Search NASA⌕ Search

SEARCH · Search NASA

Results for “Temperature gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Thermal Conductivity of Ceramic Thermal Barrier and Environmental Barrier Coating Materials

Thermal barrier and environmental barrier coatings (TBC's and EBC's) have been developed to protect metallic and Si-based ceramic components in gas turbine engines from high temperature attack. Zirconia-yttria based oxides and (Ba,Sr)Al2Si2O8(BSAS)/mullite based silicates have been used as the coating materials. In this study, thermal conductivity values of zirconia-yttria- and BSAS/mullite-based coating materials were determined at high temperatures using a steady-state laser heat flux technique. During the laser conductivity test, the specimen surface was heated by delivering uniformly distributed heat flux from a high power laser. One-dimensional steady-state heating was achieved by using thin disk specimen configuration (25.4 mm diam and 2 to 4 mm thickness) and the appropriate backside air-cooling. The temperature gradient across the specimen thickness was carefully measured by two surface and backside pyrometers. The thermal conductivity values were thus determined as a function of temperature based on the 1-D heat transfer equation. The radiation heat loss and laser absorption corrections of the materials were considered in the conductivity measurements. The effects of specimen porosity and sintering on measured conductivity values were also evaluated.

Zhu, Dong-Ming↗
NASA NTRS2003

Flexible Cryogenic Temperature and Liquid-Level Probes

Lightweight, flexible probes have been developed for measuring temperatures at multiple locations in tanks that contain possibly pressurized cryogenic fluids. If the fluid in a given tank is subcritical (that is, if it consists of a liquid and its vapor), then in one of two modes of operation, the temperature measurements made by a probe of this type can be used to deduce the approximate level of the liquid. The temperature sensors are silicon diodes located at intervals along a probe. If the probe is to be used to measure a temperature gradient along a given axis in the tank, then the probe must be mounted along that axis. In the non-liquid-level-sensing temperature-measurement mode, a constant small electric current is applied to each diode and the voltage across the diode . a known function of the current and temperature . is measured as an indication of its temperature. For the purpose of this measurement, "small electric current" signifies a current that is not large enough to cause a significant increase in the measured temperature. More specifically, the probe design calls for a current of 10 A, which, in the cryogenic temperature range of interest, generates heat at a rate of only about 0.01 mW per diode. In the liquid-level-sensing mode, one applies a larger current (30 mA) to each diode so as to heat each diode appreciably (with a power of about 36 mW in the temperature range of interest). Because the liquid cools the diode faster than does the vapor, the temperature of the diode is less when diode is immersed in the liquid than when it is above the surface of the liquid. Thus, the temperature (voltage) reading from each diode can be used to determine whether the liquid level is above or below the diode, and one can deduce that the liquid level lies between two adjacent diodes, the lower one of which reads a significantly lower temperature. The aforementioned techniques for measuring temperature and deducing liquid level are not new. What is new here are the designs of the probes and of associated external electronic circuitry. In each probe, the diodes and the lead wires are embedded in a strong, lightweight, flexible polyimide strip. Each probe is constructed as an integral unit that includes a multipin input/output plug or socket for solderless connection of the lead wires to the external circuitry. The polyimide strip includes mounting tabs with holes that can accommodate rivets, screws, or other fasteners. Alternatively, a probe can be mounted by use of an epoxy. A probe can be manufactured to almost any length or width, and the diodes can be embedded at almost any desired locations along and across the polyimide strip. In designing a probe for a specific application, one seeks a compromise between (1) minimizing the number of diodes in order to minimize the complexity of input/output connections and external electronic circuitry while (2) using enough diodes to obtain the required precision. Optionally, to minimize spurious heating of the cryogenic fluid, the external circuitry can be designed to apply power to the probe only during brief measurement intervals. Assuming that the external circuitry is maintained at a steady temperature, a power-on interval of only a few seconds is sufficient to obtain accurate data on temperatures and/or the height of the liquid/vapor interface.

Haberbusch, Mark↗
NASA NTRS2005

Balloon Ascent: 3-D Simulation Tool for the Ascent and Float of High-Altitude Balloons

The BalloonAscent balloon flight simulation code represents a from-scratch development using Visual Basic 5 as the software platform. The simulation code is a transient analysis of balloon flight, predicting the skin and gas temperatures along with the 3-D position and velocity in a time and spatially varying environment. There are manual and automated controls for gas valving and the dropping of ballast. Also, there are many handy calculators, such as appropriate free lift, and steady-state thermal solutions with temperature gradients. The strength of this simulation model over others in the past is that the infrared environment is deterministic rather than guessed at. The ground temperature is specified along with the emissivity, which creates a ground level IR environment that is then partially absorbed as it travels upward through the atmosphere to the altitude of the balloon.

