Search NASA⌕ Search

SEARCH · Search NASA

Results for “SiO2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Influence of Ag metal dispersion on the thermal conversion of ethanol to butadiene over Ag-ZrO 2 /SiO 2 catalysts

Atomistic scale models were developed and coupled with experimental investigation to deliver a functional understanding of catalytic activity and selectivity in the conversion of ethanol to 1,3-butadiene over Ag/ZrO 2 /SiO 2 . A detailed evaluation of the structural and electronic properties of the resultant catalyst models led to the identification of critical active sites of the catalyst. More importantly, the extent of Ag dispersion on the SiO 2 support and relative proximity to ZrO 2 were found to vary with the oxidation state of Ag and local coordination environment (Ag-O SiO2 ) allowing for critical control of ethanol conversion towards butadiene or ethylene. Simulations revealed that less dispersed or clustered Ag contain predominantly Ag 0 charge state and promote conversion of ethanol to ethylene. The well-dispersed Ag/ZrO 2 /SiO 2 catalyst instead contain a larger fraction of cationic Ag δ+ , and predominantly promote ethanol dehydrogenation and subsequent production of butadiene. The theoretical insights drawn were validated and confirmed experimentally using TEM, XRD and reactivity measurements demonstrating the effect of Ag dispersion on the selectivity of ethanol conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electronic impact of Ni2P nanoparticle size on hydrogenation rates

Nickle phosphide, Ni2P, nanoparticles supported on SiO2 show a marked volcano shaped size dependence. Kinetic analysis and physicochemical characterization shows the electron density of Ni to increase with increasing Ni2P size, enhancing in turn the H2 adsorption strength. For particles below 15 nm, H adsorbs weakly causing a low surface coverage of H, gradually increasing with particle size. For large particles, hydrogen binds too strongly causing a high coverage but low catalytic activity. The remarkable size dependence of the electronic properties show that Ni2P particle size can be used to fine-tune its activity for hydrogenation.

Ni2P size effect, Electron density, H2 adsorption ↗

Effects of Water Vapor on the Reactivity of Aluminosilicates in Vapor-Phase Propanal Aldol Condensation

Aluminosilicate materials have been extensively studied as efficient aldol catalysts for C-C coupling reactions due to their acidic nature, high surface area, thermal stability, and porous structure. This work investigated the impact of water vapor pressure on the catalytic reactivity of aluminosilicates for the aldol condensation of propanal to 2-methyl-2-pentenal (MP). The catalytic performance of amorphous SiO2-Al2O3 (A-Si-Al) and aluminated MCM-41 (Al-MCM-41) for the vapor-phase aldol condensation of propanal was evaluated at 200 degrees C as a function of vapor-phase water content at atmospheric pressure. Our findings demonstrate that co-feeding low water vapor pressures (1-18 kPa) with propanal enhances the rates of MP production at 200 degrees C on A-Si-Al. Conversely, water vapor pressures of 25 kPa result in a decrease in aldol dimer formation rates. The rate of MP production evaluated on Al-MCM-41 also increased in the presence of 5 kPa water compared to anhydrous conditions. Propylamine temperature-programmed desorption analyses revealed an increase in Bronsted acid site density when both catalysts were exposed to water, which likely accounts for the observed enhancement in aldol condensation reactivity under hydrous conditions. Reversibility testing of the water vapor effect under reaction conditions, combined with X-ray diffraction analysis of fresh, spent, and regenerated catalysts, revealed no structural changes in either aluminosilicate upon exposure to water or reaction conditions. The rates of aldol condensation and the impact of water vapor were highly consistent across both materials, suggesting that zeolite crystallinity has minimal influence on the catalytic performance.

acid catalysts↗

Protonation enthalpies of metal oxides from high temperature electrophoresis

Surface protonation reactions play an important role in the behavior of mineral and colloidal systems, specifically in hydrothermal aqueous environments. However, studies addressing the reactions at the solid/liquid interface at temperatures above 100 C are scarce. In this study, newly and previously obtained high temperature electrophoresis data (up to 260 C) zeta potentials and isoelectric points for metal oxides, including SiO2, SnO2, ZrO2, TiO2, and Fe3O4, were used in thermodynamic analysis to derive the standard enthalpies of their surface protonation. Two different approaches were used for calculating the protonation enthalpy: one is based on thermodynamic description of the 1-pKa model for surface protonation, and another one on a combination of crystal chemistry and solvation theories which link the relative permittivity of the solid phase and the ratio of the Pauling bond strength and bond length to standard protonation enthalpy. From this analysis, two expressions relating the protonation enthalpy to the relative permittivity of the solid phase were obtained.

