Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shell effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Deformation and Fracture Behaviors of Cylindrical Battery Shell During Thermal Runaway

Thermal runaway is one of the catastrophic failure modes of lithium-ion cells. During thermal runaway in cylindrical cells, sidewall shell rupture has been identified as a contributing factor for thermal runaway propagation in battery packs. Herein, the deformation and fracture behaviors of the battery shell during thermal runaway are investigated based on in-situ and ex-situ characterization as well as physics-based modeling. The deformation and fracture modes of the battery shell with/without Carbon Fiber Reinforced Polymer (CFRP) sleeves are identified. In the simulation, the strain introduced by thermal expansion of the system is considered, as well as the thermal and strain rate effects on the plastic stage. The final cell shell modeling is validated by cell thermal runaway tests. Results reveal the quantitative relation between shell deformation behaviors and the pressure and temperature distribution. Both the experiment and model demonstrate the effectiveness of adding a tight-fitting CFRP sleeve around the cell in limiting the side-wall rupture of the shell. The use of CFRP tubes introduces a novel phenomenon in the context of uneven temperature distribution. Results shed light on the mechanistic analysis of a cell side-wall rupture during thermal runaway and provide essential guidance for the next-generation safe battery design.

battery casing↗

Superparamagnetic behavior of heat treated Mg{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} ferrite nanoparticles studied by Mössbauer spectroscopy

Nanoparticles of Mg{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} ferrite have been synthesized by co-precipitation method. XRD and Mössbauer spectroscopic results of Mg{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} annealed at 200 °C, 500 °C and 800 °C are reported. It was observed that the crystallite size increases and the lattice parameter decreases with increase in annealing temperature. The observed decrease in lattice strain supports the increase in crystallite size. The Mössbauer spectra of the samples annealed at 200 °C and 500 °C exhibits superparamagnetic doublets whereas the Mössbauer spectrum of the sample annealed at 800 °C exhibits paramagnetic doublet along with weak sextet of hyperfine interaction. The values of isomer shift resemble the presence of high spin iron ions. The studied ferrite nanoparticles are suitable for biomedical applications. The results are incorporated employing core-shell model and cation redistribution.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Nuclear physics without high-momentum potentials: Constructing the nuclear effective interaction directly from scattering observables

The traditional approach to nuclear physics encodes phase shift information in a nucleon-nucleon (NN) potential, producing a nucleon-level interaction that captures the sub-GeV consequences of QCD. A further reduction to the nuclear scale is needed to produce an effective interaction for soft Hilbert spaces, such as those employed in the shell model. Here we describe an alternative construction of the effective interaction that is simple and quite precise, proceeding from the QCD scale directly to the nuclear scale. This eliminates the need for constructing and renormalizing the high-momentum NN potential. Instead, continuum phase shifts and mixing angles are used directly at the nuclear scale. The method exploits the analytic continuity in energy of HOBET (Harmonic-Oscillator-Based Effective Theory) to connect bound states to continuum solutions at specific energies. The procedure is systematic, cutoff independent, and convergent, yielding keV accuracy at NNLO or N 3 LO, depending on the channel. Lepage plots are provided.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Magnetic field directed assembly of superstructures of ferrite-ferroelectric core-shell nanoparticles and studies on magneto-electric interactions

Composites of ferromagnetic and ferroelectric are of interest for studies on mechanical strain mediated magneto-electric (ME) interactions and for useful technologies. Here, we report on magnetic-field-assisted-assembly of barium titanate (BTO)-nickel ferrite (NFO) core-shell particles into linear chains and 2D/3D arrays and measurements of ME effects in such assemblies. First, we synthesized the core-shell nano-particles with 50–600 nm BTO and 10–200 nm NFO by chemical self-assembly by coating the ferroic particles with complementary coupling groups and allowing them to self-assemble in the presence of a catalyst via the “click” reaction. The core-shell structure was confirmed with electron microscopy and scanning probe microscopy. We obtained superstructure of the core-shell particles by subjecting them to a magnetic field gradient that exerts an attractive force on the particles and align them toward the regions of high field strengths. At low particle concentration, linear chains were formed and they evolved into 2D and 3D arrays at high particle concentrations. Magnetoelectric characterization on unassembled films and assembled arrays has been performed through measurements of low-frequency ME voltage coefficient (MEVC) by subjecting the sample to a bias magnetic field and an ac magnetic field. The MEVC is higher for field-assembled samples than for unassembled films and is found to be sensitive to field orientation with a higher MEVC for magnetic fields parallel to the array direction than for magnetic fields perpendicular to the array. A maximum MEVC of 20 mV/cm Oe, one of the highest reported for any bulk nanocomposite, is measured across the array thickness. A model is provided for ME coupling in the superstructures of BTO-NFO particulate composites. First, we estimated the MEVC for a free-standing BTO-NFO core-shell particle and then extended the model to include an array of linear chains of the particles. The theoretical estimates are in qualitative agreement with the data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Anomalous photoconductive behavior of a single InAs nanowire photodetector