Farley, Rodger E.↗
DOE OSTI2025

Irradiation Vehicles for Evaluating SiC/SiC Cladding Bowing Under Neutron Flux Gradients

Silicon carbide fiber–reinforced silicon carbide matrix (SiC/SiC) composites are among the most promising candidates for long term accident-tolerant nuclear fuel cladding. A key challenge related to their deployment is lateral bowing caused by differential radiation-induced swelling under dose or temperature gradients, which could obstruct coolant flow or interfere with control rod/blade movements. Although previous modeling efforts have predicted bowing behavior in light-water reactor (LWR) environments, experimental validation remains limited, especially at prototypic LWR temperatures. This study addresses that gap by irradiating six reduced-length SiC/SiC cladding tubes (~600 mm) in the High Flux Isotope Reactor (HFIR) at ~300°C, which is representative of LWR conditions. The tubes will be housed in a sealed vessel with an inert gas gap to maintain target temperatures and prevent direct coolant contact. Arranged in three pairs, each set will receive a different radiation dose (low, medium, high), with the central pair receiving ~0.1 displacements per atom (dpa)—the expected dose for peak bowing. The experiment will determine the dose-dependent bowing behavior and validate predictive finite element models. In this work, the tubes are freely suspended from pins to allow for unconstrained bowing; however, we present a concept for introducing localized constraints to represent grid spacer effects. Post-irradiation examination will include swelling measurements and profilometry to assess bowing and compare the results with model predictions. This work aims to confirm the conditions under which maximum bowing occurs so as to improve the reliability of SiC/SiC performance models in nuclear applications.

Russell, Nick [ORNL] (ORCID:0000000296099820)↗
DOE OSTI2024

The effect of temperature oscillations on energy storage rectification in harmonic systems

Abstract Rectification, the preferential transport of a current in one direction through a system, has garnered significant attention in molecules because of its importance for controlling thermal and electronic currents at the nanoscale. Here, we report the presence of energy storage rectification effects in a molecular chain. This phenomenon is generated by subjecting a harmonic molecular chain to an oscillating temperature gradient and showing that the energy absorption rate of the system depends on the direction of the gradient. We examine how the energy storage rectification ratios in the chain are affected by the oscillating gradient, asymmetry in the chain, and the system parameters. We find that energy storage rectification can be observed in harmonic lattice structures with time-dependent temperatures and that, correspondingly, anharmonicity is not required to generate this rectification mechanism in such systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1997

Nonlinear Transient Thermal Analysis by the Force-Derivative Method

High-speed vehicles such as the Space Shuttle Orbiter must withstand severe aerodynamic heating during reentry through the atmosphere. The Shuttle skin and substructure are constructed primarily of aluminum, which must be protected during reentry with a thermal protection system (TPS) from being overheated beyond the allowable temperature limit, so that the structural integrity is maintained for subsequent flights. High-temperature reusable surface insulation (HRSI), a popular choice of passive insulation system, typically absorbs the incoming radiative or convective heat at its surface and then re-radiates most of it to the atmosphere while conducting the smallest amount possible to the structure by virtue of its low diffusivity. In order to ensure a successful thermal performance of the Shuttle under a prescribed reentry flight profile, a preflight reentry heating thermal analysis of the Shuttle must be done. The surface temperature profile, the transient response of the HRSI interior, and the structural temperatures are all required to evaluate the functioning of the HRSI. Transient temperature distributions which identify the regions of high temperature gradients, are also required to compute the thermal loads for a structural thermal stress analysis. Furthermore, a nonlinear analysis is necessary to account for the temperature-dependent thermal properties of the HRSI as well as to model radiation losses.

Balakrishnan, Narayani V.↗
NASA NTRS1999

Climate Change and the Brewer-Dobson Circulation

Using GCM (General Circulation Model) simulations of the troposphere-stratosphere circulation in different climate regimes, the sensitivity of the Brewer-Dobson Circulation to climate change will be discussed. Included will be simulations of the stratosphere with increasing/doubled CO2 as done with different versions of the GISS (Goddard Institute for Space Studies) Global Climate Middle Atmosphere Model, with and without ozone response. To put the results in a broader perspective, stratospheric circulation changes from several paleoclimate simulations will also be presented, including the Last Glacial Maximum and the Paleocene, each with several different (plausible) latitudinal sea surface temperature gradients. Hence the climate changes investigated will include strong variations in baroclinic and topographic tropospheric planetary wave and gravity wave forcing, as well as global mean temperature and atmospheric CO2 levels. Results will be analyzed in terms of wave driving via E-P flux convergences and gravity wave effects, and will be shown to be strongly dependent on wave propagation characteristics.

