. Hardness and immersion density measurements were used for HT characterization to identify a processing window for maximum strength and density. Within the defined processing window, a low-throughput (LT) microstructural interrogation of specimens were performed. The microstructural analysis included quantification at various length scales (i.e., grains size and morphology, texture, primary dendrite arm spacing, and melt pool geometry analysis). Microstructure-based processing maps as a function of volumetric energy density were generated. The combination of HT and LT methods produced a predictive relationship between hardness and primary dendrite arm spacing using a Hall-Petch relationship. A model is proposed to explain the dependence of microstructure on the melt pool geometry. Here, the HT method can be applied for the microstructural design of SLM-fabricated components in other alloys.

316L stainless steel↗
DOE OSTI2021

Effects of low-temperature neutron irradiation on the microstructure and tensile properties of duplex 2304 stainless steel and its electron-beam welds

A lean duplex stainless steel material (2304-grade) in its base metal and electron beam (e-beam) welded conditions were studied microstructurally and mechanically as a function of irradiation conditions to evaluate its use as a structural material at low temperatures (60–100 °C). Neutron irradiation up to a fluence of 1.40 × 10 19 n/cm 2 (E > 0.1 MeV) or ~0.011 dpa decreased the total elongation of both base metal and e-beam welded samples. Overall, radiation hardening was observed in all the samples. The transversely cut irradiated samples showed some nonuniform quasi-cleavage and shearing in their fracture surfaces, indicating the variance of ductile nature of the two-phased (deformable austenite and harder ferrite) duplex structure. The e-beam welded samples also showed quasi-cleavage fracture, which is a characteristic of radiation-induced embrittlement. Furthermore, these observations of the e-beam welded samples were attributed to the formation of coarse ferrites, grain boundary and intragranular phases such as γ 2 and γ 3 , and minor impurity phases such as CrN and Cr 2 N in the weld pool and/or heat-affected zone of the samples. Radiation-induced elemental segregation was also identified in the post-irradiated base metal.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hot deformation behavior of an industrially cast large grained low density austenitic steel

Hot compression testing was performed on specimens of an Fe–30Mn–9Al–1Si-0.9C-0.5Mo wt.% low density steel which were extracted from an industrial casting with large grain size (320 ± 50 μm). Grain boundaries act as nucleation sites for dynamic recrystallization in the present material and the large grain size results in fewer nucleation sites, which delays dynamic recrystallization to larger strains and/or higher temperatures and causes higher rates of work hardening relative to similar materials but with smaller grain sizes. Here, a relatively high activation energy for hot deformation of 470 ± 90 kJ mol –1 was determined from a Zener-Hollomon analysis of the flow stresses at different temperatures and strain rates, attributed in part to the large grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of processing parameters and build orientation on microstructure and performance of AISI stainless steel 304L made with selective laser melting under different strain rates

Selective laser melting (SLM) process brings diverse potentials on geometry flexibility; therefore, it is more and more widespread to be employed in fabrication metal alloys served for industries. Nonetheless, a material characterization study is desired to carry on for better understanding the correlation among process, structure, microstructure, and performance. In the current study, the SLM fabricated AISI stainless steel 304L was fabricated with different process parameters and built orientations (horizontal, inclined, and vertical. The tensile behavior was evaluated under different strain rates (0.0001 /s, 0.001 /s, 0.01 /s, and 0.1 /s) and compared to the commercial cold-rolled and annealed counterpart. Grain structures, tensile strength, elongation-to-failure, strain rate sensitivity, work hardening, and fractographic analysis were evaluated in terms of the effect of energy density, build orientation, and strain rate. The output indicates the tensile strength increases with increasing strain rates. On the contrary, the elongation-to-failure shows a decreasing trend with strain rates. Tensile properties of specimens built in the horizontal and inclined orientations are more sensitive to strain rates due to the smaller dimension of grain structures. Tensile anisotropy depends on the energy input, where a high energy density could yield a strong build orientation-dependent anisotropy. Hall-Petch relationship is validated to explain the mechanical anisotropy in different built orientations for SLM alloys. The strain hardening exponent and work hardening rate are demonstrated to be positively correlated, and they increase with smaller grain sizes. The fine dimple features indicate the ductile fracture mode regardless of strain rates. The size of the ductile dimples seems to depend on the strain rates and build orientations.

36 MATERIALS SCIENCE↗