We report on a bare InAs nanowire photodetector which exhibits an anomalous photoconductive behavior. Under low-power illumination, the current is smaller than the dark current, and monotonously decreases as the excitation power increases. When the excitation power is high enough, the current starts to increase normally. The phenomenon is attributed to different electron mobilities in the “core” and “shell” of a relatively thick nanowire originating from the surface effect, which result in a quickly dropped “core current” and slowly increased “shell current” under illumination.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

HEAVY ION HEATING DUE TO INTERACTIONS WITH OUTWARD AND INWARD ALFVEN WAVE PACKETS

The study of simultaneous cyclotron interactions of heavy ions with outward- and inward-propagating Alfven wave packets in the solar wind was self-consistently conducted with wave-packet dynamics. It was shown that, even when the ratio of intensities of the Alfven waves propagating from the Sun and the inward propagating waves are rather large (a factor of 10 or more), the distribution function of the ions simultaneously interacting with both of the wave packets drastically differs from the distribution function formed by the interaction of ions with waves only propagating from the Sun. In the latter case, the ions acquire a shell-like distribution; in the former case, a new non-shell-type distribution with much larger effective temperatures is formed. The temporal dynamics of the ion-distribution function and the self-consistent modification of the wave-power spectral density for both the outward and inward waves were also investigated. The results refute claims by Isenberg and Hollweg that the outward-propagating waves generate the inward waves through the instability of their resonant particle shell distribution.

79 ASTRONOMY AND ASTROPHYSICS↗

SUPERGIANT SHELLS AND MOLECULAR CLOUD FORMATION IN THE LARGE MAGELLANIC CLOUD

We investigate the influence of large-scale stellar feedback on the formation of molecular clouds in the Large Magellanic Cloud (LMC). Examining the relationship between H I and {sup 12}CO(J = 1-0) in supergiant shells (SGSs), we find that the molecular fraction in the total volume occupied by SGSs is not enhanced with respect to the rest of the LMC disk. However, the majority of objects ({approx}70% by mass) are more molecular than their local surroundings, implying that the presence of a supergiant shell does on average have a positive effect on the molecular gas fraction. Averaged over the full SGS sample, our results suggest that {approx}12%-25% of the molecular mass in supergiant shell systems was formed as a direct result of the stellar feedback that created the shells. This corresponds to {approx}4%-11% of the total molecular mass of the galaxy. These figures are an approximate lower limit to the total contribution of stellar feedback to molecular cloud formation in the LMC, and constitute one of the first quantitative measurements of feedback-triggered molecular cloud formation in a galactic system.

79 ASTRONOMY AND ASTROPHYSICS↗

Radiative lifetimes of zincblende CdSe/CdS quantum dots

Recent synthetic advances have made available very monodisperse zincblende CdSe/CdS quantum dots having near-unity photoluminescence quantum yields. Because of the absence of nonradiative decay pathways, accurate values of the radiative lifetimes can be obtained from time-resolved PL measurements. Radiative lifetimes can also be obtained from the Einstein relations, using the static absorption spectra and the relative thermal populations in the angular momentum sublevels. We found that one of the inputs into these calculations is the shell thickness, and it is useful to be able to determine shell thickness from spectroscopic measurements. We use an empirically corrected effective mass model to produce a “map” of exciton wavelength as a function of core size and shell thickness. These calculations use an elastic continuum model and the known lattice and elastic constants to include the effect of lattice strain on the band gap energy. The map is in agreement with the known CdSe sizing curve and with the shell thicknesses of zincblende core/shell particles obtained from TEM images. Furthermore, if selenium–sulfur diffusion is included and lattice strain is omitted from the calculation then the resulting map is appropriate for wurtzite CdSe/CdS quantum dots synthesized at high temperatures, and this map is very similar to one previously reported (J. Am. Chem. Soc. 2009, 131, 14299). Radiative lifetimes determined from time-resolved measurements are compared to values obtained from the Einstein relations, and found to be in excellent agreement. For a specific core size (2.64 nm diameter, in the present case), radiative lifetimes are found to decrease with increasing shell thickness. Thus, this is similar to the size dependence of one-component CdSe quantum dots and in contrast to the size dependence in type-II quantum dots.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Overlap functions, spectroscopic factors, and asymptotic normalization coefficients generated by a shell-model source term