Rind, David↗
NASA NTRS1999

Climate Change and the Brewer-Dobson Circulation

Using GCM simulations of the troposphere-stratosphere circulation in different climate regimes, the sensitivity of the Brewer-Dobson Circulation to climate change will be discussed. Included will be simulations of the stratosphere with increasing/doubled C02 as done with different versions of the GISS Global Climate Middle Atmosphere Model, with and without ozone response. To put the results in a broader perspective, stratospheric circulation changes from several paleoclimate simulations will also be presented, including the Last Glacial Maximum and the Paleocene, each with several different (plausible) latitudinal sea surface temperature gradients. Hence the climate changes investigated will include strong variations in baroclinic and topographic tropospheric planetary wave and gravity wave forcing, as well as global mean temperature and atmospheric C02 levels. Results will be analyzed in terms of wave driving via E-P flux convergences and gravity wave effects, and will be shown to be strongly dependent on wave propagation characteristics.

Rind, David↗
NASA NTRS2012

Quantitative Infrared Image Analysis Of Thermally-Thin Cellulose Surface Temperatures During Upstream and Downstream Microgravity Flame Spread from A Central Ignition Line

Surface view calibrated infrared images of ignition and flame spread over a thin cellulose fuel were obtained at 30 Hz during microgravity flame spread tests in the 10 second Japan Microgravity Center (JAMIC). The tests also used a color video of the surface view and color images of the edge view using 35 millimeter 1600 Kodak Ektapress film at 2 Hz. The cellulose fuel samples (50% long fibers from lumi pine and 50% short fibers from birch) were made with an area density of 60 grams per square meters. The samples were mounted in the center of a 12 centimeter wide by 16 centimeter tall flow duct that uses a downstream fan to draw the air through the flow duct. Samples were ignited after the experiment package was released using a straight hot wire across the center of the 7.5 centimeter wide by 14 centimeter long samples. One case, at 1 atmosphere 35%O2 in N2, at a forced flow of 10 centimeters per second, is presented here. In this case, as the test progresses, the single flame begins to separate into simultaneous upstream and downstream flames. Surface temperature profiles are evaluated as a function of time, and temperature gradients for upstream and downstream flame spread are measured. Flame spread rates from IR image data are compared to visible image spread rate data. IR blackbody temperatures are compared to surface thermocouple readings to evaluate the effective emissivity of the pyrolyzing surface. Preheat lengths are evaluated both upstream and downstream of the central ignition point. A surface energy balance estimates the net heat flux from the flame to the fuel surface along the length of the fuel.

Olson, Sandra L.↗
NASA NTRS2013

Quantitative Infrared Image Analysis Of Simultaneous Upstream and Downstream Microgravity Flame Spread over Thermally-Thin Cellulose in Low Speed Forced Flow

The effect of low velocity forced flow on microgravity flame spread is examined using quantitative analysis of infrared video imaging. The objective of the quantitative analysis is to provide insight into the mechanisms of flame spread in microgravity where the flame is able to spread from a central location on the fuel surface, rather than from an edge. Surface view calibrated infrared images of ignition and flame spread over a thin cellulose fuel were obtained along with a color video of the surface view and color images of the edge view using 35 mm color film at 2 Hz. The cellulose fuel samples were mounted in the center of a 12 cm wide by 16 cm tall flow duct and were ignited in microgravity using a straight hot wire across the center of the 7.5 cm wide by 14 cm long samples. Four cases, at 1 atm. 35%O2 in N2, at forced flows from 2 cm/s to 20 cm/s are presented here. This flow range captures flame spread from strictly upstream spread at low flows, to predominantly downstream spread at high flow. Surface temperature profiles are evaluated as a function of time, and temperature gradients for upstream and downstream flame spread are measured. Flame spread rates from IR image data are compared to visible image spread rate data. IR blackbody temperatures are compared to surface thermocouple readings to evaluate the effective emissivity of the pyrolyzing surface. Preheat lengths and pyrolysis lengths are evaluated both upstream and downstream of the central ignition point. A surface energy balance estimates the net heat flux from the flame to the fuel surface along the length of the fuel. Surface radiative loss and gas-phase radiation from soot are measured relative to the net heat feedback from the flame. At high surface heat loss relative to heat feedback, the downstream flame spread does not occur.