36 MATERIALS SCIENCE↗

Effect of chemical and physical heterogeneities on colloid-facilitated cesium transport

A set of column experiments was conducted to investigate the chemical and physical heterogeneity effect on colloid facilitated transport under slow pore velocity conditions. Pore velocities were kept below 100 cm d-1 for all experiments. Glass beads were packed into columns establishing four different conditions: 1) homogeneous, 2) mixed physical heterogeneity, 3) sequentially layered physical heterogeneity, and 4) chemical heterogeneity. The homogeneous column was packed with glass beads (diameter 500-600 µm), and physical heterogeneities were created by sequential layering or mixing two sizes of glass bead (500-600 µm and 300-400 µm). A chemical heterogeneity was created using 25% of the glass beads coated with hydrophobic molecules (1H-1H-2H-2H-perfluorooctyltrichlorosilane) mixed with 75% pristine glass beads (all 500-600 µm). Input solution with 0.5 mM CsI and 50 mg L-1 colloids (1-µm diameter SiO2) was pulsed into columns under saturated conditions. The physical heterogeneity in the packed glass beads retarded the transport of colloids compared to homogeneous (R = 25.0), but showed only slight differences between sequentially layered (R = 60.7) and mixed heterogeneity(R = 62.4). The column with the chemical, hydrophobic/hydrophilic, heterogeneity removed most of the colloids from the input solution. All column conditions stripped Cs from colloids onto the column matrix of packed glass beads.

Colloid-facilitated transport, cesium, physical he↗

Viscosity of many-component glasses

The effect of composition on the viscosity of multicomponent glasses was expressed as a function of temperature and composition for three composition regions containing various subsets of Al2O3, B2O3, Bi2O3, CaO, Cr2O3, F, Fe2O3, K2O, Li2O, MgO, MnO, Na2O, NiO, P2O5, SiO2, UO2, and ZrO2. Limits of applicability of the composition models are discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Deep-UV Raman spectroscopic analysis of structure and dissolution rates of silica-rich sodium borosilicate glasses

As part of ongoing studies to evaluate the relationships between structural variations in silicate glasses and rates of glass dissolution in aqueous media, molecular structures present in sodium borosilicate glasses of composition Na2O.xB2O3.(3-x)SiO2, with x 1 (Na2O/B2O3 ratio 1), were analyzed using deep-UV Raman spectroscopy. The results were quantified in terms of the fraction of SiO4 tetrahedra with one non-bridging oxygen (Q3) and then correlated with Na2O and B2O3 content. Increasing Na2O was found to raise the fraction of Q3 units in the glasses systematically, in agreement with studies on related glasses, and, as long as the value of x was not too high, contribute to higher rates of dissolution in single pass flow-through testing. The finding was obtained across more than one series of silica-rich glasses prepared for independent dissolution studies. In contrast, dissolution rates were less strongly determined by the Q3 fraction when the value of x was near unity and appeared to grow larger upon further reduction of the Q3 fraction. The results were interpreted to indicate the increasingly important role of network hydrolysis in the glass dissolution mechanism as the BO4 tetrahedron replaces the Q3 unit as the charge-compensating structure for Na+ ions. Finally, the use of deep-UV Raman spectroscopy was found to be advantageous in studying finely powdered glasses in cases where visible Raman spectroscopy suffered from weak Raman scattering and fluorescence interference.

36 MATERIALS SCIENCE↗

Structural analysis of some sodium and alumina rich high-level nuclear waste glasses

Sodium and aluminum rich high level nuclear waste glasses are prone to nepheline (NaAlSiO4) crystallization. Since nepheline removes three moles of glass forming oxides (Al2O3 and SiO2) per each mole of Na2O, its formation can result in sever deterioration of the chemical durability. The present study aims at investigating the relationships between the molecular-level structure of sodium alumino-borosilicate based simulated high-level nuclear waste glasses and their crystallization behavior by infrared spectroscopy (FTIR) and x-ray diffraction, respectively. The molecular structure of most of the investigated glasses comprises of a mixture of Q2 and Q3 (Si) units while aluminum and boron are predominantly present in tetrahedral and trigonal coordination, respectively. The increasing boron content has been shown to suppress the nepheline formation in the glasses. The structural influence of various glass components on nepheline crystallization has been discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Monte Carlo Simulations of the Corrosion of Aluminoborosilicate Glasses