Overlap functions for one-nucleon removal are calculated as solutions of the inhomogeneous equation. The source term for this equation is generated by the 0(Planck constant/2pi)omega no-core shell-model wave functions and the effective nucleon-nucleon (NN) interactions that fit oscillator matrix elements derived from the NN scattering data. For the lightest A<=4 nuclei this method gives reasonable agreement with exact ab initio calculations. For 4<A<=16, this method gives a fair agreement between the calculated and measured asymptotic normalization coefficients. The spectroscopic factors obtained show systematic deviation from the corresponding shell-model values. This deviation correlates with nucleon separation energies and follows a similar trend seen in the reduction factor of the nucleon knockout cross sections. Comparison with the overlap functions and spectroscopic factors obtained in the variational Monte Carlo method is presented and discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Emergence of an island of extreme nuclear isomerism at high excitation near 208 Pb

Metastable states with $T_{1/2}$ = 8(2) ms in 205Bi and $T_{1/2}$ = 0.22(2) ms in 204 Pb, with ≈ 8 MeV excitation energy and angular momentum ≥ 22 $\hbar$, have been established. These represent, by up to two orders of magnitude, the longest-lived nuclear states above an excitation energy of 7 MeV, ever identified in the nuclear chart. Additionally, the half-life of the 10.17 MeV state in 206 Bi has been determined to be 0.027(2) ms, the next highest value in this highly excited regime. These observations indicate the emergence of an island of extreme nuclear isomerism arising from core-excited configurations at high excitation in the vicinity of the doubly closed-shell nucleus 208 Pb. These results are expected to provide discriminating tests of the effective interactions used in current large-scale shell-model calculations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Asymmetric-shell ignition capsule design to tune the low-mode asymmetry during the peak drive

The low-mode radiation flux asymmetry in the hohlraum is a main source of performance degradation in the National Ignition Facility (NIF) implosion experiments. To counteract the deleterious effects of the large positive P2 flux asymmetry during the peak drive, this paper develops a new tuning method called asymmetric-shell ignition capsule design which adopts the intentionally asymmetric CH ablator layer or deuterium-tritium (DT) ice layer. A series of two-dimensional implosion simulations have been performed, and the results show that the intentionally asymmetric DT ice layer can significantly improve the fuel ρR symmetry, hot spot shape, hot spot internal energy, and the final neutron yield compared to the spherical capsule. This indicates that the DT asymmetric-shell capsule design is an effective tuning method, while the CH ablator asymmetric-shell capsule could not correct the fuel ρR asymmetry, and it is not as effective as the DT asymmetric-shell capsule design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rotational band structure in Mg 32

There is significant evidence supporting the existence of deformed ground states within the neutron-rich N ≈ 20 neon, sodium, and magnesium isotopes that make up what is commonly called the “island of inversion.” However, the rotational band structures, which are a characteristic fingerprint of a rigid nonspherical shape, have yet to be observed. Here, in this work, we report on a measurement and analysis of the yrast (lowest lying) rotational band in 32 Mg up to spin I = 6 + produced in a two-step projectile fragmentation reaction and observed using the state-of-the-art γ-ray tracking detector array, GRETINA (γ-ray energy tracking in-beam nuclear array). Large-scale shell-model calculations using the SDPF-U-MIX effective interaction show excellent agreement with the new data. Finally, a theoretical analysis of the spectrum of rotational states as a function of the pairing gap, together with cranked-shell-model calculations, provides intriguing evidence for a reduction in pairing correlations with increased angular momentum, also in line with the shell-model results.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Flat plate puncture test convergence study.

The ASME Task Group on Computational Mechanics for Explicit Dynamics is investigating the types of finite element models needed to accurately solve various problems that occur frequently in cask design. One type of problem is the 1-meter impact onto a puncture spike. The work described in this paper considers this impact for a relatively thin-walled shell, represented as a flat plate. The effects of mesh refinement, friction coefficient, material models, and finite element code will be discussed. The actual punch, as defined in the transport regulations, is 15 cm in diameter with a corner radius of no more than 6 mm. The punch used in the initial part of this study has the same diameter, but has a corner radius of 25 mm. This more rounded punch was used to allow convergence of the solution with a coarser mesh. A future task will be to investigate the effect of having a punch with a smaller corner radius. The 25-cm thick type 304 stainless steel plate that represents the cask wall is 1 meter in diameter and has added mass on the edge to represent the remainder of the cask. The amount of added mass to use was calculated using Nelm's equation, an empirically derived relationship between weight, wall thickness, and ultimate strength that prevents punch through. The outer edge of the plate is restrained so that it can only move in the direction parallel to the axis of the punch. Results that are compared include the deflection at the edge of the plate, the deflection at the center of the plate, the plastic strains at radius r=50 cm and r=100 cm , and qualitatively, the distribution of plastic strains. The strains of interest are those on the surface of the plate, not the integration point strains. Because cask designers are using analyses of this type to determine if shell will puncture, a failure theory, including the effect of the tri-axial nature of the stress state, is also discussed. The results of this study will help to determine what constitutes an adequate finite element model for analyzing the puncture hypothetical accident.