Olson, S. L.↗
DOE OSTI2025

Multiphase computational fluid dynamics modeling of reacting flows in absorption columns for carbon capture

First-principles derived computational fluid dynamics (CFD) simulations have been proposed as a fundamental tool for investigating solvent-based CO 2 absorption in packed columns due to their ability to accurately represent the underlying nonlinear, multiscale dynamics. Numerous studies have previously utilized such CFD simulations to investigate hydrodynamics of columns with structured and random packings by assessing the key hydrodynamic metrics such as the interfacial and wetted areas. While mapping such metrics for different conditions is essential to the optimization of absorption columns, it is not sufficient, as the CO 2 capture rate depends also on the coupled, nonlinear dynamics from the underlying chemical reaction kinetics, thermodynamics, and heat-transfer rates. In this work, we present detailed CFD simulation results augmented by incorporating the effects of interfacial physical mass transfer of CO 2 , heat release from chemical reaction kinetics, and thermophysical property variations from resulting temperature gradients. We demonstrate the applicability of the proposed approach in numerically assessing the performance of packed columns by evaluating key hydrodynamic quantities, CO 2 absorption rates, and temperature rise in a reference column with packings that are structurally similar to the Sulzer Mellapak™ 250.Y packing, for different solvent inflow velocities and temperatures. Predictions from simulation results are found to be consistent with the trends in experimental observations from the literature, suggesting that the predictive capabilities of the simulation framework can be leveraged to guide the future development of absorber-column designs and optimized process flowsheets.

Absorption columns↗
NASA NTRS1992

Effects of buoyancy-driven flow and thermal boundary conditions on physical vapor transport

A 2D numerical model was developed in order to ascertain if reduced gravity conditions are beneficial to physical vapor transport (PVT) and to determine its tolerance limits to residual accelerations. This was solved using the PHOENICS finite-volume code. Reduction of gravitational accelerations to less than 0.1 g0 was found to be sufficient to suppress buoyancy-driven convection to an extent that diffusion was the dominant transport mode, whence a greater uniformity in the growth rate could be obtained. It is shown that a uniform temperature gradient on the ampoule walls causes the vapor to be supersaturated throughout the ampoule, potentially resulting in undesirable nucleation at the walls. A 'hump' in the wall temperature profile can be used to avoid this. The prevailing transport conditions determine the size of the hump needed.

Nadarajah, Arunan↗
NASA NTRS2004

Direct Observation of Controlled Melting and Resolidification of Succinonitrile Mixtures in a Microgravity Environment

In support of the Pore Formation and Mobility Investigation (PFMI) direct observation of experiments on the controlled melting and subsequent resolidification of succinonitrile were conducted in the glovebox facility (GBX) of the International Space Station (ISS). Samples were prepared on ground by filling glass tubes, 1 cm ID and approximately 30 cm in length, with pure succinonitrile (SCN) and SCN-Water mixtures under 450 millibar of nitrogen. Experimental processing parameters of temperature gradient and translation speed, as well as camera settings, were remotely monitored and manipulated from the ground Telescience Center (TSC) at the Marshall Space Flight Center. Sample temperatures are monitored by six in situ thermocouples. Real time visualization during melt back revealed bubbles of different sizes initiating at the solid/liquid interface, their release, interactions, and movement into the temperature field ahead of them. Subsequent re-solidification examined planar interface breakdown and the transition to steady-state dendritic growth. A preliminary analysis of the observed phenomena and its implication to future microgravity experiments is presented and discussed.

Grugel, R. N.↗
NASA NTRS2000

Monitoring Geothermal Features in Yellowstone National Park with ATLAS Multispectral Imagery

The National Park Service (NPS) must produce an Environmental Impact Statement for each proposed development in the vicinity of known geothermal resource areas (KGRAs) in Yellowstone National Park. In addition, the NPS monitors indicator KGRAs for environmental quality and is still in the process of mapping many geothermal areas. The NPS currently maps geothermal features with field survey techniques. High resolution aerial multispectral remote sensing in the visible, NIR, SWIR, and thermal spectral regions could enable YNP geothermal features to be mapped more quickly and in greater detail In response, Yellowstone Ecosystems Studies, in partnership with NASA's Commercial Remote Sensing Program, is conducting a study on the use of Airborne Terrestrial Applications Sensor (ATLAS) multispectral data for monitoring geothermal features in the Upper Geyser Basin. ATLAS data were acquired at 2.5 meter resolution on August 17, 2000. These data were processed into land cover classifications and relative temperature maps. For sufficiently large features, the ATLAS data can map geothermal areas in terms of geyser pools and hot springs, plus multiple categories of geothermal runoff that are apparently indicative of temperature gradients and microbial matting communities. In addition, the ATLAS maps clearly identify geyserite areas. The thermal bands contributed to classification success and to the computation of relative temperature. With masking techniques, one can assess the influence of geothermal features on the Firehole River. Preliminary results appear to confirm ATLAS data utility for mapping and monitoring geothermal features. Future work will include classification refinement and additional validation.