Aluminum is one of the most common components included in nuclear waste glasses. Therefore, Monte Carlo (MC) simulations were carried out to investigate the influence of aluminum on the rate and mechanism of dissolution of sodium borosilicate glasses in static conditions. The glasses studied were in the compositional range (70-2x)% SiO2 x% Al2O3 15% B2O3 (15+x)% Na2O, where 0 ≤ x ≤ 15%. The simulation results show that increasing amounts of aluminum in the pristine glasses slow down the initial rate of dissolution as determined from the rate of boron release. However, the extent of corrosion - as measured by the total amount of boron release - initially increases with addition of Al2O3, up to 5 Al2O3 mol%, but subsequently decreases with further Al2O3 addition. The MC simulations reveal that this behavior is due to the interplay between two opposing mechanisms: (1) aluminum slows down the kinetics of hydrolysis/condensation reactions that drive the reorganization of the glass surface and eventual formation of a blocking layer; and (2) aluminum strengthens the glass thereby increasing the lifetime of the upper part of its surface and allowing for more rapid formation of a blocking layer. Additional MC simulations were performed whereby a process representing the formation of a secondary aluminosilicate phase was included. Secondary phase formation draws dissolved glass components out of the aqueous solution, thereby diminishing the rate of condensation and delaying the formation of a blocking layer. As a result, the extent of corrosion is found to increase continuously with increasing Al2O3 content, as observed experimentally. For Al2O3 < 10 mol%, the MC simulations also indicate that, because the secondary phase solubility eventually controls the aluminum content in the part of the altered layer in contact with the bulk aqueous solution, the dissolved aluminum and silicon concentrations at steady state are not dependent on the Al2O3 content of the pristine aluminoborosilicate glass.

Environmental Molecular Sciences Laboratory↗

Monte Carlo Simulations of Coupled Diffusion and Surface Reactions during the Aqueous Corrosion of Borosilicate Glasses

Borosilicate nuclear waste glasses develop complex altered layers as a result of coupled processes such as hydrolysis of network species, condensation of Si species, and diffusion. However, diffusion has often been overlooked in Monte Carlo models of the aqueous corrosion of borosilicate glasses. Therefore, three different models for dissolved Si diffusion in the altered layer were implemented in a Monte Carlo model and evaluated for glasses in the compositional range (75-x) mol% SiO2 (12.5+x/2) mol% B2O3 and (12.5+x/2) mol% Na2O, where 0 ≤ x ≤ 20%, and corroded in static conditions at a surface-to-volume ratio of 1000 m-1. The three models considered instantaneous homogenization (M1), linear concentration gradients (M2), and concentration profiles determined by solving Fick’s 2nd law using a finite difference method (M3). Model M3 revealed that concentration profiles in the altered layer are not linear and show changes in shape and magnitude as corrosion progresses, unlike those assumed in model M2. Furthermore, model M3 showed that, for borosilicate glasses with a high forward dissolution rate compared to the diffusion rate, the gradual polymerization and densification of the altered layer is significantly delayed compared to models M1 and M2. Models M1 and M2 were found to be appropriate models only for glasses with high release rates such as simple borosilicate glasses with low ZrO2 content.

borosilicates↗

Liquidus temperature in the spinel primary phase field: A comparison between optical and crystal fraction methods

Liquidus temperature (TL) was measured for simulated high-level waste borosilicate glasses covering a Hanford composition region, using an optical method and a crystal-fraction extrapolation method with X-ray diffraction data from isothermal heat treatments. The 38 glasses encompassed a one-component-at-a-time variation of a 16-component matrix. The TL values ranged from 1006°C to 1603°C. First-order polynomial models were fitted to data to obtain coefficients in terms of the effect of 1 mass% component addition on the TL: TL-increasing oxides Cr2O3 (264°C), “Others” (minor components, 163°C), oxides of noble metals (137°C), NiO (91°C), Al2O3 and Fe2O3 (~19–21°C); TL-decreasing oxides K2O (-26°C), Na2O (-41°C), and Li2O (-68°C); oxides of little effect MnO, P2O5, ZrO2, F, Bi2O3, SiO2, B2O3, and CaO (9 to -12°C). Also presented are temperatures (T1%) at which glasses contain 1 vol% of spinel as these values are considered relevant to the Hanford Tank Waste Treatment and Immobilization Plant. The measured and estimated values are compared and contrasted and the effect of TL and T1% on glass formulation is discussed.