36 MATERIALS SCIENCE↗

Resonant K α spectroscopy of solid-density aluminum plasmas

Here, the x-ray intensities made available by x-ray free electron lasers (FEL) open up new x-ray matter interaction channels not accessible with previous sources. We report here on the resonant generation of Kα emission, that is to say the production of copious Kα radiation by tuning the x-ray FEL pulse to photon energies below that of the K edge of a solid aluminum sample. The sequential absorption of multiple photons in the same atom during the 80 fs pulse, with photons creating L-shell holes and then one resonantly exciting a K-shell electron into one of these holes, opens up a channel for the Kα production, as well as the absorption of further photons. We demonstrate rich spectra of such channels, and investigate the emission produced by tuning the FEL energy to the K-L transitions of those highly charged ions that have transition energies below the K edge of the cold material. The spectra are sensitive to x-ray intensity dependent opacity effects, with ions containing L-shell holes readily reabsorbing the Kα radiation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Liquid immiscibility and core-shell morphology formation in ternary Al–Bi–Sn alloys

The effects of composition on liquid immiscibility, macroscopic morphology, microstructure and phase transformation in ternary Al–Bi–Sn alloys were investigated. Three types of morphology, the core-shell type, the stochastic droplet type and uniform dispersion type, of Al–Bi–Sn particles prepared by a jet breakup process were distinguished, and the relationships between which were discussed. The phase transformation behaviors of the Al–Bi–Sn alloys were studied by thermal analysis, in agreement with the microstructural observation and microanalysis. The liquid immiscibility and formation of the core-shell morphology in Al–Bi–Sn alloys are easily achieved when the composition lies in the liquid miscibility gap. The particles exhibit a high melting point Al-rich core with a low melting point Sn–Bi-rich solder shell, showing promise for application as high-density electronic packaging materials. - Highlights: • The liquid demixing, morphology and microstructure in Al–Bi–Sn alloys were studied. • Three types of morphology were classified and discussed. • The conditions for formation of the core-shell morphology were obtained. • The phase transition behaviors agree with the microstructure characterization. • The Al/Sn–Bi core-shell particles show promise for use in electronic packaging.

36 MATERIALS SCIENCE↗

Effects of ternary mixed crystal and size on optical phonons in wurtzite nitride core-shell nanowires

Within the framework of dielectric continuum and Loudon's uniaxial crystal models, existence conditions dependent on components and frequencies for optical phonons in wurtzite nitride core-shell nanowires (CSNWs) are discussed to obtain dispersion relations and electrostatic potentials of optical phonons in In{sub x}Ga{sub 1−x}N/GaN CSNWs. The results show that there may be four types of optical phonons in In{sub x}Ga{sub 1−x}N/GaN CSNWs for a given ternary mixed crystal (TMC) component due to the phonon dispersion anisotropy. This property is analogous to wurtzite planar heterojunctions. Among the optical phonons, there are two types of quasi-confined optical (QCO) phonons (named, respectively, as QCO-A and QCO-B), one type of interface (IF) phonons and propagating (PR) phonons existing in certain component and frequency domains while the dispersion relations and electrostatic potentials of same type of optical phonons vary with components. Furthermore, the size effect on optical phonons in CSNWs is also discussed. The dispersion relations of IF and QCO-A are independent of the boundary location of CSNWs. Meanwhile, dispersion relations and electrostatic potentials of QCO-B and PR phonons vary obviously with size, especially, when the ratio of a core radius to a shell radius is small, and dispersion relation curves of PR phonons appear to be close to each other, whereas, this phenomenon disappears when the ratio becomes large. Based on our conclusions, one can further discuss photoelectric properties in nitride CSNWs consisting of TMCs associated with optical phonons.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ionization competition effects on population distribution and radiative opacity of mixture plasmas

Ionization competition arising from the electronic shell structures of various atomic species in the mixture plasmas was investigated, taking SiO{sub 2} as an example. Using a detailed-level-accounting approximation, we studied the competition effects on the charge state population distribution and spectrally resolved and Planck and Rosseland mean radiative opacities of mixture plasmas. A set of coupled equations for ionization equilibria that include all components of the mixture plasmas are solved to determine the population distributions. For a given plasma density, competition effects are found at three distinct temperature ranges, corresponding to the ionization of M-, L-, and K-shell electrons of Si. Taking the effects into account, the spectrally resolved and Planck and Rosseland mean opacities are systematically investigated over a wide range of plasma densities and temperatures. For a given mass density, the Rosseland mean decreases monotonically with plasma temperature, whereas Planck mean does not. Although the overall trend is a decrease, the Planck mean increases over a finite intermediate temperature regime. A comparison with the available experimental and theoretical results is made.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