Energy addition methods for hyper-velocity true flight simulation
Arc heating and magnetohydrodynamic acceleration energy addition methods for wind tunnel hypervelocity flow true flight simulation
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Arc heating and magnetohydrodynamic acceleration energy addition methods for wind tunnel hypervelocity flow true flight simulation
This paper studies the simulated performance of the Deep Space Optical Communication (DSOC) laser downlink pointing control system that has a pointing requirement at the sub-microradian scale. To achieve the required pointing precision, the DSOC Flight Laser Transceiver (FLT) point-ahead mirror (PAM) employs piezoelectric actuators, which are widely used in precision applications due to their high motion resolution, rapid response, and high output forces. However, a piezoelectric actuator's performance is often limited by nonlinearities in their response, most significantly hysteresis. To study the effect of hysteresis on our simulated pointing performance, an invertible hysteresis model is developed using the Classical Prantdl-Ishlinskii (CPI) method. The simulation includes models of DSOC hardware and electronic system components based on key parameters (bias, frequency response, noise), with the hysteresis modeled in the PAM piezo actuator dynamics. A Proportional-Integral controller provides feedback with measurements from two potential sources: strain gauge sensors or a photon-counting camera. To compensate for hysteresis behavior, a feedforward inverse CPI hysteresis model is implemented in the control system. Two CPI models are built using different sampling methods (uniform sampling and cosine spacing) and controller performance is compared. For the maximum command range of ±400 μrad at 1 mHz, results show that the feedforward combined with feedback control reduces output tracking error by 50% or 58% (to 0.20 or 0.38 μrad) compared to feedback control alone (from 0.40 or 0.90 μrad), corresponding to the uniform-sampled and cosine-sampled CPI models, respectively.
Aerodynamic design is an iterative process involving geometry manipulation and complex computational analysis subject to physical constraints and aerodynamic objectives. A design cycle consists of first establishing the performance of a baseline design, which is usually created with low-fidelity engineering tools, and then progressively optimizing the design to maximize its performance. Optimization techniques have evolved from relying exclusively on designer intuition and insight in traditional trial and error methods, to sophisticated local and global search methods. Recent attempts at automating the search through a large design space with formal optimization methods include both database driven and direct evaluation schemes. Databases are being used in conjunction with surrogate and neural network models as a basis on which to run optimization algorithms. Optimization algorithms are also being driven by the direct evaluation of objectives and constraints using high-fidelity simulations. Surrogate methods use data points obtained from simulations, and possibly gradients evaluated at the data points, to create mathematical approximations of a database. Neural network models work in a similar fashion, using a number of high-fidelity database calculations as training iterations to create a database model. Optimal designs are obtained by coupling an optimization algorithm to the database model. Evaluation of the current best design then gives either a new local optima and/or increases the fidelity of the approximation model for the next iteration. Surrogate methods have also been developed that iterate on the selection of data points to decrease the uncertainty of the approximation model prior to searching for an optimal design. The database approximation models for each of these cases, however, become computationally expensive with increase in dimensionality. Thus the method of using optimization algorithms to search a database model becomes problematic as the number of design variables is increased.
Heat transfer is best understood through theory and application of principles in thermal analysis. Modern thermal analysis leverages the power of computers and numerical methods to simulate heat transfer in networks representing a physical system. This lesson is an introduction to numerical methods in heat transfer.
Real-time detection and control of the isolator shock-train leading edge (STLE) is important to the performance of high-speed air-breathing engines, such as dual-mode scramjets. Typically, the STLE location is determined using wall static-pressure measurements, but there are often restrictions on the placement and overall number of the pressure transducers, reducing the viability and accuracy of such approaches. To address these issues, we introduce the adaptive pressure profile (APP) method for estimating the STLE location. This method does not require extensive prior characterization of the isolator or engine model. Instead, it uses real-time pressure measurements from a small number of transducers to adaptively learn the isolator pressure profile and subsequently uses this deduced profile to estimate the STLE location in a data-driven manner. The APP method works well in situations with sparse transducer placement. It produces accurate estimates when the STLE location is 1) not bounded by two or more transducers or 2) between two transducers that are several isolator duct heights apart. We demonstrate the efficacy of the APP method using simulations and experimental data from direct-connect isolator models. This validation shows that the APP method is accurate and robust for different flow regimes, transducer configurations, and model geometries.