Spruce, Joseph↗
NASA NTRS2022

The Influence of Recent and Future Climate Change on Spring Arctic Cyclones

In recent decades, the Arctic has experienced rapid atmospheric warming and sea ice loss, with an ice-free Arctic projected by the end of this century. Cyclones are synoptic weather events that transport heat and moisture into the Arctic, and have complex impacts on sea ice, and the local and global climate. However, the effect of a changing climate on Arctic cyclone behavior remains poorly understood. This study uses high resolution (4 km), regional modeling techniques and downscaled global climate reconstructions and projections to examine how recent and future climatic changes alter cyclone behavior. Results suggest that recent climate change has not yet had an appreciable effect on Arctic cyclone characteristics. However, future sea ice loss and increasing surface temperatures drive large increases in the near-surface temperature gradient, sensible and latent heat fluxes, and convection during cyclones. The future climate can alter cyclone trajectories and increase and prolong intensity with greatly augmented wind speeds, temperatures, and precipitation. Such changes in cyclone characteristics could exacerbate sea ice loss and Arctic warming through positive feedbacks. The increasing extreme nature of these weather events has implications for local ecosystems, communities, and socio-economic activities.

Chelsea L Parker↗
DOE OSTI2026

Routes to high-performance operation in Wendelstein 7-X: turbulence suppression with shaping of the density profile

Steep density gradients generally lead to improved plasma performance in the neoclassically optimized stellarator W7-X. This is evident in the global energy confinement time as well as in the ion temperature and can be explained by a strong reduction of the ion temperature gradient turbulence. Such conditions can experimentally be realized by several methods: injection of cryogenic hydrogen pellets, appropriate combination of neutral beam and electron cyclotron resonance heating (ECRH) and, in some cases, with low power of ECRH after preconditioning of the first wall. The duration of the improved phases is determined by the ability to sustain the steep density gradient, by technical limitations of the involved systems and, eventually, by the plasma stability. This paper gives an overview of relevant experimental results and presents example discharges where the improved confinement conditions could be extended to multiple seconds: up to 4 s using neutral beam injection and from 14 to 40 s with steady state pellet injection. In these plasmas the turbulent thermal diffusivity is reduced by a factor of 3 to 4 in a broad radial range, which allows high ion temperatures of up to 3 keV at the densities of about 1.5 • 10 20 m −3 .

high performance plasma↗
DOE OSTI2024

Ion-temperature- and density-gradient-driven instabilities and turbulence in Wendelstein 7-X close to the stability threshold

Electrostatic gyrokinetic instabilities and turbulence in the Wendelstein 7-X stellarator are studied. Particular attention is paid to the ion-temperature-gradient (ITG) instability and its character close to marginal stability [Floquet-type turbulence (Zocco et al., Phys. Rev. E, vol. 106, 2022, p. L013202) with no electron temperature gradient]. The flux tube version of the δƒ code stella (Barnes et al., J. Comput. Phys., vol. 391, 2019, pp. 365–380) is used to run linear and nonlinear gyrokinetic simulations with kinetic electrons. The nature of the dominant instability depends on the wavelength perpendicular to the magnetic field, and the results are conveniently displayed in stability diagrams that take this dependence into account. This approach highlights the presence of universal instabilities, which are less unstable but have longer wavelengths than other modes. A quasi-linear estimate of the heat flux suggests they are relevant for transport. Close to the stability threshold, the linear eigenmodes and turbulence form highly extended structures along the computational domain if the magnetic shear is small. Numerical experiments and diagnostics are undertaken to assess the resulting radial localisation of the turbulence, which affects the interaction of the latter with zonal flows. Increasing the amplitude of the magnetic shear (e.g.through current drive) has a stabilising effect on the turbulence and, thus, reduces the nonlinear energy transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1974

Thermocapillary convection in weightless condition

Results are presented of studies on thermocapillary instability of a liquid in a spherical layer with free surface and convection in a rectangular channel with horizontal temperature gradient. It is shown that in vessels partly filled with a viscous incompressible fluid and under essentially weightless conditions free convection may arise due to the surface tension temperature dependence.

Babskiy, V. G.↗