crystal fraction↗

Evaluation of sintering effects on SiC incorporated UO2 kernels under Ar and Ar-4%H2 environments

Silicon carbide (SiC) is suggested as an oxygen getter in UO2 kernels used for TRISO particle fuels to lower oxygen potential and prevent kernel migration during irradiation. Scanning electron microscopy and X-ray diffractometry analyses performed on sintered kernels verified that internal gelation process can be used to incorporate SiC in urania fuel kernels. Sintering in either Ar or Ar-4%H2 at 1500 C lowered the SiC content in the UO2 kernels to some extent. Formation of UC was observed as the major chemical phase in the process, while other minor phases such as U3Si2C2, USi2, U3Si2, and UC2 were also identified. UC formation was presumed to be occurred by two reactions. The first was the SiC reaction with its protective SiO2 oxide layer on SiC grains to produce volatile SiO and free carbon that subsequently reacted with UO2 to form UC. The second process was direct UO2 reaction with SiC grains to form SiO, CO, and UC, especially in Ar-4%H2. A slightly higher density and UC content was observed in the sample sintered in Ar-4%H2, but the use of both atmospheres produced kernels with ~95% of theoretical density. It is suggested that incorporating CO in the sintering gas would prevent UC formation and preserve the initial SiC content.

Silicon carbide uranium oxide↗

Glass binder development for a glass-bonded sodalite ceramic waste form

This paper discusses work to develop Na2O-B2O3-SiO2 glass binders for immobilizing LiCl-KCl eutectic salt waste in a glass-bonded sodalite waste form following electrochemical reprocessing of used metallic nuclear fuel. Here, five new glasses with high Na2O contents were designed to generate waste forms having higher sodalite contents and fewer stress fractures. The structural, mechanical, and thermal properties of the new glasses were measured using variety of analytical techniques. The glasses were then used to produce ceramic waste forms with surrogate salt waste. The materials made using the glasses developed during this study were formulated to generate more sodalite than materials made with previous baseline glasses used. The coefficients of thermal expansion for the glass phase in the glass-bonded sodalite waste forms made with the new binder glasses were closer to the sodalite phase in the critical temperature region near and below the glass transition temperature. These improvements should result in lower probability of cracking in the full-scale monolithic ceramic waste form, leading to better long-term chemical durability. Additionally, a model generated during this study for predicting softening temperature of silicate binder glasses is presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Glass-bonded ceramic waste forms for immobilization of radioiodine from caustic scrubber wastes

Glass-bonded sodalite composite waste forms have been developed for the immobilization of liquid radioactive wastes resulting from off-gas treatment during aqueous reprocessing of used nuclear fuel, with a particular focus on 129I. The proposed composite waste form is comprised of aluminosilicate ceramic phases containing volatile radionuclides bonded with a glassy matrix. In this work, a suite of ten candidate low-temperature glass binders (ZnO-Bi2O3-based glasses and a Na2O-B2O3-SiO2 glass) were examined. Six glasses were mixed with caustic scrubber waste simulant previously converted into a sodalite-rich material (to provide glass fractions of 10 and 20 wt.%), uniaxially pressed into pellets, and sintered at 350 °C or 550 °C for 8 h in air. Iodine retention after heat treatment was assessed by neutron activation analysis, showing retention of 67-100 % of expected iodine. The aqueous durabilities of the resulting materials were then determined, following the ASTM C1308 standard test, showing iodine releases of 1 to 23 g m-2 after 4 d. The cumulative iodine release for the best performing system (a zinc-bismuth-borate glass binder) was <1 g m-2, and its iodine retention from processing was 67 %. The iodine releases compared favorably with other waste forms. In parallel, this best-performing composition was also consolidated via hot isostatic pressing (HIP) in a stainless-steel canister at 550 °C for 2 h under 100 MPa pressure. The HIPed sample was produced at the ~20 g scale and showed improved densification and minimal reaction with the canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