Long-duration space exploration missions and sustained lunar or Martian surface operations present greater demands for multifunctional and reusable materials. By scaling down the amount of material to be launched from Earth, both mission cost and risk can be reduced. In this regard, leveraging in-space manufacturing capabilities with reusable feedstock materials is an attractive option, as it will allow for articles to be generated on demand, utilized, and then recycled for additional use. NASA’s Enabling Sustained Presence Using Recyclables (ESPUR) project aims to develop reusable materials using polymer-coated microparticles that are bonded via reversible Diels-Alder reactions, where only modest heat is needed to trigger the reverse reaction and enable reuse. For proof-of-concept demonstration, research is currently focused on the fabrication of epoxy microparticles that contain a copoly(carbonate urethane) coating with maleimide and furan functionalities. Here, we discuss the integration of computational materials modeling approaches to help navigate the large design space in this development effort. We perform molecular dynamics (MD) simulations with atomistic and coarse-grained models of the copolymer, which allow us to evaluate the effects of design parameters like the molecular weight and composition on the molecular interactions and chain dynamics. We show how the properties change with the reversible bonds. We also leverage discrete element method (DEM) simulations to assess how microparticle design parameters like the size ratio and volume fraction can be tuned to increase the packing density and number of microparticle contacts to improve the mechanical properties. Our results demonstrate how computational tools can be used in close collaboration with experimental efforts to accelerate material design.
A quick-look method has been developed for estimating convective heat flux due to plume impingement in the transition flow regime on a concave surface surrounding a rocket nozzle. Comparison with the flowfield and heat fluxes computed by the Monte Carlo Direct Simulation Method show the quick-look method to be conservative. Assumptions regarding the nature of the flowfield based on engineering judgment were shown to be essentially valid. Further, the assumption of free molecular impingement was shown to be non-conservative for portions of the surface. Potential refinements of the quick-look method are discussed.
This paper presents a numerical method to simulate the mixing of heavier LNG sprayed on lighter layer. Numerical results for evolutions of flow field and density field are obtained in a rectangular computational domain which includes the vicinity of the liquid surface. At the surface boundary, uniform distributions of the fluid velocity and the density are assumed. Detail structure of flow caused by impingements of liquid drops are neglected. But, to trigger a realistic motion, a series of random numbers is employed. It is used as an initial distribution of the density near the surface. This method successfully gives a realistic simulation of the mixing process. Numerical results for mixing velocity shows good agreement with experimental data.
A phase 2 research and development effort was conducted in area transonic, compressible, inviscid flows with an ultimate goal of numerically modeling complex flows inherent in advanced helicopter blade designs. The algorithms and methodologies therefore are classified as adaptive methods, which are error estimation techniques for approximating the local numerical error, and automatically refine or unrefine the mesh so as to deliver a given level of accuracy. The result is a scheme which attempts to produce the best possible results with the least number of grid points, degrees of freedom, and operations. These types of schemes automatically locate and resolve shocks, shear layers, and other flow details to an accuracy level specified by the user of the code. The phase 1 work involved a feasibility study of h-adaptive methods for steady viscous flows, with emphasis on accurate simulation of vortex initiation, migration, and interaction. Phase 2 effort focused on extending these algorithms and methodologies to a three-dimensional topology.
A method is described for testing silicon solar cells in concentrated sunlight and simulated sunlight. Concentrated sunlight is obtained by using an acrylic Fresnel lens; the simulated sunlight source is a short arc Xenon lamp. Average illumination levels during the tests are inferred from an assumed linear relationship between short circuit current and illumination. The linearity assumption is investigated for 0.3 alpha cm base resistivity silicon cells and found to be valid. Some typical results are presented to illustrate the type of information obtained during the testing.
When performing satellite remote sensing of the earth in the solar spectrum, atmospheric scattering and absorption effects provide the sensors corrupted information about the target's radiance characteristics. We are faced with the problem of reconstructing the signal that was reflected from the target, from the data sensed by the remote sensing instrument. This article presents a method for simulating radiance characteristic curves of satellite images using a MODTRAN 3.5 band model (BM) code to solve the radiative transfer equation (RTE), and proposes a method for the implementation of an adaptive system for automated atmospheric corrections. The simulation procedure is carried out as follows: (1) for each satellite digital image a radiance characteristic curve is obtained by performing a digital number (DN) to radiance conversion, (2) using MODTRAN 3.5 a simulation of the images characteristic curves is generated, (3) the output of the code is processed to generate radiance characteristic curves for the simulated cases. The simulation algorithm was used to simulate Landsat Thematic Mapper (TM) images for two types of locations: the ocean surface, and a forest surface. The simulation procedure was validated by computing the error between the empirical and simulated radiance curves. While results in the visible region of the spectrum where not very accurate, those for the infrared region of the spectrum were encouraging. This information can be used for correction of the atmospheric effects. For the simulation over ocean, the lowest error produced in this region was of the order of 105 and up to 14 times smaller than errors in the visible region. For the same spectral region on the forest case, the lowest error produced was of the order of 10-4, and up to 41 times smaller than errors in the visible region,
Lattice Boltzmann (LB) and hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) methods within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are applied to NASA's Revolutionary Computational Aerosciences (RCA) standard test cases for separated flows. A detailed comparison between the performance and accuracy of the two emerging numerical methodologies for turbulence resolving simulations, i.e. the LB and hybrid RANS/LES methods will be presented. This contribution addresses the RCA technical challenge to identify and down-select critical turbulence, transition, and numerical method technologies for 40% reduction in predictive error for standard turbulence separated flow test cases. Results for the 2D NASA wall-mounted hump and the axisymmetric transonic bump including time-averaged pressure coefficient, skin friction, and velocity pro les, as well as resolved and modeled Reynolds stresses for both numerical approaches will be presented and differences between LB and hybrid RANS/LES will be discussed.
The Nuclear Thermal Rocket Element Environmental Simulator (NTREES) facility at NASA’s Marshall Space Flight Center (MSFC) subjects materials and components typically found on nuclear thermal propulsion (NTP) systems to non-nuclear simulations of prototypic NTP reactor thermohydraulic environments. With 1.2 MW of inductive power available, the currently employed methods to simulate nuclear heating in NTREES consist of 1) inductively heating a test specimen, which typically cannot be performed on ceramic materials, or 2) heating gas that envelops the test specimen. The latter of these has provided a basis for developing so-called “immersion rigs” to be used in NTREES. Furthermore, immersion rigs are especially useful in the case of smaller, technically challenging test specimens. One such device, the “NTREES-5 Hydrogen Heat Exchanger” (N5HHX-01), designed and deployed to test small material coupons to ~0.5 g/s of 2800 K, 500 psi Hydrogen, is discussed herein. To achieve this desired delivery temperature level, the most suitable material for the N5HHX’s construction was pure tungsten, which imposed budgetary and manufacturing challenges. Also discussed in this paper is the design of the N5HHX rig’s sample container, which became the first iteration of improving NTREES small material coupon test operations by permitting rapid changeout of different material samples.
The fuel-to-dry-mass ratio of spacecraft continues to grow as new human spaceflight missions target destinations farther from Earth. Large amounts of liquid propellant can lead to significant coupling between the rigid-body dynamics of the spacecraft and the motion of the fuel within its storage tank. The present work gives an overview of the dynamic features and a flowchart for a method of simulating the motion of a spacecraft with fuel slosh inside a cylindrical, domed tank in a low-g environment. The method involves modeling the liquid propellant as a particle that transfers momentum to the spacecraft through perfectly inelastic collisions with the tank wall. The foundation of the modeling methodology is the approach taken during the Apollo program used to predict the effect of fuel slosh on the complex motion exhibited by the Service Module following separation from the Command Module. This paper discusses the motivation, methodology, and conclusions from the Apollo-era method, then presents corrections to the derivation of the dynamics and fills in the gaps left from the unavailability of the detailed contractor report and simulation code. The results presented in this paper provide an example that demonstrates the effect that fuel slosh can have on the trajectory of a spacecraft in a low-g environment.
The fuel-to-dry-mass ratio of spacecraft continues to grow as new human spaceflight missions target destinations from Earth. Large amounts of liquid propellant can lead to significant coupling between the rigid-body dynamics of the spacecraft and the motion of the fuel within its storage tank. The present work gives an overview of the dynamic features and a flowchart for a method of simulating the motion of a spacecraft with fuel slosh inside a cylindrical, domed tank in a low-g environment. The method involves modeling the liquid propellant as a particle that transfers momentum to the spacecraft through perfectly inelastic collisions with the tank wall. The foundation of the modeling methodology is the approach taken during the Apollo program used to predict the effect of fuel slosh on the complex motion exhibited by the Service Module following separation from the Crew Module. This paper discusses the motivation, methodology, and conclusions from the Apollo-era method, and subsequently builds upon it by incorporating corrections to the derivation of the dynamics and filling in the gaps due to unavailability of the detailed contractor report and simulation code. The results presented in this paper provide an example that demonstrates the effect that fuel slosh can have on the trajectory of a spacecraft in a low-g environment.
Contamination of spacecraft components with planetary and foreign object debris is a growing concern. Face seals separating the spacecraft cabin from the debris filled environment are particularly susceptible; if the seal becomes contaminated there is potential for decreased performance, mission failure, or catastrophe. In this study, silicone elastomer O-rings were contaminated with JSC- 1A lunar regolith and their leak rate performance was evaluated. The leak rate values of contaminated O-rings at four levels of seal compression were compared to those of as-received, uncontaminated, O-rings. The results showed a drastic increase in leak rate after contamination. JSC-1A contaminated O-rings lead to immeasurably high leak rate values for all levels of compression except complete closure. Additionally, a mechanical method of simulant removal was examined. In general, this method returned the leak rate to as-received values.
The Environmental Test Facility (ETF), located at NASA-Marshall Space Flight Center, Huntsville, Alabama, has provided thermal vacuum testing for several major programs since the 1960's. The ETF consists of over 13 thermal vacuum chambers sized and configured to handle the majority of test payloads. The majority of tests require a hard vacuum with heating and cryogenics. NASA's Return-to-Flight program requested testing to simulate a launch from the ground to flight using vacuum, heating and cryogenics. This paper describes an effective method for simulating a launch.
Report discusses application of lower-upper (LU) implicit numerical-integration scheme, together with interactive grid-generation method, to simulation of inviscid, compressible flow in two-dimensional model of turbine cascade. Study part of continuing effort to develop techniques for computation of complicated three-dimensional flows in turbomachinery.